The velocity ratio of a free shear layer has an important influence on the spatial development of the large scale coherent structures in the layer. In this study, numerical simulations are performed to get an insight ...The velocity ratio of a free shear layer has an important influence on the spatial development of the large scale coherent structures in the layer. In this study, numerical simulations are performed to get an insight into this problem. The obtained numerical results agree quite well with those of a linear inviscid stability theory and the available experimental data.展开更多
A new computational algorithm is introduced for solving scattering problem in periodic structure. The PML technique is used to deal with the difficulty on truncating the unbounded domain while the DSC algorithm is uti...A new computational algorithm is introduced for solving scattering problem in periodic structure. The PML technique is used to deal with the difficulty on truncating the unbounded domain while the DSC algorithm is utilized for the spatial discretization. The present study reveals that the method is efficient for solving the problem.展开更多
Considering the mechnoelectrical coupling, the localization of SH-waves in disordered periodic layered piezoelectric structures is studied. The waves propagating in directions normal and tangential to the layers are c...Considering the mechnoelectrical coupling, the localization of SH-waves in disordered periodic layered piezoelectric structures is studied. The waves propagating in directions normal and tangential to the layers are considered. The transfer matrices between two consecutive unit cells are obtained according to the continuity conditions. The expressions of localization factor and localization length in the disordered periodic structures are presented. For the disordered periodic piezoelectric structures, the numerical results of localization factor and localization length are presented and discussed. It can be seen from the results that the frequency passbands and stopbands appear for the ordered periodic structures and the wave localization phenomenon occurs in the disordered periodic ones, and the larger the coefficient of variation is, the greater the degree of wave localization is. The widths of stopbands in the ordered periodic structures are very narrow when the properties of the consecutive piezoelectric materials are similar and the intervals of stopbands become broader when a certain material parameter has large changes. For the wave propagating in the direction normal to the layers the localization length has less dependence on the frequency, but for the wave propagating in the direction tangential to the layers the localization length is strongly dependent on the frequency.展开更多
This paper investigates shear horizontal （SH） waves propagating in a periodically layered structure that consists of piezoelectric （PE） layers perfectly bonded with piezomagnetic （PM） layers alternately. The exp...This paper investigates shear horizontal （SH） waves propagating in a periodically layered structure that consists of piezoelectric （PE） layers perfectly bonded with piezomagnetic （PM） layers alternately. The explicit dispersion relations are derived for the two cases when the propagation directions of SH waves are normal to the interface and parallel to the interface, respectively. The asymptotic expressions for dispersion relations are also given when the wave number is extremely small. Numerical results for stop band effect and phase velocity are presented for a periodic system of alternating BaTiO3 and Terfenol-D layers. The influence of volume fraction on stop band effect and dispersion behaviors is discussed and revealed.展开更多
The Tazhong paleouplift is divided into the upper and the lower structural layers, bounded by the unconformity surface at the top of the Ordovician carbonate rock. The reservoirs in the two layers from different parts...The Tazhong paleouplift is divided into the upper and the lower structural layers, bounded by the unconformity surface at the top of the Ordovician carbonate rock. The reservoirs in the two layers from different parts vary in number, type and reserves, but the mechanism was rarely researched before. Therefore, an explanation of the mechanism will promote petroleum exploration in Tazhong paleouplift. After studying the evolution and reservoir distribution of the Tazhong paleouplift, it is concluded that the evolution in late Caledonian, late Hercynian and Himalayan periods resulted in the upper and the lower structural layers. It is also defined that in the upper structural layer, structural and stratigraphic overlap reservoirs are developed at the top and the upper part of the paleouplift, which are dominated by oil reservoirs, while for the lower structural layer, lithological reservoirs are developed in the lower part of the paleouplift, which are dominated by gas reservoirs, and more reserves are discovered in the lower structural layer than the upper. Through a comparative analysis of accumulation conditions of the upper and the lower structural layers, the mechanism of enrichment differences is clearly explained. The reservoir and seal conditions of the lower structural layer are better than those of the upper layer, which is the reason why more reservoirs have been found in the former. The differences in the carrier system types, trap types and charging periods between the upper and the lower structural layers lead to differences in the reservoir types and distribution. An accumulation model is established for the Tazhong paleouplift. For the upper structural layer, the structural reservoirs and the stratigraphic overlap reservoirs are formed at the upper part of the paleouplift, while for the lower structural layer, the weathering crust reservoirs are formed at the top, the reef-flat reservoirs are formed on the lateral margin, the karst and inside reservoirs are formed in the lower part of the paleouplift.展开更多
The propagation of surface acoustic waves in layered piezoelectric structureswith initial stresses is investigated. The phase velocity equations are obtained for electricallyfree and shorted cases, respectively. Effec...The propagation of surface acoustic waves in layered piezoelectric structureswith initial stresses is investigated. The phase velocity equations are obtained for electricallyfree and shorted cases, respectively. Effects of the initial stresses on the phase velocity and theelectromechanical coupling coefficient for the fundamental mode of the layered piezoelectricstructures are discussed. Numerical results for the c-axis oriented film of LiNbO_3 on a sapphiresubstrate are given. It is found that the fractional change in phase velocity is a linear functionwith the initial stresses, and the electromechanical coupling factor increases with an increase ofthe absolute values of the compressive initial stresses. The results are useful for the design ofsurface acoustic wave devices.展开更多
Luquire et al. ' s impedance change model of a rectangular cross section probe coil above a structure with an arbitrary number of parallel layers was used to study the principle of measuring thicknesses of multi-l...Luquire et al. ' s impedance change model of a rectangular cross section probe coil above a structure with an arbitrary number of parallel layers was used to study the principle of measuring thicknesses of multi-layered structures in terms of eddy current testing voltage measurements. An experimental system for multi-layered thickness measurement was developed and several fitting models to formulate the relationships between detected impedance/voltage measurements and thickness are put forward using least square method. The determination of multi-layered thicknesses was investigated after inversing the voltage outputs of the detecting system. The best fitting and inversion models are presented.展开更多
Nature has shown us that the microstructure of the skin of fast-swimming sharks in the ocean can reduce the skin friction drag due to the well-known shark-skin effect.In the present study,the effect of shark-skin-insp...Nature has shown us that the microstructure of the skin of fast-swimming sharks in the ocean can reduce the skin friction drag due to the well-known shark-skin effect.In the present study,the effect of shark-skin-inspired riblets on coherent vortex structures in a turbulent boundary layer（TBL） is investigated.This is done by means of tomographic particle image velocimetry（TPIV） measurements in channel fl ws over an acrylic plate of drag-reducing riblets at a friction Reynolds number of 190.The turbulent fl ws over drag-reducing riblets are verifie by a planar time-resolved particle image velocimetry（TRPIV） system initially,and then the TPIV measurements are performed.Two-dimensional（2D） experimental results with a dragreduction rate of around 4.81% are clearly visible over triangle riblets with a peak-to-peak spacing s＋of 14,indicating from the drag-reducing performance that the buffer layer within the TBL has thickened;the logarithmic law region has shifted upward and the Reynolds shear stress decreased.A comparison of the spatial topological distributions of the spanwise vorticity of coherent vortex structures extracted at different wall-normal heights through the improved quadrant splitting method shows that riblets weaken the amplitudesof the spanwise vorticity when ejection（Q2） and sweep（Q4） events occur at the near wall,having the greatest effect on Q4 events in particular.The so-called quadrupole statistical model for coherent structures in the whole TBL is verified Meanwhile,their spatial conditional-averaged topological shapes and the spatial scales of quadrupole coherent vortex structures as a whole in the overlying turbulent fl w over riblets are changed,suggesting that the riblets dampen the momentum and energy exchange between the regions of near-wall and outer portion of the TBL by depressing the bursting events（Q2 and Q4）,thereby reducing the skin friction drag.展开更多
Discontinuous Galerkin（DG） method is known to have several advantages for flow simulations,in particular,in fiexible accuracy management and adaptability to mesh refinement. In the present work,the DG method is deve...Discontinuous Galerkin（DG） method is known to have several advantages for flow simulations,in particular,in fiexible accuracy management and adaptability to mesh refinement. In the present work,the DG method is developed for numerical simulations of both temporally and spatially developing mixing layers. For the temporally developing mixing layer,both the instantaneous fiow field and time evolution of momentum thickness agree very well with the previous results. Shocklets are observed at higher convective Mach numbers and the vortex paring manner is changed for high compressibility. For the spatially developing mixing layer,large-scale coherent structures and self-similar behavior for mean profiles are investigated. The instantaneous fiow field for a three-dimensional compressible mixing layer is also reported,which shows the development of largescale coherent structures in the streamwise direction. All numerical results suggest that the DG method is effective in performing accurate numerical simulations for compressible shear fiows.展开更多
2D nanosheets such as graphene, silicene, phosphorene, metal dichalcogenides and MXenes are emerging and promising for lithium storage due to their ultrathin nature and corresponding chemical/physical properties. Howe...2D nanosheets such as graphene, silicene, phosphorene, metal dichalcogenides and MXenes are emerging and promising for lithium storage due to their ultrathin nature and corresponding chemical/physical properties. However, the serious restacking and aggregation of the 2D nanosheets are still hampering their applications. To circumvent the issues of 2D nanosheets, one efficient strategy is to construct 3D structures with hierarchical porous structures, good chemical/mechanical stabilities and tunable electrical conductivities. In this review, we firstly focus on the available synthetic approaches of 3D structures from 2D nanosheets, and then summarize the relationships between the microstructures of 3D structures built from 2D nanosheets and their electrochemical behaviors for lithium storage. On the basis of above results, some challenges are briefly discussed in the perspective of the development of various functional 3D structures.展开更多
In this paper, an experimental investigation on the flow structures in a turbulent bounda- ry layer employing a special laser light sheet-Hydrogen bubble flow visualization technique is described. It is observed that ...In this paper, an experimental investigation on the flow structures in a turbulent bounda- ry layer employing a special laser light sheet-Hydrogen bubble flow visualization technique is described. It is observed that the high/low speed streaks are directly related to the hairpin or horseshoe-like vortices. This observation can give a better understanding of the physical mechanism in the turbulent boundary layer.展开更多
The microstructural features of clacium rare earth(Ca RE) fluorocarbonate minerals from Southwest China were studied by using selected area electron diffraction(SAED) and high resolution transmission electron micros...The microstructural features of clacium rare earth(Ca RE) fluorocarbonate minerals from Southwest China were studied by using selected area electron diffraction(SAED) and high resolution transmission electron microscopy(HRTEM). Three new regularly mixed layer structures of B 8S 6 type with long period and different stacking sequence, i.e. B 8S 6 Ⅰ, B 8S 6 Ⅱ, and B 8S 6 Ⅲ, were found in the derived polycrystal of parisite, in which their structural symmetry, cell parameters, chemical formulas of crystal and stacking models of structural unit layer, etc. were determined. The results of this study also show that these new regularly mixed layer structrues were formed by order stacking unit layer of bastnaesite(B) and synchisite(S) in varying proportion along c axis. The observation under HRTEM reveals that in the three new regularly mixed layer structures there are different distribution modes of Ce F ion layers, CO 2- 3 ion groups between the Ce F ion layers, and CO 2- 3 ion groups between Ce F and Ca 2+ ion layers, and there are some heterogeneous textures, such as disorder interlayer and stacking fault. It further proves the complexity of the crystal structure of the Ca RE fluorocarbonate minerals.展开更多
The coupling agents content and thickness on glass fiber (GF) surfaces which have been treated with silanes and titanates under different conditions are tested by means of XRF (X-Ray Fluorescent spectrometry). And the...The coupling agents content and thickness on glass fiber (GF) surfaces which have been treated with silanes and titanates under different conditions are tested by means of XRF (X-Ray Fluorescent spectrometry). And the rheological characteristics of the dispersed systems prepared from the above glass fibers combined with unsaturated polyester resin (UP) are discussed. The results show that the rigidity of the internal layers of silane coupling agent absorbed by glass surfaces is greater than the one of the external layers; while the effect of the titanate coupling agents on the rheolo- gical characteristics of the system is approximately the same in each structural layer, that is due to the fact that both the internal and external layers of titanates on glass surfaces have the similar flexible structures.展开更多
The utilization of eco-friendly,lightweight,high-efficiency and high-absorbing electromagnetic interference(EMI)shielding composites is imperative in light of the worldwide promotion of sustainable manufacturing.In th...The utilization of eco-friendly,lightweight,high-efficiency and high-absorbing electromagnetic interference(EMI)shielding composites is imperative in light of the worldwide promotion of sustainable manufacturing.In this work,magnetic poly(butyleneadipate-coterephthalate)(PBAT)microspheres were firstly synthesized via phase separation method,then PBAT composite foams with layered structure was constructed through the supercritical carbon dioxide foaming and scraping techniques.The merits of integrating ferroferric oxideloaded multi-walled carbon nanotubes(Fe3O4@MWCNTs)nanoparticles,a microcellular framework,and a highly conductive silver layer have been judiciously orchestrated within this distinctive layered configuration.Microwaves are consumed throughout the process of“absorption-reflection-reabsorption”as much as possible,which greatly declines the secondary radiation pollution.The biodegradable PBAT composite foams achieved an EMI shielding effectiveness of up to 68 dB and an absorptivity of 77%,and authenticated favorable stabilization after the tape adhesion experiment.展开更多
Energy-storage systems and their production have attracted significant interest for practical applications.Batteries are the foundation of sustainable energy sources for electric vehicles(EVs),portable electronic devi...Energy-storage systems and their production have attracted significant interest for practical applications.Batteries are the foundation of sustainable energy sources for electric vehicles(EVs),portable electronic devices(PEDs),etc.In recent decades,Lithium-ion batteries(LIBs) have been extensively utilized in largescale energy storage devices owing to their long cycle life and high energy density.However,the high cost and limited availability of Li are the two main obstacles for LIBs.In this regard,sodium-ion batteries(SIBs) are attractive alternatives to LIBs for large-scale energy storage systems because of the abundance and low cost of sodium materials.Cathode is one of the most important components in the battery,which limits cost and performance of a battery.Among the classified cathode structures,layered structure materials have attracted attention because of their high ionic conductivity,fast diffusion rate,and high specific capacity.Here,we present a comprehensive review of the classification of layered structures and the preparation of layered materials.Furthermore,the review article discusses extensively about the issues of the layered materials,namely(1) electrochemical degradation,(2) irreversible structural changes,and(3) structural instability,and also it provides strategies to overcome the issues such as elemental phase composition,a small amount of elemental doping,structural design,and surface alteration for emerging SIBs.In addition,the article discusses about the recent research development on layered unary,binary,ternary,quaternary,quinary,and senary-based O3-and P2-type cathode materials for high-energy SIBs.This review article provides useful information for the development of high-energy layered sodium transition metal oxide P2 and O3-cathode materials for practical SIBs.展开更多
It has always been challenging work to reconcile the contradiction between the strength and plasticity of titanium materials.Laser powder bed fusion(LPBF) is a convenient method to fabricate innovative composites incl...It has always been challenging work to reconcile the contradiction between the strength and plasticity of titanium materials.Laser powder bed fusion(LPBF) is a convenient method to fabricate innovative composites including those inspired by gradient layered materials.In this work,we used LPBF to selectively prepare Ti N/Ti gradient layered structure(GLSTi)composites by using different N_(2)–Ar ratios during the LPBF process.We systematically investigated the mechanisms of in-situ synthesis Ti N,high strength and ductility of GLSTi composites using microscopic analysis,TEM characterization,and tensile testing with digital image correlation.Besides,a digital correspondence was established between the N_(2) concentration and the volume fraction of LPBF in-situ synthesized Ti N.Our results show that the GLSTi composites exhibit superior mechanical properties compared to pure titanium fabricated by LPBF under pure Ar.Specifically,the tensile strength of GLSTi was more than 1.5times higher than that of LPBF-formed pure titanium,reaching up to 1100 MPa,while maintaining a high elongation at fracture of 17%.GLSTi breaks the bottleneck of high strength but low ductility exhibited by conventional nanoceramic particle-strengthened titanium matrix composites,and the hetero-deformation induced strengthening effect formed by the Ti N/Ti layered structure explained its strength-plasticity balanced principle.The microhardness exhibits a jagged variation of the relatively low hardness of 245 HV0.2 for the pure titanium layer and a high hardness of 408 HV0.2 for the N_(2) in-situ synthesis layer.Our study provides a new concept for the structure-performance digital customization of 3D-printed Ti-based composites.展开更多
The balance between cationic redox and oxygen redox in layer-structured cathode materials is an important issue for sodium batteries to obtain high energy density and considerable cycle stability.Oxygen redox can cont...The balance between cationic redox and oxygen redox in layer-structured cathode materials is an important issue for sodium batteries to obtain high energy density and considerable cycle stability.Oxygen redox can contribute extra capacity to increase energy density,but results in lattice instability and capacity fading caused by lattice oxygen gliding and oxygen release.In this work,reversible Mn^(2+)/Mn^(4+)redox is realized in a P3-Na_(0.65)Li_(0.2)Co_(0.05)Mn_(0.75)O_(2)cathode material with high specific capacity and structure stability via Co substitution.The contribution of oxygen redox is suppressed significantly by reversible Mn^(2+)/Mn^(4+)redox without sacrificing capacity,thus reducing lattice oxygen release and improving the structure stability.Synchrotron X-ray techniques reveal that P3 phase is well maintained in a wide voltage window of 1.5-4.5 V vs.Na^(+)/Na even at 10 C and after long-term cycling.It is disclosed that charge compensation from Co/Mn-ions contributes to the voltage region below 4.2 V and O-ions contribute to the whole voltage range.The synergistic contributions of Mn^(2+)/Mn^(4+),Co^(2+)/Co^(3+),and O^(2-)/(O_n)^(2-)redox in P3-Na_(0.65)Li_(0.2)Co_(0.05)Mn_(0.75)O_(2)lead to a high reversible capacity of 215.0 m A h g^(-1)at 0.1 C with considerable cycle stability.The strategy opens up new opportunities for the design of high capacity cathode materials for rechargeable batteries.展开更多
Doping of rare earth elements into Bi_(4)Ti_(3)O_(12) can significantly enhance the upconversion photoluminescence(UCPL)properties,but its structure-property relationship is still unclear.In this work,Er-doped bismuth...Doping of rare earth elements into Bi_(4)Ti_(3)O_(12) can significantly enhance the upconversion photoluminescence(UCPL)properties,but its structure-property relationship is still unclear.In this work,Er-doped bismuth titanate Bi_(4-x)Er_(x)Ti_(3)O_(12)(x=0,0.1,0.2,0.3,0.4,0.5)ceramics were synthesized via solid-state reaction method.The x-ray diffraction analysis confirmed the orthorhombic crystalline structure of the Bi4-xErxTi_(3)O_(12) ceramics without any secondary phases.Experiments and calculations of positron annihilation spectroscopy were carried out to characterize their defect structure.The comparison between the experimental and calculated lifetime revealed that vacancy clusters were the main defects in the ceramics.The increase of the intensity of the second positron lifetime component(I_(2))of Bi_(3.5)Er_(0.5)Ti_(3)O_(12)ceramics indicated the presence of a high concentration of vacancy clusters.The UCPL spectra showed the sudden enhanced UCPL performance in Bi3.7Er0.3Ti3O12and Bi_(3.5)Er_(0.5)Ti_(3)O_(12)ceramics,which were consistent with the variation of the second positron lifetime component(I2).These results indicate that the enhanced UCPL properties are influenced not only by the concentrations of rare earth ions but also by the concentration of vacancy clusters present within the ceramics.展开更多
The Mg-air batteries face limitations with pronounced hydrogen evolution and low anodic utilization efficiency from Mg anodes in conventional NaCl electrolytes.The corrosion performance,surface composition,and dischar...The Mg-air batteries face limitations with pronounced hydrogen evolution and low anodic utilization efficiency from Mg anodes in conventional NaCl electrolytes.The corrosion performance,surface composition,and discharge properties of commercial purity Mg anodes were thoroughly investigated in KNO_(3)electrolytes with and without sodium 5-sulfosalicylate and compared to NaCl electrolyte.The addition of sodium 5-sulfosalicylate to KNO_(3)-based electrolyte results in efficient inhibition of H_(2)evolution,consequently enhancing anodic utilization efficiency to 84%and specific capacity to 1844 mAh/g,compared to NaCl(24%and 534 mAh/g,respectively)under discharge condition of 10 mA/cm^(2)in half cell.Furthermore,the chelating ability of sodium 5-sulfosalicylate can significantly improve the Mg surface dissolution kinetics and discharge product deposition rate at the Mg anode/electrolyte interface,yielding formation of a thinner discharge layer as confirmed by time-of-flight secondary ion mass spectrometry.The discharge voltage is increased to 1.60 V,compared to 1.35 V in KNO_(3)at 0.5 mA/cm^(2)in full cell.However,higher concentration of sodium 5-sulfosalicylate can accelerate Mg anode dissolution,impeding the improvement of anodic utilization efficiency,specific capacity,and energy density.Hence,determining optimal additive concentration and current density is crucial for enhancing the discharge properties of Mg-air batteries and mitigating excessive Mg dissolution in chloride-free electrolytes.展开更多
基金Project supported by the National Natural Science Foundation of china
文摘The velocity ratio of a free shear layer has an important influence on the spatial development of the large scale coherent structures in the layer. In this study, numerical simulations are performed to get an insight into this problem. The obtained numerical results agree quite well with those of a linear inviscid stability theory and the available experimental data.
基金Supported by the NNSF of China(10626017)the Science Foundation of the Education Committee of Heilongjiang Province(11511276)the Foundation of Heilongjiang Province(LBH-Q05114).
文摘A new computational algorithm is introduced for solving scattering problem in periodic structure. The PML technique is used to deal with the difficulty on truncating the unbounded domain while the DSC algorithm is utilized for the spatial discretization. The present study reveals that the method is efficient for solving the problem.
基金The project supported by National Natural Science Foundation of China (10632020, 10672017 and 20451057)
文摘Considering the mechnoelectrical coupling, the localization of SH-waves in disordered periodic layered piezoelectric structures is studied. The waves propagating in directions normal and tangential to the layers are considered. The transfer matrices between two consecutive unit cells are obtained according to the continuity conditions. The expressions of localization factor and localization length in the disordered periodic structures are presented. For the disordered periodic piezoelectric structures, the numerical results of localization factor and localization length are presented and discussed. It can be seen from the results that the frequency passbands and stopbands appear for the ordered periodic structures and the wave localization phenomenon occurs in the disordered periodic ones, and the larger the coefficient of variation is, the greater the degree of wave localization is. The widths of stopbands in the ordered periodic structures are very narrow when the properties of the consecutive piezoelectric materials are similar and the intervals of stopbands become broader when a certain material parameter has large changes. For the wave propagating in the direction normal to the layers the localization length has less dependence on the frequency, but for the wave propagating in the direction tangential to the layers the localization length is strongly dependent on the frequency.
基金supported by the National Natural Science Foundation of China (Nos.10672108,10572069 and 10820101048)
文摘This paper investigates shear horizontal （SH） waves propagating in a periodically layered structure that consists of piezoelectric （PE） layers perfectly bonded with piezomagnetic （PM） layers alternately. The explicit dispersion relations are derived for the two cases when the propagation directions of SH waves are normal to the interface and parallel to the interface, respectively. The asymptotic expressions for dispersion relations are also given when the wave number is extremely small. Numerical results for stop band effect and phase velocity are presented for a periodic system of alternating BaTiO3 and Terfenol-D layers. The influence of volume fraction on stop band effect and dispersion behaviors is discussed and revealed.
基金supported by the National 973 Key Development Program for Basic Research of China(S/N: 2006CB202308)the National Natural Science Foundation of China(Grant No.40972088)
文摘The Tazhong paleouplift is divided into the upper and the lower structural layers, bounded by the unconformity surface at the top of the Ordovician carbonate rock. The reservoirs in the two layers from different parts vary in number, type and reserves, but the mechanism was rarely researched before. Therefore, an explanation of the mechanism will promote petroleum exploration in Tazhong paleouplift. After studying the evolution and reservoir distribution of the Tazhong paleouplift, it is concluded that the evolution in late Caledonian, late Hercynian and Himalayan periods resulted in the upper and the lower structural layers. It is also defined that in the upper structural layer, structural and stratigraphic overlap reservoirs are developed at the top and the upper part of the paleouplift, which are dominated by oil reservoirs, while for the lower structural layer, lithological reservoirs are developed in the lower part of the paleouplift, which are dominated by gas reservoirs, and more reserves are discovered in the lower structural layer than the upper. Through a comparative analysis of accumulation conditions of the upper and the lower structural layers, the mechanism of enrichment differences is clearly explained. The reservoir and seal conditions of the lower structural layer are better than those of the upper layer, which is the reason why more reservoirs have been found in the former. The differences in the carrier system types, trap types and charging periods between the upper and the lower structural layers lead to differences in the reservoir types and distribution. An accumulation model is established for the Tazhong paleouplift. For the upper structural layer, the structural reservoirs and the stratigraphic overlap reservoirs are formed at the upper part of the paleouplift, while for the lower structural layer, the weathering crust reservoirs are formed at the top, the reef-flat reservoirs are formed on the lateral margin, the karst and inside reservoirs are formed in the lower part of the paleouplift.
基金Project supported by the National Natural Science Foundation of China(Nos.10132010 and 10072033)
文摘The propagation of surface acoustic waves in layered piezoelectric structureswith initial stresses is investigated. The phase velocity equations are obtained for electricallyfree and shorted cases, respectively. Effects of the initial stresses on the phase velocity and theelectromechanical coupling coefficient for the fundamental mode of the layered piezoelectricstructures are discussed. Numerical results for the c-axis oriented film of LiNbO_3 on a sapphiresubstrate are given. It is found that the fractional change in phase velocity is a linear functionwith the initial stresses, and the electromechanical coupling factor increases with an increase ofthe absolute values of the compressive initial stresses. The results are useful for the design ofsurface acoustic wave devices.
文摘Luquire et al. ' s impedance change model of a rectangular cross section probe coil above a structure with an arbitrary number of parallel layers was used to study the principle of measuring thicknesses of multi-layered structures in terms of eddy current testing voltage measurements. An experimental system for multi-layered thickness measurement was developed and several fitting models to formulate the relationships between detected impedance/voltage measurements and thickness are put forward using least square method. The determination of multi-layered thicknesses was investigated after inversing the voltage outputs of the detecting system. The best fitting and inversion models are presented.
基金supported by the National Natural Science Foundation of China (Grants 11332006,11272233,and 11411130150)the foundation from the China Scholarship Council (CSC) (Grant 201306250092)the Foundation Project for Outstanding Doctoral Dissertations of Tianjin University
文摘Nature has shown us that the microstructure of the skin of fast-swimming sharks in the ocean can reduce the skin friction drag due to the well-known shark-skin effect.In the present study,the effect of shark-skin-inspired riblets on coherent vortex structures in a turbulent boundary layer（TBL） is investigated.This is done by means of tomographic particle image velocimetry（TPIV） measurements in channel fl ws over an acrylic plate of drag-reducing riblets at a friction Reynolds number of 190.The turbulent fl ws over drag-reducing riblets are verifie by a planar time-resolved particle image velocimetry（TRPIV） system initially,and then the TPIV measurements are performed.Two-dimensional（2D） experimental results with a dragreduction rate of around 4.81% are clearly visible over triangle riblets with a peak-to-peak spacing s＋of 14,indicating from the drag-reducing performance that the buffer layer within the TBL has thickened;the logarithmic law region has shifted upward and the Reynolds shear stress decreased.A comparison of the spatial topological distributions of the spanwise vorticity of coherent vortex structures extracted at different wall-normal heights through the improved quadrant splitting method shows that riblets weaken the amplitudesof the spanwise vorticity when ejection（Q2） and sweep（Q4） events occur at the near wall,having the greatest effect on Q4 events in particular.The so-called quadrupole statistical model for coherent structures in the whole TBL is verified Meanwhile,their spatial conditional-averaged topological shapes and the spatial scales of quadrupole coherent vortex structures as a whole in the overlying turbulent fl w over riblets are changed,suggesting that the riblets dampen the momentum and energy exchange between the regions of near-wall and outer portion of the TBL by depressing the bursting events（Q2 and Q4）,thereby reducing the skin friction drag.
基金supported by the National Natural Science Foundation of China (90716008,10572004 and 10921202)MOST 973 Project (2009CB724100) and CSSA
文摘Discontinuous Galerkin（DG） method is known to have several advantages for flow simulations,in particular,in fiexible accuracy management and adaptability to mesh refinement. In the present work,the DG method is developed for numerical simulations of both temporally and spatially developing mixing layers. For the temporally developing mixing layer,both the instantaneous fiow field and time evolution of momentum thickness agree very well with the previous results. Shocklets are observed at higher convective Mach numbers and the vortex paring manner is changed for high compressibility. For the spatially developing mixing layer,large-scale coherent structures and self-similar behavior for mean profiles are investigated. The instantaneous fiow field for a three-dimensional compressible mixing layer is also reported,which shows the development of largescale coherent structures in the streamwise direction. All numerical results suggest that the DG method is effective in performing accurate numerical simulations for compressible shear fiows.
基金financially supported by the National Science Foundation of China(Nos.51572007 and 51622203),"Recruitment Program of Global Experts"
文摘2D nanosheets such as graphene, silicene, phosphorene, metal dichalcogenides and MXenes are emerging and promising for lithium storage due to their ultrathin nature and corresponding chemical/physical properties. However, the serious restacking and aggregation of the 2D nanosheets are still hampering their applications. To circumvent the issues of 2D nanosheets, one efficient strategy is to construct 3D structures with hierarchical porous structures, good chemical/mechanical stabilities and tunable electrical conductivities. In this review, we firstly focus on the available synthetic approaches of 3D structures from 2D nanosheets, and then summarize the relationships between the microstructures of 3D structures built from 2D nanosheets and their electrochemical behaviors for lithium storage. On the basis of above results, some challenges are briefly discussed in the perspective of the development of various functional 3D structures.
文摘In this paper, an experimental investigation on the flow structures in a turbulent bounda- ry layer employing a special laser light sheet-Hydrogen bubble flow visualization technique is described. It is observed that the high/low speed streaks are directly related to the hairpin or horseshoe-like vortices. This observation can give a better understanding of the physical mechanism in the turbulent boundary layer.
文摘The microstructural features of clacium rare earth(Ca RE) fluorocarbonate minerals from Southwest China were studied by using selected area electron diffraction(SAED) and high resolution transmission electron microscopy(HRTEM). Three new regularly mixed layer structures of B 8S 6 type with long period and different stacking sequence, i.e. B 8S 6 Ⅰ, B 8S 6 Ⅱ, and B 8S 6 Ⅲ, were found in the derived polycrystal of parisite, in which their structural symmetry, cell parameters, chemical formulas of crystal and stacking models of structural unit layer, etc. were determined. The results of this study also show that these new regularly mixed layer structrues were formed by order stacking unit layer of bastnaesite(B) and synchisite(S) in varying proportion along c axis. The observation under HRTEM reveals that in the three new regularly mixed layer structures there are different distribution modes of Ce F ion layers, CO 2- 3 ion groups between the Ce F ion layers, and CO 2- 3 ion groups between Ce F and Ca 2+ ion layers, and there are some heterogeneous textures, such as disorder interlayer and stacking fault. It further proves the complexity of the crystal structure of the Ca RE fluorocarbonate minerals.
文摘The coupling agents content and thickness on glass fiber (GF) surfaces which have been treated with silanes and titanates under different conditions are tested by means of XRF (X-Ray Fluorescent spectrometry). And the rheological characteristics of the dispersed systems prepared from the above glass fibers combined with unsaturated polyester resin (UP) are discussed. The results show that the rigidity of the internal layers of silane coupling agent absorbed by glass surfaces is greater than the one of the external layers; while the effect of the titanate coupling agents on the rheolo- gical characteristics of the system is approximately the same in each structural layer, that is due to the fact that both the internal and external layers of titanates on glass surfaces have the similar flexible structures.
基金This work was supported by the National Natural Science Foundation of China(No.U21A2093)the Anhui Provincial Natural Science Foundation(No.2308085QE146)the National Natural Science Foundation of Jiangsu Province(No.BK20210894).
文摘The utilization of eco-friendly,lightweight,high-efficiency and high-absorbing electromagnetic interference(EMI)shielding composites is imperative in light of the worldwide promotion of sustainable manufacturing.In this work,magnetic poly(butyleneadipate-coterephthalate)(PBAT)microspheres were firstly synthesized via phase separation method,then PBAT composite foams with layered structure was constructed through the supercritical carbon dioxide foaming and scraping techniques.The merits of integrating ferroferric oxideloaded multi-walled carbon nanotubes(Fe3O4@MWCNTs)nanoparticles,a microcellular framework,and a highly conductive silver layer have been judiciously orchestrated within this distinctive layered configuration.Microwaves are consumed throughout the process of“absorption-reflection-reabsorption”as much as possible,which greatly declines the secondary radiation pollution.The biodegradable PBAT composite foams achieved an EMI shielding effectiveness of up to 68 dB and an absorptivity of 77%,and authenticated favorable stabilization after the tape adhesion experiment.
基金supported by a grant from the Subway Fine Dust Reduction Technology Development Project of the Ministry of Land Infrastructure and Transport,Republic of Korea(21QPPWB152306-03)the Basic Science Research Capacity Enhancement Project through a Korea Basic Science Institute(National Research Facilities and Equipment Center)grant funded by the Ministry of Education of the Republic of Korea(2019R1A6C1010016)。
文摘Energy-storage systems and their production have attracted significant interest for practical applications.Batteries are the foundation of sustainable energy sources for electric vehicles(EVs),portable electronic devices(PEDs),etc.In recent decades,Lithium-ion batteries(LIBs) have been extensively utilized in largescale energy storage devices owing to their long cycle life and high energy density.However,the high cost and limited availability of Li are the two main obstacles for LIBs.In this regard,sodium-ion batteries(SIBs) are attractive alternatives to LIBs for large-scale energy storage systems because of the abundance and low cost of sodium materials.Cathode is one of the most important components in the battery,which limits cost and performance of a battery.Among the classified cathode structures,layered structure materials have attracted attention because of their high ionic conductivity,fast diffusion rate,and high specific capacity.Here,we present a comprehensive review of the classification of layered structures and the preparation of layered materials.Furthermore,the review article discusses extensively about the issues of the layered materials,namely(1) electrochemical degradation,(2) irreversible structural changes,and(3) structural instability,and also it provides strategies to overcome the issues such as elemental phase composition,a small amount of elemental doping,structural design,and surface alteration for emerging SIBs.In addition,the article discusses about the recent research development on layered unary,binary,ternary,quaternary,quinary,and senary-based O3-and P2-type cathode materials for high-energy SIBs.This review article provides useful information for the development of high-energy layered sodium transition metal oxide P2 and O3-cathode materials for practical SIBs.
基金supported by the Guangdong Basic and Applied Basic Research Foundation (2020B1515120013,2022B1515120066)National Natural Science Foundation of China (Nos.U2001218, 51875215)+1 种基金Key-Area Research and Development Program of Guangdong Province (2020B090923001)Special Support Foundation of Guangdong Province (No.2019TQ05Z110)。
文摘It has always been challenging work to reconcile the contradiction between the strength and plasticity of titanium materials.Laser powder bed fusion(LPBF) is a convenient method to fabricate innovative composites including those inspired by gradient layered materials.In this work,we used LPBF to selectively prepare Ti N/Ti gradient layered structure(GLSTi)composites by using different N_(2)–Ar ratios during the LPBF process.We systematically investigated the mechanisms of in-situ synthesis Ti N,high strength and ductility of GLSTi composites using microscopic analysis,TEM characterization,and tensile testing with digital image correlation.Besides,a digital correspondence was established between the N_(2) concentration and the volume fraction of LPBF in-situ synthesized Ti N.Our results show that the GLSTi composites exhibit superior mechanical properties compared to pure titanium fabricated by LPBF under pure Ar.Specifically,the tensile strength of GLSTi was more than 1.5times higher than that of LPBF-formed pure titanium,reaching up to 1100 MPa,while maintaining a high elongation at fracture of 17%.GLSTi breaks the bottleneck of high strength but low ductility exhibited by conventional nanoceramic particle-strengthened titanium matrix composites,and the hetero-deformation induced strengthening effect formed by the Ti N/Ti layered structure explained its strength-plasticity balanced principle.The microhardness exhibits a jagged variation of the relatively low hardness of 245 HV0.2 for the pure titanium layer and a high hardness of 408 HV0.2 for the N_(2) in-situ synthesis layer.Our study provides a new concept for the structure-performance digital customization of 3D-printed Ti-based composites.
基金financially supported by the National Key Scientific Research Project(2022YFB2502300)China and the National Natural Science Foundation of China(52071085)。
文摘The balance between cationic redox and oxygen redox in layer-structured cathode materials is an important issue for sodium batteries to obtain high energy density and considerable cycle stability.Oxygen redox can contribute extra capacity to increase energy density,but results in lattice instability and capacity fading caused by lattice oxygen gliding and oxygen release.In this work,reversible Mn^(2+)/Mn^(4+)redox is realized in a P3-Na_(0.65)Li_(0.2)Co_(0.05)Mn_(0.75)O_(2)cathode material with high specific capacity and structure stability via Co substitution.The contribution of oxygen redox is suppressed significantly by reversible Mn^(2+)/Mn^(4+)redox without sacrificing capacity,thus reducing lattice oxygen release and improving the structure stability.Synchrotron X-ray techniques reveal that P3 phase is well maintained in a wide voltage window of 1.5-4.5 V vs.Na^(+)/Na even at 10 C and after long-term cycling.It is disclosed that charge compensation from Co/Mn-ions contributes to the voltage region below 4.2 V and O-ions contribute to the whole voltage range.The synergistic contributions of Mn^(2+)/Mn^(4+),Co^(2+)/Co^(3+),and O^(2-)/(O_n)^(2-)redox in P3-Na_(0.65)Li_(0.2)Co_(0.05)Mn_(0.75)O_(2)lead to a high reversible capacity of 215.0 m A h g^(-1)at 0.1 C with considerable cycle stability.The strategy opens up new opportunities for the design of high capacity cathode materials for rechargeable batteries.
基金Project supported by the National Key Research and Development Program of China(Grant No.2019YFA0210000)the National Natural Science Foundation of China(Grant No.12175232)。
文摘Doping of rare earth elements into Bi_(4)Ti_(3)O_(12) can significantly enhance the upconversion photoluminescence(UCPL)properties,but its structure-property relationship is still unclear.In this work,Er-doped bismuth titanate Bi_(4-x)Er_(x)Ti_(3)O_(12)(x=0,0.1,0.2,0.3,0.4,0.5)ceramics were synthesized via solid-state reaction method.The x-ray diffraction analysis confirmed the orthorhombic crystalline structure of the Bi4-xErxTi_(3)O_(12) ceramics without any secondary phases.Experiments and calculations of positron annihilation spectroscopy were carried out to characterize their defect structure.The comparison between the experimental and calculated lifetime revealed that vacancy clusters were the main defects in the ceramics.The increase of the intensity of the second positron lifetime component(I_(2))of Bi_(3.5)Er_(0.5)Ti_(3)O_(12)ceramics indicated the presence of a high concentration of vacancy clusters.The UCPL spectra showed the sudden enhanced UCPL performance in Bi3.7Er0.3Ti3O12and Bi_(3.5)Er_(0.5)Ti_(3)O_(12)ceramics,which were consistent with the variation of the second positron lifetime component(I2).These results indicate that the enhanced UCPL properties are influenced not only by the concentrations of rare earth ions but also by the concentration of vacancy clusters present within the ceramics.
基金the China Scholarship Council(CSC)for funding(No.202209350006).
文摘The Mg-air batteries face limitations with pronounced hydrogen evolution and low anodic utilization efficiency from Mg anodes in conventional NaCl electrolytes.The corrosion performance,surface composition,and discharge properties of commercial purity Mg anodes were thoroughly investigated in KNO_(3)electrolytes with and without sodium 5-sulfosalicylate and compared to NaCl electrolyte.The addition of sodium 5-sulfosalicylate to KNO_(3)-based electrolyte results in efficient inhibition of H_(2)evolution,consequently enhancing anodic utilization efficiency to 84%and specific capacity to 1844 mAh/g,compared to NaCl(24%and 534 mAh/g,respectively)under discharge condition of 10 mA/cm^(2)in half cell.Furthermore,the chelating ability of sodium 5-sulfosalicylate can significantly improve the Mg surface dissolution kinetics and discharge product deposition rate at the Mg anode/electrolyte interface,yielding formation of a thinner discharge layer as confirmed by time-of-flight secondary ion mass spectrometry.The discharge voltage is increased to 1.60 V,compared to 1.35 V in KNO_(3)at 0.5 mA/cm^(2)in full cell.However,higher concentration of sodium 5-sulfosalicylate can accelerate Mg anode dissolution,impeding the improvement of anodic utilization efficiency,specific capacity,and energy density.Hence,determining optimal additive concentration and current density is crucial for enhancing the discharge properties of Mg-air batteries and mitigating excessive Mg dissolution in chloride-free electrolytes.
