Rice is a well-recognized accumulator of arsenic(As),which poses a threat to food security and human health.Different rice varieties vary widely in their As accumulation and tolerance,yet the underlying genetic basis ...Rice is a well-recognized accumulator of arsenic(As),which poses a threat to food security and human health.Different rice varieties vary widely in their As accumulation and tolerance,yet the underlying genetic basis remains unknown.In this study,we isolated a rice mutant hag1,which displayed high accumulation of As in rice grains and increased sensitivity to As toxicity.Using genetic investigation,we identified the ATP-binding cassette(ABC)transporter OsABCC1,involved in sequestering As in vacuoles,as the causal gene responsible for As allocation and tolerance in rice.Detailed physiological analysis revealed that As stress caused more severe oxidative damage in hag1 compared with the wild type(WT).The hag1 mutant displayed different accumulation patterns depending on the levels of As stress.We discovered that under low As concentration,hag1 synthesized more thiol compounds and exhibited lower As translocation than the WT;however,at high As levels,hag1 produced fewer thiol compounds and increased As transfer factor.Transcriptome analysis of the node nearest to the panicles revealed that OsABCC1 was down-regulated in hag1,resulting in increased As translocation and accumulation in rice grains.Additionally,natural variations in the promoter of OsABCC1 may confer differential gene expression and distinct As accumulations in grains between japonica and indica rice varieties,providing insights for breeding low-As rice varieties.展开更多
The dynamic mechanical response and deformation mechanism of magnesium-yttrium alloy at high strain rate were investigated using split-Hopkinson pressure bar(SHPB)impact,and the microstructure evolution and crack form...The dynamic mechanical response and deformation mechanism of magnesium-yttrium alloy at high strain rate were investigated using split-Hopkinson pressure bar(SHPB)impact,and the microstructure evolution and crack formation mechanism were revealed.The yield strength and work hardening rate increase significantly with increasing impact strain rate.Deformation twinning and non-basal dislocation slip are the primary deformation mechanisms during testing.Contrary to crack initiation mechanism facilitated by adiabatic shear bands,we find that high-density co-axial nanocrystalline grains form near cracks,which leads to local softening and promotes crack initiation and rapid propagation.Most grains have similar<1^(-)21^(-)0>orientations,with unique misorientation of 24°,32°,62°,78°and 90°between adjacent grains,suggesting that these grains are primarily formed by interface transformation,which exhibits distinct differences from recrystallized grains.Our results shed light upon the dynamic mechanical response and crack formation mechanism in magnesium alloys under impact deformation.展开更多
Ultra-fine austenite grains with size of i-3 μm were prepared in a Nb-V-Ti steel through repetitive treatment of rapid heating and quenching. A model for the growth kinetics of these ultra-fine austenite grains was s...Ultra-fine austenite grains with size of i-3 μm were prepared in a Nb-V-Ti steel through repetitive treatment of rapid heating and quenching. A model for the growth kinetics of these ultra-fine austenite grains was successfully created through successive 2 processes, and the activation energy Q for growth was estimated to be about 693.2 kJ/mol, which directly shows the inhibition effect of microalloy elements on the growth of ultra-fine austenite grains.展开更多
By careful design of rolling schedule,ultra-fine （～2μm） ferrite grains in a low carbon high niobium （0.09wt%Nb） microalloying steel with average austenite grain sizes above 800 μm can be achieved in the simulat...By careful design of rolling schedule,ultra-fine （～2μm） ferrite grains in a low carbon high niobium （0.09wt%Nb） microalloying steel with average austenite grain sizes above 800 μm can be achieved in the simulated thin slab direct rolling process. The 5-pass deformation was divided into two stages： the refinement of austenite through complete recrystallization and the refinement of ferrite through dynamic strain-induced transformation. The effects of Nb in solution and strain-induced NbCN precipitates on the ferrite transformation were also extensively discussed.展开更多
The ultra-fine structured Ni?Al?WC layer with interlocking bonding was fabricated on austenitic stainless steel by combination of laser clad and friction stir processing (FSP). Laser was initially applied to Ni?Al ele...The ultra-fine structured Ni?Al?WC layer with interlocking bonding was fabricated on austenitic stainless steel by combination of laser clad and friction stir processing (FSP). Laser was initially applied to Ni?Al elemental powder preplaced on the austenitic stainless steel substrate to produce a coating for further processing. The as-received coating was subjected to FSP treatment, processed by a rotary tool rod made of WC?Co alloy, to obtain sample for inspection. Microstructure, phase constitutions, hardness and wear property were investigated by methods of scanning electronic microscopy (SEM) with energy-dispersive X-ray spectroscopy (EDX) microanalysis, and X-ray diffraction (XRD), hardness test alongside with dry sliding wear test. The results show that the severe deformation effect exerted on the specimen resulted in an ultra-fine grain layer of about 100μmin thickness and grain size of 1?2μm. Synergy between introduction of WC particles to the deformation layer and deformation strengthening contributes greatly to the increase in hardness and friction resistance. An interlocking bonding between the coating and matrix which significantly improves bonding strength was formed due to the severe deformation effect.展开更多
Pure tungsten, oxide dispersion strengthened tungsten and carbide dispersion strengthened tungsten were fabricated by high-energy ball milling and spark plasma sintering process. In order to evaluate the properties of...Pure tungsten, oxide dispersion strengthened tungsten and carbide dispersion strengthened tungsten were fabricated by high-energy ball milling and spark plasma sintering process. In order to evaluate the properties of the tungsten alloys under transient high heat flues, four tungsten samples with different grain sizes were tested by high-intensity pulsed ion beam with a heat flux as high as 160 MW/（m^2·s^-1/2）. Compared with the commercial tungsten, the surface modification of the oxide dispersion strengthened tungsten by high-intensity pulsed ion beam is completely different. The oxide dispersion strengthened tungsten shows inferior thermal shock response due to the low melting point second phase of Ti and Y2O3, which results in the surface melting, boiling bubbles and cracking. While the carbide dispersion strengthened tungsten shows better thermal shock response than the commercial tungsten.展开更多
A new processing method,equal channel angular pressing(ECAP)plus cold rolling(CR),was applied to producing ultra-fine grained FeCoV alloy.The microstructures of ultra-fine grained FeCoV alloy after ECAP,ECAP plus CR,a...A new processing method,equal channel angular pressing(ECAP)plus cold rolling(CR),was applied to producing ultra-fine grained FeCoV alloy.The microstructures of ultra-fine grained FeCoV alloy after ECAP,ECAP plus CR,and the effect of tempering treatment on the microstructure of FeCoV alloy produced by ECAP plus CR were investigated.The results show that an elongated substructure with a width of about 0.3μm is obtained after four-pass ECAP using Route A.Cold rolling after ECAP cannot change the morphologies of elongated substructure,and it results in higher fraction of high-angle boundaries and higher dislocation density compared with the identical ECAP without rolling.Subsequent tempering for 30 min at 853 K brings about many nano-phases precipitating at subgrain boundaries and insides the grains,and the size of precipitated phase is measured to be about 10 nm.Nano-phases grow up with increasing tempering temperature and equiaxed structure forms at 883 K.展开更多
Contrast tests were carried out to study the fatigue performance of the butt joints treated by ultrasonic peening, aiming at the improvement of ultrasonic peening treatment(UPT) on welded joints of a new material. The...Contrast tests were carried out to study the fatigue performance of the butt joints treated by ultrasonic peening, aiming at the improvement of ultrasonic peening treatment(UPT) on welded joints of a new material. The material is a new generation of fine grain and high purity SS400 steel that has the same ingredients as the traditional low carbon steel. The specimens are in two different states:welded and ultrasonic peening conditions. The corresponding fatigue testing data were analyzed according to the regulation of the statistical method for fatigue life of the welded joints established by International Institute of Welding(IIW). Welding residual stress was considered in two different ways: the constant stress ratio R=0.5 and the Ohta method. The nominal stress-number (σ-N)curves were corrected because of the different plate thickness compared to the standard and because there was no mismatch or angular deformation. The results indicated that: 1) Compared with the welded specimens, when the stress range was 200 MPa, the fatigue life of the SS400 steel specimens treated by ultrasonic peening is prolonged by over 58 times, and the fatigue strength FAT corresponding to 106 cycles is increased by about 66%; 2) As for the SS400 butt joint (single side welding double sides molding), after being treated by UPT, the nominal S-N curve (m=10) of FAT 100 MPa(R=0.5) should be used for fatigue design. The standard S-N curves of FAT 100 MPa(R=0.5, m=10) could be used for fatigue design of the SS400 steel butt joints treated by ultrasonic peening.展开更多
In this essay, we studied how heat input affected the microstructure, hardness, grain size and heat-affected zone(HAZ) dimension of WCX355 ultra-fine grain steel which was welded respectively by the ultra narrow-gap w...In this essay, we studied how heat input affected the microstructure, hardness, grain size and heat-affected zone(HAZ) dimension of WCX355 ultra-fine grain steel which was welded respectively by the ultra narrow-gap welding (UNGW) process and the overlaying process with CO 2 as protective atmosphere and laser welding process. The experimental results show when the heat input changed from 1.65 kJ/cm to 5.93 kJ/cm, the width of its HAZ ranged from 0.6 mm to 2.1 mm.The average grain size grew up from 2～5 μm of base metal to 20～70 μm and found no obvious soften phenomenon in overheated zone. The width of normalized zone was generally wide as 2/3 as that of the whole HAZ, and the grain size in this zone is smaller than that in base metal. Under the circumstance of equal heat input, the HAZ width of UNGW is narrower than that of the laser welding.展开更多
Experiments were conducted to evaluate the grain refinement and thermal stability of ultra-fine grained Al-4Mgalloy introduced by equal-channel angular pressing (ECAP) at 473 K. The results show that the intensities o...Experiments were conducted to evaluate the grain refinement and thermal stability of ultra-fine grained Al-4Mgalloy introduced by equal-channel angular pressing (ECAP) at 473 K. The results show that the intensities of X-ray(111/222) and (200/400) peaks for the alloy processed by ECAP decrease significantly and the peak widths of halfheight become broadening compared with the corresponding value in the annealed alloy. The microstructure of 2passes ECAPed alloy consists of both elongated and equiaxed subgrains. The residual strain in the alloy increaseswith increasing passes numbers, that appears as increasing dislocation density and lattice constant of matrix. Anequiaxed ultra-fine grained structure of～0.2μm is obtained in the present alloy after 8 passes. The ultra-fine grainsare stable below 523 K, because the alloy retains extremely fine grain size of～1μm after static annealing at 523 Kfor 1 h.展开更多
The ultra-fine grain （UFG） steel is welded by using resistance spot welding technique with or without requirement of upsetting force. Metallographic inspection shows that the grain size of weld nugget is larger than...The ultra-fine grain （UFG） steel is welded by using resistance spot welding technique with or without requirement of upsetting force. Metallographic inspection shows that the grain size of weld nugget is larger than that of the base metal and the microstructure is altered significantly. In addition, contracting defects such as air holes can be found in the nugget center. The experiments show that the defects can be effectively avoided by the technique of adding upsetting force during the nugget cooling and crystallizing processes. In tensile shear tests, the welding joint starts to crack from the inner edge of the corona bond. The results of micro-hardness tests show that the newly born martensite structure dramatically improves the hardness of the joint. Under the interactions between residual stresses and regenerated fine grains, the micro-hardness of the heat-affected zone （ HAZ ） is lower than that of the nugget, but evidently higher than that of the base metal.展开更多
Grain yield is determined mainly by grain number and grain weight.In this study,we identified and characterized MORE GRAINS1(MOG1),a gene associated with grain number and grain weight in rice(Oryza sativa L.),through ...Grain yield is determined mainly by grain number and grain weight.In this study,we identified and characterized MORE GRAINS1(MOG1),a gene associated with grain number and grain weight in rice(Oryza sativa L.),through map-based cloning.Overexpression of MOG1 increased grain yield by 18.6%-22.3%under field conditions.We determined that MOG1,a bHLH transcription factor,interacts with OsbHLH107 and directly activates the expression of LONELY GUY(LOG),which encodes a cytokinin-activating enzyme and the cell expansion gene EXPANSIN-LIKE1(EXPLA1),positively regulating grain number per panicle and grain weight.Natural variations in the promoter and coding regions of MOG1 between Hap-LNW and Hap-HNW alleles resulted in changes in MOG1 expression level and transcriptional activation,leading to functional differences.Haplotype analysis revealed that Hap-HNW,which results in a greater number and heavier grains,has undergone strong selection but has been poorly utilized in modern lowland rice breeding.In summary,the MOG1-OsbHLH107 complex activates LOG and EXPLA1 expression to promote cell expansion and division of young panicles through the cytokinin pathway,thereby increasing grain number and grain weight.These findings suggest that Hap-HNW could be used in strategies to breed high-yielding temperate japonica lowland rice.展开更多
The ultra-fine grained(UFG)pure titanium was prepared by equal channel angular pressing(ECAP)and rotary swaging(RS).The strain controlled low cycle fatigue(LCF)test was carried out at room temperature.The fatigue life...The ultra-fine grained(UFG)pure titanium was prepared by equal channel angular pressing(ECAP)and rotary swaging(RS).The strain controlled low cycle fatigue(LCF)test was carried out at room temperature.The fatigue life prediction model and mean stress relaxation model under asymmetrical stress load were discussed.The results show that the strain ratio has a significant effect on the low cycle fatigue performance of the UFG pure titanium,and the traditional Manson-coffin model can not accurately predict the fatigue life under asymmetric stress load.Therefore,the SWT mean stress correction model and three-parameter power curve model are proposed,and the test results are verified.The final research shows that the threeparameter power surface model has better representation.By studying the mean stress relaxation phenomenon under the condition of R≠-1,it is revealed that the stress ratio and the strain amplitude are the factors that significantly afiect the mean stress relaxation rate,and the mean stress relaxation model with the two variables is calculated to describe the mean stress relaxation phenomenon of the UFG pure titanium under different strain ratios.The fracture morphology of the samples was observed by SEM,and it was concluded that the final fracture zone of the fatigue fracture of the UFG pure titanium was a mixture of ductile fracture and quasi cleavage fracture.The toughness of the material increases with the increase of strain ratio at the same strain amplitude.展开更多
Tests of the candidate plasma facing materials（PFMs） used in experimental fusion devices are essential due to the direct influence of in-situ plasma loading.A type of ultrafine grained（UFG） tungsten sintered by re...Tests of the candidate plasma facing materials（PFMs） used in experimental fusion devices are essential due to the direct influence of in-situ plasma loading.A type of ultrafine grained（UFG） tungsten sintered by resistance sintering under ultra-high pressure（RSUHP） method has been exposed in the edge plasma of the HT-7 tokamak to investigate its performance under plasma loading.Under cychc edge plasma loading,the UFG tungsten develops both macro and micro cracks.The macro cracks are attributed to the low temperature brittleness of the tungsten material itself,while the micro cracks are generated from local intense power flux deposition.展开更多
This study aims to investigate grain quality and nutritional values of rice(Pokkali,a salt-tolerant cultivar;RD73,a new cultivar improved from KDML105 introgressed with Saltol QTL from Pokkali,and KDML105,a moderately...This study aims to investigate grain quality and nutritional values of rice(Pokkali,a salt-tolerant cultivar;RD73,a new cultivar improved from KDML105 introgressed with Saltol QTL from Pokkali,and KDML105,a moderately salt-susceptible cultivar)grown under non-saline(0.04–0.87 dS/m)and slightly saline(1.08–4.83 dS/m)field conditions.The results revealed that salinity caused significant reduction in grain size but significant increments in reducing sugar and total protein contents in the grains.Nevertheless,the amounts of starch in the grains of KDML105 and Pokkali rice genotypes were unaffected by the stress.The starch granule size distribution was also unaffected by salinity.Interestingly,only starch from Pokkali was significantly diminished in amylose content,from 19.18%to 16.99%.Accordingly,parameters relating to starch gelatinization,retrogradation,and pasting properties of KDML105 and RD73 were unaffected by salinity;only Pokkali showed a significant increase in percentage of retrogradation along with a significant reduction in gelatinization enthalpy.In the saline field,total phenolic content and antioxidant capacity in the grains of all rice cultivars tended to increase,particularly in Pokkali.On average,essential element contents in grains from the saline-treated plants showed a 33%,32%,32%,22%,20%,11%,and 10%increase in total P,N,K,Mg,Zn,Fe,and Ca content,respectively.Interestingly,total Fe content exhibited the greatest percentage of increments in KDML105(187%).Taken together,cultivation of rice in the slightly saline field did not alter its eating and cooking qualities,while enhanced some nutritional properties such as proteins,minerals,and secondary metabolites like phenolic compounds.展开更多
The critical crack dimensions of both base-metal specimen and HAZ specimen are measured via wide-plate tensile tests. Based on the “fitness for purpose” principle, the fracture behavior of the ultra-fine grain steel...The critical crack dimensions of both base-metal specimen and HAZ specimen are measured via wide-plate tensile tests. Based on the “fitness for purpose” principle, the fracture behavior of the ultra-fine grain steel SS400 welded joint HAZ is assessed. The test results indicate that overmatching is benefit for the whole capability’s improvement of ultra-fine grain steel SS400. The test results are confirmed by using finite element method (FEM).展开更多
The changes in austenite grain size of the specimens with coarse ferrite grains under different heat treatment process were investigated.The focus was on studying the effect of annealing on refining coarse ferrite gra...The changes in austenite grain size of the specimens with coarse ferrite grains under different heat treatment process were investigated.The focus was on studying the effect of annealing on refining coarse ferrite grains,as well as the influence of the ferrite grain size on the main technical indicators of gas carburizing.The results show that coarse ferrite grains may not necessarily cause the coarse austenite grains,but may result in mixed austenite grains.After annealing treatment,the coarse ferrite grains can be significantly refined and homogenized.Moreover,the coarse ferrite grains have no significant effects on hardnessand intergranular oxidationof gas carburizing.展开更多
New flat-oval groove rolling process of multi-direction deformation is proposed to manufacture ultra-fine grain bar. Application of new groove series can introduce uniform large plastic strain into whole cross section...New flat-oval groove rolling process of multi-direction deformation is proposed to manufacture ultra-fine grain bar. Application of new groove series can introduce uniform large plastic strain into whole cross section of the material, and meanwhile satisfy the requirements of shape and size. Principle of grain refinement, based on experimental research of small specimen, is that grain refinement of ferrite is mainly dynamic recrystallization when low-carbon alloy steel is at low temperature deformation. Relationship of grain size and z-factor is also obtained through experimental research, as well as ultra-fine ferrite grain less than 1 micron. To predict strain, shape, dimensions and grain size of the material in rolling process, numerical simulation model of the warm groove bar rolling process is established via nonlinear finite element method, and distribution of grain size of the final section is obtained via finite element subroutine. The result indicates that ultra-fine grain bar rolling can accomplish at low temperature region.展开更多
According to the general opinion,grains should occupy the largest amount of human food each day,but this grain-based eating habit does not allow human life to be extended.Grains are high in carbohydrates and five comm...According to the general opinion,grains should occupy the largest amount of human food each day,but this grain-based eating habit does not allow human life to be extended.Grains are high in carbohydrates and five commonly recognized plant hormones,namely auxin,gibberellin,cytokinin,abscisic acid,and ethylene.Through in-depth analysis of ancient books,it was found that five grains for support:support is a restriction,and it means the essence,which means that grains should be eaten less,and it is the essence of the least daily intake.To correctly understand the Chinese dietary concept of"five grains for support"is the basis for improving Asian dietary health and promoting Asian human health.展开更多
The present work focuses mainly on an in vivo evaluation of ultra fine grained titanium （UFG-Ti） obtained by severe plastic deformation （SPD）. The SPD on commercially produced Grade 2 titanium （Cp-Ti） resulted i...The present work focuses mainly on an in vivo evaluation of ultra fine grained titanium （UFG-Ti） obtained by severe plastic deformation （SPD）. The SPD on commercially produced Grade 2 titanium （Cp-Ti） resulted in the refinement of the grain size by several orders of magnitude. Polished surfaces having similar roughness from both UFG-Ti and Cp-Ti were prepared. In vitro test revealed the presence of fibronectin, which was involved in the attachment of the cells to the substrate. Phase contrast micrographs showed the highest signal of fibronectin in UFG-Ti, indicating that it is more cytocompatible than Cp-Ti. In vivo tests, by subcutaneous implantation of the metals in the rats showed the better biocompatibility of UFG-Ti over Cp-Ti. The improved biocompatibility of UFG-Ti was attributed to the presence of surface discontinuities （in the form of nano-defects）, surface energy, higher wettability, surface stress and stable TiO2 films, which increased the protein adsorption on the surface.展开更多
基金supported by the earmarked fund for‘Pioneer’and‘Leading Goose’R&D Program of Zhejiang Province,China(Grant No.2023C02014)the Central Public Interest Scientific Institution Basal Research Fund for the China National Rice Research Institute(Grant No.CPSIBRF-CNRRI-202407).
文摘Rice is a well-recognized accumulator of arsenic(As),which poses a threat to food security and human health.Different rice varieties vary widely in their As accumulation and tolerance,yet the underlying genetic basis remains unknown.In this study,we isolated a rice mutant hag1,which displayed high accumulation of As in rice grains and increased sensitivity to As toxicity.Using genetic investigation,we identified the ATP-binding cassette(ABC)transporter OsABCC1,involved in sequestering As in vacuoles,as the causal gene responsible for As allocation and tolerance in rice.Detailed physiological analysis revealed that As stress caused more severe oxidative damage in hag1 compared with the wild type(WT).The hag1 mutant displayed different accumulation patterns depending on the levels of As stress.We discovered that under low As concentration,hag1 synthesized more thiol compounds and exhibited lower As translocation than the WT;however,at high As levels,hag1 produced fewer thiol compounds and increased As transfer factor.Transcriptome analysis of the node nearest to the panicles revealed that OsABCC1 was down-regulated in hag1,resulting in increased As translocation and accumulation in rice grains.Additionally,natural variations in the promoter of OsABCC1 may confer differential gene expression and distinct As accumulations in grains between japonica and indica rice varieties,providing insights for breeding low-As rice varieties.
基金support from the National Natural Science Foundation of China(Grant Nos.52301137,51974097,52364050)the Natural Science Special Foundation of Guizhou University(No.(2023)20)+1 种基金Guizhou Province Science and Technology Project(Grant Nos.[2023]001,[2019]2163)Guiyang city Science and Technology Project(Grant No.[2023]48-16).
文摘The dynamic mechanical response and deformation mechanism of magnesium-yttrium alloy at high strain rate were investigated using split-Hopkinson pressure bar(SHPB)impact,and the microstructure evolution and crack formation mechanism were revealed.The yield strength and work hardening rate increase significantly with increasing impact strain rate.Deformation twinning and non-basal dislocation slip are the primary deformation mechanisms during testing.Contrary to crack initiation mechanism facilitated by adiabatic shear bands,we find that high-density co-axial nanocrystalline grains form near cracks,which leads to local softening and promotes crack initiation and rapid propagation.Most grains have similar<1^(-)21^(-)0>orientations,with unique misorientation of 24°,32°,62°,78°and 90°between adjacent grains,suggesting that these grains are primarily formed by interface transformation,which exhibits distinct differences from recrystallized grains.Our results shed light upon the dynamic mechanical response and crack formation mechanism in magnesium alloys under impact deformation.
基金supported by the National Natural Science Foundation of China(No.50527402)
文摘Ultra-fine austenite grains with size of i-3 μm were prepared in a Nb-V-Ti steel through repetitive treatment of rapid heating and quenching. A model for the growth kinetics of these ultra-fine austenite grains was successfully created through successive 2 processes, and the activation energy Q for growth was estimated to be about 693.2 kJ/mol, which directly shows the inhibition effect of microalloy elements on the growth of ultra-fine austenite grains.
基金the Major State Basic Research and Development Program of China (No2004CB619102)
文摘By careful design of rolling schedule,ultra-fine （～2μm） ferrite grains in a low carbon high niobium （0.09wt%Nb） microalloying steel with average austenite grain sizes above 800 μm can be achieved in the simulated thin slab direct rolling process. The 5-pass deformation was divided into two stages： the refinement of austenite through complete recrystallization and the refinement of ferrite through dynamic strain-induced transformation. The effects of Nb in solution and strain-induced NbCN precipitates on the ferrite transformation were also extensively discussed.
基金Projects(51571214,51301205,51101126)supported by the National Natural Science Foundation of ChinaProject(P2014-07)supported by the Open Fund of State Key Laboratory of Materials Processing and Die&Mould Technology,China+4 种基金Project(20130162120001)supported by the Specialized Research Fund for the Doctoral Program of Higher Education of ChinaProject(K1308034-11)supported by the Changsha Municipal Science and Technology Plan,ChinaProjects(2015GK3004,2015JC3006)supported by the Science and Technology Project of Hunan Province,ChinaProject supported by the Innovation-driven Plan in Central South University,ChinaProject supported by the Independent Project of State Key Laboratory of Powder Metallurgy of Central South University,China
文摘The ultra-fine structured Ni?Al?WC layer with interlocking bonding was fabricated on austenitic stainless steel by combination of laser clad and friction stir processing (FSP). Laser was initially applied to Ni?Al elemental powder preplaced on the austenitic stainless steel substrate to produce a coating for further processing. The as-received coating was subjected to FSP treatment, processed by a rotary tool rod made of WC?Co alloy, to obtain sample for inspection. Microstructure, phase constitutions, hardness and wear property were investigated by methods of scanning electronic microscopy (SEM) with energy-dispersive X-ray spectroscopy (EDX) microanalysis, and X-ray diffraction (XRD), hardness test alongside with dry sliding wear test. The results show that the severe deformation effect exerted on the specimen resulted in an ultra-fine grain layer of about 100μmin thickness and grain size of 1?2μm. Synergy between introduction of WC particles to the deformation layer and deformation strengthening contributes greatly to the increase in hardness and friction resistance. An interlocking bonding between the coating and matrix which significantly improves bonding strength was formed due to the severe deformation effect.
基金roject (50634060) supported by the National Natural Science Foundation of ChinaProject (2010GB109000) supported by the National Basic Research Program of China
文摘Pure tungsten, oxide dispersion strengthened tungsten and carbide dispersion strengthened tungsten were fabricated by high-energy ball milling and spark plasma sintering process. In order to evaluate the properties of the tungsten alloys under transient high heat flues, four tungsten samples with different grain sizes were tested by high-intensity pulsed ion beam with a heat flux as high as 160 MW/（m^2·s^-1/2）. Compared with the commercial tungsten, the surface modification of the oxide dispersion strengthened tungsten by high-intensity pulsed ion beam is completely different. The oxide dispersion strengthened tungsten shows inferior thermal shock response due to the low melting point second phase of Ti and Y2O3, which results in the surface melting, boiling bubbles and cracking. While the carbide dispersion strengthened tungsten shows better thermal shock response than the commercial tungsten.
基金Project(50675133)supported by the National Natural Science Foundation of ChinaProject(2006CB705401)supported by the National Basic Research Program of China
文摘A new processing method,equal channel angular pressing(ECAP)plus cold rolling(CR),was applied to producing ultra-fine grained FeCoV alloy.The microstructures of ultra-fine grained FeCoV alloy after ECAP,ECAP plus CR,and the effect of tempering treatment on the microstructure of FeCoV alloy produced by ECAP plus CR were investigated.The results show that an elongated substructure with a width of about 0.3μm is obtained after four-pass ECAP using Route A.Cold rolling after ECAP cannot change the morphologies of elongated substructure,and it results in higher fraction of high-angle boundaries and higher dislocation density compared with the identical ECAP without rolling.Subsequent tempering for 30 min at 853 K brings about many nano-phases precipitating at subgrain boundaries and insides the grains,and the size of precipitated phase is measured to be about 10 nm.Nano-phases grow up with increasing tempering temperature and equiaxed structure forms at 883 K.
文摘Contrast tests were carried out to study the fatigue performance of the butt joints treated by ultrasonic peening, aiming at the improvement of ultrasonic peening treatment(UPT) on welded joints of a new material. The material is a new generation of fine grain and high purity SS400 steel that has the same ingredients as the traditional low carbon steel. The specimens are in two different states:welded and ultrasonic peening conditions. The corresponding fatigue testing data were analyzed according to the regulation of the statistical method for fatigue life of the welded joints established by International Institute of Welding(IIW). Welding residual stress was considered in two different ways: the constant stress ratio R=0.5 and the Ohta method. The nominal stress-number (σ-N)curves were corrected because of the different plate thickness compared to the standard and because there was no mismatch or angular deformation. The results indicated that: 1) Compared with the welded specimens, when the stress range was 200 MPa, the fatigue life of the SS400 steel specimens treated by ultrasonic peening is prolonged by over 58 times, and the fatigue strength FAT corresponding to 106 cycles is increased by about 66%; 2) As for the SS400 butt joint (single side welding double sides molding), after being treated by UPT, the nominal S-N curve (m=10) of FAT 100 MPa(R=0.5) should be used for fatigue design. The standard S-N curves of FAT 100 MPa(R=0.5, m=10) could be used for fatigue design of the SS400 steel butt joints treated by ultrasonic peening.
文摘In this essay, we studied how heat input affected the microstructure, hardness, grain size and heat-affected zone(HAZ) dimension of WCX355 ultra-fine grain steel which was welded respectively by the ultra narrow-gap welding (UNGW) process and the overlaying process with CO 2 as protective atmosphere and laser welding process. The experimental results show when the heat input changed from 1.65 kJ/cm to 5.93 kJ/cm, the width of its HAZ ranged from 0.6 mm to 2.1 mm.The average grain size grew up from 2～5 μm of base metal to 20～70 μm and found no obvious soften phenomenon in overheated zone. The width of normalized zone was generally wide as 2/3 as that of the whole HAZ, and the grain size in this zone is smaller than that in base metal. Under the circumstance of equal heat input, the HAZ width of UNGW is narrower than that of the laser welding.
文摘Experiments were conducted to evaluate the grain refinement and thermal stability of ultra-fine grained Al-4Mgalloy introduced by equal-channel angular pressing (ECAP) at 473 K. The results show that the intensities of X-ray(111/222) and (200/400) peaks for the alloy processed by ECAP decrease significantly and the peak widths of halfheight become broadening compared with the corresponding value in the annealed alloy. The microstructure of 2passes ECAPed alloy consists of both elongated and equiaxed subgrains. The residual strain in the alloy increaseswith increasing passes numbers, that appears as increasing dislocation density and lattice constant of matrix. Anequiaxed ultra-fine grained structure of～0.2μm is obtained in the present alloy after 8 passes. The ultra-fine grainsare stable below 523 K, because the alloy retains extremely fine grain size of～1μm after static annealing at 523 Kfor 1 h.
文摘The ultra-fine grain （UFG） steel is welded by using resistance spot welding technique with or without requirement of upsetting force. Metallographic inspection shows that the grain size of weld nugget is larger than that of the base metal and the microstructure is altered significantly. In addition, contracting defects such as air holes can be found in the nugget center. The experiments show that the defects can be effectively avoided by the technique of adding upsetting force during the nugget cooling and crystallizing processes. In tensile shear tests, the welding joint starts to crack from the inner edge of the corona bond. The results of micro-hardness tests show that the newly born martensite structure dramatically improves the hardness of the joint. Under the interactions between residual stresses and regenerated fine grains, the micro-hardness of the heat-affected zone （ HAZ ） is lower than that of the nugget, but evidently higher than that of the base metal.
基金supported by grants from the STI2030 Major Projects(2023ZD0406803)Agro ST Project(NK2022050103)+5 种基金the National Natural Science Foundation of China(32372094,32272123,and 32072036)the Modern Agricultural Industry Technology System Projects of Henan,China(HARS-22-03-G3)the Key R&D projects of Henan(231111110500)the Key Laboratory of Functional Agriculture,Guizhou Province([2023]007)the Key Laboratory of Molecular Breeding for Grain and Oil crops,Guizhou Province([2023]008)the China Postdoctoral Science Foundation(2021M701108).
文摘Grain yield is determined mainly by grain number and grain weight.In this study,we identified and characterized MORE GRAINS1(MOG1),a gene associated with grain number and grain weight in rice(Oryza sativa L.),through map-based cloning.Overexpression of MOG1 increased grain yield by 18.6%-22.3%under field conditions.We determined that MOG1,a bHLH transcription factor,interacts with OsbHLH107 and directly activates the expression of LONELY GUY(LOG),which encodes a cytokinin-activating enzyme and the cell expansion gene EXPANSIN-LIKE1(EXPLA1),positively regulating grain number per panicle and grain weight.Natural variations in the promoter and coding regions of MOG1 between Hap-LNW and Hap-HNW alleles resulted in changes in MOG1 expression level and transcriptional activation,leading to functional differences.Haplotype analysis revealed that Hap-HNW,which results in a greater number and heavier grains,has undergone strong selection but has been poorly utilized in modern lowland rice breeding.In summary,the MOG1-OsbHLH107 complex activates LOG and EXPLA1 expression to promote cell expansion and division of young panicles through the cytokinin pathway,thereby increasing grain number and grain weight.These findings suggest that Hap-HNW could be used in strategies to breed high-yielding temperate japonica lowland rice.
基金Funded by National Natural Science Foundation of China(No.51474170)the Key Laboratory Project of Shaanxi Provincial Department of Education(No.20js075)。
文摘The ultra-fine grained(UFG)pure titanium was prepared by equal channel angular pressing(ECAP)and rotary swaging(RS).The strain controlled low cycle fatigue(LCF)test was carried out at room temperature.The fatigue life prediction model and mean stress relaxation model under asymmetrical stress load were discussed.The results show that the strain ratio has a significant effect on the low cycle fatigue performance of the UFG pure titanium,and the traditional Manson-coffin model can not accurately predict the fatigue life under asymmetric stress load.Therefore,the SWT mean stress correction model and three-parameter power curve model are proposed,and the test results are verified.The final research shows that the threeparameter power surface model has better representation.By studying the mean stress relaxation phenomenon under the condition of R≠-1,it is revealed that the stress ratio and the strain amplitude are the factors that significantly afiect the mean stress relaxation rate,and the mean stress relaxation model with the two variables is calculated to describe the mean stress relaxation phenomenon of the UFG pure titanium under different strain ratios.The fracture morphology of the samples was observed by SEM,and it was concluded that the final fracture zone of the fatigue fracture of the UFG pure titanium was a mixture of ductile fracture and quasi cleavage fracture.The toughness of the material increases with the increase of strain ratio at the same strain amplitude.
基金supported by the Key Project of Chinese Academy of Sciences(No.KJCX2-YW-N35)National Natural Science Foundation of China(No.11175205)
文摘Tests of the candidate plasma facing materials（PFMs） used in experimental fusion devices are essential due to the direct influence of in-situ plasma loading.A type of ultrafine grained（UFG） tungsten sintered by resistance sintering under ultra-high pressure（RSUHP） method has been exposed in the edge plasma of the HT-7 tokamak to investigate its performance under plasma loading.Under cychc edge plasma loading,the UFG tungsten develops both macro and micro cracks.The macro cracks are attributed to the low temperature brittleness of the tungsten material itself,while the micro cracks are generated from local intense power flux deposition.
基金supported by the National Research Council of Thailand(Grant No.NRCT813/2563)the Post-Doctoral Training,Khon Kaen University(Grant No.PD2565-02-02)。
文摘This study aims to investigate grain quality and nutritional values of rice(Pokkali,a salt-tolerant cultivar;RD73,a new cultivar improved from KDML105 introgressed with Saltol QTL from Pokkali,and KDML105,a moderately salt-susceptible cultivar)grown under non-saline(0.04–0.87 dS/m)and slightly saline(1.08–4.83 dS/m)field conditions.The results revealed that salinity caused significant reduction in grain size but significant increments in reducing sugar and total protein contents in the grains.Nevertheless,the amounts of starch in the grains of KDML105 and Pokkali rice genotypes were unaffected by the stress.The starch granule size distribution was also unaffected by salinity.Interestingly,only starch from Pokkali was significantly diminished in amylose content,from 19.18%to 16.99%.Accordingly,parameters relating to starch gelatinization,retrogradation,and pasting properties of KDML105 and RD73 were unaffected by salinity;only Pokkali showed a significant increase in percentage of retrogradation along with a significant reduction in gelatinization enthalpy.In the saline field,total phenolic content and antioxidant capacity in the grains of all rice cultivars tended to increase,particularly in Pokkali.On average,essential element contents in grains from the saline-treated plants showed a 33%,32%,32%,22%,20%,11%,and 10%increase in total P,N,K,Mg,Zn,Fe,and Ca content,respectively.Interestingly,total Fe content exhibited the greatest percentage of increments in KDML105(187%).Taken together,cultivation of rice in the slightly saline field did not alter its eating and cooking qualities,while enhanced some nutritional properties such as proteins,minerals,and secondary metabolites like phenolic compounds.
文摘The critical crack dimensions of both base-metal specimen and HAZ specimen are measured via wide-plate tensile tests. Based on the “fitness for purpose” principle, the fracture behavior of the ultra-fine grain steel SS400 welded joint HAZ is assessed. The test results indicate that overmatching is benefit for the whole capability’s improvement of ultra-fine grain steel SS400. The test results are confirmed by using finite element method (FEM).
基金the Shaanxi Innovation Talent Promotion Plan-Youth Science and Technology New Star Project(Talent).Project No.:2023KJXX-121。
文摘The changes in austenite grain size of the specimens with coarse ferrite grains under different heat treatment process were investigated.The focus was on studying the effect of annealing on refining coarse ferrite grains,as well as the influence of the ferrite grain size on the main technical indicators of gas carburizing.The results show that coarse ferrite grains may not necessarily cause the coarse austenite grains,but may result in mixed austenite grains.After annealing treatment,the coarse ferrite grains can be significantly refined and homogenized.Moreover,the coarse ferrite grains have no significant effects on hardnessand intergranular oxidationof gas carburizing.
文摘New flat-oval groove rolling process of multi-direction deformation is proposed to manufacture ultra-fine grain bar. Application of new groove series can introduce uniform large plastic strain into whole cross section of the material, and meanwhile satisfy the requirements of shape and size. Principle of grain refinement, based on experimental research of small specimen, is that grain refinement of ferrite is mainly dynamic recrystallization when low-carbon alloy steel is at low temperature deformation. Relationship of grain size and z-factor is also obtained through experimental research, as well as ultra-fine ferrite grain less than 1 micron. To predict strain, shape, dimensions and grain size of the material in rolling process, numerical simulation model of the warm groove bar rolling process is established via nonlinear finite element method, and distribution of grain size of the final section is obtained via finite element subroutine. The result indicates that ultra-fine grain bar rolling can accomplish at low temperature region.
基金supported by the Krirk University Science Foundation for Young Scholars:2022(107).
文摘According to the general opinion,grains should occupy the largest amount of human food each day,but this grain-based eating habit does not allow human life to be extended.Grains are high in carbohydrates and five commonly recognized plant hormones,namely auxin,gibberellin,cytokinin,abscisic acid,and ethylene.Through in-depth analysis of ancient books,it was found that five grains for support:support is a restriction,and it means the essence,which means that grains should be eaten less,and it is the essence of the least daily intake.To correctly understand the Chinese dietary concept of"five grains for support"is the basis for improving Asian dietary health and promoting Asian human health.
文摘The present work focuses mainly on an in vivo evaluation of ultra fine grained titanium （UFG-Ti） obtained by severe plastic deformation （SPD）. The SPD on commercially produced Grade 2 titanium （Cp-Ti） resulted in the refinement of the grain size by several orders of magnitude. Polished surfaces having similar roughness from both UFG-Ti and Cp-Ti were prepared. In vitro test revealed the presence of fibronectin, which was involved in the attachment of the cells to the substrate. Phase contrast micrographs showed the highest signal of fibronectin in UFG-Ti, indicating that it is more cytocompatible than Cp-Ti. In vivo tests, by subcutaneous implantation of the metals in the rats showed the better biocompatibility of UFG-Ti over Cp-Ti. The improved biocompatibility of UFG-Ti was attributed to the presence of surface discontinuities （in the form of nano-defects）, surface energy, higher wettability, surface stress and stable TiO2 films, which increased the protein adsorption on the surface.
