This paper presents the results of a numerical investigation of micro-sized particle removal by droplet impact. Computational fluid dynamics simulation is used to calculate the flow distribution of droplet impact on a...This paper presents the results of a numerical investigation of micro-sized particle removal by droplet impact. Computational fluid dynamics simulation is used to calculate the flow distribution of droplet impact on a flat surface. The hydrodynamic forces exerted on the particle are then computed. Key factors controlling particle removal are discussed. Both hydrophilic and hydrophobic surfaces are considered. The flow distributions,especially the front edge expanding upon impact at microscale,strongly depend on surface wettability. The associated hydrodynamic forces on the particles vary accordingly. In addition, the impact on a dry surface can produce higher removal efficiency than that on a wet surface. Under the same impact conditions, the drag force exerted on a particle residing on a dry surface can be three orders of magnitudes larger than on a wet surface. Improving droplet impact velocity is more effective than improving droplet size.展开更多
In this paper, the lattice-Bohzmann method is used to investigate the droplet dynamics after impact on horizontal and inclined solid surface. The two-phase interparticle potential model is employed. The model is found...In this paper, the lattice-Bohzmann method is used to investigate the droplet dynamics after impact on horizontal and inclined solid surface. The two-phase interparticle potential model is employed. The model is found to possess a linear relation between the macroscopic properties （ surface tension σ and contact angle α） and microscopic parameters （ G, G, ）. The flow state of the droplet on the surface is analyzed in detail, and the effects of surface characteristic, impact velocity, impact angle, the viscosity and surface tension of the liquid are investigated, respectively. It is shown that the lattice-Bohzmann method can not only track exactly and automatically the interface, but also the simulation results have a good qualitative agreement with ones of the previous experimental and numerical studies.展开更多
In this study,we numerically investigate the droplet impact onto a thin liquid film deposited on a structured surface with square pillars and cavities.The time evolution of crown geometry is strongly affected by the s...In this study,we numerically investigate the droplet impact onto a thin liquid film deposited on a structured surface with square pillars and cavities.The time evolution of crown geometry is strongly affected by the surface structure.When the thickness of the liquid film is larger than the structure height,the expanding speed of the crown base radius is independent of the structure width.However,if the liquid film thickness is equal to the structure height,the crown base expands slower as the structure width increases.Surface structures have strong effects on the crown height and radius,and can prevent ejected filament from breaking into satellite droplets for certain cases.For the liquid film with the thickness equal to the pillar height,both the crown height and the radius exhibit non-monotonic behaviors as the pillar width increases.There exists one pillar width which produces the smallest crown height and the largest crown radius.展开更多
The phenomenon of droplet impact on an immiscible liquid is encountered in a variety of scenarios in nature and industrial production. Despite exhaustive research, it is not fully clear how the immiscibility of the li...The phenomenon of droplet impact on an immiscible liquid is encountered in a variety of scenarios in nature and industrial production. Despite exhaustive research, it is not fully clear how the immiscibility of the liquid on which a droplet impacts affects the crown evolution. The present work experimentally investigates the evolution kinematics of a crown formed by the normal impact of a camellia oil droplet on an immiscible water layer. Based on discussion of dynamic impact behaviors for three critical Weber numbers(We), the radius of the crown and its average spreading velocity are compared with those of previous theoretical models to discuss their applicability to the immiscible liquid. The evolution kinematics(morphology and velocity) are analyzed by considering the effects of the We and layer thickness. Furthermore,the ability of crown expansion in radial and vertical directions is characterized by a velocity ratio. The results show that our experimental crown radius still follows a square-root function of evolution time, which agrees with the theoretical predictions. The dimensionless average spreading velocity decreases with We and follows a multivariate power law, while the dimensionless average rising velocity remains constant. The velocity ratio is shown to linearly increase with We,demonstrating that the rising movement in crown evolution gradually enhances with We. These results are helpful for further investigation on the droplet impact on an immiscible liquid layer.展开更多
The interaction of single water droplet impacting on immiscible liquid surface was focused with the temperature varying from 50℃ to 210℃.The impact behavior is recorded with a high-speed camera running at 2000 frame...The interaction of single water droplet impacting on immiscible liquid surface was focused with the temperature varying from 50℃ to 210℃.The impact behavior is recorded with a high-speed camera running at 2000 frames per second.It is found that droplet diameter,oil temperature,andWeber number have important influences on impact behaviors.Three typical phenomena,including penetration,crater-jet,and crater-jet–secondary jet,were observed.Penetration only occurs when the Weber number is below 105.With Weber number increasing to 302,the jet begins to appear.Moreover,to gain deeper physical insight into the crater formation and jet formation,the energy of droplet impingement onto the liquid pool surface was estimated.The oil temperature has a significant effect on the energy conversion efficiency.High temperature is beneficial to improve energy conversion efficiency.展开更多
The deformation characteristics of the cavity due to droplet impact on a water surface are experimentally investigated.Dimensional analysis shows that the characteristic values of time,depth,and horizontal diameter ca...The deformation characteristics of the cavity due to droplet impact on a water surface are experimentally investigated.Dimensional analysis shows that the characteristic values of time,depth,and horizontal diameter can be taken as 10^(-3)times the ratio of surface tension to the product of viscosity coefficient and gravitational acceleration,the maximum depth,and the maximum horizontal diameter,respectively.The evolutions of the dimensionless cavity sizes for different values of Weber number(We)coincide for 220<We<686.A partial-sphere model of cavity is established based on experimental observations.Energy models are then derived,and the energy conversions are calculated to identify the relationship between these conversions and cavity deformation.It is found that the kinetic energy model established under the hypothesis proposed by Leng is no longer applicable when the dimensionless time t^(*)<3.5,owing to deviations from the geometric model.展开更多
A droplet undergoes spreading,rebounding or splashing when it impacts solid boundary,which is a typical phenomenon of free surface flow that exists widely in modern industry.Smoothed particle hydrodynamics(SPH)method ...A droplet undergoes spreading,rebounding or splashing when it impacts solid boundary,which is a typical phenomenon of free surface flow that exists widely in modern industry.Smoothed particle hydrodynamics(SPH)method is applied to numerically study the dynamical behaviors of the droplet impacting solid boundary,and both the spreading and rebounding phenomena of the droplet are reproduced in the simulation.The droplet deformation,flow fields and pressure fields inside the droplet at different moments are analyzed.Two important factors,the initial velocity and diameter,are discussed in determining the maximum spreading factor,revealing that the maximum spreading factor increases with the increase of the impact velocity and droplet diameter respectively.展开更多
We have investigated experimentally the process of a droplet impact on a regular micro-grooved surface. The target surfaces are patterned such that micro-scale spokes radiate from the center, concentric circles, and p...We have investigated experimentally the process of a droplet impact on a regular micro-grooved surface. The target surfaces are patterned such that micro-scale spokes radiate from the center, concentric circles, and parallel lines on the polishing copper plate, using Quasi-LIGA molding technology. The dynamic behavior of water droplets impacting on these structured surfaces is examined using a high-speed camera, including the drop impact processes, the maximum spreading diameters, and the lengths and numbers of fingers at different values of Weber number. Experimental results validate that the spreading processes are arrested on all target surfaces at low velocity. Also, the experimental results at higher impact velocity demonstrate that the spreading process is conducted on the surface parallel to the micro-grooves, but is arrested in the direction perpendicular to the micro-grooves. Besides, the lengths of fingers increase observably, even when they are ejected out as tiny droplets along the groove direction, at the same time the drop recoil velocity is reduced by micro-grooves which are parallel to the spreading direction, but not by micro-grooves which are vertical to the spreading direction.展开更多
Robust superhydrophobic surfaces with excellent capacities of repelling water and anti-frosting are of importance for many mechanical components.In this work,wear-resistant superhydrophobic surfaces were fabricated by...Robust superhydrophobic surfaces with excellent capacities of repelling water and anti-frosting are of importance for many mechanical components.In this work,wear-resistant superhydrophobic surfaces were fabricated by curing a mixture of polyurethane acrylate(PUA)coating and 1H,1H,2H,2H-Perfluorodecyltrichlorosilane(HFTCS)on titanium alloy(TC4)surfaces decorated with micropillars pattern,thus,composite functional surfaces with PUA coating in the valleys around the micropillars pattern of TC4 were achieved.Apparent contact angle on fabricated surfaces could reach 167°.Influences of the geometric parameters of micropillars pattern on the apparent contact angle were investigated,and the corresponding wear-resistant property was compared.Droplet impact and anti-frosting performances on the prepared surfaces were highlighted.An optimized design of surface texture with robust superhydrophobicity,controllable droplet impact,and anti-frosting performances was proposed.This design principle is of promising prospects for fabricating superhydrophobic surfaces in traditional mechanical systems.展开更多
Droplet impacting liquid surface is not only the extremely prevalent phenomenon in the nature and industrial production but also the extremely complicated problem of strong non-linear transient impact and free-surface...Droplet impacting liquid surface is not only the extremely prevalent phenomenon in the nature and industrial production but also the extremely complicated problem of strong non-linear transient impact and free-surface flow. On the basis of the two-dimensional viscous incompressible N-S equations, this paper conducts a study of numerical simulation on the problem of droplet impacting liquid surface （water beads） of water container in certain initial velocity by the method of SPH （smoothed particle hydrodynamics）. The effect of surface tension is considered between surface particles by searching the free surface particles in the course of study; the effect of initial impact has been solved by use of artificial viscosity; at the same time, the side-wall virtual particles and image virtual particles are both introduced to deal with the boundary condition, which has solved the boundary defects quite well and eliminated the instability of real particles dropped to the comer of container. The calculated results form the distribution chart of particles, flow field chart, pressure chart and the displacement and velocity variation curve of different particles. The comparison between simulated results and experimental photos shows that the simulation is effective. This paper compares the variational curves for fluctuations of liquid surface qualitatively through adopting the methods of level-set, BEM and SPH, respectively at last. The simulated results show that it will produce strong non-linear phenomena, such as the splash of liquid, discrete liquid surface, and strong wave of free liquid surface, when the droplet impacts liquid surface; in the course of impacting, the movement of liquid particles exhibits the characteristic of oscillation; the method of SPH has certain advantages of dealing with the large deformation problem of free surface.展开更多
We experimentally studied droplet impact dynamics onto wing feathers of kingfishers. Distilled water droplets with a fixed diameter of 2.06 mm were used as drop liquid and the initial impact velocities of droplets var...We experimentally studied droplet impact dynamics onto wing feathers of kingfishers. Distilled water droplets with a fixed diameter of 2.06 mm were used as drop liquid and the initial impact velocities of droplets varied from 0.28 m· s^-1 to 1.60 m·s^-1. Two high-speed cameras were utilized to capture the impact process of water droplets onto the wing feather surface from both horizontal and vertical directions. Two states of the feathers （elastic and inelastic） were considered to study the influence of elasticity. At the entire impact ve- locity range we studied, regular rebound, bubble trapping and jetting, partial pinning and partial rebound of droplets on inelastic wing feather surface were observed as the initial impact velocity increased. However, only one dynamic behavior （regular rebound） was found on the elastic wing feather surface. The elasticity plays a more important role in the direction difference of droplet spreading than wing feather microstructure. The contact time of water droplets on the elastic wing feather surface was less than that on the inelastic surface within the range of Web numbers from 1.06 to 36 under test conditions.展开更多
The normal impingement process of two water droplets upon a thin film on the solid surface was numerically investigated. The numerical treatment was based on the finite volume solution of the Navier-Stokes （N-S） equ...The normal impingement process of two water droplets upon a thin film on the solid surface was numerically investigated. The numerical treatment was based on the finite volume solution of the Navier-Stokes （N-S） equations combined with the volume of fluid method （VOF）. Physically reasonable results for the process of two droplets impacting on the thin film were obtained. The effects of the droplet velocity, the fihn thickness and the spacing between the two droplets on the splash and spread process of the impact were examined.展开更多
Partial coalescence is a complicated flow phenomenon.In the present study,the coalescence process is simulated with the volume of fluid(VOF)method.The numerical results reveal that a downward high-velocity region play...Partial coalescence is a complicated flow phenomenon.In the present study,the coalescence process is simulated with the volume of fluid(VOF)method.The numerical results reveal that a downward high-velocity region plays a significant role in partial coalescence.The high-velocity region pulls the droplet downward continuously which is an important factor for the droplet turning into a prolate shape and the final pinch-off.The shift from partial coalescence to full coalescence is explained based on the droplet shape before the pinch-off.With the droplet impact velocity increasing,the droplet shape will get close to a sphere before the pinch-off.When the shape gets close enough to a sphere,the partial coalescence shifts to full coalescence.The effect of film thickness on the coalescence process is also investigated.With large film thickness,partial coalescence happens,while with small film thickness,full coalescence happens.In addition,the results indicate that the critical droplet impact velocity increases with the increase of surface tension coefficient but decreases with the increase of viscosity and initial droplet diameter.And there is a maximum critical Weber number with the increase of surface tension coefficient and initial droplet diameter.展开更多
In the current study,a two-dimensional multi-relaxation time(MRT)lattice Boltzmann model which can tolerate high density ratios and low viscosity is employed to simulate the liquid droplet impact onto a curved target....In the current study,a two-dimensional multi-relaxation time(MRT)lattice Boltzmann model which can tolerate high density ratios and low viscosity is employed to simulate the liquid droplet impact onto a curved target.The temporal variation of the film thickness at the north pole of the target surface is investigated.Three different temporal phases of the dynamics behavior,namely,the initial drop deformation phase,the inertia dominated phase and the viscosity dominated phase are reproduced and studied.The effect of the Reynolds number,Weber number and Galilei number on the film flow dynamics is investigated.In addition,the dynamic behavior of the droplet impact onto the side of the curved target is shown,and the effect of the contact angle,the Reynolds number and the Weber number are investigated.展开更多
With some popular tracking methods for free surface, simulations of several typical examples are carried out under various flow field conditions. The results show that the Smoothed Particle Hydrodynamics （SPH） metho...With some popular tracking methods for free surface, simulations of several typical examples are carried out under various flow field conditions. The results show that the Smoothed Particle Hydrodynamics （SPH） method is very suitable in simulating the flow problems with a free surface. A viscous liquid droplet with an initial velocity impacting on a solid surface is simulated based on the SPH method, and the surface tension is considered by searching the free surface particles, the initial impact effect is considered by using the artificial viscosity method, boundary virtual particles and image virtual particles are introduced to deal with the boundary problem, and the boundary defect can be identified quite well. The comparisons of simulated results and experimental photographs show that the SPH method can not only exactly simulate the spreading process and the rebound process of a liquid droplet impacting on a solid surface but also accurately track the free surface particles, simulate the free-surface flow and determine the shape of the free surface due to its particle nature.展开更多
In order to investigate the material corrosion by liquid droplet solid impact, a nonlinear coupling wave model adopted to analyze the impact between the spherical liquid droplet and an elastic solid plane has been dev...In order to investigate the material corrosion by liquid droplet solid impact, a nonlinear coupling wave model adopted to analyze the impact between the spherical liquid droplet and an elastic solid plane has been developed. Many usable results such as the dimensionless pressure in the contact plane of liquid solid and inside the liquid droplet, the equivalent stress distribution inside the solid, the effect of solid elasticity on the impact, and the locations of the maximum equivalent stress in different...展开更多
This paper presents a computational fluid dynamics approach for micro droplet impacting on a flat dry surface. A two-phase flow approach is employed using FLUENT VOF multiphase model to calculate the flow distribution...This paper presents a computational fluid dynamics approach for micro droplet impacting on a flat dry surface. A two-phase flow approach is employed using FLUENT VOF multiphase model to calculate the flow distributions upon impact. The contact line velocity is tracked to calculate the dynamic contact angle through user defined function program. The study showed that the treatment of contact line velocity is crucial for the accurate prediction of droplet impacting on poor wettability surfaces. On the other hand, it has much less influence on the simulation of droplet impacting on good wettability surfaces. Good fit between simulation results and experimental data is obtained using this model.展开更多
A thermal multiphase lattice Boltzmann(LB) model is used to study the behavior of droplet impact on hot surface and the relevant heat transfer properties.After validating the correctness of the codes through the D^(2)...A thermal multiphase lattice Boltzmann(LB) model is used to study the behavior of droplet impact on hot surface and the relevant heat transfer properties.After validating the correctness of the codes through the D^(2) law,the simulations of intrinsic contact angle and the temperature-dependent surface tension are performed.The LB model is then used to simulate the droplet impact on smooth and micro-hole heated surface.On the smooth surface,the impinging droplet is reluctant to rebound,unless the intrinsic wettability of the solid surface is fairly good.On the micro-hole surface,however,the micro-holes provide favorable sites for generating a high-pressure vapor cushion underneath the impinging droplet,which thereby facilitates the continuous droplet rebound.For the continuously rebounding droplet.The time evolution of volume and temperature display obvious oscillations.The achievable height of the rebounding droplet increases as the intrinsic wettability of the solid surface becomes better,and the maximum transient heat flux is found to be directly proportional to the droplet rebounding height.Within a certain time interval,the continuous rebounding behavior of the droplet is favorable for enhancing the total heat quantity/heat transfer efficiency,and the influence of intrinsic wettability on the total heat during droplet impingement is greater than that of the superheat.The LB simulations not only present different states of droplets on hot surfaces,but also guide the design of the micro-hole surface with desirable heat transfer properties.展开更多
文摘This paper presents the results of a numerical investigation of micro-sized particle removal by droplet impact. Computational fluid dynamics simulation is used to calculate the flow distribution of droplet impact on a flat surface. The hydrodynamic forces exerted on the particle are then computed. Key factors controlling particle removal are discussed. Both hydrophilic and hydrophobic surfaces are considered. The flow distributions,especially the front edge expanding upon impact at microscale,strongly depend on surface wettability. The associated hydrodynamic forces on the particles vary accordingly. In addition, the impact on a dry surface can produce higher removal efficiency than that on a wet surface. Under the same impact conditions, the drag force exerted on a particle residing on a dry surface can be three orders of magnitudes larger than on a wet surface. Improving droplet impact velocity is more effective than improving droplet size.
基金Sponsored by the National Nature Science Foundation of China(Grant No.51276030,51176017)
文摘In this paper, the lattice-Bohzmann method is used to investigate the droplet dynamics after impact on horizontal and inclined solid surface. The two-phase interparticle potential model is employed. The model is found to possess a linear relation between the macroscopic properties （ surface tension σ and contact angle α） and microscopic parameters （ G, G, ）. The flow state of the droplet on the surface is analyzed in detail, and the effects of surface characteristic, impact velocity, impact angle, the viscosity and surface tension of the liquid are investigated, respectively. It is shown that the lattice-Bohzmann method can not only track exactly and automatically the interface, but also the simulation results have a good qualitative agreement with ones of the previous experimental and numerical studies.
基金Project supported by the National Natural Science Foundation of China(Nos.11988102,91848201,11872004,and 11802004)
文摘In this study,we numerically investigate the droplet impact onto a thin liquid film deposited on a structured surface with square pillars and cavities.The time evolution of crown geometry is strongly affected by the surface structure.When the thickness of the liquid film is larger than the structure height,the expanding speed of the crown base radius is independent of the structure width.However,if the liquid film thickness is equal to the structure height,the crown base expands slower as the structure width increases.Surface structures have strong effects on the crown height and radius,and can prevent ejected filament from breaking into satellite droplets for certain cases.For the liquid film with the thickness equal to the pillar height,both the crown height and the radius exhibit non-monotonic behaviors as the pillar width increases.There exists one pillar width which produces the smallest crown height and the largest crown radius.
基金Project supported by the Natural Science Foundation of Zhejiang Province of China(Grant No. LY15E060007)Innovation Ability Promotion of Science&Technology SMEs of Shandong Province,China(Grant No. 2021TSGC1339)。
文摘The phenomenon of droplet impact on an immiscible liquid is encountered in a variety of scenarios in nature and industrial production. Despite exhaustive research, it is not fully clear how the immiscibility of the liquid on which a droplet impacts affects the crown evolution. The present work experimentally investigates the evolution kinematics of a crown formed by the normal impact of a camellia oil droplet on an immiscible water layer. Based on discussion of dynamic impact behaviors for three critical Weber numbers(We), the radius of the crown and its average spreading velocity are compared with those of previous theoretical models to discuss their applicability to the immiscible liquid. The evolution kinematics(morphology and velocity) are analyzed by considering the effects of the We and layer thickness. Furthermore,the ability of crown expansion in radial and vertical directions is characterized by a velocity ratio. The results show that our experimental crown radius still follows a square-root function of evolution time, which agrees with the theoretical predictions. The dimensionless average spreading velocity decreases with We and follows a multivariate power law, while the dimensionless average rising velocity remains constant. The velocity ratio is shown to linearly increase with We,demonstrating that the rising movement in crown evolution gradually enhances with We. These results are helpful for further investigation on the droplet impact on an immiscible liquid layer.
基金Project supported by the National Key Research and Development Program of China(Grant No.2017YFC0805100)the Fundamental Research Funds for the Central Universities of China(Grant No.PA2020GDGP0052).
文摘The interaction of single water droplet impacting on immiscible liquid surface was focused with the temperature varying from 50℃ to 210℃.The impact behavior is recorded with a high-speed camera running at 2000 frames per second.It is found that droplet diameter,oil temperature,andWeber number have important influences on impact behaviors.Three typical phenomena,including penetration,crater-jet,and crater-jet–secondary jet,were observed.Penetration only occurs when the Weber number is below 105.With Weber number increasing to 302,the jet begins to appear.Moreover,to gain deeper physical insight into the crater formation and jet formation,the energy of droplet impingement onto the liquid pool surface was estimated.The oil temperature has a significant effect on the energy conversion efficiency.High temperature is beneficial to improve energy conversion efficiency.
基金supported by the National Natural Science Foundation of China(11872271)the Major Scientific and Technological Projects of Tianjin(18ZXRHSF00270).
文摘The deformation characteristics of the cavity due to droplet impact on a water surface are experimentally investigated.Dimensional analysis shows that the characteristic values of time,depth,and horizontal diameter can be taken as 10^(-3)times the ratio of surface tension to the product of viscosity coefficient and gravitational acceleration,the maximum depth,and the maximum horizontal diameter,respectively.The evolutions of the dimensionless cavity sizes for different values of Weber number(We)coincide for 220<We<686.A partial-sphere model of cavity is established based on experimental observations.Energy models are then derived,and the energy conversions are calculated to identify the relationship between these conversions and cavity deformation.It is found that the kinetic energy model established under the hypothesis proposed by Leng is no longer applicable when the dimensionless time t^(*)<3.5,owing to deviations from the geometric model.
基金Supported by the National Natural Science Foundation of China(No.51079095)the Science Fund for Creative Research Groups of the National Natural Science Foundation of China(No.51021004)
文摘A droplet undergoes spreading,rebounding or splashing when it impacts solid boundary,which is a typical phenomenon of free surface flow that exists widely in modern industry.Smoothed particle hydrodynamics(SPH)method is applied to numerically study the dynamical behaviors of the droplet impacting solid boundary,and both the spreading and rebounding phenomena of the droplet are reproduced in the simulation.The droplet deformation,flow fields and pressure fields inside the droplet at different moments are analyzed.Two important factors,the initial velocity and diameter,are discussed in determining the maximum spreading factor,revealing that the maximum spreading factor increases with the increase of the impact velocity and droplet diameter respectively.
基金supported by the National Natural Science Foundation of China(Grant No.51109178)the Science and Technology Innovation Foundation of Northwestern Polytechnical University,China(Grant No.JC20120218)
文摘We have investigated experimentally the process of a droplet impact on a regular micro-grooved surface. The target surfaces are patterned such that micro-scale spokes radiate from the center, concentric circles, and parallel lines on the polishing copper plate, using Quasi-LIGA molding technology. The dynamic behavior of water droplets impacting on these structured surfaces is examined using a high-speed camera, including the drop impact processes, the maximum spreading diameters, and the lengths and numbers of fingers at different values of Weber number. Experimental results validate that the spreading processes are arrested on all target surfaces at low velocity. Also, the experimental results at higher impact velocity demonstrate that the spreading process is conducted on the surface parallel to the micro-grooves, but is arrested in the direction perpendicular to the micro-grooves. Besides, the lengths of fingers increase observably, even when they are ejected out as tiny droplets along the groove direction, at the same time the drop recoil velocity is reduced by micro-grooves which are parallel to the spreading direction, but not by micro-grooves which are vertical to the spreading direction.
基金support provided by the National Natural Science Foundation of China(No.51805252)the Tribology Science Fund of State Key Laboratory of Tribology(No.SKLTKF21B02)the Alexander von Humboldt Foundation.
文摘Robust superhydrophobic surfaces with excellent capacities of repelling water and anti-frosting are of importance for many mechanical components.In this work,wear-resistant superhydrophobic surfaces were fabricated by curing a mixture of polyurethane acrylate(PUA)coating and 1H,1H,2H,2H-Perfluorodecyltrichlorosilane(HFTCS)on titanium alloy(TC4)surfaces decorated with micropillars pattern,thus,composite functional surfaces with PUA coating in the valleys around the micropillars pattern of TC4 were achieved.Apparent contact angle on fabricated surfaces could reach 167°.Influences of the geometric parameters of micropillars pattern on the apparent contact angle were investigated,and the corresponding wear-resistant property was compared.Droplet impact and anti-frosting performances on the prepared surfaces were highlighted.An optimized design of surface texture with robust superhydrophobicity,controllable droplet impact,and anti-frosting performances was proposed.This design principle is of promising prospects for fabricating superhydrophobic surfaces in traditional mechanical systems.
基金supported by the National Natural Science Foundation of China (Grant Nos. 51079095, 51021004)
文摘Droplet impacting liquid surface is not only the extremely prevalent phenomenon in the nature and industrial production but also the extremely complicated problem of strong non-linear transient impact and free-surface flow. On the basis of the two-dimensional viscous incompressible N-S equations, this paper conducts a study of numerical simulation on the problem of droplet impacting liquid surface （water beads） of water container in certain initial velocity by the method of SPH （smoothed particle hydrodynamics）. The effect of surface tension is considered between surface particles by searching the free surface particles in the course of study; the effect of initial impact has been solved by use of artificial viscosity; at the same time, the side-wall virtual particles and image virtual particles are both introduced to deal with the boundary condition, which has solved the boundary defects quite well and eliminated the instability of real particles dropped to the comer of container. The calculated results form the distribution chart of particles, flow field chart, pressure chart and the displacement and velocity variation curve of different particles. The comparison between simulated results and experimental photos shows that the simulation is effective. This paper compares the variational curves for fluctuations of liquid surface qualitatively through adopting the methods of level-set, BEM and SPH, respectively at last. The simulated results show that it will produce strong non-linear phenomena, such as the splash of liquid, discrete liquid surface, and strong wave of free liquid surface, when the droplet impacts liquid surface; in the course of impacting, the movement of liquid particles exhibits the characteristic of oscillation; the method of SPH has certain advantages of dealing with the large deformation problem of free surface.
基金This study was supported by the National Natural Science Foundation of China （Grant Nos. 51575227 and 51706084）, the National Key Research and Develop- ment Program of China （Grant No. 2016YFE0132900）, the Science and Technology Project of Jilin Provincial Education Department （Grant No. JJKH20170795K2）, and the Science and Technology Development Program of Jilin Province （Grant No. 172411GG010040701）.
文摘We experimentally studied droplet impact dynamics onto wing feathers of kingfishers. Distilled water droplets with a fixed diameter of 2.06 mm were used as drop liquid and the initial impact velocities of droplets varied from 0.28 m· s^-1 to 1.60 m·s^-1. Two high-speed cameras were utilized to capture the impact process of water droplets onto the wing feather surface from both horizontal and vertical directions. Two states of the feathers （elastic and inelastic） were considered to study the influence of elasticity. At the entire impact ve- locity range we studied, regular rebound, bubble trapping and jetting, partial pinning and partial rebound of droplets on inelastic wing feather surface were observed as the initial impact velocity increased. However, only one dynamic behavior （regular rebound） was found on the elastic wing feather surface. The elasticity plays a more important role in the direction difference of droplet spreading than wing feather microstructure. The contact time of water droplets on the elastic wing feather surface was less than that on the inelastic surface within the range of Web numbers from 1.06 to 36 under test conditions.
基金Project supported by the Shanghai Leading Academic Discipline Project (Grant No.Y0103)
文摘The normal impingement process of two water droplets upon a thin film on the solid surface was numerically investigated. The numerical treatment was based on the finite volume solution of the Navier-Stokes （N-S） equations combined with the volume of fluid method （VOF）. Physically reasonable results for the process of two droplets impacting on the thin film were obtained. The effects of the droplet velocity, the fihn thickness and the spacing between the two droplets on the splash and spread process of the impact were examined.
基金the National Natural Science Foundation of China(Grant No.51876102)the Science Fund for Creative Research Groups of the National Natural Science Foundation of China(Grant No.51621062).
文摘Partial coalescence is a complicated flow phenomenon.In the present study,the coalescence process is simulated with the volume of fluid(VOF)method.The numerical results reveal that a downward high-velocity region plays a significant role in partial coalescence.The high-velocity region pulls the droplet downward continuously which is an important factor for the droplet turning into a prolate shape and the final pinch-off.The shift from partial coalescence to full coalescence is explained based on the droplet shape before the pinch-off.With the droplet impact velocity increasing,the droplet shape will get close to a sphere before the pinch-off.When the shape gets close enough to a sphere,the partial coalescence shifts to full coalescence.The effect of film thickness on the coalescence process is also investigated.With large film thickness,partial coalescence happens,while with small film thickness,full coalescence happens.In addition,the results indicate that the critical droplet impact velocity increases with the increase of surface tension coefficient but decreases with the increase of viscosity and initial droplet diameter.And there is a maximum critical Weber number with the increase of surface tension coefficient and initial droplet diameter.
基金the financial support for this work by the UK Engineering and Physical Sciences Research Council(EPSRC)project grant:EP/K036548/1 and the EU FP7 IPACTS(268696)and iComFluid Projects(312261).
文摘In the current study,a two-dimensional multi-relaxation time(MRT)lattice Boltzmann model which can tolerate high density ratios and low viscosity is employed to simulate the liquid droplet impact onto a curved target.The temporal variation of the film thickness at the north pole of the target surface is investigated.Three different temporal phases of the dynamics behavior,namely,the initial drop deformation phase,the inertia dominated phase and the viscosity dominated phase are reproduced and studied.The effect of the Reynolds number,Weber number and Galilei number on the film flow dynamics is investigated.In addition,the dynamic behavior of the droplet impact onto the side of the curved target is shown,and the effect of the contact angle,the Reynolds number and the Weber number are investigated.
基金Project supported by the National Natural Science Foundation of China(Grant No.51079095)the Science Fund for Creative Research Groups of the National Natural Science Foundation of China(Grant No.51021004)
文摘With some popular tracking methods for free surface, simulations of several typical examples are carried out under various flow field conditions. The results show that the Smoothed Particle Hydrodynamics （SPH） method is very suitable in simulating the flow problems with a free surface. A viscous liquid droplet with an initial velocity impacting on a solid surface is simulated based on the SPH method, and the surface tension is considered by searching the free surface particles, the initial impact effect is considered by using the artificial viscosity method, boundary virtual particles and image virtual particles are introduced to deal with the boundary problem, and the boundary defect can be identified quite well. The comparisons of simulated results and experimental photographs show that the SPH method can not only exactly simulate the spreading process and the rebound process of a liquid droplet impacting on a solid surface but also accurately track the free surface particles, simulate the free-surface flow and determine the shape of the free surface due to its particle nature.
基金Natural Science Foundation of Xi'an Jiaotong University (5 73 0 2 7)
文摘In order to investigate the material corrosion by liquid droplet solid impact, a nonlinear coupling wave model adopted to analyze the impact between the spherical liquid droplet and an elastic solid plane has been developed. Many usable results such as the dimensionless pressure in the contact plane of liquid solid and inside the liquid droplet, the equivalent stress distribution inside the solid, the effect of solid elasticity on the impact, and the locations of the maximum equivalent stress in different...
基金the financial support from Grace Semiconductor Manufacturing Corporation
文摘This paper presents a computational fluid dynamics approach for micro droplet impacting on a flat dry surface. A two-phase flow approach is employed using FLUENT VOF multiphase model to calculate the flow distributions upon impact. The contact line velocity is tracked to calculate the dynamic contact angle through user defined function program. The study showed that the treatment of contact line velocity is crucial for the accurate prediction of droplet impacting on poor wettability surfaces. On the other hand, it has much less influence on the simulation of droplet impacting on good wettability surfaces. Good fit between simulation results and experimental data is obtained using this model.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.51901148 and 51874204)the Fund of the State Key Laboratory of Solidification Processing(Northwestern Polytechnical University),China(Grant No.SKLSP202006)。
文摘A thermal multiphase lattice Boltzmann(LB) model is used to study the behavior of droplet impact on hot surface and the relevant heat transfer properties.After validating the correctness of the codes through the D^(2) law,the simulations of intrinsic contact angle and the temperature-dependent surface tension are performed.The LB model is then used to simulate the droplet impact on smooth and micro-hole heated surface.On the smooth surface,the impinging droplet is reluctant to rebound,unless the intrinsic wettability of the solid surface is fairly good.On the micro-hole surface,however,the micro-holes provide favorable sites for generating a high-pressure vapor cushion underneath the impinging droplet,which thereby facilitates the continuous droplet rebound.For the continuously rebounding droplet.The time evolution of volume and temperature display obvious oscillations.The achievable height of the rebounding droplet increases as the intrinsic wettability of the solid surface becomes better,and the maximum transient heat flux is found to be directly proportional to the droplet rebounding height.Within a certain time interval,the continuous rebounding behavior of the droplet is favorable for enhancing the total heat quantity/heat transfer efficiency,and the influence of intrinsic wettability on the total heat during droplet impingement is greater than that of the superheat.The LB simulations not only present different states of droplets on hot surfaces,but also guide the design of the micro-hole surface with desirable heat transfer properties.
