Microstructure,texture,and mechanical properties of the extruded Mg-2.49Nd-1.82Gd-0.2Zn-0.2Zr alloy were investigated at different extrusion temperatures(260 and 320℃),extrusion ratios(10:1,15:1,and 30:1),and extrusi...Microstructure,texture,and mechanical properties of the extruded Mg-2.49Nd-1.82Gd-0.2Zn-0.2Zr alloy were investigated at different extrusion temperatures(260 and 320℃),extrusion ratios(10:1,15:1,and 30:1),and extrusion speeds(3 and 6 mm/s).The experimental results exhibited that the grain sizes after extrusion were much finer than that of the homogenized alloy,and the second phase showed streamline distribution along the extrusion direction(ED).With extrusion temperature increased from 260 to 320℃,the microstructure,texture,and mechanical properties of alloys changed slightly.The dynamic recrystallization(DRX)degree and grain sizes enhanced as the extrusion ratio increased from 10:1 to 30:1,and the strength gradually decreased but elongation(EL)increased.With the extrusion speed increased from 3 to 6 mm/s,the grain sizes and DRX degree increased significantly,and the samples presented the typical<2111>-<1123>rare-earth(RE)textures.The alloy extruded at 260℃ with extrusion ratio of 10:1 and extrusion speed of 3 mm/s showed the tensile yield strength(TYS)of 213 MPa and EL of 30.6%.After quantitatively analyzing the contribution of strengthening mechanisms,it was found that the grain boundary strengthening and dislocation strengthening played major roles among strengthening contributions.These results provide some guidelines for enlarging the industrial application of extruded Mg-RE alloy.展开更多
Sodium-ion batteries have emerged as competitive substitutes for low-temperature applications due to severe capacity loss and safety concerns of lithium-ion batteries at−20°C or lower.However,the key capability o...Sodium-ion batteries have emerged as competitive substitutes for low-temperature applications due to severe capacity loss and safety concerns of lithium-ion batteries at−20°C or lower.However,the key capability of ultrafast charging at ultralow temperature for SIBs is rarely reported.Herein,a hybrid of Bi nanoparticles embedded in carbon nanorods is demonstrated as an ideal material to address this issue,which is synthesized via a high temperature shock method.Such a hybrid shows an unprecedented rate performance(237.9 mAh g^(−1) at 2 A g^(−1))at−60℃,outperforming all reported SIB anode materials.Coupled with a Na_(3)V_(2)(PO_(4))_(3)cathode,the energy density of the full cell can reach to 181.9 Wh kg^(−1) at−40°C.Based on this work,a novel strategy of high-rate activation is proposed to enhance performances of Bi-based materials in cryogenic conditions by creating new active sites for interfacial reaction under large current.展开更多
Using the software ANSYS-19.2/Explicit Dynamics,this study performedfinite-element modeling of the large-diameter steel pipeline cross-section for the Beineu-Bozoy-Shymkent gas pipeline with a non-through straight crac...Using the software ANSYS-19.2/Explicit Dynamics,this study performedfinite-element modeling of the large-diameter steel pipeline cross-section for the Beineu-Bozoy-Shymkent gas pipeline with a non-through straight crack,strengthened by steel wire wrapping.The effects of the thread tensile force of the steel winding in the form of single rings at the crack edges and the wires with different winding diameters and pitches were also studied.The results showed that the strengthening was preferably executed at a minimum value of the thread tensile force,which was 6.4%more effective than that at its maximum value.The analysis of the influence of the winding dia-meters showed that the equivalent stresses increased by 32%from the beginning of the crack growth until the wire broke.The increment in winding diameter decelerated the disclosure of the edge crack and reduced its length by 8.2%.The analysis of the influence of the winding pitch showed that decreasing the distance between the winding turns also led to a 33.6%reduction in the length of the straight crack and a 7.9%reduction in the maximum stres-ses on the strengthened pipeline cross-section.The analysis of the temperature effect on the pipeline material,within a range from-40℃ to+50℃,resulted in a crack length change of up to 5.8%.As the temperature dropped,the crack length decreased.Within such a temperature range,the maximum stresses were observed along the cen-tral area of the crack,which were equal to 413 MPa at+50℃ and 440 MPa at-40℃.The results also showed that the presence of the steel winding in the pipeline significantly reduced the length of crack propagation up to 8.4 times,depending on the temperature effect and design parameters of prestressing.This work integrated the existing methods for crack localization along steel gas pipelines.展开更多
This study examines the influence of magnetic field and temperature on the transient voltage of a polycrystalline silicon radial junction solar cell in a dynamic regime under multispectral illumination. Radial junctio...This study examines the influence of magnetic field and temperature on the transient voltage of a polycrystalline silicon radial junction solar cell in a dynamic regime under multispectral illumination. Radial junction solar cells represent a major advancement in photovoltaic technologies, as they optimize light absorption and charge collection efficiency. The focus is on the impact of the magnetic field and temperature on the decay of transient voltage, which provides crucial information on recombination processes and the lifetime of minority carriers. The results reveal that the magnetic field tends to increase the transient voltage by directly affecting the transient electron density. Indeed, for B > 7 × 10−5 T, the magnetic field prolongs the relaxation time by increasing the transient voltage amplitude. Additionally, rising temperatures accelerate (ranging from 290 K to 450 K) recombination processes, thereby reducing the transient voltage, although this effect is moderated by the presence of a magnetic field. The study highlights the complex interaction between magnetic field and temperature, with significant impacts on the transient behaviour.展开更多
The use of lithium-sulfur(Li-S)batteries is limited by sulfur redox reactions involving multi-phase transformations,especially at low-temperatures.To address this issue,we report a material(FCNS@NCFs)consisting of nit...The use of lithium-sulfur(Li-S)batteries is limited by sulfur redox reactions involving multi-phase transformations,especially at low-temperatures.To address this issue,we report a material(FCNS@NCFs)consisting of nitrogen-doped carbon fibers loaded with a ternary metal sulf-ide((Fe,Co,Ni)_(9)S_(8))for use as the sulfur host in Li-S batteries.This materi-al was prepared using transfer blot filter paper as the carbon precursor,thiourea as the source of nitrogen and sulfur,and FeCl_(3)·6H_(2)O,CoCl_(2)·6H_(2)O and NiCl_(2)·6H_(2)O as the metal ion sources.It was synthesized by an impreg-nation method followed by calcination.The nitrogen doping significantly in-creased the conductivity of the host,and the metal sulfides have excellent catalytic activities.Theoretical calculations,and adsorption and deposition experiments show that active sites on the surface of FCNS@NCFs selectively adsorb polysulfides,facilitate rapid adsorption and conversion,prevent cathode passivation and inhib-it the polysulfide shuttling.The FCNS@NCFs used as the sulfur host has excellent electrochemical properties.Its initial dis-charge capacity is 1639.0 mAh g^(−1) at 0.2 C and room temperature,and it remains a capacity of 1255.1 mAh g^(−1) after 100 cycles.At−20~C,it has an initial discharge capacity of 1578.5 mAh g^(−1) at 0.2 C,with a capacity of 867.5 mAh g^(−1) after 100 cycles.Its excellent performance at both ambient and low temperatures suggests a new way to produce high-performance low-temper-ature Li-S batteries.展开更多
The use of solar energy is today widely recognized for the green transition but also for addressing societal challenges associated with the rise in global surface temperature. The design of a photovoltaic solar panel ...The use of solar energy is today widely recognized for the green transition but also for addressing societal challenges associated with the rise in global surface temperature. The design of a photovoltaic solar panel field may require an understanding of how solar radiation oscillates with other variables or factors since multiple interactions occur during its transfer within the atmosphere. In this study, three years of the incoming shortwave radiation (SWin) and air temperature (Tair) data acquired within the “Institut de Mathématiques et de Sciences Physiques” were analyzed using the continuous wavelet transform to extract the inherent variability of these signals. The underlying characteristics meaning the timescale of these variabilities as well as the lead-lag relationship between SWin and Tair were also examined. With the wavelet power spectrum, the highest variability was evidenced at the 2 - 8 band period for the SWin, coinciding almost with that of Tair. This suggests that these two signals are well interconnected at this temporal scale. The results obtained with the phase (∅xy) difference analysis, reveal that SWin leads Tair by ~ 23.5˚ on average when (0 ∅xy∅xyi.e., periods ≤ 32 days), Tair increases with an increasing SWin since the lags between these two signals range between 0.09 - 2.30 days. However, when looking at their interdependence at a larger temporal scale (> 32 days), Tair lags SWin. An increase in SWin might not directly imply an increase in Tair. Overall, these findings give insight into complex relationships across scales between the incoming shortwave radiation and air temperature in a tropical humid region of Bénin.展开更多
The objective of this research is to investigate the effects of cosmic ray Forbush Decreases (FDs) exceeding 7% in magnitude, occurring between 1985 and 2016, on upper atmospheric pressure and temperature at Abha and ...The objective of this research is to investigate the effects of cosmic ray Forbush Decreases (FDs) exceeding 7% in magnitude, occurring between 1985 and 2016, on upper atmospheric pressure and temperature at Abha and Tabouk. Employing the super epoch analysis method, the study concentrated on altitudes of 5 km and 10 km, uncovering significant variations. Seasonal and synoptic-scale variations were considered and excluded when necessary across eight 9-day periods. Both locations showed considerable fluctuations in pressure and temperature before and after the events. At 5 km altitude (21 events), Abha experienced more pressure increases both before (9 vs. 7) and after (12 vs. 11) the events compared to Tabouk. For temperature, Abha recorded more increases before the events (5 vs. 1), while Tabouk showed more decreases (19 vs. 15). Post-event, Tabouk had more temperature increases (13 vs. 10). At 10 km altitude (20 events), both regions experienced more decreases than increases in pressure and temperature before the events and more increases afterward. Notably, Abha experienced more pressure increases both 4 days before (9 vs. 7) and after the events (12 vs. 11) than Tabouk. For temperature, Abha recorded more increases before the events (5 vs. 1), while Tabouk showed more decreases (19 vs. 15). Post-event, Tabouk had more temperature increases (13 vs. 10). These findings underscore both similarities and differences in atmospheric responses to FDs between Abha and Tabouk. Both locations exhibited cooling trends before and warming trends after the events, with Tabouk demonstrating a more pronounced warming trend post-event. These results enhance our understanding of the atmospheric dynamics linked to FDs and assist in predicting weather patterns associated with these phenomena.展开更多
Developing reliable adaptation and mitigation strategies to combat climate change is necessary at regional and local scales. The present study analyses the ability of the multi-model ensemble (MME) composed of fourtee...Developing reliable adaptation and mitigation strategies to combat climate change is necessary at regional and local scales. The present study analyses the ability of the multi-model ensemble (MME) composed of fourteen (14) CORDEX-Africa simulations to capture characteristics of the mean temperature for the present day (1979-2005) and associated extremes over Côte d’Ivoire. For this end, the analysis uses the mean variables of the temperature (i.e., minimum temperature (TMIN), mean temperature (TMEAN) and maximum temperature (TMAX)) as well as associated extremes such as intra-period extreme temperature range (ETR), warm spell duration index (HWFI) and warm days index (TX90P) during January-February-March (JFM), April-May-June (AMJ), July-August-September (JAS) and October-November-December (OND) seasons. The results indicate that mean temperature variables (TMIN, TMEAN and TMAX) are underestimated by CORDEX MME in general, except TMEAN in the centre of Côte d’Ivoire. On the other hand, extreme temperature indices are overestimated over Côte d’Ivoire, except ETR in JAS with an underestimation of about 2˚C and TX90P during JAS in the southern part of the country in JFM, AMJ and OND with an underestimation varying between 1% to 4%. In addition, CORDEX MME and observational datasets (CPC and NCEP) have a significant correlation in simulating temperature variables (TMIN, TMEAN, TMIN), while this correlation is not significant in general for extreme temperature, except ETR and HWFI. Furthermore, extreme temperatures (TX90P and HWFI) are characterized by more important interannual variability in the observations CPC and NCEP for ETR. Moreover, mean temperature variables (TMIN, TMEAN, TMAX) show slight interannual variability with respect to the observations CPC and NCEP, which are characterized by the most variability. Overall, CORDEX MME outperforms the seasonal and spatial variability of the temperature and associated extremes over Côte d’Ivoire, although some biases in representing their magnitudes. Thus, the results of the present study will help take appropriate adaptation and mitigation strategies against heatwaves and extreme temperature advent over Côte d’Ivoire as these climate extremes are projected to increase over the country.展开更多
The influence of pouring temperature and mold temperature on the fluidity and hot tearing behavior of Al-2Li-2Cu-0.5Mg-0.15Sc-0.1Zr-0.1Ti alloys was investigated by experimental investigation and simulation assessment...The influence of pouring temperature and mold temperature on the fluidity and hot tearing behavior of Al-2Li-2Cu-0.5Mg-0.15Sc-0.1Zr-0.1Ti alloys was investigated by experimental investigation and simulation assessment.The results showed that the length of the spiral fluidity sample increases from 302 to 756 mm as the pouring temperature increases from 680 to 740℃,and from 293 to 736 mm as the mold temperature increases from 200 to 400℃.The hot tearing susceptibility(HTS)firstly decreases and then increases with increasing pouring and mold temperatures,which is mainly caused by the oxide inclusion originating from the high activity of Li at excessive pouring temperature.Excessive pouring and mold temperatures easily produce oxide inclusions and holes,leading to a reduction in fluidity and an increase in HTS of the alloy.Combining the experimental and simulation results,the optimized pouring and mold temperatures are~720℃ and~300℃ for the cast Al-Li alloy,respectively.展开更多
This study investigates the compressive and tensile properties of basalt fiber-reinforced concrete (BFRC) after ultra-low-temperature freeze-thaw cycles. Scanning electron microscope (SEM) analysis was conducted to ex...This study investigates the compressive and tensile properties of basalt fiber-reinforced concrete (BFRC) after ultra-low-temperature freeze-thaw cycles. Scanning electron microscope (SEM) analysis was conducted to examine the deterioration mechanisms caused by freeze-thaw cycles and sulfate erosion. The results show that compressive and tensile strengths increase with basalt fiber dosage. The optimal dosage is 0.2%. With longer exposure to sulfate erosion, both strengths decline significantly. Basalt fibers effectively bridge cracks, control expansion, enhance compactness, and improve concrete performance. Ultra-low-temperature freeze-thaw cycles and sulfate erosion cause rapid crack growth. Sulfate erosion produces crystallization products and expansive substances. These fill cracks, create pressure, and damage the internal structure. Freezing and expansion forces further enlarge voids and cracks. This provides space for expansive substances, worsening concrete deterioration and reducing its performance.展开更多
Grafting is an effective technique for increasing the resistance of vegetables to biotic and abiotic stresses.It has been widely applied to produce solanaceous and melon vegetables.Temperature is an important external...Grafting is an effective technique for increasing the resistance of vegetables to biotic and abiotic stresses.It has been widely applied to produce solanaceous and melon vegetables.Temperature is an important external factor affecting graft formation.However,the molecular mechanism by which external ambient temperature affects tomato graft formation remains unclear.In this study,we demonstrated that elevating ambient temperature during grafting to 35℃ for more than 24 h after grafting accelerated vascular reconnection.We generated self-or heterografted combinations between phyB1B2 and pif4 loss-of-function mutant and wild-type plants,and were mutants unresponsive to graft formation at elevated ambient temperature.In addition,elevated ambient temperature induced SlPIF4 expression during grafting.SlPIF4 directly binds the promoters of auxin biosynthesis genes SlYUCCAs and activates their expression.Further investigation revealed auxin accumulation in the graft junction under elevated ambient temperature.The results illuminate the mechanism by which the PHYB-PIF4-auxin module promotes tomato graft formation in response to elevated ambient temperature.展开更多
Three-dimensional ocean subsurface temperature and salinity structures(OST/OSS)in the South China Sea(SCS)play crucial roles in oceanic climate research and disaster mitigation.Traditionally,real-time OST and OSS are ...Three-dimensional ocean subsurface temperature and salinity structures(OST/OSS)in the South China Sea(SCS)play crucial roles in oceanic climate research and disaster mitigation.Traditionally,real-time OST and OSS are mainly obtained through in-situ ocean observations and simulation by ocean circulation models,which are usually challenging and costly.Recently,dynamical,statistical,or machine learning models have been proposed to invert the OST/OSS from sea surface information;however,these models mainly focused on the inversion of monthly OST and OSS.To address this issue,we apply clustering algorithms and employ a stacking strategy to ensemble three models(XGBoost,Random Forest,and LightGBM)to invert the real-time OST/OSS based on satellite-derived data and the Argo dataset.Subsequently,a fusion of temperature and salinity is employed to reconstruct OST and OSS.In the validation dataset,the depth-averaged Correlation(Corr)of the estimated OST(OSS)is 0.919(0.83),and the average Root-Mean-Square Error(RMSE)is0.639°C(0.087 psu),with a depth-averaged coefficient of determination(R~2)of 0.84(0.68).Notably,at the thermocline where the base models exhibit their maximum error,the stacking-based fusion model exhibited significant performance enhancement,with a maximum enhancement in OST and OSS inversion exceeding 10%.We further found that the estimated OST and OSS exhibit good agreement with the HYbrid Coordinate Ocean Model(HYCOM)data and BOA_Argo dataset during the passage of a mesoscale eddy.This study shows that the proposed model can effectively invert the real-time OST and OSS,potentially enhancing the understanding of multi-scale oceanic processes in the SCS.展开更多
Tropical mountain peatlands in Brazil’s Southern Espinhaço Range are vital ecosystems,acting as carbon reservoirs,hydrological buffers,and biodiversity hotspots while sustaining traditional livelihoods and prese...Tropical mountain peatlands in Brazil’s Southern Espinhaço Range are vital ecosystems,acting as carbon reservoirs,hydrological buffers,and biodiversity hotspots while sustaining traditional livelihoods and preserving paleoenvironmental records.Despite their importance,peatlands outside protected areas face degradation by grazing and fires,threatening their ability to regulate ecosystem processes sensitive to temperature,such as greenhouse gas emissions,water cycling,biological activity,and organic matter decomposition.Since 2016,we have monitored peat temperatures in two contrasting peatlands–one preserved(within a protected area)and one disturbed(outside the protected area)–to understand how anthropogenic disturbances and climate variability impact these fragile ecosystems.Seasonal patterns dominated temperature variation,accounting for 60% of air and 81%–92% of peatland temperature variation.However,average temperatures and amplitudes differed between peatlands and depths.Interannual variability revealed stronger trends in the disturbed peatland,where a 1℃ increase in air temperature caused the trend to increase 0.70℃–0.87℃ on average at depths of 0.85 m–0.92 m.By contrast,the preserved peatland showed smaller increases(0.20℃–0.24℃)at comparable depths(1.06 m–1.24 m),suggesting a greater resilience.Temperature variation in the monitored peatlands was majorly driven by seasonal patterns,as revealed by time series decomposition and sinewave fit.Average temperature and amplitude varied between the two peatlands and among sampling sites,reflecting differences in environmental conditions and measurement depth.Interannual variability also exhibited distinct effects between peatlands and monitoring sites.The time series trend component showed more pronounced fluctuations at shallower depths and in the disturbed peatland.For every 1℃ increase in the trend component of the air temperature,the trend component of the peatland time series increased by 0.70℃ and 0.87℃on average at depths of 0.85 m and 0.92 m,respectively,in the disturbed peatland.In contrast,the preserved peatland exhibited smaller increases of 0.20℃ and 0.24℃ at comparable depths(1.06 m and 1.24 m).These findings highlight the potential for feedback responses between peatland disturbance and climate change,threatening their critical role in regulating carbon and water cycles.Expanding long-term monitoring,strengthening conservation efforts,and raising public awareness are essential to safeguard the ecosystem services provided by tropical mountain peatlands.展开更多
Implantable temperature sensors are revolutionizing physiological monitoring and playing a crucial role in diagnostics,therapeutics,and life sciences research.This review classifies the materials used in these sensors...Implantable temperature sensors are revolutionizing physiological monitoring and playing a crucial role in diagnostics,therapeutics,and life sciences research.This review classifies the materials used in these sensors into three categories:metal-based,inorganic semiconductor,and organic semiconductor materials.Metal-based materials are widely used in medical and industrial applications due to their linearity,stability,and reliability.Inorganic semiconductors provide rapid response times and high miniaturization potential,making them promising for biomedical and environmental monitoring.Organic semiconductors offer high sensitivity and ease of processing,enabling the development of flexible and stretchable sensors.This review analyzes recent studies for each material type,covering design principles,performance characteristics,and applications,highlighting key advantages and challenges regarding miniaturization,sensitivity,response time,and biocompatibility.Furthermore,critical performance parameters of implantable temperature sensors based on different material types are summarized,providing valuable references for future sensor design and optimization.The future development of implantable temperature sensors is discussed,focusing on improving biocompatibility,long-term stability,and multifunctional integration.These advancements are expected to expand the application potential of implantable sensors in telemedicine and dynamic physiological monitoring.展开更多
Studying the causes of summer(June–July–August)precipitation anomalies in the middle and lower reaches of the Yangtze River(MLYR)and accurately predicting rainy season precipitation are important to society and the ...Studying the causes of summer(June–July–August)precipitation anomalies in the middle and lower reaches of the Yangtze River(MLYR)and accurately predicting rainy season precipitation are important to society and the economy.In recent years,the sea surface temperature(SST)trend factor has been used to construct regression models for summer precipitation.In this study,through correlation analysis,winter SST anomaly predictors and the winter Central Pacific SST trend predictor(CPT)are identified as closely related to the following MLYR summer precipitation(YRSP).CPT can influence YRSP by inducing anomalous circulations over the North Pacific,guiding warm and moist air northward,and inhibiting the development of the anomalous anticyclone over the Northwest Pacific.This has improved the predictive skill of the seasonal regression model for YRSP.After incorporating the CPT,the correlation coefficient of the YRSP regression model improved by 40%,increasing from 0.45 to 0.63,and the root mean squared error decreased by 22%,from 1.15 to 0.90.展开更多
The pressure and temperature increase resulting from the impact of different threats onto target materials is analyzed with a unified laboratory-scale setup.This allows deriving qualitative information on the occurrin...The pressure and temperature increase resulting from the impact of different threats onto target materials is analyzed with a unified laboratory-scale setup.This allows deriving qualitative information on the occurring phenomenology as well as quantitative statements about the relative effects sizes as a function of target material and threat.The considered target materials are steel,aluminum,and magnesium.As threats,kinetic energy penetrator,explosively formed projectile,and shaped charge jet are used.For the investigated combinations,the measured overpressures vary by a factor of up to 5 for a variation of the material,by a factor of up to 7 for a variation of the threat,and by a factor larger than 15for a simultaneous variation of both.The obtained results as well as the experimental approach are relevant for the basic understanding of impact effects and risks due to material reactivity.The paper combines two main aims.Firstly,to provide a summary of own prior work in a coherent journal article and,secondly,to review and discuss these earlier results with a new perspective.展开更多
Low temperature(LT)in spring has become one of the principal abiotic stresses that restrict the growth and development of wheat.Diverse analyses were performed to investigate the mechanism underlying the response of w...Low temperature(LT)in spring has become one of the principal abiotic stresses that restrict the growth and development of wheat.Diverse analyses were performed to investigate the mechanism underlying the response of wheat grain development to LT stress during booting.These included morphological observation,measurements of starch synthase activity,and determination of amylose and amylopectin content of wheat grain after exposure to treatment with LT during booting.Additionally,proteomic analysis was performed using tandem mass tags(TMT).Results showed that the plumpness of wheat grains decreased after LT stress.Moreover,the activities of sucrose synthase(SuS,EC 2.4.1.13)and ADP-glucose pyrophosphorylase(AGPase,EC 2.7.7.27)exhibited a significant reduction,leading to a significant reduction in the contents of amylose and amylopectin.A total of 509 differentially expressed proteins(DEPs)were identified by proteomics analysis.The Gene Ontology(GO)enrichment analysis showed that the protein difference multiple in the nutritional repository activity was the largest among the molecular functions,and the up-regulated seed storage protein(ssP)played an active role in the response of grains to LT stress and subsequent damage.The Kyoto Encyclopedia of Genes and Genomes(KEGG)enrichment analysis showed that LT stress reduced the expression of DEPs such as sucrose phosphate synthase(SPS),glucose-1-phosphate adenylyltransferase(glgC),andβ-fructofuranosidase(FFase)in sucrose and starch metabolic pathways,thus affecting the synthesis of grain starch.In addition,many heat shock proteins(HsPs)were found in the protein processing in endoplasmic reticulum pathways,which can resist some damage caused by LT stress.These findings provide a new theoretical foundation for elucidating the underlying mechanism governing wheat yield developmentafterexposuretoLTstress inspring.展开更多
Thermal management system is highly desirable to guarantee the performance and thermal safety of lithium-ion batteries,but it reduces the energy density of battery modules and even is unable to provide highly effectiv...Thermal management system is highly desirable to guarantee the performance and thermal safety of lithium-ion batteries,but it reduces the energy density of battery modules and even is unable to provide highly effective protection.Here,a thermal management function integrated material is presented based on high-temperature resistant aerogel and phase change material and is applied at both charge–discharge process and thermal runaway condition.In this sandwich structure Paraffin@SiC nanowire/Aerogel sheet (denoted as PA@SAS) system,SiC nanowires endow the middle aerogel sheet (SAS) a dual nano-network structure.The enhanced mechanical properties of SAS were studied by compressive tests and dynamic mechanical analysis.Besides,the thermal conductivity of SAS at 600°C is only 0.042 W/(m K).The surface phase change material layers facilitate temperature uniformity of batteries (surface temperature difference less than 1.82°C) through latent heat.Moreover,a large-format battery module with four 58 Ah LiNi0.5Co0.2Mn0.3O2LIBs was assembled.PA@SAS successfully prevents thermal runaway propagation,yielding a temperature gap of 602°C through the 2 mm-thick cross section.PA@SAS also exhibits excellent performance in other safety issues such as temperature rise rate,flame heat flux,etc.The lightweight property and effective insulation performance achieves significant safety enhancement with mass and volume energy density reduction of only 0.79%and 5.4%,respectively.The originality of the present research stems from the micro and macro structure design of the proposed thermal management material and the combination of intrinsic advantages of every component.This work provides a reliable design of achieving the integration of thermal management functions into an aerogel composite and improves the thermal safety of lithium-ion batteries.展开更多
BACKGROUND: Targeted temperature management(TTM) is a common therapeutic intervention, yet its cost-effectiveness remains uncertain. This study aimed to evaluate the real-world cost-effectiveness of TTM compared with ...BACKGROUND: Targeted temperature management(TTM) is a common therapeutic intervention, yet its cost-effectiveness remains uncertain. This study aimed to evaluate the real-world cost-effectiveness of TTM compared with that of conventional care in adult out-of-hospital cardiac arrest(OHCA) survivors using clinical patient-level data.METHODS: We conducted a retrospective cohort study at an academic medical center in the USA to assess the cost-effectiveness of TTM in adult non-traumatic OHCA survivors between 1 January, 2019 and 30 June, 2023. The primary outcome was survival to hospital discharge. Incremental cost-effectiveness ratios(ICERs) were calculated and compared with various decision makers' willingness to pay. Cost-effectiveness acceptability curves were utilized to evaluate the economic attractiveness of TTM. Uncertainty about the incremental cost and effect was explored with a 95% confidence ellipse.RESULTS: Among 925 non-traumatic OHCA survivors, only 30(3%) received TTM. After adjusting for potential confounders, the TTM group did not demonstrate a significantly lower cost(delta cost-$5,141, 95% confidence interval [95% CI]: $-35,347 to $25,065, P=0.79) and higher survival to hospital discharge(delta effect 6%, 95% CI:-11% to 23%, P=0.41). Additionally, a 95% confidence ellipse indicated uncertainty reflected by evidence that the true value of the ICER could be in any of the quadrants of the cost-effectiveness plane.CONCLUSION: Although TTM did not demonstrate a clear survival benefit in this study, its potential cost-effectiveness warrants further investigation with larger sample sizes. These findings highlight the need for additional research to optimize TTM use in OHCA care and inform resource allocation decisions.展开更多
Microstructures and properties of mortar using ammonium phosphate and potassium phosphate were tested and compared in this case.Moreover,two cementitious additions and two lightweight aggregates,including fly ash,redi...Microstructures and properties of mortar using ammonium phosphate and potassium phosphate were tested and compared in this case.Moreover,two cementitious additions and two lightweight aggregates,including fly ash,redispersible latex powder,ceramsite sand,and rubber powder,were respectively tried to be applied in magnesium ammonium phosphate cement mortar in order to modify the microstructures and properties.The experimental results show that potassium phosphate is not suitable for magnesium phosphate cement mortar for cold region construction purpose.Although fly ash can bring positive modification in the condition of normal temperature curing,it brings negative effects in the condition of sub-zero temperature curing.Either redispersible latex powder or ceramsite sand can improve the freeze-thaw cycling resistance of magnesium phosphate cement mortar in the conditions of low temperature coupled with freeze-thaw cycling,but only the ceramsite sand can improve both mechanical properties and freeze-thaw cycling resistance.The modification caused by ceramsite sand is mainly due to the exceptional bonding strength between hardened cement paste and the porous surface of ceramsite and the porous structure of ceramsite for the release of frost heave stress.展开更多
基金supported by the National Science and Technology Major Project,China(No.2019-VI-0004-0118)the National Natural Science Foundation of China(No.51771152)the National Key R&D Program of China(No.2018YFB1106800)。
文摘Microstructure,texture,and mechanical properties of the extruded Mg-2.49Nd-1.82Gd-0.2Zn-0.2Zr alloy were investigated at different extrusion temperatures(260 and 320℃),extrusion ratios(10:1,15:1,and 30:1),and extrusion speeds(3 and 6 mm/s).The experimental results exhibited that the grain sizes after extrusion were much finer than that of the homogenized alloy,and the second phase showed streamline distribution along the extrusion direction(ED).With extrusion temperature increased from 260 to 320℃,the microstructure,texture,and mechanical properties of alloys changed slightly.The dynamic recrystallization(DRX)degree and grain sizes enhanced as the extrusion ratio increased from 10:1 to 30:1,and the strength gradually decreased but elongation(EL)increased.With the extrusion speed increased from 3 to 6 mm/s,the grain sizes and DRX degree increased significantly,and the samples presented the typical<2111>-<1123>rare-earth(RE)textures.The alloy extruded at 260℃ with extrusion ratio of 10:1 and extrusion speed of 3 mm/s showed the tensile yield strength(TYS)of 213 MPa and EL of 30.6%.After quantitatively analyzing the contribution of strengthening mechanisms,it was found that the grain boundary strengthening and dislocation strengthening played major roles among strengthening contributions.These results provide some guidelines for enlarging the industrial application of extruded Mg-RE alloy.
基金supported from Science and Technology Development Program of Jilin Province(Nos.20240101128JC,20230402058GH)National Natural Science Foundation of China(No.52130101).
文摘Sodium-ion batteries have emerged as competitive substitutes for low-temperature applications due to severe capacity loss and safety concerns of lithium-ion batteries at−20°C or lower.However,the key capability of ultrafast charging at ultralow temperature for SIBs is rarely reported.Herein,a hybrid of Bi nanoparticles embedded in carbon nanorods is demonstrated as an ideal material to address this issue,which is synthesized via a high temperature shock method.Such a hybrid shows an unprecedented rate performance(237.9 mAh g^(−1) at 2 A g^(−1))at−60℃,outperforming all reported SIB anode materials.Coupled with a Na_(3)V_(2)(PO_(4))_(3)cathode,the energy density of the full cell can reach to 181.9 Wh kg^(−1) at−40°C.Based on this work,a novel strategy of high-rate activation is proposed to enhance performances of Bi-based materials in cryogenic conditions by creating new active sites for interfacial reaction under large current.
基金funded by the Science Committee of the Ministry of Science and Higher Education of the Republic of Kazakhstan(Grant No.AP19680589).
文摘Using the software ANSYS-19.2/Explicit Dynamics,this study performedfinite-element modeling of the large-diameter steel pipeline cross-section for the Beineu-Bozoy-Shymkent gas pipeline with a non-through straight crack,strengthened by steel wire wrapping.The effects of the thread tensile force of the steel winding in the form of single rings at the crack edges and the wires with different winding diameters and pitches were also studied.The results showed that the strengthening was preferably executed at a minimum value of the thread tensile force,which was 6.4%more effective than that at its maximum value.The analysis of the influence of the winding dia-meters showed that the equivalent stresses increased by 32%from the beginning of the crack growth until the wire broke.The increment in winding diameter decelerated the disclosure of the edge crack and reduced its length by 8.2%.The analysis of the influence of the winding pitch showed that decreasing the distance between the winding turns also led to a 33.6%reduction in the length of the straight crack and a 7.9%reduction in the maximum stres-ses on the strengthened pipeline cross-section.The analysis of the temperature effect on the pipeline material,within a range from-40℃ to+50℃,resulted in a crack length change of up to 5.8%.As the temperature dropped,the crack length decreased.Within such a temperature range,the maximum stresses were observed along the cen-tral area of the crack,which were equal to 413 MPa at+50℃ and 440 MPa at-40℃.The results also showed that the presence of the steel winding in the pipeline significantly reduced the length of crack propagation up to 8.4 times,depending on the temperature effect and design parameters of prestressing.This work integrated the existing methods for crack localization along steel gas pipelines.
文摘This study examines the influence of magnetic field and temperature on the transient voltage of a polycrystalline silicon radial junction solar cell in a dynamic regime under multispectral illumination. Radial junction solar cells represent a major advancement in photovoltaic technologies, as they optimize light absorption and charge collection efficiency. The focus is on the impact of the magnetic field and temperature on the decay of transient voltage, which provides crucial information on recombination processes and the lifetime of minority carriers. The results reveal that the magnetic field tends to increase the transient voltage by directly affecting the transient electron density. Indeed, for B > 7 × 10−5 T, the magnetic field prolongs the relaxation time by increasing the transient voltage amplitude. Additionally, rising temperatures accelerate (ranging from 290 K to 450 K) recombination processes, thereby reducing the transient voltage, although this effect is moderated by the presence of a magnetic field. The study highlights the complex interaction between magnetic field and temperature, with significant impacts on the transient behaviour.
基金partially supported by National Natural Science Foundation of China(52172250)Institute of Process Engineering(IPE)Project for Frontier Basic Research(QYJC-2023-06)。
文摘The use of lithium-sulfur(Li-S)batteries is limited by sulfur redox reactions involving multi-phase transformations,especially at low-temperatures.To address this issue,we report a material(FCNS@NCFs)consisting of nitrogen-doped carbon fibers loaded with a ternary metal sulf-ide((Fe,Co,Ni)_(9)S_(8))for use as the sulfur host in Li-S batteries.This materi-al was prepared using transfer blot filter paper as the carbon precursor,thiourea as the source of nitrogen and sulfur,and FeCl_(3)·6H_(2)O,CoCl_(2)·6H_(2)O and NiCl_(2)·6H_(2)O as the metal ion sources.It was synthesized by an impreg-nation method followed by calcination.The nitrogen doping significantly in-creased the conductivity of the host,and the metal sulfides have excellent catalytic activities.Theoretical calculations,and adsorption and deposition experiments show that active sites on the surface of FCNS@NCFs selectively adsorb polysulfides,facilitate rapid adsorption and conversion,prevent cathode passivation and inhib-it the polysulfide shuttling.The FCNS@NCFs used as the sulfur host has excellent electrochemical properties.Its initial dis-charge capacity is 1639.0 mAh g^(−1) at 0.2 C and room temperature,and it remains a capacity of 1255.1 mAh g^(−1) after 100 cycles.At−20~C,it has an initial discharge capacity of 1578.5 mAh g^(−1) at 0.2 C,with a capacity of 867.5 mAh g^(−1) after 100 cycles.Its excellent performance at both ambient and low temperatures suggests a new way to produce high-performance low-temper-ature Li-S batteries.
文摘The use of solar energy is today widely recognized for the green transition but also for addressing societal challenges associated with the rise in global surface temperature. The design of a photovoltaic solar panel field may require an understanding of how solar radiation oscillates with other variables or factors since multiple interactions occur during its transfer within the atmosphere. In this study, three years of the incoming shortwave radiation (SWin) and air temperature (Tair) data acquired within the “Institut de Mathématiques et de Sciences Physiques” were analyzed using the continuous wavelet transform to extract the inherent variability of these signals. The underlying characteristics meaning the timescale of these variabilities as well as the lead-lag relationship between SWin and Tair were also examined. With the wavelet power spectrum, the highest variability was evidenced at the 2 - 8 band period for the SWin, coinciding almost with that of Tair. This suggests that these two signals are well interconnected at this temporal scale. The results obtained with the phase (∅xy) difference analysis, reveal that SWin leads Tair by ~ 23.5˚ on average when (0 ∅xy∅xyi.e., periods ≤ 32 days), Tair increases with an increasing SWin since the lags between these two signals range between 0.09 - 2.30 days. However, when looking at their interdependence at a larger temporal scale (> 32 days), Tair lags SWin. An increase in SWin might not directly imply an increase in Tair. Overall, these findings give insight into complex relationships across scales between the incoming shortwave radiation and air temperature in a tropical humid region of Bénin.
文摘The objective of this research is to investigate the effects of cosmic ray Forbush Decreases (FDs) exceeding 7% in magnitude, occurring between 1985 and 2016, on upper atmospheric pressure and temperature at Abha and Tabouk. Employing the super epoch analysis method, the study concentrated on altitudes of 5 km and 10 km, uncovering significant variations. Seasonal and synoptic-scale variations were considered and excluded when necessary across eight 9-day periods. Both locations showed considerable fluctuations in pressure and temperature before and after the events. At 5 km altitude (21 events), Abha experienced more pressure increases both before (9 vs. 7) and after (12 vs. 11) the events compared to Tabouk. For temperature, Abha recorded more increases before the events (5 vs. 1), while Tabouk showed more decreases (19 vs. 15). Post-event, Tabouk had more temperature increases (13 vs. 10). At 10 km altitude (20 events), both regions experienced more decreases than increases in pressure and temperature before the events and more increases afterward. Notably, Abha experienced more pressure increases both 4 days before (9 vs. 7) and after the events (12 vs. 11) than Tabouk. For temperature, Abha recorded more increases before the events (5 vs. 1), while Tabouk showed more decreases (19 vs. 15). Post-event, Tabouk had more temperature increases (13 vs. 10). These findings underscore both similarities and differences in atmospheric responses to FDs between Abha and Tabouk. Both locations exhibited cooling trends before and warming trends after the events, with Tabouk demonstrating a more pronounced warming trend post-event. These results enhance our understanding of the atmospheric dynamics linked to FDs and assist in predicting weather patterns associated with these phenomena.
文摘Developing reliable adaptation and mitigation strategies to combat climate change is necessary at regional and local scales. The present study analyses the ability of the multi-model ensemble (MME) composed of fourteen (14) CORDEX-Africa simulations to capture characteristics of the mean temperature for the present day (1979-2005) and associated extremes over Côte d’Ivoire. For this end, the analysis uses the mean variables of the temperature (i.e., minimum temperature (TMIN), mean temperature (TMEAN) and maximum temperature (TMAX)) as well as associated extremes such as intra-period extreme temperature range (ETR), warm spell duration index (HWFI) and warm days index (TX90P) during January-February-March (JFM), April-May-June (AMJ), July-August-September (JAS) and October-November-December (OND) seasons. The results indicate that mean temperature variables (TMIN, TMEAN and TMAX) are underestimated by CORDEX MME in general, except TMEAN in the centre of Côte d’Ivoire. On the other hand, extreme temperature indices are overestimated over Côte d’Ivoire, except ETR in JAS with an underestimation of about 2˚C and TX90P during JAS in the southern part of the country in JFM, AMJ and OND with an underestimation varying between 1% to 4%. In addition, CORDEX MME and observational datasets (CPC and NCEP) have a significant correlation in simulating temperature variables (TMIN, TMEAN, TMIN), while this correlation is not significant in general for extreme temperature, except ETR and HWFI. Furthermore, extreme temperatures (TX90P and HWFI) are characterized by more important interannual variability in the observations CPC and NCEP for ETR. Moreover, mean temperature variables (TMIN, TMEAN, TMAX) show slight interannual variability with respect to the observations CPC and NCEP, which are characterized by the most variability. Overall, CORDEX MME outperforms the seasonal and spatial variability of the temperature and associated extremes over Côte d’Ivoire, although some biases in representing their magnitudes. Thus, the results of the present study will help take appropriate adaptation and mitigation strategies against heatwaves and extreme temperature advent over Côte d’Ivoire as these climate extremes are projected to increase over the country.
基金financially supported by the National Natural Science Foundation of China(Nos.51871148,51821001)。
文摘The influence of pouring temperature and mold temperature on the fluidity and hot tearing behavior of Al-2Li-2Cu-0.5Mg-0.15Sc-0.1Zr-0.1Ti alloys was investigated by experimental investigation and simulation assessment.The results showed that the length of the spiral fluidity sample increases from 302 to 756 mm as the pouring temperature increases from 680 to 740℃,and from 293 to 736 mm as the mold temperature increases from 200 to 400℃.The hot tearing susceptibility(HTS)firstly decreases and then increases with increasing pouring and mold temperatures,which is mainly caused by the oxide inclusion originating from the high activity of Li at excessive pouring temperature.Excessive pouring and mold temperatures easily produce oxide inclusions and holes,leading to a reduction in fluidity and an increase in HTS of the alloy.Combining the experimental and simulation results,the optimized pouring and mold temperatures are~720℃ and~300℃ for the cast Al-Li alloy,respectively.
文摘This study investigates the compressive and tensile properties of basalt fiber-reinforced concrete (BFRC) after ultra-low-temperature freeze-thaw cycles. Scanning electron microscope (SEM) analysis was conducted to examine the deterioration mechanisms caused by freeze-thaw cycles and sulfate erosion. The results show that compressive and tensile strengths increase with basalt fiber dosage. The optimal dosage is 0.2%. With longer exposure to sulfate erosion, both strengths decline significantly. Basalt fibers effectively bridge cracks, control expansion, enhance compactness, and improve concrete performance. Ultra-low-temperature freeze-thaw cycles and sulfate erosion cause rapid crack growth. Sulfate erosion produces crystallization products and expansive substances. These fill cracks, create pressure, and damage the internal structure. Freezing and expansion forces further enlarge voids and cracks. This provides space for expansive substances, worsening concrete deterioration and reducing its performance.
基金supported by China Agriculture Research System of MOF and MARA(Grant No.CARS23-B10)The Major Science and Technology Projects in Hainan Province(Grant No.ZDKJ2021005)+1 种基金Key R&D projects in Shandong Province(Grant No.LJNY202106)Central Public-interest Scientific Institution Basal Research Fund(Grant No.IVF-BRF2023006)。
文摘Grafting is an effective technique for increasing the resistance of vegetables to biotic and abiotic stresses.It has been widely applied to produce solanaceous and melon vegetables.Temperature is an important external factor affecting graft formation.However,the molecular mechanism by which external ambient temperature affects tomato graft formation remains unclear.In this study,we demonstrated that elevating ambient temperature during grafting to 35℃ for more than 24 h after grafting accelerated vascular reconnection.We generated self-or heterografted combinations between phyB1B2 and pif4 loss-of-function mutant and wild-type plants,and were mutants unresponsive to graft formation at elevated ambient temperature.In addition,elevated ambient temperature induced SlPIF4 expression during grafting.SlPIF4 directly binds the promoters of auxin biosynthesis genes SlYUCCAs and activates their expression.Further investigation revealed auxin accumulation in the graft junction under elevated ambient temperature.The results illuminate the mechanism by which the PHYB-PIF4-auxin module promotes tomato graft formation in response to elevated ambient temperature.
基金jointly supported by the National Key Research and Development Program of China(2022YFC3104304)the National Natural Science Foundation of China(Grant No.41876011)+1 种基金the 2022 Research Program of Sanya Yazhou Bay Science and Technology City(SKJC-2022-01-001)the Hainan Province Science and Technology Special Fund(ZDYF2021SHFZ265)。
文摘Three-dimensional ocean subsurface temperature and salinity structures(OST/OSS)in the South China Sea(SCS)play crucial roles in oceanic climate research and disaster mitigation.Traditionally,real-time OST and OSS are mainly obtained through in-situ ocean observations and simulation by ocean circulation models,which are usually challenging and costly.Recently,dynamical,statistical,or machine learning models have been proposed to invert the OST/OSS from sea surface information;however,these models mainly focused on the inversion of monthly OST and OSS.To address this issue,we apply clustering algorithms and employ a stacking strategy to ensemble three models(XGBoost,Random Forest,and LightGBM)to invert the real-time OST/OSS based on satellite-derived data and the Argo dataset.Subsequently,a fusion of temperature and salinity is employed to reconstruct OST and OSS.In the validation dataset,the depth-averaged Correlation(Corr)of the estimated OST(OSS)is 0.919(0.83),and the average Root-Mean-Square Error(RMSE)is0.639°C(0.087 psu),with a depth-averaged coefficient of determination(R~2)of 0.84(0.68).Notably,at the thermocline where the base models exhibit their maximum error,the stacking-based fusion model exhibited significant performance enhancement,with a maximum enhancement in OST and OSS inversion exceeding 10%.We further found that the estimated OST and OSS exhibit good agreement with the HYbrid Coordinate Ocean Model(HYCOM)data and BOA_Argo dataset during the passage of a mesoscale eddy.This study shows that the proposed model can effectively invert the real-time OST and OSS,potentially enhancing the understanding of multi-scale oceanic processes in the SCS.
基金This study was financed in part by the Coordenacao de Aperfeiçoamento de Pessoal de Nivel Superior-Brasil(CAPES)-Finance Code 001the Brazilian Conselho Nacional de Pesquisa-CNPq(study and research grants and research funding-Process 303666/2018-8,408162/2018-0,441335/2020-9,302969/2021-7,and 50484/2022-4)Fundacao de ApoioaPesquisa do Estado de Minas Gerais-FAPEMIG(study grants and research funding-Process CRA/APQ 0100-18,APQ-03364-21 and CAG/PPM 00568-16).
文摘Tropical mountain peatlands in Brazil’s Southern Espinhaço Range are vital ecosystems,acting as carbon reservoirs,hydrological buffers,and biodiversity hotspots while sustaining traditional livelihoods and preserving paleoenvironmental records.Despite their importance,peatlands outside protected areas face degradation by grazing and fires,threatening their ability to regulate ecosystem processes sensitive to temperature,such as greenhouse gas emissions,water cycling,biological activity,and organic matter decomposition.Since 2016,we have monitored peat temperatures in two contrasting peatlands–one preserved(within a protected area)and one disturbed(outside the protected area)–to understand how anthropogenic disturbances and climate variability impact these fragile ecosystems.Seasonal patterns dominated temperature variation,accounting for 60% of air and 81%–92% of peatland temperature variation.However,average temperatures and amplitudes differed between peatlands and depths.Interannual variability revealed stronger trends in the disturbed peatland,where a 1℃ increase in air temperature caused the trend to increase 0.70℃–0.87℃ on average at depths of 0.85 m–0.92 m.By contrast,the preserved peatland showed smaller increases(0.20℃–0.24℃)at comparable depths(1.06 m–1.24 m),suggesting a greater resilience.Temperature variation in the monitored peatlands was majorly driven by seasonal patterns,as revealed by time series decomposition and sinewave fit.Average temperature and amplitude varied between the two peatlands and among sampling sites,reflecting differences in environmental conditions and measurement depth.Interannual variability also exhibited distinct effects between peatlands and monitoring sites.The time series trend component showed more pronounced fluctuations at shallower depths and in the disturbed peatland.For every 1℃ increase in the trend component of the air temperature,the trend component of the peatland time series increased by 0.70℃ and 0.87℃on average at depths of 0.85 m and 0.92 m,respectively,in the disturbed peatland.In contrast,the preserved peatland exhibited smaller increases of 0.20℃ and 0.24℃ at comparable depths(1.06 m and 1.24 m).These findings highlight the potential for feedback responses between peatland disturbance and climate change,threatening their critical role in regulating carbon and water cycles.Expanding long-term monitoring,strengthening conservation efforts,and raising public awareness are essential to safeguard the ecosystem services provided by tropical mountain peatlands.
基金supported by the National Natural Science Foundation of China(NSFC)(62422501)Beijing Nova Program(20230484254,20240484742)Hebei Natural Science Foundation(F2024105039).
文摘Implantable temperature sensors are revolutionizing physiological monitoring and playing a crucial role in diagnostics,therapeutics,and life sciences research.This review classifies the materials used in these sensors into three categories:metal-based,inorganic semiconductor,and organic semiconductor materials.Metal-based materials are widely used in medical and industrial applications due to their linearity,stability,and reliability.Inorganic semiconductors provide rapid response times and high miniaturization potential,making them promising for biomedical and environmental monitoring.Organic semiconductors offer high sensitivity and ease of processing,enabling the development of flexible and stretchable sensors.This review analyzes recent studies for each material type,covering design principles,performance characteristics,and applications,highlighting key advantages and challenges regarding miniaturization,sensitivity,response time,and biocompatibility.Furthermore,critical performance parameters of implantable temperature sensors based on different material types are summarized,providing valuable references for future sensor design and optimization.The future development of implantable temperature sensors is discussed,focusing on improving biocompatibility,long-term stability,and multifunctional integration.These advancements are expected to expand the application potential of implantable sensors in telemedicine and dynamic physiological monitoring.
基金Guangdong Major Project of Basic and Applied Basic Research(2020B0301030004)National Natural Science Foundation of China(42175061)。
文摘Studying the causes of summer(June–July–August)precipitation anomalies in the middle and lower reaches of the Yangtze River(MLYR)and accurately predicting rainy season precipitation are important to society and the economy.In recent years,the sea surface temperature(SST)trend factor has been used to construct regression models for summer precipitation.In this study,through correlation analysis,winter SST anomaly predictors and the winter Central Pacific SST trend predictor(CPT)are identified as closely related to the following MLYR summer precipitation(YRSP).CPT can influence YRSP by inducing anomalous circulations over the North Pacific,guiding warm and moist air northward,and inhibiting the development of the anomalous anticyclone over the Northwest Pacific.This has improved the predictive skill of the seasonal regression model for YRSP.After incorporating the CPT,the correlation coefficient of the YRSP regression model improved by 40%,increasing from 0.45 to 0.63,and the root mean squared error decreased by 22%,from 1.15 to 0.90.
文摘The pressure and temperature increase resulting from the impact of different threats onto target materials is analyzed with a unified laboratory-scale setup.This allows deriving qualitative information on the occurring phenomenology as well as quantitative statements about the relative effects sizes as a function of target material and threat.The considered target materials are steel,aluminum,and magnesium.As threats,kinetic energy penetrator,explosively formed projectile,and shaped charge jet are used.For the investigated combinations,the measured overpressures vary by a factor of up to 5 for a variation of the material,by a factor of up to 7 for a variation of the threat,and by a factor larger than 15for a simultaneous variation of both.The obtained results as well as the experimental approach are relevant for the basic understanding of impact effects and risks due to material reactivity.The paper combines two main aims.Firstly,to provide a summary of own prior work in a coherent journal article and,secondly,to review and discuss these earlier results with a new perspective.
基金supported by the National Natural Science Foundation of China(32372223)the National Key Research and Development Program of China(2022YFD2301404)+1 种基金the College Students'Innovationand Entrepreneurship Training Program of Anhui Province,China(S202210364136)the Natural Science Research Project of Anhui Educational Committee,China(2023AH040133).
文摘Low temperature(LT)in spring has become one of the principal abiotic stresses that restrict the growth and development of wheat.Diverse analyses were performed to investigate the mechanism underlying the response of wheat grain development to LT stress during booting.These included morphological observation,measurements of starch synthase activity,and determination of amylose and amylopectin content of wheat grain after exposure to treatment with LT during booting.Additionally,proteomic analysis was performed using tandem mass tags(TMT).Results showed that the plumpness of wheat grains decreased after LT stress.Moreover,the activities of sucrose synthase(SuS,EC 2.4.1.13)and ADP-glucose pyrophosphorylase(AGPase,EC 2.7.7.27)exhibited a significant reduction,leading to a significant reduction in the contents of amylose and amylopectin.A total of 509 differentially expressed proteins(DEPs)were identified by proteomics analysis.The Gene Ontology(GO)enrichment analysis showed that the protein difference multiple in the nutritional repository activity was the largest among the molecular functions,and the up-regulated seed storage protein(ssP)played an active role in the response of grains to LT stress and subsequent damage.The Kyoto Encyclopedia of Genes and Genomes(KEGG)enrichment analysis showed that LT stress reduced the expression of DEPs such as sucrose phosphate synthase(SPS),glucose-1-phosphate adenylyltransferase(glgC),andβ-fructofuranosidase(FFase)in sucrose and starch metabolic pathways,thus affecting the synthesis of grain starch.In addition,many heat shock proteins(HsPs)were found in the protein processing in endoplasmic reticulum pathways,which can resist some damage caused by LT stress.These findings provide a new theoretical foundation for elucidating the underlying mechanism governing wheat yield developmentafterexposuretoLTstress inspring.
基金Collaborative Innovation University Project of Anhui Province (GXXT-2022-018)National Natural Science Foundation of China (52374238 and 52074253)+3 种基金Natural Science Foundation of Anhui Province (2108085J28)Taishan Industrial Leading Talent Project (2019TSCYCX-27)Major Science and Technology Projects of Anhui Province(202103a05020011)Youth Innovation Promotion Association(CX2320007001)。
文摘Thermal management system is highly desirable to guarantee the performance and thermal safety of lithium-ion batteries,but it reduces the energy density of battery modules and even is unable to provide highly effective protection.Here,a thermal management function integrated material is presented based on high-temperature resistant aerogel and phase change material and is applied at both charge–discharge process and thermal runaway condition.In this sandwich structure Paraffin@SiC nanowire/Aerogel sheet (denoted as PA@SAS) system,SiC nanowires endow the middle aerogel sheet (SAS) a dual nano-network structure.The enhanced mechanical properties of SAS were studied by compressive tests and dynamic mechanical analysis.Besides,the thermal conductivity of SAS at 600°C is only 0.042 W/(m K).The surface phase change material layers facilitate temperature uniformity of batteries (surface temperature difference less than 1.82°C) through latent heat.Moreover,a large-format battery module with four 58 Ah LiNi0.5Co0.2Mn0.3O2LIBs was assembled.PA@SAS successfully prevents thermal runaway propagation,yielding a temperature gap of 602°C through the 2 mm-thick cross section.PA@SAS also exhibits excellent performance in other safety issues such as temperature rise rate,flame heat flux,etc.The lightweight property and effective insulation performance achieves significant safety enhancement with mass and volume energy density reduction of only 0.79%and 5.4%,respectively.The originality of the present research stems from the micro and macro structure design of the proposed thermal management material and the combination of intrinsic advantages of every component.This work provides a reliable design of achieving the integration of thermal management functions into an aerogel composite and improves the thermal safety of lithium-ion batteries.
基金supported by Faculty of MedicineChiang Mai University+2 种基金supported by the National Center for Advancing Translational SciencesNational Institutes of Healththrough grant number UL1 TR001860. The content is solely the responsibility of the authors and does not necessarily represent the official views of the NIH。
文摘BACKGROUND: Targeted temperature management(TTM) is a common therapeutic intervention, yet its cost-effectiveness remains uncertain. This study aimed to evaluate the real-world cost-effectiveness of TTM compared with that of conventional care in adult out-of-hospital cardiac arrest(OHCA) survivors using clinical patient-level data.METHODS: We conducted a retrospective cohort study at an academic medical center in the USA to assess the cost-effectiveness of TTM in adult non-traumatic OHCA survivors between 1 January, 2019 and 30 June, 2023. The primary outcome was survival to hospital discharge. Incremental cost-effectiveness ratios(ICERs) were calculated and compared with various decision makers' willingness to pay. Cost-effectiveness acceptability curves were utilized to evaluate the economic attractiveness of TTM. Uncertainty about the incremental cost and effect was explored with a 95% confidence ellipse.RESULTS: Among 925 non-traumatic OHCA survivors, only 30(3%) received TTM. After adjusting for potential confounders, the TTM group did not demonstrate a significantly lower cost(delta cost-$5,141, 95% confidence interval [95% CI]: $-35,347 to $25,065, P=0.79) and higher survival to hospital discharge(delta effect 6%, 95% CI:-11% to 23%, P=0.41). Additionally, a 95% confidence ellipse indicated uncertainty reflected by evidence that the true value of the ICER could be in any of the quadrants of the cost-effectiveness plane.CONCLUSION: Although TTM did not demonstrate a clear survival benefit in this study, its potential cost-effectiveness warrants further investigation with larger sample sizes. These findings highlight the need for additional research to optimize TTM use in OHCA care and inform resource allocation decisions.
基金Funded by the National Natural Science Foundation of China(No.51878227)。
文摘Microstructures and properties of mortar using ammonium phosphate and potassium phosphate were tested and compared in this case.Moreover,two cementitious additions and two lightweight aggregates,including fly ash,redispersible latex powder,ceramsite sand,and rubber powder,were respectively tried to be applied in magnesium ammonium phosphate cement mortar in order to modify the microstructures and properties.The experimental results show that potassium phosphate is not suitable for magnesium phosphate cement mortar for cold region construction purpose.Although fly ash can bring positive modification in the condition of normal temperature curing,it brings negative effects in the condition of sub-zero temperature curing.Either redispersible latex powder or ceramsite sand can improve the freeze-thaw cycling resistance of magnesium phosphate cement mortar in the conditions of low temperature coupled with freeze-thaw cycling,but only the ceramsite sand can improve both mechanical properties and freeze-thaw cycling resistance.The modification caused by ceramsite sand is mainly due to the exceptional bonding strength between hardened cement paste and the porous surface of ceramsite and the porous structure of ceramsite for the release of frost heave stress.
