Removal of Co(Ⅱ) from aqueous solutions by complexation-ultrafiltration was investigated using polyacrylic acid sodium(PAAS) as complexing agent with the help of rotating disk membrane,and the shear ability of PAA-Co...Removal of Co(Ⅱ) from aqueous solutions by complexation-ultrafiltration was investigated using polyacrylic acid sodium(PAAS) as complexing agent with the help of rotating disk membrane,and the shear ability of PAA-Co complex was studied. The effects of the mass ratio of PAAS to Co(Ⅱ)(P/M) and pH on the rejection of Co(Ⅱ) were studied,and the optimum conditions were P/M=8 and pH=7. The rejection of Co(Ⅱ) was over 97% when the rotating speed of the disk(n)was less than 710 r/min at the optimum P/M and pH. The distribution of the forms of cobalt on the membrane surface was established by the membrane partition model, and the critical shear rate,the smallest shear rate at which the PAA-Co complex begins to dissociate,was calculated to be1.4×10^4 s^-1,and the corresponding rotating speed was 710 r/min.The PAA-Co complex dissociated when the shear rate was greater than the critical one. The regeneration of PAAS and recovery of Co(Ⅱ) were achieved by shear-induced dissociation and ultrafiltration.展开更多
Removal of cadmium(Ⅱ) ions from dilute aqueous solutions by complexation–ultrafiltration using rotating disk membrane was investigated. Polyacrylic acid sodium(PAAS) was used as complexation agent, as key factors of...Removal of cadmium(Ⅱ) ions from dilute aqueous solutions by complexation–ultrafiltration using rotating disk membrane was investigated. Polyacrylic acid sodium(PAAS) was used as complexation agent, as key factors of complexation, pH and the mass ratio of PAAS to Cd^(2+)(P/M) were studied, and the optimum complexation–ultrafiltration conditions were obtained. The effects of rotating speed(n) on the stability of PAA–Cd complex was studied with two kinds of rotating disk, disk Ⅰ(without vane) and disk Ⅱ(with six rectangular vanes) at a certain range of rotating speed. Both of the rejection could reach 99.7% when n was lower than 2370 r·min^(-1) and 1320 r·min^(-1), for disk I and disk Ⅱ, respectively. However, when rotating speed exceeds a certain value,the critical rotating speed(n_c), the rejection of Cd(Ⅱ) decreases greatly. The distribution of form of cadmium on the membrane was established by the membrane partition model, and the critical shear rate(γ_c), the smallest shear rate at which the PAA–Cd complex begins to dissociate, was calculated based on the membrane partition model and mass balance. The critical shear rates(γ_c) of PAA–Cd complex were 5.9 × 10~4 s^(-1), 1.01 × 10~5 s^(-1),and 1.31 × 10~5 s^(-1) at pH = 5.0, 5.5, and 6.0, respectively. In addition, the regeneration of PAAS was achieved by shear induced dissociation and ultrafiltration.展开更多
Copolymer of acrylic acid and maleic acid(PMA)was used to remove Hg^2+from aqueous solution by complexation-ultrafiltration(C-UF)through rotating disk membrane(RDM).The effects of P/M(mass ratio of PMA to metal ions),...Copolymer of acrylic acid and maleic acid(PMA)was used to remove Hg^2+from aqueous solution by complexation-ultrafiltration(C-UF)through rotating disk membrane(RDM).The effects of P/M(mass ratio of PMA to metal ions),pH and rotation speed(N)on the interception of Hg^2+were investigated.The interception could reach 99.7%at pH 7.0,P/M 6 and N less than 1890 r/min.The shear stability of PMA-Hg complex was studied by RDM.The critical rotation speed,at which the interception starts to decrease,was 1890 r/min,and the critical shear rate,the smallest shear rate at which PMA-Hg complex begins to dissociate,was 2.50×10^5s^-1 at pH 7.0.Furthermore,the critical radii were obtained at different rotation speeds and pHs.The results showed that the critical radius decreased with the rotation speed and increased with pH.Shear induced dissociation coupling with ultra?ltration(SID-UF)was efficiently used to recover Hg^2+and PMA.展开更多
Tensile and fracture behaviors of sandwich-structured composites consisting of a Fe-based amorphous layer with a constant thickness and ultrafine-grained Ni layers with different thicknesses were investigated. The res...Tensile and fracture behaviors of sandwich-structured composites consisting of a Fe-based amorphous layer with a constant thickness and ultrafine-grained Ni layers with different thicknesses were investigated. The results indicate that the initiation and the stable propagation of the shear band in the amorphous layer was dominated by the Ni layers due to their strong constraint role. The catastrophic fracture of the amorphous layer was postponed in the sandwich composites through properly increasing the constrained Ni layer thickness, which effectively decreased the shear stress on the shear fracture planes of the amorphous layer, and thus led to stable propagation of the primary SB characterized by the increase in the smooth region size of the shear band.展开更多
According to the observation in experiment of stability of the oil film, the assumption of velocity distribution for both the water flow and the oil film is introduced. On the basis of the assumption, Orr-Sommerfeld s...According to the observation in experiment of stability of the oil film, the assumption of velocity distribution for both the water flow and the oil film is introduced. On the basis of the assumption, Orr-Sommerfeld stability equation is applied to develop the method of determining the critical velocity of the oil film, and the criterion for stability of the oil film is obtained. Meanwhile, a formula describing the relation between the thickness of the oil film and the velocity of the water flow is also given and examined by the laboratory experiment.展开更多
Based on the hydrodynamic stability theory of distorted laminar flow and the kind of distortion profiles on the mean velocity in parallel shear flow given in paper [1], this paper investigates the linear stability beh...Based on the hydrodynamic stability theory of distorted laminar flow and the kind of distortion profiles on the mean velocity in parallel shear flow given in paper [1], this paper investigates the linear stability behaviour of parallel shear flow, presents unstable results of plane Couette flow and pipe Poiseuille flow to two-dimensional or axisymmetric disturbances for the first time, and obtains neutral curves of these two motions under certain definition.展开更多
Based on the hydrodynamic stability theory of distorted laminar flow and the kind of distortion profiles on the mean velocity in parallel shear flow given in paper [1], this paper investigates the nonlinear stability ...Based on the hydrodynamic stability theory of distorted laminar flow and the kind of distortion profiles on the mean velocity in parallel shear flow given in paper [1], this paper investigates the nonlinear stability behaviour of parallel shear flow, carries on stability calculation taking account of the perturbations of background turbulence noise under certain assumption, and obtains some results in accordance qualitatively with those of experiment for plane Poiseuille flow and pipe Poiseuille flow.展开更多
By using oxalate group-modified TiO2 nanoparticles as the dispersing phase, different kinds of silicone oil with various viscosities and terminal groups（hydroxyl, hydrogen, and methyl） were used as the dispersing me...By using oxalate group-modified TiO2 nanoparticles as the dispersing phase, different kinds of silicone oil with various viscosities and terminal groups（hydroxyl, hydrogen, and methyl） were used as the dispersing media to prepare different electrorheological（ER） fluids. Their zero-field viscosity, yield stress under direct current electric fields, ER efficiency, shear stability, leakage current density, and sedimentation stability were tested to study the effect of carrier liquid on the properties of ER fluids. The results indicate that the zerofield viscosity, the yield stress, and the leakage current density increase with increasing viscosity of the silicone oils. The effects of the viscosity on the ER efficiency, the shear stability, and the sedimentation ratio depend on the competition between the viscous resistance and the aggregation of the particles. Among the three ER fluids prepared with silicone oil with different terminal groups, hydroxyl-terminated oil based sample has the highest zero-field viscosity, the highest field-induced yield stress and ER efficiency, the largest current density, and the best sedimentation stability.展开更多
This work established a quantitative method to access the shear stability of aerobic granular sludge(AGS)and validated its feasibility by using the mature AGS from a pilot-scale(50 tons/day)membrane bioreactor(MBR)for...This work established a quantitative method to access the shear stability of aerobic granular sludge(AGS)and validated its feasibility by using the mature AGS from a pilot-scale(50 tons/day)membrane bioreactor(MBR)for treating real municipal wastewater.The results showed that the changing rate( S)of the peak area(S)of granule size distribution(GSD)exhibited an exponential relationship(R^(2)≥0.76)with the shear time(y=a−b·c^(x)),which was a suitable indicative index to reflect the shear stability of different AGS samples.The limiting granule size(LGS)was defined and proposed to characterize the equilibrium size for AGS after being sheared for a period of time,whose value in terms of Dv50 showed high correlation(R^(2)=0.92)with the parameter a.The free Ca^(2+)(28.44-34.21 mg/L)in the influent specifically interacted with polysaccharides(PS)in the granule’s extracellular polymeric substance(EPS)as a nucleation site,thereby inducing the formation of Ca precipitation to enhance its Young’s modulus,while Ca^(2+) primarily interacted with PS in soluble metabolic product(SMP)during the initial granulation process.Furthermore,the Young’s modulus significantly affected the parameter a related to shear stability(R^(2)=0.99).Since the parameter a was more closely related(R^(2)=1.00)to S than that of the parameter b or c,the excellent correlation(R^(2)=0.99)between the parameter a and the wet density further verified the feasibility of this method.展开更多
In an experimental realization of the sheared cylindrical slab, the level of plasma turbulence is strongly reduced by application of a sufficient bias potential difference in the radial direction. Density fluctuation ...In an experimental realization of the sheared cylindrical slab, the level of plasma turbulence is strongly reduced by application of a sufficient bias potential difference in the radial direction. Density fluctuation levels △nrms/n decrease by more than a factor of five. The ion flow velocity profile is measured spectroscopically from the Doppler shift of an argon ion line. Comparison of the shearing rates with the turbulent amplitudes as a function of bias show no relation between the shearing rate and turbulence reduction, contrary to expectations.展开更多
Internal transport barriers （ITBs） are phenomena associated with improved confinement mode of tokamak plasmas. Within the region where the ITB locates, the plasma pressure has a large gradient while the magnetic she...Internal transport barriers （ITBs） are phenomena associated with improved confinement mode of tokamak plasmas. Within the region where the ITB locates, the plasma pressure has a large gradient while the magnetic shear s has a minimum so that within and near the ITB, the absolute value of the shear is very low. Physics involved is plentiful, from the macroscopic （ MHD ） stability, to the suppression of microscopic instabilities thought to be responsible for anomalous transport. The treatment of very low shear also poses some theoretical difficulties.展开更多
Partially hydrolyzed polyacrylamide（HPAM）as the main component of slickwater fracturing fluid is a shear-sensitive polymer,which suffers from mechanical degradation at turbulent flow rates.Five different concentrati...Partially hydrolyzed polyacrylamide（HPAM）as the main component of slickwater fracturing fluid is a shear-sensitive polymer,which suffers from mechanical degradation at turbulent flow rates.Five different concentrations of HPAM as well as mixtures of polyacrylamide/xanthan gum were prepared to investigate the possibility of improving shear stability of HPAM.Drag reduction（DR）measurements were performed in a closed flow loop.For HPAM solutions,the extent of DR increased from 30%to67%with increasing HPAM concentration from 100 to1000 wppm.All the HPAM solutions suffered from mechanical degradation and loss of DR efficiency over the shearing period.Results indicated that the resistance to shear degradation increased with increasing polymer concentration.DR efficiency of 600 wppm xanthan gum（XG）was 38%,indicating that XG was not as good a drag reducer as HPAM.But with only 6%DR decline,XG solution exhibited a better shear stability compared to HPAM solutions.Mixed HPAM/XG solutions initially exhibited greater DR（40%and 55%）compared to XG,but due to shear degradation,DR%dropped for HPAM/XG solutions.Compared to 200 wppm HPAM solution,addition of XG did not improve the drag reduction efficiency of HPAM/XG mixed solutions though XG slightly improved the resistance against mechanical degradation in HPAM/XG mixed polymer solutions.展开更多
Viscosity index (VI) and shear stability index (SSI) are standard methods used in the lubricant industry to determine temperature-viscosity dependency and resistance to product degradation, respectively. A variety of ...Viscosity index (VI) and shear stability index (SSI) are standard methods used in the lubricant industry to determine temperature-viscosity dependency and resistance to product degradation, respectively. A variety of oil-soluble polymers, including poly(alkyl methacrylates) (PAMAs) are routinely used to control these properties in fully-formulated liquid lubricants. In this report, we use reversible addition-fragmentation chain transfer (RAFT) polymerization to precisely target identical degrees of polymerization in a family of PAMAs with varying lauryl, hexyl, butyl, ethyl, and methyl groups. Then, expanding on previous methodology reported in the literature, we establish structure property relationships for these PAMAs, specifically looking at how intrinsic viscosity [η] and Martin interaction parameters K<sub>M</sub> relate to VI and SSI characteristics. While the intrinsic viscosity [η] is associated with the volume of macromolecules at infinite dilution, the parameter K<sub>M</sub> reflects the hydrodynamic interactions of polymer chains at actual polymer concentrations in lubricating oils. In this paper, we show that the dependence of VI on the non-dimensional concentration c/c* (or c[η]) can be presented in a form of master curve with shift factors proportional to K<sub>M</sub> that decreases with increasing size of alkyl groups. This finding implies that even in the dilute regime, the coil-expansion theory used to explain the effect of macromolecules on VI should be complemented with the idea of hydrodynamic interactions between polymer molecules that can be controlled by the choice of alkyl chains in the family of PAMAs.展开更多
In this paper, four kinds of polymethacrylates(PMAs) used as multifunctional additives were synthesized from quaternary C1—C14 methacrylate, among which sample 4 exhibited relatively better performance. According to ...In this paper, four kinds of polymethacrylates(PMAs) used as multifunctional additives were synthesized from quaternary C1—C14 methacrylate, among which sample 4 exhibited relatively better performance. According to the methacrylate ratio of sample 4, the optimized reaction conditions of PMA were explored by orthogonal experiments comprising 4 factors and 3 levels, and the optimized reaction conditions covered an initiator dosage of 0.8 %, a molecular weight regulator dosage of 0.4%, a reaction temperature of 95 ℃ and a reaction time of 8.5 h. When the optimized PMA samples were used to formulate the 75W/90 automotive gear base oil, they exhibited improved shear stability and good low temperature property. In comparison with foreign commercial polymethacrylate GP, the optimized PMA samples exhibited better thickening ability, similar shear stability and slightly weak low temperature property, with their performance being the same as GP's on the whole. The slight difference in the performance between the optimized PMA and GP was attributed to the difference of chain length of copolymers and the distribution of relative molecular mass between them.展开更多
Ir-Ni-Ta metallic glasses(MGs)exhibit an array of superior high-temperature properties,making them attractive for applications at high temperatures or in harsh environments.However,Ir-Ni-Ta bulk MGs are quite brittle ...Ir-Ni-Ta metallic glasses(MGs)exhibit an array of superior high-temperature properties,making them attractive for applications at high temperatures or in harsh environments.However,Ir-Ni-Ta bulk MGs are quite brittle and often fracture catastrophically even before plastic yielding,significantly undercutting their high-strength advantage.Here,we show that the Ir-Ni-Ta MGs are not intrinsically brittle,but rather malleable when the feature size is reduced to micro/nano-scales.All tested Ir-Ni-Ta MG micropillars with a diameter ranging from~500 nm to~5μm display a large plastic strain above 25%(the maximum up to 35%),together with a yield strength up to 7 GPa,well exceeding the strength recorded in most metallic materials.The intrinsic shear stability of Ir-Ni-Ta MGs,as characterized by the normalized shear displacement during a shear event,is much larger than those malleable Zr-and Cu-based MGs.Our results suggest that Ir-Ni-Ta MGs are excellent candidates for micro/nanoscale structural applications used at high-temperature or extreme conditions.展开更多
The linear instabilities of incompressible confluent mixing layer and boundary layer were analyzed.The mixing layers include wake,shear layer and their combination.The mean velocity profile of confluent flow is taken ...The linear instabilities of incompressible confluent mixing layer and boundary layer were analyzed.The mixing layers include wake,shear layer and their combination.The mean velocity profile of confluent flow is taken as a superposition of a hyperbolic and exponential function to model a mixing layer and the Blasius similarity solution for a flat plate boundary layer.The stability equation of confluent flow was solved by using the global numerical method.The unstable modes associated with both the mixing and boundary layers were identified.They are the boundary layer mode,mixing layer mode 1（nearly symmetrical mode）and mode 2（nearly anti-symmetrical mode）.The interactions between the mixing layer stability and the boundary layer stability were examined.As the mixing layer approaches the boundary layer,the neutral curves of the boundary layer mode move to the upper left,the resulting critical Reynolds number decreases,and the growth rate of the most unstable mode increases.The wall tends to stabilize the mixing layer modes at low frequency.In addition,the mode switching behavior of the relative level of the spatial growth rate between the mixing layer mode 1 and mode 2 with the velocity ratio is found to occur at low frequency.展开更多
基金Project(24176265)supported by the National Natural Science Foundation of China
文摘Removal of Co(Ⅱ) from aqueous solutions by complexation-ultrafiltration was investigated using polyacrylic acid sodium(PAAS) as complexing agent with the help of rotating disk membrane,and the shear ability of PAA-Co complex was studied. The effects of the mass ratio of PAAS to Co(Ⅱ)(P/M) and pH on the rejection of Co(Ⅱ) were studied,and the optimum conditions were P/M=8 and pH=7. The rejection of Co(Ⅱ) was over 97% when the rotating speed of the disk(n)was less than 710 r/min at the optimum P/M and pH. The distribution of the forms of cobalt on the membrane surface was established by the membrane partition model, and the critical shear rate,the smallest shear rate at which the PAA-Co complex begins to dissociate,was calculated to be1.4×10^4 s^-1,and the corresponding rotating speed was 710 r/min.The PAA-Co complex dissociated when the shear rate was greater than the critical one. The regeneration of PAAS and recovery of Co(Ⅱ) were achieved by shear-induced dissociation and ultrafiltration.
基金Supported by the National Natural Science Foundation of China(21476265)
文摘Removal of cadmium(Ⅱ) ions from dilute aqueous solutions by complexation–ultrafiltration using rotating disk membrane was investigated. Polyacrylic acid sodium(PAAS) was used as complexation agent, as key factors of complexation, pH and the mass ratio of PAAS to Cd^(2+)(P/M) were studied, and the optimum complexation–ultrafiltration conditions were obtained. The effects of rotating speed(n) on the stability of PAA–Cd complex was studied with two kinds of rotating disk, disk Ⅰ(without vane) and disk Ⅱ(with six rectangular vanes) at a certain range of rotating speed. Both of the rejection could reach 99.7% when n was lower than 2370 r·min^(-1) and 1320 r·min^(-1), for disk I and disk Ⅱ, respectively. However, when rotating speed exceeds a certain value,the critical rotating speed(n_c), the rejection of Cd(Ⅱ) decreases greatly. The distribution of form of cadmium on the membrane was established by the membrane partition model, and the critical shear rate(γ_c), the smallest shear rate at which the PAA–Cd complex begins to dissociate, was calculated based on the membrane partition model and mass balance. The critical shear rates(γ_c) of PAA–Cd complex were 5.9 × 10~4 s^(-1), 1.01 × 10~5 s^(-1),and 1.31 × 10~5 s^(-1) at pH = 5.0, 5.5, and 6.0, respectively. In addition, the regeneration of PAAS was achieved by shear induced dissociation and ultrafiltration.
基金Project(21476265)supported by the National Natural Science Foundation of China。
文摘Copolymer of acrylic acid and maleic acid(PMA)was used to remove Hg^2+from aqueous solution by complexation-ultrafiltration(C-UF)through rotating disk membrane(RDM).The effects of P/M(mass ratio of PMA to metal ions),pH and rotation speed(N)on the interception of Hg^2+were investigated.The interception could reach 99.7%at pH 7.0,P/M 6 and N less than 1890 r/min.The shear stability of PMA-Hg complex was studied by RDM.The critical rotation speed,at which the interception starts to decrease,was 1890 r/min,and the critical shear rate,the smallest shear rate at which PMA-Hg complex begins to dissociate,was 2.50×10^5s^-1 at pH 7.0.Furthermore,the critical radii were obtained at different rotation speeds and pHs.The results showed that the critical radius decreased with the rotation speed and increased with pH.Shear induced dissociation coupling with ultra?ltration(SID-UF)was efficiently used to recover Hg^2+and PMA.
基金supported by the National Natural Science Foundation of China(NSFC,Grant Nos.51571199 and 51671050)supported by NSFC(Grant No.51601198)
文摘Tensile and fracture behaviors of sandwich-structured composites consisting of a Fe-based amorphous layer with a constant thickness and ultrafine-grained Ni layers with different thicknesses were investigated. The results indicate that the initiation and the stable propagation of the shear band in the amorphous layer was dominated by the Ni layers due to their strong constraint role. The catastrophic fracture of the amorphous layer was postponed in the sandwich composites through properly increasing the constrained Ni layer thickness, which effectively decreased the shear stress on the shear fracture planes of the amorphous layer, and thus led to stable propagation of the primary SB characterized by the increase in the smooth region size of the shear band.
文摘According to the observation in experiment of stability of the oil film, the assumption of velocity distribution for both the water flow and the oil film is introduced. On the basis of the assumption, Orr-Sommerfeld stability equation is applied to develop the method of determining the critical velocity of the oil film, and the criterion for stability of the oil film is obtained. Meanwhile, a formula describing the relation between the thickness of the oil film and the velocity of the water flow is also given and examined by the laboratory experiment.
文摘Based on the hydrodynamic stability theory of distorted laminar flow and the kind of distortion profiles on the mean velocity in parallel shear flow given in paper [1], this paper investigates the linear stability behaviour of parallel shear flow, presents unstable results of plane Couette flow and pipe Poiseuille flow to two-dimensional or axisymmetric disturbances for the first time, and obtains neutral curves of these two motions under certain definition.
文摘Based on the hydrodynamic stability theory of distorted laminar flow and the kind of distortion profiles on the mean velocity in parallel shear flow given in paper [1], this paper investigates the nonlinear stability behaviour of parallel shear flow, carries on stability calculation taking account of the perturbations of background turbulence noise under certain assumption, and obtains some results in accordance qualitatively with those of experiment for plane Poiseuille flow and pipe Poiseuille flow.
基金Funded by the National Natural Science Foundation of China(51478088)
文摘By using oxalate group-modified TiO2 nanoparticles as the dispersing phase, different kinds of silicone oil with various viscosities and terminal groups（hydroxyl, hydrogen, and methyl） were used as the dispersing media to prepare different electrorheological（ER） fluids. Their zero-field viscosity, yield stress under direct current electric fields, ER efficiency, shear stability, leakage current density, and sedimentation stability were tested to study the effect of carrier liquid on the properties of ER fluids. The results indicate that the zerofield viscosity, the yield stress, and the leakage current density increase with increasing viscosity of the silicone oils. The effects of the viscosity on the ER efficiency, the shear stability, and the sedimentation ratio depend on the competition between the viscous resistance and the aggregation of the particles. Among the three ER fluids prepared with silicone oil with different terminal groups, hydroxyl-terminated oil based sample has the highest zero-field viscosity, the highest field-induced yield stress and ER efficiency, the largest current density, and the best sedimentation stability.
基金supported by the Key Technologies Research and Development Program of Guangzhou (No.2023B03J1284)Guangdong Yuehai Water Investment Co.,Ltd. (No.CC80-QT01-2020-0010).
文摘This work established a quantitative method to access the shear stability of aerobic granular sludge(AGS)and validated its feasibility by using the mature AGS from a pilot-scale(50 tons/day)membrane bioreactor(MBR)for treating real municipal wastewater.The results showed that the changing rate( S)of the peak area(S)of granule size distribution(GSD)exhibited an exponential relationship(R^(2)≥0.76)with the shear time(y=a−b·c^(x)),which was a suitable indicative index to reflect the shear stability of different AGS samples.The limiting granule size(LGS)was defined and proposed to characterize the equilibrium size for AGS after being sheared for a period of time,whose value in terms of Dv50 showed high correlation(R^(2)=0.92)with the parameter a.The free Ca^(2+)(28.44-34.21 mg/L)in the influent specifically interacted with polysaccharides(PS)in the granule’s extracellular polymeric substance(EPS)as a nucleation site,thereby inducing the formation of Ca precipitation to enhance its Young’s modulus,while Ca^(2+) primarily interacted with PS in soluble metabolic product(SMP)during the initial granulation process.Furthermore,the Young’s modulus significantly affected the parameter a related to shear stability(R^(2)=0.99).Since the parameter a was more closely related(R^(2)=1.00)to S than that of the parameter b or c,the excellent correlation(R^(2)=0.99)between the parameter a and the wet density further verified the feasibility of this method.
基金supported by the Department of Energy Office of Fusion Energy Sciences DE-FG02-04ER54766
文摘In an experimental realization of the sheared cylindrical slab, the level of plasma turbulence is strongly reduced by application of a sufficient bias potential difference in the radial direction. Density fluctuation levels △nrms/n decrease by more than a factor of five. The ion flow velocity profile is measured spectroscopically from the Doppler shift of an argon ion line. Comparison of the shearing rates with the turbulent amplitudes as a function of bias show no relation between the shearing rate and turbulence reduction, contrary to expectations.
基金Supported by the National Natural Science Foundation of China （ 10375018 ）
文摘Internal transport barriers （ITBs） are phenomena associated with improved confinement mode of tokamak plasmas. Within the region where the ITB locates, the plasma pressure has a large gradient while the magnetic shear s has a minimum so that within and near the ITB, the absolute value of the shear is very low. Physics involved is plentiful, from the macroscopic （ MHD ） stability, to the suppression of microscopic instabilities thought to be responsible for anomalous transport. The treatment of very low shear also poses some theoretical difficulties.
基金the Research Partnership to Secure Energy for America (RPSEA)Oklahoma State University Chemical Engineering Department for partial support of this project
文摘Partially hydrolyzed polyacrylamide（HPAM）as the main component of slickwater fracturing fluid is a shear-sensitive polymer,which suffers from mechanical degradation at turbulent flow rates.Five different concentrations of HPAM as well as mixtures of polyacrylamide/xanthan gum were prepared to investigate the possibility of improving shear stability of HPAM.Drag reduction（DR）measurements were performed in a closed flow loop.For HPAM solutions,the extent of DR increased from 30%to67%with increasing HPAM concentration from 100 to1000 wppm.All the HPAM solutions suffered from mechanical degradation and loss of DR efficiency over the shearing period.Results indicated that the resistance to shear degradation increased with increasing polymer concentration.DR efficiency of 600 wppm xanthan gum（XG）was 38%,indicating that XG was not as good a drag reducer as HPAM.But with only 6%DR decline,XG solution exhibited a better shear stability compared to HPAM solutions.Mixed HPAM/XG solutions initially exhibited greater DR（40%and 55%）compared to XG,but due to shear degradation,DR%dropped for HPAM/XG solutions.Compared to 200 wppm HPAM solution,addition of XG did not improve the drag reduction efficiency of HPAM/XG mixed solutions though XG slightly improved the resistance against mechanical degradation in HPAM/XG mixed polymer solutions.
文摘Viscosity index (VI) and shear stability index (SSI) are standard methods used in the lubricant industry to determine temperature-viscosity dependency and resistance to product degradation, respectively. A variety of oil-soluble polymers, including poly(alkyl methacrylates) (PAMAs) are routinely used to control these properties in fully-formulated liquid lubricants. In this report, we use reversible addition-fragmentation chain transfer (RAFT) polymerization to precisely target identical degrees of polymerization in a family of PAMAs with varying lauryl, hexyl, butyl, ethyl, and methyl groups. Then, expanding on previous methodology reported in the literature, we establish structure property relationships for these PAMAs, specifically looking at how intrinsic viscosity [η] and Martin interaction parameters K<sub>M</sub> relate to VI and SSI characteristics. While the intrinsic viscosity [η] is associated with the volume of macromolecules at infinite dilution, the parameter K<sub>M</sub> reflects the hydrodynamic interactions of polymer chains at actual polymer concentrations in lubricating oils. In this paper, we show that the dependence of VI on the non-dimensional concentration c/c* (or c[η]) can be presented in a form of master curve with shift factors proportional to K<sub>M</sub> that decreases with increasing size of alkyl groups. This finding implies that even in the dilute regime, the coil-expansion theory used to explain the effect of macromolecules on VI should be complemented with the idea of hydrodynamic interactions between polymer molecules that can be controlled by the choice of alkyl chains in the family of PAMAs.
文摘In this paper, four kinds of polymethacrylates(PMAs) used as multifunctional additives were synthesized from quaternary C1—C14 methacrylate, among which sample 4 exhibited relatively better performance. According to the methacrylate ratio of sample 4, the optimized reaction conditions of PMA were explored by orthogonal experiments comprising 4 factors and 3 levels, and the optimized reaction conditions covered an initiator dosage of 0.8 %, a molecular weight regulator dosage of 0.4%, a reaction temperature of 95 ℃ and a reaction time of 8.5 h. When the optimized PMA samples were used to formulate the 75W/90 automotive gear base oil, they exhibited improved shear stability and good low temperature property. In comparison with foreign commercial polymethacrylate GP, the optimized PMA samples exhibited better thickening ability, similar shear stability and slightly weak low temperature property, with their performance being the same as GP's on the whole. The slight difference in the performance between the optimized PMA and GP was attributed to the difference of chain length of copolymers and the distribution of relative molecular mass between them.
基金supported by the National Key Research and Development Plan(2018YFA0703603)Guangdong Major Project of Basic and Applied Basic Research,China(2019B030302010)+1 种基金the National Natural Science Foundation of China(51822107,11790291 and 61888102)the Strategic Priority Research Program of Chinese Academy of Sciences(XDB30000000)。
文摘Ir-Ni-Ta metallic glasses(MGs)exhibit an array of superior high-temperature properties,making them attractive for applications at high temperatures or in harsh environments.However,Ir-Ni-Ta bulk MGs are quite brittle and often fracture catastrophically even before plastic yielding,significantly undercutting their high-strength advantage.Here,we show that the Ir-Ni-Ta MGs are not intrinsically brittle,but rather malleable when the feature size is reduced to micro/nano-scales.All tested Ir-Ni-Ta MG micropillars with a diameter ranging from~500 nm to~5μm display a large plastic strain above 25%(the maximum up to 35%),together with a yield strength up to 7 GPa,well exceeding the strength recorded in most metallic materials.The intrinsic shear stability of Ir-Ni-Ta MGs,as characterized by the normalized shear displacement during a shear event,is much larger than those malleable Zr-and Cu-based MGs.Our results suggest that Ir-Ni-Ta MGs are excellent candidates for micro/nanoscale structural applications used at high-temperature or extreme conditions.
基金supported by the National Natural Science Foundation of China (No. 51476152)
文摘The linear instabilities of incompressible confluent mixing layer and boundary layer were analyzed.The mixing layers include wake,shear layer and their combination.The mean velocity profile of confluent flow is taken as a superposition of a hyperbolic and exponential function to model a mixing layer and the Blasius similarity solution for a flat plate boundary layer.The stability equation of confluent flow was solved by using the global numerical method.The unstable modes associated with both the mixing and boundary layers were identified.They are the boundary layer mode,mixing layer mode 1（nearly symmetrical mode）and mode 2（nearly anti-symmetrical mode）.The interactions between the mixing layer stability and the boundary layer stability were examined.As the mixing layer approaches the boundary layer,the neutral curves of the boundary layer mode move to the upper left,the resulting critical Reynolds number decreases,and the growth rate of the most unstable mode increases.The wall tends to stabilize the mixing layer modes at low frequency.In addition,the mode switching behavior of the relative level of the spatial growth rate between the mixing layer mode 1 and mode 2 with the velocity ratio is found to occur at low frequency.
