The effects of initial microstructure on the flow stress, strain rate sensitivity （m）, strain hardening exponent （n）, apparent activation energy （Q） for deformation of Ti-5Al-2Sn-2Zr-4Mo-4Cr alloy were investiga...The effects of initial microstructure on the flow stress, strain rate sensitivity （m）, strain hardening exponent （n）, apparent activation energy （Q） for deformation of Ti-5Al-2Sn-2Zr-4Mo-4Cr alloy were investigated using isothermal compression tests. Results show that the alloy with Widmanst-tten alpha plates shows a higher peak stress and flow softening. Additionally, the alloy with equiaxed primary alpha exhibits an early yield drop at or above 810 ℃ and at strain rates of 0.1-5.0 s^-1. In the strain range of 0.5-0.7,m of the alloy with equiaxed primary alpha is found to be larger at 0.01 s^-1 and lower deformation temperatures. This phenomenon could be reasonably explained based on the microstructure evolution. The strain has a significant effect onn of the alloy with Widmanst-tten alpha plates, which is attributed to platelet bending/kinking and dynamic globularization ofα phase. In the strain range of 0.15-0.55,Q of the alloy with Widmanst-tten alpha plates is larger.展开更多
The effects of heat treatment parameters on the microstructure,and mechanical properties and fractured morphology of Ti-5Al-2Sn-2Zr-4Mo-4Cr with the equiaxed,bi-modal and Widmanst？tten microstructures were investigat...The effects of heat treatment parameters on the microstructure,and mechanical properties and fractured morphology of Ti-5Al-2Sn-2Zr-4Mo-4Cr with the equiaxed,bi-modal and Widmanst？tten microstructures were investigated.The heating temperatures for obtaining the equiaxed,bi-modal and Widmanst？tten microstructures were 830,890 and 920 °C,respectively,followed by furnace cooling at a holding time of 30 min.The volume fraction of primary α phase decreased with increasing the heating temperature,which was 45.8% at 830 °C,and decreased to 15.5% at 890 °C,and then the primary α phase disappeared at 920 °C during furnace cooling.The variation of volume fraction of primary α phase in air cooling is similar to that in furnace cooling.The increase in heating temperature and furnace cooling benefited the precipitation and growth of the secondary α phase.The equiaxed microstructure exhibited excellent mechanical properties,in which the ultimate strength,yield strength,elongation and reduction in area were 1035 MPa,1011 MPa,20.8% and 58.7%,respectively.The yield strength and elongation for the bi-modal microstructure were slightly lower than those of the equiaxed microstructure.The Widmanst？tten microstructure exhibited poor ductility and low yield strength,while the ultimate strength reached 1078 MPa.The dimple fractured mechanism for the equiaxed and bi-modal microstructures proved excellent ductility.The coexistence of dimple and intercrystalline fractured mechanisms for the Widmanst？tten microstructure resulted in the poor ductility.展开更多
基金Projects(5120531851275416)supported by the National Natural Science Foundation of ChinaProject(2012KJ02002)supported by the Innovation Fund of Science and Technology in Northwestern Polytechnical University,China
文摘The effects of initial microstructure on the flow stress, strain rate sensitivity （m）, strain hardening exponent （n）, apparent activation energy （Q） for deformation of Ti-5Al-2Sn-2Zr-4Mo-4Cr alloy were investigated using isothermal compression tests. Results show that the alloy with Widmanst-tten alpha plates shows a higher peak stress and flow softening. Additionally, the alloy with equiaxed primary alpha exhibits an early yield drop at or above 810 ℃ and at strain rates of 0.1-5.0 s^-1. In the strain range of 0.5-0.7,m of the alloy with equiaxed primary alpha is found to be larger at 0.01 s^-1 and lower deformation temperatures. This phenomenon could be reasonably explained based on the microstructure evolution. The strain has a significant effect onn of the alloy with Widmanst-tten alpha plates, which is attributed to platelet bending/kinking and dynamic globularization ofα phase. In the strain range of 0.15-0.55,Q of the alloy with Widmanst-tten alpha plates is larger.
基金Projects(51205318,51275416)supported by the National Natural Science Foundation of ChinaProject(3102014JCQ01016)supported by the Fundamental Research Funds for the Central Universities,China
文摘The effects of heat treatment parameters on the microstructure,and mechanical properties and fractured morphology of Ti-5Al-2Sn-2Zr-4Mo-4Cr with the equiaxed,bi-modal and Widmanst？tten microstructures were investigated.The heating temperatures for obtaining the equiaxed,bi-modal and Widmanst？tten microstructures were 830,890 and 920 °C,respectively,followed by furnace cooling at a holding time of 30 min.The volume fraction of primary α phase decreased with increasing the heating temperature,which was 45.8% at 830 °C,and decreased to 15.5% at 890 °C,and then the primary α phase disappeared at 920 °C during furnace cooling.The variation of volume fraction of primary α phase in air cooling is similar to that in furnace cooling.The increase in heating temperature and furnace cooling benefited the precipitation and growth of the secondary α phase.The equiaxed microstructure exhibited excellent mechanical properties,in which the ultimate strength,yield strength,elongation and reduction in area were 1035 MPa,1011 MPa,20.8% and 58.7%,respectively.The yield strength and elongation for the bi-modal microstructure were slightly lower than those of the equiaxed microstructure.The Widmanst？tten microstructure exhibited poor ductility and low yield strength,while the ultimate strength reached 1078 MPa.The dimple fractured mechanism for the equiaxed and bi-modal microstructures proved excellent ductility.The coexistence of dimple and intercrystalline fractured mechanisms for the Widmanst？tten microstructure resulted in the poor ductility.
