To investigate the influences of co-flowand counter-flowmodes of reactant flowarrangement on a proton exchange membrane fuel cell(PEMFC)during start-up,unsteady physical and mathematical models fully coupling the flow...To investigate the influences of co-flowand counter-flowmodes of reactant flowarrangement on a proton exchange membrane fuel cell(PEMFC)during start-up,unsteady physical and mathematical models fully coupling the flow,heat,and electrochemical reactions in a PEMFC are established.The continuity equation and momentum equation are solved by handling pressure-velocity coupling using the SIMPLE algorithm.The electrochemical reaction rates in the catalyst layers(CLs)of the cathode and anode are calculated using the Butler-Volmer equation.The multiphase mixture model describes the multiphase transport process of gas mixtures and liquid water in the fuel cell.After validation,the influences of co-flow and counter-flow modes on the PEMFC performance are investigated,including the evolution of the current density,flow field,temperature field,and reactant concentration field during start-up,as well as the steady distribution of the current density,reactant concentration,andmembrane water content when the start-up stabilizes.Co-flow and counter-flow modes influence the current density distribution and temperature distribution.On the one hand,the co-flow mode accelerates the start-up process of the PEMFC and leads to a more evenly distributed current density than the counter-flow mode.On the other hand,the temperature difference between the inlet and outlet sections of the cell is up to 10.1℃ under the co-flow mode,much larger than the 5.0℃ observed in the counter-flow mode.Accordingly,the counter-flowmode results in a more evenly distributed temperature and a lower maximum temperature than the co-flow case.Therefore,in the flow field design of a PEMFC,the reactant flow arrangements can be considered to weigh between better heat management and higher current density distribution of the cell.展开更多
Magnesium is one of the largely available elements in the earth’s crust. It has a low structural density with high specific strength. This unique material property has forced an increase in the use of magnesium and i...Magnesium is one of the largely available elements in the earth’s crust. It has a low structural density with high specific strength. This unique material property has forced an increase in the use of magnesium and its alloys in various applications pertaining to industrial sector,automobiles, aerospace and biomedical. Since magnesium is a highly reactive metal, it is prone to higher rate of corrosion as compared to its counterparts. Thus, it is essential to analyze the corrosion behavior of magnesium and its alloys in its applications. An appropriate process is to be followed in the design and development of magnesium alloys which overcome the limitations of magnesium and enhance the desired material properties in accordance to their applications. This review paper summarizes the importance of magnesium and its material properties. The influence of various alloying elements on the mechanical properties of magnesium is reviewed. The broad classification of Mg alloys and their behavioral trends are detailed. The corrosion behavior of magnesium and the influence of corrosion products on the material characteristics of magnesium, in aqueous medium, are discussed. The manufacturing techniques of magnesium alloys along with the secondary techniques are also covered. The various applications and the limitations of magnesium in these applications are covered. A complete section is dedicated towards detailing the recent trends of magnesium(Mg) alloys, i.e., the biodegradable nature and applications of Mg alloys. The influence of biocorrosion on Mg alloys and techniques to overcome it have been deliberated. This paper provides a thorough review on recent developments of magnesium with respect to engineering applications.展开更多
A modified failure criterion is proposed to determine the strength of transversely isotropic rocks. Me-chanical properties of some metamorphic and sedimentary rocks including gneiss, slate, marble, schist, shale, sand...A modified failure criterion is proposed to determine the strength of transversely isotropic rocks. Me-chanical properties of some metamorphic and sedimentary rocks including gneiss, slate, marble, schist, shale, sandstone and limestone, which show transversely isotropic behavior, were taken into consider-ation. Afterward, introduced triaxial rock strength criterion was modified for transversely isotropic rocks. Through modification process an index was obtained that can be considered as a strength reduction parameter due to rock strength anisotropy. Comparison of the parameter with previous anisotropy in-dexes in literature showed reasonable results for the studied rock samples. The modified criterion was compared to modified Hoek-Brown and Ramamurthy criteria for different transversely isotropic rocks. It can be concluded that the modified failure criterion proposed in this study can be used for predicting the strength of transversely isotropic rocks.展开更多
Honji instability and ringing of offshore structrures are two different phenomena. Honji instability occurs at a circular cylinder in transverse periodic finite motion in a water tank. It is superposed on the streamin...Honji instability and ringing of offshore structrures are two different phenomena. Honji instability occurs at a circular cylinder in transverse periodic finite motion in a water tank. It is superposed on the streaming flow induced by the cylinder’s boundary layer. Its oscillation period is half of the period of the cylinder oscillation. Finite volume calculations of the filtered Navier-Stokes equations visualize the three-dimensional instability, where fluid particles transported by the circumferencial roll pairs exhibit a periodic mushroom-like pattern. Force is the same with and without the Honji instability. The large eddy simulation calculations for high Reynolds number support a drag coefficient in accordance with the Stokes-Wang solution below separation and conform with experimental measurements of the damping force on a harmonically oscillating cylinder. Ringing of offshore structures are vibrations which appear at natural frequencies and concern fatigue. It is generated by a higher harmonic force oscillating with frequency being 3-4 times the fundamental wave frequency. Together with a strong inertia load in phase with the incoming wave’s acceleration, a secondary load cycle appears in strong seas when the wave crest leaves the structure; this occurs about 1/4 wave period after the main force peak, it starts when the wave crest is about one cylinder radius behind the cylinder, lasts for about 15-20 percent of the wave period and has a magnitude up to 11 % of the peak-to-peak total force. It is a gravity effect and appears in strong irregular seas when kA > 0.18 and um/√gD > 0.4 (k wavenumber, A amplitude, um maximal wave induced velocity, g acceleration of gravity, D cylinder diameter).展开更多
A review of the main mechanisms influencing turbulent modulation in the presence of spherical and non-spherical particles is presented. The review demonstrates the need for more numerical and experimental work with hi...A review of the main mechanisms influencing turbulent modulation in the presence of spherical and non-spherical particles is presented. The review demonstrates the need for more numerical and experimental work with higher accuracy than obtained so far and the need to resolve the flow near the surface of particles with the aim to re-evaluate the quantitative effect of different parameters on turbulent modulation. The review reveals that non-spherical particles have more adverse effect on turbulence as compared to spherical ones, for the same ambient conditions.展开更多
The wave diffraction-radiation problem of a porous geometry of arbitrary shape located in the free surface of a fluid is formulated by a set of integral equations, assuming a linear resistance law at the geometry. The...The wave diffraction-radiation problem of a porous geometry of arbitrary shape located in the free surface of a fluid is formulated by a set of integral equations, assuming a linear resistance law at the geometry. The linear forces, the energy relation and the mean horizontal drift force are evaluated for non-porous and porous geometries. A geometry of large porosity has an almost vanishing added mass. The exciting forces are a factor of 5–20 smaller compared to a solid geometry. In the long wave regime, the porous geometry significantly enhances both the damping and the mean drift force, where the latter grows linearly with the wavenumber. The calculated mean drift force on a porous hemisphere and a vertical truncated cylinder, relevant to the construction of fish cages, is compared to available published results.展开更多
The paper presents and discusses theoretical bases and methodology of development of two- and three-dimensional analytical and optical isodynes. Atten- tion is given to the theoretical admissibility of the major compo...The paper presents and discusses theoretical bases and methodology of development of two- and three-dimensional analytical and optical isodynes. Atten- tion is given to the theoretical admissibility of the major components of the physical and mathematical models which are taken as the theoretical basis of the isodynes, and of the related analytical and experimental procedures of stress analysis. Efficiency and reliability of the nondestructive isodyne stress analysis are discussed.展开更多
The ultra-sonic gas atomization （USGA） nozzle is an important apparatus in the metal liquid air-blast atomization process. It can generate oscillating supersonic gas effiux, which is proved to be effective to enforc...The ultra-sonic gas atomization （USGA） nozzle is an important apparatus in the metal liquid air-blast atomization process. It can generate oscillating supersonic gas effiux, which is proved to be effective to enforce the atomization and produce narrow-band particle distributions. A double-actuator ultra-sonic gas nozzle is proposed in the present paper by joining up two active signals at the ends of the resonance tubes. Numerical sim- ulations axe adopted to study the effects of the flow development on the acoustic resonant properties inside the Haxtmann resonance cavity with/without actuators. Comparisons show that the strength and the onset process of oscillation are enhanced remarkably with the actuators. The multiple oscillating amplitude peaks are found on the response curves, and two kinds of typical behaviors, i.e., the Hartmann mode and the global mode, are discussed for the corresponding frequencies. The results for two driving actuators are also investigated. When the amplitudes, the frequencies, or the phase difference of the input signals of the actuators are changed, the oscillating amplitudes of gas effiux can be altered effectively.展开更多
Active geological and young faulted zones have made Iran's territory one of the most seismological active areas in the world according to recent historical earthquakes.Some of the deadliest earthquakes such as Gil...Active geological and young faulted zones have made Iran's territory one of the most seismological active areas in the world according to recent historical earthquakes.Some of the deadliest earthquakes such as Gilan 1990 and Kermanshah 2018 caused tens of thousands fatalities.If such violent earthquakes affect strategical structures of a country,indirect losses would be more concerning than direct losses.Nowadays there is no doubt about the vital role of tunnels and underground structures in urban areas.These facilities serve as nonstop functional structures for human transportation,water and sewage systems and underground pedestrian ways.Any external hazard subjected to underground spaces,such as earthquake could directly affect passenger's lives and significantly decrease whole system reliability of public transportation.Commonly two earthquake levels of intensities,Maximum Design Earthquake(MDE)and Operating Design Earthquake(ODE)were used in seismic design of underground structures.However,uncertain nature of earthquakes in terms of frequency content,duration of strong ground motion,and level of intensity indicate that only the two levels of earthquake(ODE and MDE)cannot cover the all range of possible seismic responses of structures during a probable earthquake.It is important to evaluate the behavior of tunnel under a wide range of earthquake intensities.For this purpose,a practical risk-based approach which is obtained using the total probability rule was used.This study illustrates a framework for evaluation seismic stability of tunnels.Urban railway tunnels of Tehran,Shiraz,Ahwaz,Mashhad,Isfahan and Tabriz were considered as study cases.Nominal value of seismic risk for three main damage states,including minor,moderate and major were calculated.展开更多
The structures of water inside and outside （6,6）, （8,8）, and （10,10） single- walled carbon nanotubes （SWCNTs） under an electric field perpendicular to the tube axis are investigated by molecular dynamics simul...The structures of water inside and outside （6,6）, （8,8）, and （10,10） single- walled carbon nanotubes （SWCNTs） under an electric field perpendicular to the tube axis are investigated by molecular dynamics simulations. The results show that dipole reorientation induced by electric field plays a significant role on the structures of confined water inside and outside SWCNTs. Inside SWCNTs, the average water occupancy and the average number of hydrogen bonds （H-bonds） per water molecule decrease as the electric intensity increases. Because the field intensity is sufficiently strong, the initial water structures inside the SWCNTs are destroyed, and the isolated water clusters are found. Outside SWCNTs, the azimuthal distributions of the density and the average number of H-bonds per water molecule around the solid walls become more and more asymmetric as the electric intensity increases. The percentages of water molecules involved in 0-5 H-bonds for all the three types of SWCNTs under different field intensities are displayed. The results show that those water molecules involved with most H-bonds are the most important to hold the original structures. When the electric field direction is parallel with the original preferred orientation, the density and the H-bond connections in water will be increased; when the electric field direction is perpendicular to the original preferred orientation, the density and the H-bond connections in water will be decreased.展开更多
The molecular dynamics simulations are performed to show that in aque- ous environments, a short single-walled carbon nanotube （SWCNT） guided by a long SWCNT, either inside or outside the longer tube, is capable of ...The molecular dynamics simulations are performed to show that in aque- ous environments, a short single-walled carbon nanotube （SWCNT） guided by a long SWCNT, either inside or outside the longer tube, is capable of moving along the nanotube axis unidirectionally in an electric field perpendicular to the carbon nanotube （CNT） axis with the linear gradient. The design suggests a new way of molecule transportation or mass delivery. To reveal the mechanism behind this phenomenon, the free energy profiles of the system are calculated by the method of the potential of mean force （PMF）.展开更多
A method for measurement of ultra-low flying height in head-disk spacing is described. Three different wavelengths are selected out from white light by filters to measure the spacing simultaneously. Besides solving th...A method for measurement of ultra-low flying height in head-disk spacing is described. Three different wavelengths are selected out from white light by filters to measure the spacing simultaneously. Besides solving the ambiguity problem, a more reliable result is achieved by using weighted average of measurement results from three different wavelengths, where the weight is dependent upon spacing. Fringe-bunching correction algorithm （FBC） and spot-tilling technique are adopted to suppress calibration and random errors. Moreover, incident bandwidth correction （IBC） method is introduced to compensate the error caused by low monochromaticity of incident light. Based on dynamic flying height tester （DFHT Ⅱ）, with the redesigned of photo-electric conversion and signal acquirement module, an instrument has been developed. And comparing the experimental data from the instrument with those from a KLA-FHT D6, the discrepancy is less than 5%. It indicates that the instrument is suitable to perform ultra-low flying height measurement and satisfies the reauirement of magnetic heads manufacturing.展开更多
For investigation of equilibrium conditions of electrons in an atom, and Ionization Energies of Elements, a simplified deterministic static model is proposed. The electrons are initially uniformly and sparsely arrange...For investigation of equilibrium conditions of electrons in an atom, and Ionization Energies of Elements, a simplified deterministic static model is proposed. The electrons are initially uniformly and sparsely arranged on the outer surface of nucleus. Then, by taking into account the nucleus-electron interaction (attractive and repulsive) and the mutual electron-electron repulsions, and by a simple step-by-step nonlinear static analysis program, all the electrons are found to equilibrate on the outer surface of the same sphere, which is concentric and larger than nucleus. In a second stage, starting from an equilibrium sphere of electrons, one of the electrons is subjected to gradual forced removal, radially and outwards with respect to nucleus. Within each removal step, the produced work increment is determined and the increments are summed. When no more significant attraction is exerted by nucleus to removed electron, the total work gives the Ionization Energy. After removing of single electron, the remaining electrons fall on a lower shell, that is, they equilibrate on the outer surface of a smaller concentric sphere. For nucleus-electron interaction, an L-J (Lennard-Jones) type curve, attractive and repulsive, is adopted. When the parameter of this curve is n > 1.0, the Ionization Energy exhibits an upper bound. As parameter n increases from 1.0 up to 2.0, the attractive potential of L-J curve is gradually weakened. The proposed model is applied on Argon. It is observed that, as the number of electrons increases, the radius of equilibrium sphere increases, too, whereas the attractive nucleus-electron potential is reduced;thus the Ionization Energy is reduced, too. Particularly, as the number of electrons and the radius of equilibrium sphere exceed some critical values, the above two last quantities exhibit abrupt falls. A regular polyhedron is revealed, which can accommodate Elements up to atomic number Z = 146, that is 28 more than Z = 118 of existing last Element, as guide for initial locations of electrons in the above first program.展开更多
Nanoprecipitation strengthening has been widely adopted as an effective way to design high-strength alloys,which generally leads to the loss of ductility. Here we unveil the unique bifunctionality of L12-structurednan...Nanoprecipitation strengthening has been widely adopted as an effective way to design high-strength alloys,which generally leads to the loss of ductility. Here we unveil the unique bifunctionality of L12-structurednanoprecipitates in a FeCoNiAlTi-type high entropy alloy , enabling the combined increase of tensile strength andductility. Results show that as-quenched precipitate-free matrix alloys undergo thermally-induced martensitetransformation and form the body-centered cubic martensite phase with limited tensile ductility. In strongcontrast, when introducing the dense coherent L12-type nanoprecipitates, the face-centered cubic matrix istemporarily stabilized, which in turn promotes the microbands-induced plasticity associated with stress-inducedmartensite transformation upon deformation. This allows us to achieve significantly improved work hardeningcapability and excellent plastic deformation stability at a high-strength level. These new findings reshape ourunderstanding of the precipitation strengthening and could provide useful guidance for developing highperformance alloys by regulating the coherent nanoprecipitate and martensitic phase transformation.展开更多
Electromagnetic forming is a high-speed forming technology by which hollow profiles can be compressed or expanded. It is done with a pulsed magnetic field to apply Lorentz’ forces at electrically conductive material....Electromagnetic forming is a high-speed forming technology by which hollow profiles can be compressed or expanded. It is done with a pulsed magnetic field to apply Lorentz’ forces at electrically conductive material. Electromagnetic hollow tube expansion is limited by the fragmentation tendency. This work attempts to use a combination of analytical and computational approach to compute the net tangential stress during tube expansion. A simplified analytical framework to estimate the temporal evolution of plastic stresses present in aluminium alloy AA5052 at low and high applied magnetic pressures is developed based upon dynamic imaging. The time resolved images captured using current synchronised high speed camera record the overall dimensional changes of the tube that is validated by multi-physics simulation of expansion process. Imaging of hollow tube expansions at two selected peak currents has been carried out at various current levels in the range 76 - 160 kA. The direct visualisation of the increase in the tube diameter at two current levels provided a comparison of the developing net tangential stresses in the hollow tube during the undamaged and fragmented expansion. Imaging of tube expansion also facilitates the estimation of the strain rate experienced by the tube and was in the range of ~1700 s<sup>-1</sup> to ~1200 s<sup>-1</sup>. The propensity of fragmentation was found to be due to the level and duration of generated tangential stresses above the yield stress during expansion of the aluminium tubes. Presented study provides a mean of exploiting the enhanced formability of aluminium alloys using electromagnetic forming.展开更多
This work reports the successful outcomes to process the polyester, acrylic and wool fiber along with jute fiber exclusively using existing jute processing machineries for manufacturing the 241 tex jute blended yarn. ...This work reports the successful outcomes to process the polyester, acrylic and wool fiber along with jute fiber exclusively using existing jute processing machineries for manufacturing the 241 tex jute blended yarn. The blending was performed at feeding stage of breaker carding machine and blending ratio of jute and polyester/acrylic/wool fibers is 80:20. Manufacturing of jute blended yarns will create a new opportunity for extending the uses of jute fibers in value added jute products. The present work is concerned with the investigation of physical properties such as tenacity, elongation % at break, quality ratio, unevenness, imperfections (thick, thin & neps) and hairiness of manufactured jute blended yarns. The jute-polyester (80/20) blended yarn shows the higher strength and more evenness compared to jute-acrylic (80/20), jute-wool (80/20) blended and 100% jute yarn.展开更多
Accurate watermelon yield estimation is crucial to the agricultural value chain,as it guides the allocation of agricultural resources as well as facilitates inventory and logistics planning.The conventional method of ...Accurate watermelon yield estimation is crucial to the agricultural value chain,as it guides the allocation of agricultural resources as well as facilitates inventory and logistics planning.The conventional method of watermelon yield estimation relies heavily onmanual labor,which is both time-consuming and labor-intensive.To address this,this work proposes an algorithmic pipeline that utilizes unmanned aerial vehicle(UAV)videos for detection and counting of watermelons.This pipeline uses You Only Look Once version 8 s(YOLOv8s)with panorama stitching and overlap partitioning,which facilitates the overall number estimation ofwatermelons in field.The watermelon detection model,based on YOLOv8s and obtained using transfer learning,achieved a detection accuracy of 99.20%,demonstrating its potential for application in yield estimation.The panorama stitching and overlap partitioning based detection and counting method uses panoramic images as input and effectively mitigates the duplications comparedwith the video tracking based detection and countingmethod.The counting accuracy reached over 96.61%,proving a promising application for yield estimation.The high accuracy demonstrates the feasibility of applying this method for overall yield estimation in large watermelon fields.展开更多
A theoretical model is developed to predict the upper limit heat transfer between a stack of parallel plates subject to multiphase cooling by air-mist flow.The model predicts the optimal separation distance between th...A theoretical model is developed to predict the upper limit heat transfer between a stack of parallel plates subject to multiphase cooling by air-mist flow.The model predicts the optimal separation distance between the plates based on the development of the boundary layers for small and large separation distances,and for dilute mist conditions.Simulation results show the optimal separation distance to be strongly dependent on the liquid-to-air mass flow rate loading ratio,and reach a limit for a critical loading.For these dilute spray conditions,complete evaporation of the droplets takes place.Simulation results also show the optimal separation distance decreases with the increase in the mist flow rate.The proposed theoretical model shall lead to a better understanding of the design of fins spacing in heat exchangers where multiphase spray cooling is used.展开更多
A Euler-Lagrangian simulation was employed for a comprehensive parameter study of wood gasification in a fluidized charcoal bed. The parameters that were varied include the initial bed temperature, fuel mass flow rate...A Euler-Lagrangian simulation was employed for a comprehensive parameter study of wood gasification in a fluidized charcoal bed. The parameters that were varied include the initial bed temperature, fuel mass flow rate, inert tar fraction, and kinetic energy losses caused by particle-particle and particle-wall colli- sions. The results of each parameter variation are compared with a base scenario, previously described in detail in Part I of this study （Gerber ＆ Oevermann, 2014）. The results are interpreted by comparing the reactor outlet temperature, averaged particle temperature, overall wood mass, overall charcoal mass, concentrations of several gaseous species, and axial barycenter data for particles obtained with differ- ent sets of parameters. The inert tar fraction and fuel mass flow rate are the most sensitive parameter, while the particle-particle and particle-wall contact parameters have only a small impact on the results. Increasing the reactive tar components by 19% almost doubled the amount of reactive tars at the reac- tor outlet, while decreasing the restitution coefficients of the particle collisions by 0.2 results in higher overall gas production but almost no change in bed height. Herein, our numerical results are discussed in detail while assessing the model restrictions.展开更多
Statistical analysis of pressure fluctuations in spouted beds has been used as a well-established diagnostic tool to determine bed and flow characteristics because of its smooth operation. However, in many recent and ...Statistical analysis of pressure fluctuations in spouted beds has been used as a well-established diagnostic tool to determine bed and flow characteristics because of its smooth operation. However, in many recent and conventional applications of spouted beds such as drying, coal gasification, catalytic conversion, biomass treatment, and chemical vapor deposition, direct estimation of the heat transfer rate from the solid bed to the gas or vice versa has proven to be difficult. A variance and spectral analysis of pressure fluctuation is extended here to characterize the heat transfer phenomena in a spouted bed. In the present study, zirconia and alumina were used as the bed materials, and argon and nitrogen were used as the spouting gases. Experiments were conducted at various heating rates for different superficial gas velocities for a range of temperatures up to 300 °C. Significant changes in the gas density and viscosity with different extents of heat transfer were observed to affect the momentum diffusivity and gas–particle interaction, which in turn led to local pressure fluctuations, causing the bed to behave differently. In the present work, a novel approach is proposed to establish a link between local pressure fluctuation and the extent of heat transfer in the bed. This method shows potential for correlation of the statistics of pressure fluctuation with the thermal properties of individual solids and gases. Thus, the technique can be extended to many industrial applications for the indirect estimation of the extent of heat transfer and prediction of unknown thermal properties of products in solids or gases.展开更多
基金supported by the Projects of Talents Recruitment of Guangdong University of Petrochemical Technology(No.2018rc14)Maoming City Science and Technology Plan Project(Nos.210427094551264 and 220415004552411).
文摘To investigate the influences of co-flowand counter-flowmodes of reactant flowarrangement on a proton exchange membrane fuel cell(PEMFC)during start-up,unsteady physical and mathematical models fully coupling the flow,heat,and electrochemical reactions in a PEMFC are established.The continuity equation and momentum equation are solved by handling pressure-velocity coupling using the SIMPLE algorithm.The electrochemical reaction rates in the catalyst layers(CLs)of the cathode and anode are calculated using the Butler-Volmer equation.The multiphase mixture model describes the multiphase transport process of gas mixtures and liquid water in the fuel cell.After validation,the influences of co-flow and counter-flow modes on the PEMFC performance are investigated,including the evolution of the current density,flow field,temperature field,and reactant concentration field during start-up,as well as the steady distribution of the current density,reactant concentration,andmembrane water content when the start-up stabilizes.Co-flow and counter-flow modes influence the current density distribution and temperature distribution.On the one hand,the co-flow mode accelerates the start-up process of the PEMFC and leads to a more evenly distributed current density than the counter-flow mode.On the other hand,the temperature difference between the inlet and outlet sections of the cell is up to 10.1℃ under the co-flow mode,much larger than the 5.0℃ observed in the counter-flow mode.Accordingly,the counter-flowmode results in a more evenly distributed temperature and a lower maximum temperature than the co-flow case.Therefore,in the flow field design of a PEMFC,the reactant flow arrangements can be considered to weigh between better heat management and higher current density distribution of the cell.
文摘Magnesium is one of the largely available elements in the earth’s crust. It has a low structural density with high specific strength. This unique material property has forced an increase in the use of magnesium and its alloys in various applications pertaining to industrial sector,automobiles, aerospace and biomedical. Since magnesium is a highly reactive metal, it is prone to higher rate of corrosion as compared to its counterparts. Thus, it is essential to analyze the corrosion behavior of magnesium and its alloys in its applications. An appropriate process is to be followed in the design and development of magnesium alloys which overcome the limitations of magnesium and enhance the desired material properties in accordance to their applications. This review paper summarizes the importance of magnesium and its material properties. The influence of various alloying elements on the mechanical properties of magnesium is reviewed. The broad classification of Mg alloys and their behavioral trends are detailed. The corrosion behavior of magnesium and the influence of corrosion products on the material characteristics of magnesium, in aqueous medium, are discussed. The manufacturing techniques of magnesium alloys along with the secondary techniques are also covered. The various applications and the limitations of magnesium in these applications are covered. A complete section is dedicated towards detailing the recent trends of magnesium(Mg) alloys, i.e., the biodegradable nature and applications of Mg alloys. The influence of biocorrosion on Mg alloys and techniques to overcome it have been deliberated. This paper provides a thorough review on recent developments of magnesium with respect to engineering applications.
文摘A modified failure criterion is proposed to determine the strength of transversely isotropic rocks. Me-chanical properties of some metamorphic and sedimentary rocks including gneiss, slate, marble, schist, shale, sandstone and limestone, which show transversely isotropic behavior, were taken into consider-ation. Afterward, introduced triaxial rock strength criterion was modified for transversely isotropic rocks. Through modification process an index was obtained that can be considered as a strength reduction parameter due to rock strength anisotropy. Comparison of the parameter with previous anisotropy in-dexes in literature showed reasonable results for the studied rock samples. The modified criterion was compared to modified Hoek-Brown and Ramamurthy criteria for different transversely isotropic rocks. It can be concluded that the modified failure criterion proposed in this study can be used for predicting the strength of transversely isotropic rocks.
基金funded by the Research Council of Norway through NFR 191204/V30
文摘Honji instability and ringing of offshore structrures are two different phenomena. Honji instability occurs at a circular cylinder in transverse periodic finite motion in a water tank. It is superposed on the streaming flow induced by the cylinder’s boundary layer. Its oscillation period is half of the period of the cylinder oscillation. Finite volume calculations of the filtered Navier-Stokes equations visualize the three-dimensional instability, where fluid particles transported by the circumferencial roll pairs exhibit a periodic mushroom-like pattern. Force is the same with and without the Honji instability. The large eddy simulation calculations for high Reynolds number support a drag coefficient in accordance with the Stokes-Wang solution below separation and conform with experimental measurements of the damping force on a harmonically oscillating cylinder. Ringing of offshore structures are vibrations which appear at natural frequencies and concern fatigue. It is generated by a higher harmonic force oscillating with frequency being 3-4 times the fundamental wave frequency. Together with a strong inertia load in phase with the incoming wave’s acceleration, a secondary load cycle appears in strong seas when the wave crest leaves the structure; this occurs about 1/4 wave period after the main force peak, it starts when the wave crest is about one cylinder radius behind the cylinder, lasts for about 15-20 percent of the wave period and has a magnitude up to 11 % of the peak-to-peak total force. It is a gravity effect and appears in strong irregular seas when kA > 0.18 and um/√gD > 0.4 (k wavenumber, A amplitude, um maximal wave induced velocity, g acceleration of gravity, D cylinder diameter).
文摘A review of the main mechanisms influencing turbulent modulation in the presence of spherical and non-spherical particles is presented. The review demonstrates the need for more numerical and experimental work with higher accuracy than obtained so far and the need to resolve the flow near the surface of particles with the aim to re-evaluate the quantitative effect of different parameters on turbulent modulation. The review reveals that non-spherical particles have more adverse effect on turbulence as compared to spherical ones, for the same ambient conditions.
文摘The wave diffraction-radiation problem of a porous geometry of arbitrary shape located in the free surface of a fluid is formulated by a set of integral equations, assuming a linear resistance law at the geometry. The linear forces, the energy relation and the mean horizontal drift force are evaluated for non-porous and porous geometries. A geometry of large porosity has an almost vanishing added mass. The exciting forces are a factor of 5–20 smaller compared to a solid geometry. In the long wave regime, the porous geometry significantly enhances both the damping and the mean drift force, where the latter grows linearly with the wavenumber. The calculated mean drift force on a porous hemisphere and a vertical truncated cylinder, relevant to the construction of fish cages, is compared to available published results.
文摘The paper presents and discusses theoretical bases and methodology of development of two- and three-dimensional analytical and optical isodynes. Atten- tion is given to the theoretical admissibility of the major components of the physical and mathematical models which are taken as the theoretical basis of the isodynes, and of the related analytical and experimental procedures of stress analysis. Efficiency and reliability of the nondestructive isodyne stress analysis are discussed.
基金Project supported by the National Natural Science Foundation of China (Nos. 10772107,10702038,and 11172163)the E-Institutes of Shanghai Municipal Education Commission,and the Shanghai Program for Innovative Research Team in Universities
文摘The ultra-sonic gas atomization （USGA） nozzle is an important apparatus in the metal liquid air-blast atomization process. It can generate oscillating supersonic gas effiux, which is proved to be effective to enforce the atomization and produce narrow-band particle distributions. A double-actuator ultra-sonic gas nozzle is proposed in the present paper by joining up two active signals at the ends of the resonance tubes. Numerical sim- ulations axe adopted to study the effects of the flow development on the acoustic resonant properties inside the Haxtmann resonance cavity with/without actuators. Comparisons show that the strength and the onset process of oscillation are enhanced remarkably with the actuators. The multiple oscillating amplitude peaks are found on the response curves, and two kinds of typical behaviors, i.e., the Hartmann mode and the global mode, are discussed for the corresponding frequencies. The results for two driving actuators are also investigated. When the amplitudes, the frequencies, or the phase difference of the input signals of the actuators are changed, the oscillating amplitudes of gas effiux can be altered effectively.
文摘Active geological and young faulted zones have made Iran's territory one of the most seismological active areas in the world according to recent historical earthquakes.Some of the deadliest earthquakes such as Gilan 1990 and Kermanshah 2018 caused tens of thousands fatalities.If such violent earthquakes affect strategical structures of a country,indirect losses would be more concerning than direct losses.Nowadays there is no doubt about the vital role of tunnels and underground structures in urban areas.These facilities serve as nonstop functional structures for human transportation,water and sewage systems and underground pedestrian ways.Any external hazard subjected to underground spaces,such as earthquake could directly affect passenger's lives and significantly decrease whole system reliability of public transportation.Commonly two earthquake levels of intensities,Maximum Design Earthquake(MDE)and Operating Design Earthquake(ODE)were used in seismic design of underground structures.However,uncertain nature of earthquakes in terms of frequency content,duration of strong ground motion,and level of intensity indicate that only the two levels of earthquake(ODE and MDE)cannot cover the all range of possible seismic responses of structures during a probable earthquake.It is important to evaluate the behavior of tunnel under a wide range of earthquake intensities.For this purpose,a practical risk-based approach which is obtained using the total probability rule was used.This study illustrates a framework for evaluation seismic stability of tunnels.Urban railway tunnels of Tehran,Shiraz,Ahwaz,Mashhad,Isfahan and Tabriz were considered as study cases.Nominal value of seismic risk for three main damage states,including minor,moderate and major were calculated.
基金Project supported by the National Natural Science Foundation of China(Nos.11372175 and 11272197)the Doctoral Fund of Ministry of Education of China(No.20103108110004)the Innovation Program of Shanghai Municipality Education Commission(No.14ZZ095)
文摘The structures of water inside and outside （6,6）, （8,8）, and （10,10） single- walled carbon nanotubes （SWCNTs） under an electric field perpendicular to the tube axis are investigated by molecular dynamics simulations. The results show that dipole reorientation induced by electric field plays a significant role on the structures of confined water inside and outside SWCNTs. Inside SWCNTs, the average water occupancy and the average number of hydrogen bonds （H-bonds） per water molecule decrease as the electric intensity increases. Because the field intensity is sufficiently strong, the initial water structures inside the SWCNTs are destroyed, and the isolated water clusters are found. Outside SWCNTs, the azimuthal distributions of the density and the average number of H-bonds per water molecule around the solid walls become more and more asymmetric as the electric intensity increases. The percentages of water molecules involved in 0-5 H-bonds for all the three types of SWCNTs under different field intensities are displayed. The results show that those water molecules involved with most H-bonds are the most important to hold the original structures. When the electric field direction is parallel with the original preferred orientation, the density and the H-bond connections in water will be increased; when the electric field direction is perpendicular to the original preferred orientation, the density and the H-bond connections in water will be decreased.
基金Project supported by the National Natural Science Foundation of China(Nos.11372175 and 11272197)the Research Fund for the Doctoral Program of Higher Education of China(No.20103108110004)the Innovation Program of Shanghai Municipality Education Commission(No.14ZZ095)
文摘The molecular dynamics simulations are performed to show that in aque- ous environments, a short single-walled carbon nanotube （SWCNT） guided by a long SWCNT, either inside or outside the longer tube, is capable of moving along the nanotube axis unidirectionally in an electric field perpendicular to the carbon nanotube （CNT） axis with the linear gradient. The design suggests a new way of molecule transportation or mass delivery. To reveal the mechanism behind this phenomenon, the free energy profiles of the system are calculated by the method of the potential of mean force （PMF）.
基金National Basic Research Program of China(973 Program,No. 2003CB716207)National Natural Science Foundation of China(No.50775091)
文摘A method for measurement of ultra-low flying height in head-disk spacing is described. Three different wavelengths are selected out from white light by filters to measure the spacing simultaneously. Besides solving the ambiguity problem, a more reliable result is achieved by using weighted average of measurement results from three different wavelengths, where the weight is dependent upon spacing. Fringe-bunching correction algorithm （FBC） and spot-tilling technique are adopted to suppress calibration and random errors. Moreover, incident bandwidth correction （IBC） method is introduced to compensate the error caused by low monochromaticity of incident light. Based on dynamic flying height tester （DFHT Ⅱ）, with the redesigned of photo-electric conversion and signal acquirement module, an instrument has been developed. And comparing the experimental data from the instrument with those from a KLA-FHT D6, the discrepancy is less than 5%. It indicates that the instrument is suitable to perform ultra-low flying height measurement and satisfies the reauirement of magnetic heads manufacturing.
文摘For investigation of equilibrium conditions of electrons in an atom, and Ionization Energies of Elements, a simplified deterministic static model is proposed. The electrons are initially uniformly and sparsely arranged on the outer surface of nucleus. Then, by taking into account the nucleus-electron interaction (attractive and repulsive) and the mutual electron-electron repulsions, and by a simple step-by-step nonlinear static analysis program, all the electrons are found to equilibrate on the outer surface of the same sphere, which is concentric and larger than nucleus. In a second stage, starting from an equilibrium sphere of electrons, one of the electrons is subjected to gradual forced removal, radially and outwards with respect to nucleus. Within each removal step, the produced work increment is determined and the increments are summed. When no more significant attraction is exerted by nucleus to removed electron, the total work gives the Ionization Energy. After removing of single electron, the remaining electrons fall on a lower shell, that is, they equilibrate on the outer surface of a smaller concentric sphere. For nucleus-electron interaction, an L-J (Lennard-Jones) type curve, attractive and repulsive, is adopted. When the parameter of this curve is n > 1.0, the Ionization Energy exhibits an upper bound. As parameter n increases from 1.0 up to 2.0, the attractive potential of L-J curve is gradually weakened. The proposed model is applied on Argon. It is observed that, as the number of electrons increases, the radius of equilibrium sphere increases, too, whereas the attractive nucleus-electron potential is reduced;thus the Ionization Energy is reduced, too. Particularly, as the number of electrons and the radius of equilibrium sphere exceed some critical values, the above two last quantities exhibit abrupt falls. A regular polyhedron is revealed, which can accommodate Elements up to atomic number Z = 146, that is 28 more than Z = 118 of existing last Element, as guide for initial locations of electrons in the above first program.
基金supports from the National Natural Science Foundation of China(No.52101151)the Hong Kong Research Grant Council(RGC)(Grant No.CityU 21205621 and C1020-21G)+1 种基金the Shenzhen Science and Technology Program(Grant No.SGDX20210823104002016)the Harbin Institute of Technology(Shenzhen)thanks to thefinancial support from the National Natural Science Foundation of China(No.52101135)and the Shenzhen Science and Technology Program(Grant No.RCBS20210609103202012).
文摘Nanoprecipitation strengthening has been widely adopted as an effective way to design high-strength alloys,which generally leads to the loss of ductility. Here we unveil the unique bifunctionality of L12-structurednanoprecipitates in a FeCoNiAlTi-type high entropy alloy , enabling the combined increase of tensile strength andductility. Results show that as-quenched precipitate-free matrix alloys undergo thermally-induced martensitetransformation and form the body-centered cubic martensite phase with limited tensile ductility. In strongcontrast, when introducing the dense coherent L12-type nanoprecipitates, the face-centered cubic matrix istemporarily stabilized, which in turn promotes the microbands-induced plasticity associated with stress-inducedmartensite transformation upon deformation. This allows us to achieve significantly improved work hardeningcapability and excellent plastic deformation stability at a high-strength level. These new findings reshape ourunderstanding of the precipitation strengthening and could provide useful guidance for developing highperformance alloys by regulating the coherent nanoprecipitate and martensitic phase transformation.
文摘Electromagnetic forming is a high-speed forming technology by which hollow profiles can be compressed or expanded. It is done with a pulsed magnetic field to apply Lorentz’ forces at electrically conductive material. Electromagnetic hollow tube expansion is limited by the fragmentation tendency. This work attempts to use a combination of analytical and computational approach to compute the net tangential stress during tube expansion. A simplified analytical framework to estimate the temporal evolution of plastic stresses present in aluminium alloy AA5052 at low and high applied magnetic pressures is developed based upon dynamic imaging. The time resolved images captured using current synchronised high speed camera record the overall dimensional changes of the tube that is validated by multi-physics simulation of expansion process. Imaging of hollow tube expansions at two selected peak currents has been carried out at various current levels in the range 76 - 160 kA. The direct visualisation of the increase in the tube diameter at two current levels provided a comparison of the developing net tangential stresses in the hollow tube during the undamaged and fragmented expansion. Imaging of tube expansion also facilitates the estimation of the strain rate experienced by the tube and was in the range of ~1700 s<sup>-1</sup> to ~1200 s<sup>-1</sup>. The propensity of fragmentation was found to be due to the level and duration of generated tangential stresses above the yield stress during expansion of the aluminium tubes. Presented study provides a mean of exploiting the enhanced formability of aluminium alloys using electromagnetic forming.
文摘This work reports the successful outcomes to process the polyester, acrylic and wool fiber along with jute fiber exclusively using existing jute processing machineries for manufacturing the 241 tex jute blended yarn. The blending was performed at feeding stage of breaker carding machine and blending ratio of jute and polyester/acrylic/wool fibers is 80:20. Manufacturing of jute blended yarns will create a new opportunity for extending the uses of jute fibers in value added jute products. The present work is concerned with the investigation of physical properties such as tenacity, elongation % at break, quality ratio, unevenness, imperfections (thick, thin & neps) and hairiness of manufactured jute blended yarns. The jute-polyester (80/20) blended yarn shows the higher strength and more evenness compared to jute-acrylic (80/20), jute-wool (80/20) blended and 100% jute yarn.
基金supported by the National Natural Science Foundation of China(32371999)Science and Technology Program of Yulin City,China(2023-CXY-183)+1 种基金Open Project of Key Laboratory of Agricultural Equipment for Hilly and Mountainous Areas in Southeastern China(Co-construction by Ministry and Province),Ministry of Agriculture and Rural Affairs,China(QSKF2023002)National Foreign Expert Project,Ministry of Science and Technology,China(QN2022172006L,DL2022172003L).
文摘Accurate watermelon yield estimation is crucial to the agricultural value chain,as it guides the allocation of agricultural resources as well as facilitates inventory and logistics planning.The conventional method of watermelon yield estimation relies heavily onmanual labor,which is both time-consuming and labor-intensive.To address this,this work proposes an algorithmic pipeline that utilizes unmanned aerial vehicle(UAV)videos for detection and counting of watermelons.This pipeline uses You Only Look Once version 8 s(YOLOv8s)with panorama stitching and overlap partitioning,which facilitates the overall number estimation ofwatermelons in field.The watermelon detection model,based on YOLOv8s and obtained using transfer learning,achieved a detection accuracy of 99.20%,demonstrating its potential for application in yield estimation.The panorama stitching and overlap partitioning based detection and counting method uses panoramic images as input and effectively mitigates the duplications comparedwith the video tracking based detection and countingmethod.The counting accuracy reached over 96.61%,proving a promising application for yield estimation.The high accuracy demonstrates the feasibility of applying this method for overall yield estimation in large watermelon fields.
文摘A theoretical model is developed to predict the upper limit heat transfer between a stack of parallel plates subject to multiphase cooling by air-mist flow.The model predicts the optimal separation distance between the plates based on the development of the boundary layers for small and large separation distances,and for dilute mist conditions.Simulation results show the optimal separation distance to be strongly dependent on the liquid-to-air mass flow rate loading ratio,and reach a limit for a critical loading.For these dilute spray conditions,complete evaporation of the droplets takes place.Simulation results also show the optimal separation distance decreases with the increase in the mist flow rate.The proposed theoretical model shall lead to a better understanding of the design of fins spacing in heat exchangers where multiphase spray cooling is used.
文摘A Euler-Lagrangian simulation was employed for a comprehensive parameter study of wood gasification in a fluidized charcoal bed. The parameters that were varied include the initial bed temperature, fuel mass flow rate, inert tar fraction, and kinetic energy losses caused by particle-particle and particle-wall colli- sions. The results of each parameter variation are compared with a base scenario, previously described in detail in Part I of this study （Gerber ＆ Oevermann, 2014）. The results are interpreted by comparing the reactor outlet temperature, averaged particle temperature, overall wood mass, overall charcoal mass, concentrations of several gaseous species, and axial barycenter data for particles obtained with differ- ent sets of parameters. The inert tar fraction and fuel mass flow rate are the most sensitive parameter, while the particle-particle and particle-wall contact parameters have only a small impact on the results. Increasing the reactive tar components by 19% almost doubled the amount of reactive tars at the reac- tor outlet, while decreasing the restitution coefficients of the particle collisions by 0.2 results in higher overall gas production but almost no change in bed height. Herein, our numerical results are discussed in detail while assessing the model restrictions.
文摘Statistical analysis of pressure fluctuations in spouted beds has been used as a well-established diagnostic tool to determine bed and flow characteristics because of its smooth operation. However, in many recent and conventional applications of spouted beds such as drying, coal gasification, catalytic conversion, biomass treatment, and chemical vapor deposition, direct estimation of the heat transfer rate from the solid bed to the gas or vice versa has proven to be difficult. A variance and spectral analysis of pressure fluctuation is extended here to characterize the heat transfer phenomena in a spouted bed. In the present study, zirconia and alumina were used as the bed materials, and argon and nitrogen were used as the spouting gases. Experiments were conducted at various heating rates for different superficial gas velocities for a range of temperatures up to 300 °C. Significant changes in the gas density and viscosity with different extents of heat transfer were observed to affect the momentum diffusivity and gas–particle interaction, which in turn led to local pressure fluctuations, causing the bed to behave differently. In the present work, a novel approach is proposed to establish a link between local pressure fluctuation and the extent of heat transfer in the bed. This method shows potential for correlation of the statistics of pressure fluctuation with the thermal properties of individual solids and gases. Thus, the technique can be extended to many industrial applications for the indirect estimation of the extent of heat transfer and prediction of unknown thermal properties of products in solids or gases.
