One of the most effective methods for sand control is the chemical consolidation of sandstone structures.In this paper,the impacts of crude oil and brine in the static state and the impact of the flow rates of the flu...One of the most effective methods for sand control is the chemical consolidation of sandstone structures.In this paper,the impacts of crude oil and brine in the static state and the impact of the flow rates of the fluids in the dynamic state have been assessed at the reservoir conditions.The analyses in this research were Young’s modulus,compressive strength,porosity,and permeability which were done on core samples after and before fluid contact.Samples made with two different resins showed good resistance to crude oil in both states.No considerable change was seen in the analyses even at high crude oil injection rates in the dynamic state.Conversely,brine caused a noticeable change in the analyses in both states.In the presence of brine at the static state,Young’s modulus and compressive strength respectively decreased by 37.5%and 34.5%for epoxy cores,whereas these parameters respectively reduced by 30%and 41%for furan cores.In brine presence at the dynamic state,compressive strength reduction was 10.28 MPa for furan and 6.28 MPa for epoxy samples and their compressive strength reached 16.75 MPa and 26.54 MPa respectively which are higher than the critical point to be known as weak sandstone core.Moreover,Young’s modulus decrease values for furan and epoxy samples were respectively 0.37 GPa and 0.44 GPa.Therefore,brine had a more destructive effect on the mechanical characteristics of samples in the static state than the dynamic one for two resins.In addition,brine injection increased permeability by about 13.6%for furan and 34.8%for epoxy.Also,porosity raised by about 21.8%for furan,and 19%for epoxy by brine injection.The results showed that the chemical sand consolidation weakens in the face of brine production along with crude oil which can lead to increasing cost of oil production and treating wellbore again.展开更多
Carbonated water injection(CWI)is known as an efficient technique for both CO2 storage and enhanced oil recovery(EOR).During CWI process,CO2 moves from the water phase into the oil phase and results in oil swelling.Th...Carbonated water injection(CWI)is known as an efficient technique for both CO2 storage and enhanced oil recovery(EOR).During CWI process,CO2 moves from the water phase into the oil phase and results in oil swelling.This mechanism is considered as a reason for EOR.Viscous fingering leading to early breakthrough and leaving a large proportion of reservoir un-swept is known as an unfavorable phenomenon during flooding trials.Generally,instability at the interface due to disturbances in porous medium promotes viscous fingering phenomenon.Connate water makes viscous fingers longer and more irregular consisting of large number of tributaries leading to the ultimate oil recovery reduction.Therefore,higher in-situ water content can worsen this condition.Besides,this water can play as a barrier between oil and gas phases and adversely affect the gas diffusion,which results in EOR reduction.On the other hand,from gas storage point of view,it should be noted that CO2 solubility is not the same in the water and oil phases.In this study for a specified water salinity,the effects of different connate water saturations(Swc)on the ultimate oil recovery and CO2 storage capacity during secondary CWI are being presented using carbonate rock samples from one of Iranian carbonate oil reservoir.The results showed higher oil recovery and CO2 storage in the case of lower connate water saturation,as 14%reduction of Swc resulted in 20%and 16%higher oil recovery and CO2 storage capacity,respectively.展开更多
It is necessary to understand all the prerequisites, which result in gas hydrate formation for safe design and control of a variety of processes in petroleum industry. Thermodynamic hydrate inhibitors (THIs) are norma...It is necessary to understand all the prerequisites, which result in gas hydrate formation for safe design and control of a variety of processes in petroleum industry. Thermodynamic hydrate inhibitors (THIs) are normally used to preclude gas hydrate formation by shifting hydrate stability region to lower temperatures and higher pressures. Sometimes, it is difficult to avoid hydrate formation and hydrates will form anyway. In this situation, kinetic hydrate inhibitors (KHIs) can be used to postpone formation of gas hydrates by retarding hydrate nucleation and growth rate. In this study, two kinetic parameters including natural gas hydrate formation induction time and the rate of gas consumption were experimentally investigated in the presence of monoethylene glycol (MEG), L-tyrosine, and polyvinylpyrrolidone (PVP) at various concentrations in aqueous solutions. Since hydrate formation is a stochastic phenomenon, the repeatability of each kinetic parameter was evaluated several times and the average values for the hydrate formation induction times and the rates of gas consumption are reported. The results indicate that from the view point of hydrate formation induction time, 2 wt% PVP and 20 wt% MEG aqueous solutions have the highest values and are the best choices. It is also interpreted from the results that from the view point of the rate of gas consumption, 20 wt% MEG aqueous solution yields the lowest value and is the best choice. Finally, it is concluded that the combination of PVP and MEG in an aqueous solution has a simultaneous synergistic impact on natural gas hydrate formation induction time and the rate of gas consumption. Furthermore, a semi-empirical model based on chemical kinetic theory is applied to evaluate the hydrate formation induction time data. A good agreement between the experimental and calculated hydrate formation induction time data is observed.展开更多
In this way, after experimental measurement of interfacial tension, different models including mono-exponential decay, dynamic adsorption models and empirical equation are used to correlate this time-dependent behavio...In this way, after experimental measurement of interfacial tension, different models including mono-exponential decay, dynamic adsorption models and empirical equation are used to correlate this time-dependent behavior of interfacial tension(IFT). During the modeling approach, the induction, adsorption, equilibrium, and mesoequilibrium times as well as diffusivity of surface active components known as natural surfactant including asphaltene and resin from crude oil to the interface are obtained. In addition, the surface excess concentration of surface active components at the interface and Gibbs adsorption isotherm are utilized to analyze the measured dynamic IFTs. Finally, the mechanisms of crude oil/aqueous solution IFT including(a) the activity of surfaceactive components and(b) surface excess concentration of them at fluid/fluid interface are proposed and discussed in details.展开更多
Despite many efforts into the study of fluids interaction in low salinity water flooding, they are not probing the basics of transport phenomena between the involved phases. This work is aimed to bring new understandi...Despite many efforts into the study of fluids interaction in low salinity water flooding, they are not probing the basics of transport phenomena between the involved phases. This work is aimed to bring new understanding of fluid-fluid interaction during low salinity water flooding through a series of organized experiments in which a crude oil sample with known properties was kept in contact with different brine solutions of various ionic strengths. Measuring brine pH, conductivity and crude oil viscosity and density for a period of 45 days illustrates the strong effect of the contact time and ionic strength on the dissociation of polar components and physical properties of the crude oil and brine. Besides, the interfacial tension(IFT) measurements show that the interfacial interactions are affected by several competitive interfacial processes. By decreasing the ionic strength of the brine, the solubility of naphthenic acids in the aqueous solution increases, and hence,the conductivity and the pH of the aqueous phase decrease. To verify this important finding, UV-Vis spectroscopy and 'H NMR analysis were also performed on aged brine samples. Notably, there is an ionic strength of brine in which the lowest IFT is observed, while the other physical properties are remained relatively unchanged.展开更多
Understanding the roles of asphaltene and resin as natural surfactants existed in crude oil can enlighten contradicting reported results regarding interfacial tension(IFT) of crude oil/aqueous solution as a function o...Understanding the roles of asphaltene and resin as natural surfactants existed in crude oil can enlighten contradicting reported results regarding interfacial tension(IFT) of crude oil/aqueous solution as a function of salinity and ion type. In this way, this study is aimed to investigate the effect of these natural surface active agents on IFT of with special focus on SO4^2-anion and Mg^2+cation. Two different synthetic oil solutions of 8 wt% of the extracted asphaltene and resin dissolved in toluene are prepared, and then IFT values are measured. After that,the obtained results are compared with the IFT of intact crude oil in contact with the same saline solutions examined in the previous stage. The obtained results showed a synergistic effect of Na2SO4+ MgCl2 solution unlike the MgSO4+ MgCl2 and CaSO4+ MgCl2 solutions on IFT reduction of resin at MgCl2 concentration of 15000 mg·kg^-1. In summary, it is found that the affinity of asphaltene molecules towards the interface of oleic phase/ionic solution leads to higher IFT variation.展开更多
Nanofluids because of their surface characteristics improve the oil production from reservoirs by enabling different enhanced recovery mechanisms such as wettability alteration,interfacial tension(IFT)reduction,oil vi...Nanofluids because of their surface characteristics improve the oil production from reservoirs by enabling different enhanced recovery mechanisms such as wettability alteration,interfacial tension(IFT)reduction,oil viscosity reduction,formation and stabilization of colloidal systems and the decrease in the asphaltene precipitation.To the best of the authors’ knowledge,the synthesis of a new nanocomposite has been studied in this paper for the first time.It consists of nanoparticles of both SiO2 and Fe3O4.Each nanoparticle has its individual surface property and has its distinct effect on the oil production of reservoirs.According to the previous studies,Fe3O4 has been used in the prevention or reduction of asphaltene precipitation and SiO2 has been considered for wettability alteration and/or reducing IFTs in enhanced oil recovery.According to the experimental results,the novel synthesized nanoparticles have increased the oil recovery by the synergistic effects of the formed particles markedly by activating the various mechanisms relative to the use of each of the nanoparticles in the micromodel individually.According to the results obtained for the use of this nanocomposite,understanding reservoir conditions plays an important role in the ultimate goal of enhancing oil recovery and the formation of stable emulsions plays an important role in oil recovery using this method.展开更多
This study investigates the effect of injecting nanofluids containing nano-SiO_2 as drag reducing agents(DRA) at different concentrations on the pressure drop of air-water flow through horizontal pipe.The test fluid u...This study investigates the effect of injecting nanofluids containing nano-SiO_2 as drag reducing agents(DRA) at different concentrations on the pressure drop of air-water flow through horizontal pipe.The test fluid used in this study was air-water with nano-SiO_2 particles at 0.1%-1%mass concentration.The test sections of the experimental set-up were five pipes of the same length of 9 m with ID from 0.0127m-0.03175m(0.5 to 1.25 in).Airwater flow was run in slug flow regime under different volumetric flow rates.The results of drag reduction(η%)indicated that the addition of DRA could be efficient up to some dosage.Drag reduction performed much better for smaller pipe diameters than it did for larger ones.For various nanosilica concentrations,the maximum drag reduction was about 66.8%for 0.75%mass concentration of nanosilica.展开更多
The e ects of CO2 and salt type on the interfacial tension(IFT) between crude oil and carbonated brine(CB) have not been fully understood. This study focuses on measuring the dynamic IFT between acidic crude oil with ...The e ects of CO2 and salt type on the interfacial tension(IFT) between crude oil and carbonated brine(CB) have not been fully understood. This study focuses on measuring the dynamic IFT between acidic crude oil with a total acid number of 1.5 mg KOH/g and fully CO2-saturated aqueous solutions consisting of 15,000 ppm of KCl, NaCl, CaCl2 and MgCl2 at 30 °C and a wide range of pressures(500–4000 psi). The results of IFT measurements showed that solvation of CO2 into all the studied aqueous solutions led to an increase in IFT of acidic crude oil(i.e., comparison of IFT of crude oil/CB and crude oil/brine), while no significant e ect was observed for pressure. In contrast, the obtained results of studied salts indicated a positive e ect on the IFT reduction of acidic crude oil/carbonated water(CW)(i.e., comparison of IFT of crude oil/CB and crude oil/CW).展开更多
For syngas production, the combustion of fossil fuels produces large amounts of CO2 as a greenhouse gas annually which intensifies global warming. In this study, chemical looping combustion （CLC） has been utilized f...For syngas production, the combustion of fossil fuels produces large amounts of CO2 as a greenhouse gas annually which intensifies global warming. In this study, chemical looping combustion （CLC） has been utilized for the elimination of CO2 emission to atmosphere during simultaneous syngas production with different H2/CO ratio in steam reforming of methane （SR） and dry reforming of methane （DR） in a CLC-SR-DR configuration. In CLC-SR-DR with 184 reformer tubes （similar to an industrial scale steam reformer in Zagros Petrochemical Company, Assaluyeh, Iran）, DR reaction occurs over Rh-based catalysts in 31 tubes. Also, SR reaction is happened over Ni-based catalysts in 153 tubes. CLC via employment of Mn-based oxygen carriers supplies heat for DR and SR reactions and produces CO2 and H2O as raw materials simultaneously. A steady state heterogeneous catalytic reaction model is applied to analyze the performance and applicability of the proposed CLC-SR-DR configuration. Simulation results show that combustion efficiency reached 1 at the outlet of fuel reactor （FR）. Therefore, pure CO2 and H2O can be recycled to DR and SR sides, respectively. Also, CH4 conversion reached 0.2803 and 0.7275 at the outlet of SR and DR sides, respectively. Simulation results indicate that, 3223 kmol.h-l syngas with a H2/CO ratio equal to 9.826 was produced in SR side of CLC-SR-DR. After that, 1844 kmol.h-1 syngas with a H2/CO ratio equal to 0.986 was achieved in DR side of CLC-SR-DR. Results illustrate that by increasing the number of DR tubes to 50 tubes and considering 184 fixed total tubes in CLC-SR-DR, CH4 conversions in SR and DR sides decreased 2.69% and 3.31%, respectively. However, this subject caused total syngas production in SR and DR sides （in all of 184 tubes） enhance to 5427 kmol-h-1. Finally, thermal and molar behaviors of the proposed configuration demonstrate that CLC-SR-DR is applicable for simultaneous syngas production with high and low Hx/CO ratios in an environmental friendly process.展开更多
In this study,the impacts of solutal Marangoni phenomenon on multiphase flow in static and micromodel geometries have experimentally been studied and the interactions between oil droplet and two different alkaline sol...In this study,the impacts of solutal Marangoni phenomenon on multiphase flow in static and micromodel geometries have experimentally been studied and the interactions between oil droplet and two different alkaline solutions(i.e.MgS04 and Na_2 CO_3) were investigated.The static tests revealed that the Marangoni convection exists in the presence of the alkaline and oil which should carefully be considered in porous media.In the micromodel experiments,observations showed that in the MgS04 flooding,the fluids stayed almost stationary,while in the Na2 C03 flooding,a spontaneous movement was detected.The changes in the distribution of fluids showed that the circular movement of fluids due to the Marangoni effects can be effective in draining of the unswept regions.The dimensional analysis for possible mechanisms showed that the viscous,gravity and diffusion forces were negligible and the other mechanisms such as capillary and Marangoni effects should be considered in the investigated experiments.The value of the new defined Marangoni/capillary dimensionless number for the Na2 C03 solution was orders of magnitude larger than the MgS04 flooding scenario which explains the differences between the two cases and also between different micromodel regions.In conclusion,the Marangoni convection is activated by creating an ultra-low IFT condition in multiphase flow problems that can be profoundly effective in increasing the phase mixing and microscopic efficiency.展开更多
In this investigation, a novel thermally coupled reactor （TCR） containing methyl formate （MF） production in the endothermic side and methanol synthesis in the exothermic side has been investigated. The interesting...In this investigation, a novel thermally coupled reactor （TCR） containing methyl formate （MF） production in the endothermic side and methanol synthesis in the exothermic side has been investigated. The interesting feature of this TCR is that productive methanol in the exothermic side could be recycled and used as feed of endothermic side for MF synthesis. Other important advantages of the proposed system are high production rates of hydrogen and MF. The configuration consists of two thermally coupled concentric tubular reactors. In these coupled reactors, autothermal system is obtained within the reactor. A steady-state heterogeneous model is used for simulation of the coupled reactor. The proposed model has been utilized to compare the performance of TCR with the conventional methanol reactor （CMR）. Noticeable enhancement can be obtained in the performance of the reactors. The influence of operational parameters is studied on reactor performance. The results show that coupling of these reactions could be feasible and beneficial. Experimental proof-of-concept is required to validate the operation of the novel reactor.展开更多
Unwanted water production together with oil and gas production is a striking problem in oil and gas industries, and many approaches have been examined to overcome this major problem. Preformed particle gels (PPGs) sho...Unwanted water production together with oil and gas production is a striking problem in oil and gas industries, and many approaches have been examined to overcome this major problem. Preformed particle gels (PPGs) showed dramatically good properties for this purpose in mature oil and gas reservoirs. In this study, we carefully synthesized an efficient series of PPGs with using a design of experiments (DOE) software. Acrylamide (AAm)/Acrylic acid (AA) mole ratio, N,N’-methylenebisacrylamide (MBA) mole percentage and swelling time were considered as key parameters to examine PPG swelling behavior. Our results presented a detailed empirical correlation, which could significantly predict the swelling capacity of PPGs in CaCl2 salt solution (200,000 ppm).展开更多
Most fractured carbonate oil reservoirs have oil-wet rocks.Therefore,the process of imbibing water from the fractures into the matrix is usually poor or basically does not exist due to negative capillary pressure.To a...Most fractured carbonate oil reservoirs have oil-wet rocks.Therefore,the process of imbibing water from the fractures into the matrix is usually poor or basically does not exist due to negative capillary pressure.To achieve appropriate ultimate oil recovery in these reservoirs,a water-based enhanced oil recovery method must be capable of altering the wettability of matrix blocks.Previous studies showed that carbonated water can alter wettability of carbonate oil-wet rocks toward less oil-wet or neutral wettability conditions,but the degree of modification is not high enough to allow water to imbibe spontaneously into the matrix blocks at an effective rate.In this study,we manipulated carbonated brine chemistry to enhance its wettability alteration features and hence to improve water imbibition rate and ultimate oil recovery upon spontaneous imbibition in dolomite rocks.First,the contact angle and interfacial tension(IFT)of brine/crude oil systems were measured for several synthetic brine samples with different compositions.Thereafter,two solutions with a significant difference in WAI(wettability alteration index)but approximately equal brine/oil IFT were chosen for spontaneous imbibition experiments.In the next step,spontaneous imbibition experiments at ambient and high pressures were conducted to evaluate the ability of carbonated smart water in enhancing the spontaneous imbibition rate and ultimate oil recovery in dolomite rocks.Experimental results showed that an appropriate adjustment of the imbibition brine(i.e.,carbonated smart water)chemistry improves imbibition rate of carbonated water in oil-wet dolomite rocks as well as the ultimate oil recovery.展开更多
Viscous fingering is one of the main challenges that could reduce areal sweep efficiency during waterflooding in oil reservoirs. A series of waterflooding experiments were carried out in a Hele-Shaw cell at ambient te...Viscous fingering is one of the main challenges that could reduce areal sweep efficiency during waterflooding in oil reservoirs. A series of waterflooding experiments were carried out in a Hele-Shaw cell at ambient temperature during which areal sweep efficiency was estimated and techniques to ease the fingering problem were examined. The onset and propagation of viscous fingers were monitored as a function of both injection rate and injection/production positions. Image processing techniques were utilized to quantitatively investigate the propagation of fingers. The experimental results show that, under specific conditions, increasing the number of finger branches could improve the areal sweep efficiency, whereas growth of a single narrow finger has a negative impact on oil displacement efficiency. According to the obtained results,increasing the injection rate improves the areal sweep efficiency up to a critical rate at which viscous fingers start to grow.The impact of heterogeneity of the medium on distributing the viscous fingers was also investigated by introducing two different arrangements of fractures in the model. The results show that fractures perpendicular to the direction of flow would distribute the displacing water more uniformly, while fractures in the direction of flow would amplify the unfavorable sweep efficiency.展开更多
Composition estimation plays very important role in plant operation and control.Extended Kalman filter(EKF) is one of the most common estimators,which has been used in composition estimation of reactive batch distilla...Composition estimation plays very important role in plant operation and control.Extended Kalman filter(EKF) is one of the most common estimators,which has been used in composition estimation of reactive batch distillation,but its performance is heavily dependent on the thermodynamic modeling of vapor-liquid equilibrium,which is difficult to initialize and tune.In this paper an inferential state estimation scheme based on adaptive neuro-fuzzy inference system(ANFIS) ,which is a model base estimator,is employed for composition estimation by using temperature measurements in multicomponent reactive batch distillation.The state estimator is supported by data from a complete dynamic model that includes component and energy balance equations accompanied with thermodynamic relations and reaction kinetics.The mathematical model is verified by pilot plant data.The simulation results show that the ANFIS estimator provides reliable and accurate estimation for component concentrations in reactive batch distillation.The estimated states form a basis for improving the performance of reactive batch distillation either through decision making of an operator or through an automatic closed-loop control scheme.展开更多
For improvement of vanadium redox flow battery （VRB） performance, novel amphoteric semi- interpenetrating membranes （ASIPN） were prepared using poly（ether ether ketone） （PEEK） and polysul- fone （PSf）, the fo...For improvement of vanadium redox flow battery （VRB） performance, novel amphoteric semi- interpenetrating membranes （ASIPN） were prepared using poly（ether ether ketone） （PEEK） and polysul- fone （PSf）, the former bearing sulfonic groups and the latter imidazolium. These two groups form ionic crosslinks between PEEK and PSf; meanwhile, covalent cross links were built between PSf chains with ad- dition of N-（3-aminopropyl）-imidazole. The amphoteric nature of the membrane allows facile proton and anion transport; the IPN structure and the presence of imidazolium cation effectively suppress vanadium ion crossover through the membrane. Therefore, the ASIPN based VRBs show higher Coulombic efficiency and energy efficiency than that assembled with pristine SPEEK and Nation 212 membranes. Our work demonstrates that the ASIPN membranes are promising for VRB applications.展开更多
Encouraged by the wide spectrum of novel applications of gas hydrates,e.g.,energy recovery,gas separation,gas storage,gas transportation,water desalination,and hydrogen hydrate as a green energy resource,as well as CO...Encouraged by the wide spectrum of novel applications of gas hydrates,e.g.,energy recovery,gas separation,gas storage,gas transportation,water desalination,and hydrogen hydrate as a green energy resource,as well as CO2 capturing,many scientists have focused their attention on investigating this important phenomenon.Of course,from an engineering viewpoint,the mathematical modeling of gas hydrates is of paramount importance,as anticipation of gas hydrate stability conditions is effective in the design and control of industrial processes.Overall,the thermodynamic modeling of gas hydrate can be tackled as an equilibration of three phases,i.e.,liquid,gas,and solid hydrate.The inseparable component in all hydrate systems,water,is highly polar and non-ideal,necessitating the use of more advanced equation of states(EoSs) that take into account more intermolecular forces for thermodynamic modeling of these systems.Motivated by the ever-increasing number of publications on this topic,this study aims to review the application of associating EoSs for the thermodynamic modeling of gas hydrates.Three most important hydrate-based models available in the literature including the van der Waals-Platteeuw(vdW-P) model,Chen-Guo model,and Klauda-Sandler model coupled with and SAFT EoSs were investigated and compared with cubic EoSs.It was concluded that the CPA and SAFT EoSs gave very accurate results for hydrate systems as they take into account the association interactions,which are very crucial in gas hydrate systems in which water,methanol,glycols,and other types of associating compounds are available.Moreover,it was concluded that the CPA EoS is easier to use than the SAFT-type EoSs and our suggestion for the gas hydrate systems is the CPA EoS.展开更多
Foam injection is a promising solution for control of mobility in oil and gas field exploration and development,including enhanced oil recovery,matrix-acidization treatments,contaminated-aquifer remediation and gas le...Foam injection is a promising solution for control of mobility in oil and gas field exploration and development,including enhanced oil recovery,matrix-acidization treatments,contaminated-aquifer remediation and gas leakage prevention.This study presents a numerical investigation of foam behavior in a porous medium.Fractional flow method is applied to describe steady-state foam displacement in the entrance region.In this model,foam flow for the cases of excluding and including capillary pressure and for two types of gas,nitrogen(N2)and carbon dioxide(CO2)are investigated.Effects of pertinent parameters are also verified.Results indicate that the foam texture strongly governs foam flow in porous media.Required entrance region may be quite different for foam texture to accede local equilibrium,depending on the case and physical properties that are used.According to the fact that the aim of foaming of injected gas is to reduce gas mobility,results show that CO2 is a more proper injecting gas than N2.There are also some ideas presented here on improvement in foam displacement process.This study will provide an insight into future laboratory research and development of full-field foam flow in a porous medium.展开更多
In this study, radial flow moving bed reactors for isobutane dehydrogenation have been modeled and simulated heterogeneously based on mass and energy conservation laws. The considered reaction networks in the model ar...In this study, radial flow moving bed reactors for isobutane dehydrogenation have been modeled and simulated heterogeneously based on mass and energy conservation laws. The considered reaction networks in the model are isobutene dehydrogenation as main reaction, and hydrogenolysis, propane dehydrogenation as well as coke formation as side reactions that all occur on the catalyst surface. Then, the process condition has been optimized to produce more isobutene under steady state condition. To prove the accuracy of the considered mathematical model and assumptions, simulation results are compared with the plant data. As a powerful method in the global optimization, the genetic algorithm has been used to optimize the considered objective function. The isobutane conversion and isobutene selectivity under optimal conditions are about 40.1% and 91%, respectively.展开更多
文摘One of the most effective methods for sand control is the chemical consolidation of sandstone structures.In this paper,the impacts of crude oil and brine in the static state and the impact of the flow rates of the fluids in the dynamic state have been assessed at the reservoir conditions.The analyses in this research were Young’s modulus,compressive strength,porosity,and permeability which were done on core samples after and before fluid contact.Samples made with two different resins showed good resistance to crude oil in both states.No considerable change was seen in the analyses even at high crude oil injection rates in the dynamic state.Conversely,brine caused a noticeable change in the analyses in both states.In the presence of brine at the static state,Young’s modulus and compressive strength respectively decreased by 37.5%and 34.5%for epoxy cores,whereas these parameters respectively reduced by 30%and 41%for furan cores.In brine presence at the dynamic state,compressive strength reduction was 10.28 MPa for furan and 6.28 MPa for epoxy samples and their compressive strength reached 16.75 MPa and 26.54 MPa respectively which are higher than the critical point to be known as weak sandstone core.Moreover,Young’s modulus decrease values for furan and epoxy samples were respectively 0.37 GPa and 0.44 GPa.Therefore,brine had a more destructive effect on the mechanical characteristics of samples in the static state than the dynamic one for two resins.In addition,brine injection increased permeability by about 13.6%for furan and 34.8%for epoxy.Also,porosity raised by about 21.8%for furan,and 19%for epoxy by brine injection.The results showed that the chemical sand consolidation weakens in the face of brine production along with crude oil which can lead to increasing cost of oil production and treating wellbore again.
文摘Carbonated water injection(CWI)is known as an efficient technique for both CO2 storage and enhanced oil recovery(EOR).During CWI process,CO2 moves from the water phase into the oil phase and results in oil swelling.This mechanism is considered as a reason for EOR.Viscous fingering leading to early breakthrough and leaving a large proportion of reservoir un-swept is known as an unfavorable phenomenon during flooding trials.Generally,instability at the interface due to disturbances in porous medium promotes viscous fingering phenomenon.Connate water makes viscous fingers longer and more irregular consisting of large number of tributaries leading to the ultimate oil recovery reduction.Therefore,higher in-situ water content can worsen this condition.Besides,this water can play as a barrier between oil and gas phases and adversely affect the gas diffusion,which results in EOR reduction.On the other hand,from gas storage point of view,it should be noted that CO2 solubility is not the same in the water and oil phases.In this study for a specified water salinity,the effects of different connate water saturations(Swc)on the ultimate oil recovery and CO2 storage capacity during secondary CWI are being presented using carbonate rock samples from one of Iranian carbonate oil reservoir.The results showed higher oil recovery and CO2 storage in the case of lower connate water saturation,as 14%reduction of Swc resulted in 20%and 16%higher oil recovery and CO2 storage capacity,respectively.
文摘It is necessary to understand all the prerequisites, which result in gas hydrate formation for safe design and control of a variety of processes in petroleum industry. Thermodynamic hydrate inhibitors (THIs) are normally used to preclude gas hydrate formation by shifting hydrate stability region to lower temperatures and higher pressures. Sometimes, it is difficult to avoid hydrate formation and hydrates will form anyway. In this situation, kinetic hydrate inhibitors (KHIs) can be used to postpone formation of gas hydrates by retarding hydrate nucleation and growth rate. In this study, two kinetic parameters including natural gas hydrate formation induction time and the rate of gas consumption were experimentally investigated in the presence of monoethylene glycol (MEG), L-tyrosine, and polyvinylpyrrolidone (PVP) at various concentrations in aqueous solutions. Since hydrate formation is a stochastic phenomenon, the repeatability of each kinetic parameter was evaluated several times and the average values for the hydrate formation induction times and the rates of gas consumption are reported. The results indicate that from the view point of hydrate formation induction time, 2 wt% PVP and 20 wt% MEG aqueous solutions have the highest values and are the best choices. It is also interpreted from the results that from the view point of the rate of gas consumption, 20 wt% MEG aqueous solution yields the lowest value and is the best choice. Finally, it is concluded that the combination of PVP and MEG in an aqueous solution has a simultaneous synergistic impact on natural gas hydrate formation induction time and the rate of gas consumption. Furthermore, a semi-empirical model based on chemical kinetic theory is applied to evaluate the hydrate formation induction time data. A good agreement between the experimental and calculated hydrate formation induction time data is observed.
文摘In this way, after experimental measurement of interfacial tension, different models including mono-exponential decay, dynamic adsorption models and empirical equation are used to correlate this time-dependent behavior of interfacial tension(IFT). During the modeling approach, the induction, adsorption, equilibrium, and mesoequilibrium times as well as diffusivity of surface active components known as natural surfactant including asphaltene and resin from crude oil to the interface are obtained. In addition, the surface excess concentration of surface active components at the interface and Gibbs adsorption isotherm are utilized to analyze the measured dynamic IFTs. Finally, the mechanisms of crude oil/aqueous solution IFT including(a) the activity of surfaceactive components and(b) surface excess concentration of them at fluid/fluid interface are proposed and discussed in details.
基金supported by Iranian Offshore Oil Company (IOOC)
文摘Despite many efforts into the study of fluids interaction in low salinity water flooding, they are not probing the basics of transport phenomena between the involved phases. This work is aimed to bring new understanding of fluid-fluid interaction during low salinity water flooding through a series of organized experiments in which a crude oil sample with known properties was kept in contact with different brine solutions of various ionic strengths. Measuring brine pH, conductivity and crude oil viscosity and density for a period of 45 days illustrates the strong effect of the contact time and ionic strength on the dissociation of polar components and physical properties of the crude oil and brine. Besides, the interfacial tension(IFT) measurements show that the interfacial interactions are affected by several competitive interfacial processes. By decreasing the ionic strength of the brine, the solubility of naphthenic acids in the aqueous solution increases, and hence,the conductivity and the pH of the aqueous phase decrease. To verify this important finding, UV-Vis spectroscopy and 'H NMR analysis were also performed on aged brine samples. Notably, there is an ionic strength of brine in which the lowest IFT is observed, while the other physical properties are remained relatively unchanged.
文摘Understanding the roles of asphaltene and resin as natural surfactants existed in crude oil can enlighten contradicting reported results regarding interfacial tension(IFT) of crude oil/aqueous solution as a function of salinity and ion type. In this way, this study is aimed to investigate the effect of these natural surface active agents on IFT of with special focus on SO4^2-anion and Mg^2+cation. Two different synthetic oil solutions of 8 wt% of the extracted asphaltene and resin dissolved in toluene are prepared, and then IFT values are measured. After that,the obtained results are compared with the IFT of intact crude oil in contact with the same saline solutions examined in the previous stage. The obtained results showed a synergistic effect of Na2SO4+ MgCl2 solution unlike the MgSO4+ MgCl2 and CaSO4+ MgCl2 solutions on IFT reduction of resin at MgCl2 concentration of 15000 mg·kg^-1. In summary, it is found that the affinity of asphaltene molecules towards the interface of oleic phase/ionic solution leads to higher IFT variation.
文摘Nanofluids because of their surface characteristics improve the oil production from reservoirs by enabling different enhanced recovery mechanisms such as wettability alteration,interfacial tension(IFT)reduction,oil viscosity reduction,formation and stabilization of colloidal systems and the decrease in the asphaltene precipitation.To the best of the authors’ knowledge,the synthesis of a new nanocomposite has been studied in this paper for the first time.It consists of nanoparticles of both SiO2 and Fe3O4.Each nanoparticle has its individual surface property and has its distinct effect on the oil production of reservoirs.According to the previous studies,Fe3O4 has been used in the prevention or reduction of asphaltene precipitation and SiO2 has been considered for wettability alteration and/or reducing IFTs in enhanced oil recovery.According to the experimental results,the novel synthesized nanoparticles have increased the oil recovery by the synergistic effects of the formed particles markedly by activating the various mechanisms relative to the use of each of the nanoparticles in the micromodel individually.According to the results obtained for the use of this nanocomposite,understanding reservoir conditions plays an important role in the ultimate goal of enhancing oil recovery and the formation of stable emulsions plays an important role in oil recovery using this method.
文摘This study investigates the effect of injecting nanofluids containing nano-SiO_2 as drag reducing agents(DRA) at different concentrations on the pressure drop of air-water flow through horizontal pipe.The test fluid used in this study was air-water with nano-SiO_2 particles at 0.1%-1%mass concentration.The test sections of the experimental set-up were five pipes of the same length of 9 m with ID from 0.0127m-0.03175m(0.5 to 1.25 in).Airwater flow was run in slug flow regime under different volumetric flow rates.The results of drag reduction(η%)indicated that the addition of DRA could be efficient up to some dosage.Drag reduction performed much better for smaller pipe diameters than it did for larger ones.For various nanosilica concentrations,the maximum drag reduction was about 66.8%for 0.75%mass concentration of nanosilica.
文摘The e ects of CO2 and salt type on the interfacial tension(IFT) between crude oil and carbonated brine(CB) have not been fully understood. This study focuses on measuring the dynamic IFT between acidic crude oil with a total acid number of 1.5 mg KOH/g and fully CO2-saturated aqueous solutions consisting of 15,000 ppm of KCl, NaCl, CaCl2 and MgCl2 at 30 °C and a wide range of pressures(500–4000 psi). The results of IFT measurements showed that solvation of CO2 into all the studied aqueous solutions led to an increase in IFT of acidic crude oil(i.e., comparison of IFT of crude oil/CB and crude oil/brine), while no significant e ect was observed for pressure. In contrast, the obtained results of studied salts indicated a positive e ect on the IFT reduction of acidic crude oil/carbonated water(CW)(i.e., comparison of IFT of crude oil/CB and crude oil/CW).
文摘For syngas production, the combustion of fossil fuels produces large amounts of CO2 as a greenhouse gas annually which intensifies global warming. In this study, chemical looping combustion （CLC） has been utilized for the elimination of CO2 emission to atmosphere during simultaneous syngas production with different H2/CO ratio in steam reforming of methane （SR） and dry reforming of methane （DR） in a CLC-SR-DR configuration. In CLC-SR-DR with 184 reformer tubes （similar to an industrial scale steam reformer in Zagros Petrochemical Company, Assaluyeh, Iran）, DR reaction occurs over Rh-based catalysts in 31 tubes. Also, SR reaction is happened over Ni-based catalysts in 153 tubes. CLC via employment of Mn-based oxygen carriers supplies heat for DR and SR reactions and produces CO2 and H2O as raw materials simultaneously. A steady state heterogeneous catalytic reaction model is applied to analyze the performance and applicability of the proposed CLC-SR-DR configuration. Simulation results show that combustion efficiency reached 1 at the outlet of fuel reactor （FR）. Therefore, pure CO2 and H2O can be recycled to DR and SR sides, respectively. Also, CH4 conversion reached 0.2803 and 0.7275 at the outlet of SR and DR sides, respectively. Simulation results indicate that, 3223 kmol.h-l syngas with a H2/CO ratio equal to 9.826 was produced in SR side of CLC-SR-DR. After that, 1844 kmol.h-1 syngas with a H2/CO ratio equal to 0.986 was achieved in DR side of CLC-SR-DR. Results illustrate that by increasing the number of DR tubes to 50 tubes and considering 184 fixed total tubes in CLC-SR-DR, CH4 conversions in SR and DR sides decreased 2.69% and 3.31%, respectively. However, this subject caused total syngas production in SR and DR sides （in all of 184 tubes） enhance to 5427 kmol-h-1. Finally, thermal and molar behaviors of the proposed configuration demonstrate that CLC-SR-DR is applicable for simultaneous syngas production with high and low Hx/CO ratios in an environmental friendly process.
基金the financial and scientific supports from EOR Research Centre of Shiraz University and the Reservoir Modelling and Simulation Centre(RMSC)。
文摘In this study,the impacts of solutal Marangoni phenomenon on multiphase flow in static and micromodel geometries have experimentally been studied and the interactions between oil droplet and two different alkaline solutions(i.e.MgS04 and Na_2 CO_3) were investigated.The static tests revealed that the Marangoni convection exists in the presence of the alkaline and oil which should carefully be considered in porous media.In the micromodel experiments,observations showed that in the MgS04 flooding,the fluids stayed almost stationary,while in the Na2 C03 flooding,a spontaneous movement was detected.The changes in the distribution of fluids showed that the circular movement of fluids due to the Marangoni effects can be effective in draining of the unswept regions.The dimensional analysis for possible mechanisms showed that the viscous,gravity and diffusion forces were negligible and the other mechanisms such as capillary and Marangoni effects should be considered in the investigated experiments.The value of the new defined Marangoni/capillary dimensionless number for the Na2 C03 solution was orders of magnitude larger than the MgS04 flooding scenario which explains the differences between the two cases and also between different micromodel regions.In conclusion,the Marangoni convection is activated by creating an ultra-low IFT condition in multiphase flow problems that can be profoundly effective in increasing the phase mixing and microscopic efficiency.
文摘In this investigation, a novel thermally coupled reactor （TCR） containing methyl formate （MF） production in the endothermic side and methanol synthesis in the exothermic side has been investigated. The interesting feature of this TCR is that productive methanol in the exothermic side could be recycled and used as feed of endothermic side for MF synthesis. Other important advantages of the proposed system are high production rates of hydrogen and MF. The configuration consists of two thermally coupled concentric tubular reactors. In these coupled reactors, autothermal system is obtained within the reactor. A steady-state heterogeneous model is used for simulation of the coupled reactor. The proposed model has been utilized to compare the performance of TCR with the conventional methanol reactor （CMR）. Noticeable enhancement can be obtained in the performance of the reactors. The influence of operational parameters is studied on reactor performance. The results show that coupling of these reactions could be feasible and beneficial. Experimental proof-of-concept is required to validate the operation of the novel reactor.
文摘Unwanted water production together with oil and gas production is a striking problem in oil and gas industries, and many approaches have been examined to overcome this major problem. Preformed particle gels (PPGs) showed dramatically good properties for this purpose in mature oil and gas reservoirs. In this study, we carefully synthesized an efficient series of PPGs with using a design of experiments (DOE) software. Acrylamide (AAm)/Acrylic acid (AA) mole ratio, N,N’-methylenebisacrylamide (MBA) mole percentage and swelling time were considered as key parameters to examine PPG swelling behavior. Our results presented a detailed empirical correlation, which could significantly predict the swelling capacity of PPGs in CaCl2 salt solution (200,000 ppm).
基金financial support from National Iranian South Oil Company(NISOC)
文摘Most fractured carbonate oil reservoirs have oil-wet rocks.Therefore,the process of imbibing water from the fractures into the matrix is usually poor or basically does not exist due to negative capillary pressure.To achieve appropriate ultimate oil recovery in these reservoirs,a water-based enhanced oil recovery method must be capable of altering the wettability of matrix blocks.Previous studies showed that carbonated water can alter wettability of carbonate oil-wet rocks toward less oil-wet or neutral wettability conditions,but the degree of modification is not high enough to allow water to imbibe spontaneously into the matrix blocks at an effective rate.In this study,we manipulated carbonated brine chemistry to enhance its wettability alteration features and hence to improve water imbibition rate and ultimate oil recovery upon spontaneous imbibition in dolomite rocks.First,the contact angle and interfacial tension(IFT)of brine/crude oil systems were measured for several synthetic brine samples with different compositions.Thereafter,two solutions with a significant difference in WAI(wettability alteration index)but approximately equal brine/oil IFT were chosen for spontaneous imbibition experiments.In the next step,spontaneous imbibition experiments at ambient and high pressures were conducted to evaluate the ability of carbonated smart water in enhancing the spontaneous imbibition rate and ultimate oil recovery in dolomite rocks.Experimental results showed that an appropriate adjustment of the imbibition brine(i.e.,carbonated smart water)chemistry improves imbibition rate of carbonated water in oil-wet dolomite rocks as well as the ultimate oil recovery.
基金Shiraz University Enhanced Oil Recovery(EOR)Research Center for the support
文摘Viscous fingering is one of the main challenges that could reduce areal sweep efficiency during waterflooding in oil reservoirs. A series of waterflooding experiments were carried out in a Hele-Shaw cell at ambient temperature during which areal sweep efficiency was estimated and techniques to ease the fingering problem were examined. The onset and propagation of viscous fingers were monitored as a function of both injection rate and injection/production positions. Image processing techniques were utilized to quantitatively investigate the propagation of fingers. The experimental results show that, under specific conditions, increasing the number of finger branches could improve the areal sweep efficiency, whereas growth of a single narrow finger has a negative impact on oil displacement efficiency. According to the obtained results,increasing the injection rate improves the areal sweep efficiency up to a critical rate at which viscous fingers start to grow.The impact of heterogeneity of the medium on distributing the viscous fingers was also investigated by introducing two different arrangements of fractures in the model. The results show that fractures perpendicular to the direction of flow would distribute the displacing water more uniformly, while fractures in the direction of flow would amplify the unfavorable sweep efficiency.
文摘Composition estimation plays very important role in plant operation and control.Extended Kalman filter(EKF) is one of the most common estimators,which has been used in composition estimation of reactive batch distillation,but its performance is heavily dependent on the thermodynamic modeling of vapor-liquid equilibrium,which is difficult to initialize and tune.In this paper an inferential state estimation scheme based on adaptive neuro-fuzzy inference system(ANFIS) ,which is a model base estimator,is employed for composition estimation by using temperature measurements in multicomponent reactive batch distillation.The state estimator is supported by data from a complete dynamic model that includes component and energy balance equations accompanied with thermodynamic relations and reaction kinetics.The mathematical model is verified by pilot plant data.The simulation results show that the ANFIS estimator provides reliable and accurate estimation for component concentrations in reactive batch distillation.The estimated states form a basis for improving the performance of reactive batch distillation either through decision making of an operator or through an automatic closed-loop control scheme.
基金the financial supports from the National Key Research and Development Program of China (2016YFB0101203)China MOST (Ministry of Science and Technology) Innovation Team in Key Area (2016RA4053)+2 种基金the National Natural Science Foundation of China (21276252)Natural Science Foundation of Liaoning Province (2015020630)State Key Laboratory of Fine Chemicals (Panjin) (JH2014009)
文摘For improvement of vanadium redox flow battery （VRB） performance, novel amphoteric semi- interpenetrating membranes （ASIPN） were prepared using poly（ether ether ketone） （PEEK） and polysul- fone （PSf）, the former bearing sulfonic groups and the latter imidazolium. These two groups form ionic crosslinks between PEEK and PSf; meanwhile, covalent cross links were built between PSf chains with ad- dition of N-（3-aminopropyl）-imidazole. The amphoteric nature of the membrane allows facile proton and anion transport; the IPN structure and the presence of imidazolium cation effectively suppress vanadium ion crossover through the membrane. Therefore, the ASIPN based VRBs show higher Coulombic efficiency and energy efficiency than that assembled with pristine SPEEK and Nation 212 membranes. Our work demonstrates that the ASIPN membranes are promising for VRB applications.
文摘Encouraged by the wide spectrum of novel applications of gas hydrates,e.g.,energy recovery,gas separation,gas storage,gas transportation,water desalination,and hydrogen hydrate as a green energy resource,as well as CO2 capturing,many scientists have focused their attention on investigating this important phenomenon.Of course,from an engineering viewpoint,the mathematical modeling of gas hydrates is of paramount importance,as anticipation of gas hydrate stability conditions is effective in the design and control of industrial processes.Overall,the thermodynamic modeling of gas hydrate can be tackled as an equilibration of three phases,i.e.,liquid,gas,and solid hydrate.The inseparable component in all hydrate systems,water,is highly polar and non-ideal,necessitating the use of more advanced equation of states(EoSs) that take into account more intermolecular forces for thermodynamic modeling of these systems.Motivated by the ever-increasing number of publications on this topic,this study aims to review the application of associating EoSs for the thermodynamic modeling of gas hydrates.Three most important hydrate-based models available in the literature including the van der Waals-Platteeuw(vdW-P) model,Chen-Guo model,and Klauda-Sandler model coupled with and SAFT EoSs were investigated and compared with cubic EoSs.It was concluded that the CPA and SAFT EoSs gave very accurate results for hydrate systems as they take into account the association interactions,which are very crucial in gas hydrate systems in which water,methanol,glycols,and other types of associating compounds are available.Moreover,it was concluded that the CPA EoS is easier to use than the SAFT-type EoSs and our suggestion for the gas hydrate systems is the CPA EoS.
文摘Foam injection is a promising solution for control of mobility in oil and gas field exploration and development,including enhanced oil recovery,matrix-acidization treatments,contaminated-aquifer remediation and gas leakage prevention.This study presents a numerical investigation of foam behavior in a porous medium.Fractional flow method is applied to describe steady-state foam displacement in the entrance region.In this model,foam flow for the cases of excluding and including capillary pressure and for two types of gas,nitrogen(N2)and carbon dioxide(CO2)are investigated.Effects of pertinent parameters are also verified.Results indicate that the foam texture strongly governs foam flow in porous media.Required entrance region may be quite different for foam texture to accede local equilibrium,depending on the case and physical properties that are used.According to the fact that the aim of foaming of injected gas is to reduce gas mobility,results show that CO2 is a more proper injecting gas than N2.There are also some ideas presented here on improvement in foam displacement process.This study will provide an insight into future laboratory research and development of full-field foam flow in a porous medium.
文摘In this study, radial flow moving bed reactors for isobutane dehydrogenation have been modeled and simulated heterogeneously based on mass and energy conservation laws. The considered reaction networks in the model are isobutene dehydrogenation as main reaction, and hydrogenolysis, propane dehydrogenation as well as coke formation as side reactions that all occur on the catalyst surface. Then, the process condition has been optimized to produce more isobutene under steady state condition. To prove the accuracy of the considered mathematical model and assumptions, simulation results are compared with the plant data. As a powerful method in the global optimization, the genetic algorithm has been used to optimize the considered objective function. The isobutane conversion and isobutene selectivity under optimal conditions are about 40.1% and 91%, respectively.
