Discharge coefficients of 3-in-1 hole of three inclination angles and three spacing between holes are presented which described the discharge behavior of a row of holes. The inlet and outlet of the 3-in-1 hole both ha...Discharge coefficients of 3-in-1 hole of three inclination angles and three spacing between holes are presented which described the discharge behavior of a row of holes. The inlet and outlet of the 3-in-1 hole both have a 15° lateral expansion. The flow conditions considered are mainstream turbulence intensities and density ratios of secondary flow to mainstream. The momentum flux ratios varied in the range from 1 to 4. The comparison is made of the discharge coefficients of three shaped holes to find an optimal hole with low flow loss. The results show that the discharge coefficients of 3-in- 1 hole are highest in three shaped holes and therefore this article is focused on the measurements of discharge coefficients of 3-in-1 hole for various geometries and aerodynamic parameters. The measured results of 3-in-1 hole indicate that turbulence intensities, density ratios and momentum flux ratios have weak influence on discharge coefficients for inclination angle of 20°. The high turbulence intensity yields the small discharge coefficients for inclination angle of 45° and 90°. The increased both momentum flux ratios and density ratios lead to the increased discharge coefficients for inclination angle of 45° and 90°. The increased inclination angle causes the rapidly increased discharge coefficients. There is a weak dependence of discharge coefficients on hole pitches.展开更多
This paper details the results of a joint project between Rolls-Royce Deutschland (RRD) and the Northwestern Polytechnical University of China (NWPU). The objective of the project was the determination of the influenc...This paper details the results of a joint project between Rolls-Royce Deutschland (RRD) and the Northwestern Polytechnical University of China (NWPU). The objective of the project was the determination of the influence of tabulators in turbine blade cooling passages on film hole discharge coefficients (Cd coefficients). A large-scale plexiglas model was used by the NWPU to measure the turbulator influence on Cd coefficients for a wide range of different geometrical parameters, Reynolds numbers and cooling flow off take ratios. RRD specified the comprehensive test matrix and analysed the test data. The CFD code FLUENT was used by RRD for numerical simulation of the test cases with the main objective to support the interpretation of observed trends. Both, experimental and numerical results will be presented in this paper for a selection of test configurations.展开更多
An experimental investigation into pre-swirl effectiveness and receiver hole discharge coefficient characteristics for a high radius injection pre-swirl cooling systems was carried out on a physically representative e...An experimental investigation into pre-swirl effectiveness and receiver hole discharge coefficient characteristics for a high radius injection pre-swirl cooling systems was carried out on a physically representative experimental rig with a 450 mm diameter rotor.The receiver holes and pre-swirl nozzle were located at a radius of 181 mm and 180 mm respectively.The experimental work was mainly conducted at 5 000～12 000 r/min,4 bar absolute pressure and 1.132 kg/s air supply.The maximum air supply temperature was 190 ℃.Pressure and temperature distributions in the pre-swirl system were examined with an emphasis on the velocity effectiveness of the pre-swirl system as a whole and on the discharge coefficients of the rotating 'receiver holes' in the rotor.The results showed that the velocity effectiveness increased with increasing swirl ratio resulting in reduced blade cooling flow temperature.Different seal flow configurations caused very different effectiveness at different speeds,but outflow through the inner and outer seals always gave the highest effectiveness compared other configurations.Increasing the seal flow rate reduced the effectiveness.For the coefficient of discharge,except for the low speed range,it increased with increase in swirl ratio for most speeds.展开更多
文摘Discharge coefficients of 3-in-1 hole of three inclination angles and three spacing between holes are presented which described the discharge behavior of a row of holes. The inlet and outlet of the 3-in-1 hole both have a 15° lateral expansion. The flow conditions considered are mainstream turbulence intensities and density ratios of secondary flow to mainstream. The momentum flux ratios varied in the range from 1 to 4. The comparison is made of the discharge coefficients of three shaped holes to find an optimal hole with low flow loss. The results show that the discharge coefficients of 3-in- 1 hole are highest in three shaped holes and therefore this article is focused on the measurements of discharge coefficients of 3-in-1 hole for various geometries and aerodynamic parameters. The measured results of 3-in-1 hole indicate that turbulence intensities, density ratios and momentum flux ratios have weak influence on discharge coefficients for inclination angle of 20°. The high turbulence intensity yields the small discharge coefficients for inclination angle of 45° and 90°. The increased both momentum flux ratios and density ratios lead to the increased discharge coefficients for inclination angle of 45° and 90°. The increased inclination angle causes the rapidly increased discharge coefficients. There is a weak dependence of discharge coefficients on hole pitches.
文摘This paper details the results of a joint project between Rolls-Royce Deutschland (RRD) and the Northwestern Polytechnical University of China (NWPU). The objective of the project was the determination of the influence of tabulators in turbine blade cooling passages on film hole discharge coefficients (Cd coefficients). A large-scale plexiglas model was used by the NWPU to measure the turbulator influence on Cd coefficients for a wide range of different geometrical parameters, Reynolds numbers and cooling flow off take ratios. RRD specified the comprehensive test matrix and analysed the test data. The CFD code FLUENT was used by RRD for numerical simulation of the test cases with the main objective to support the interpretation of observed trends. Both, experimental and numerical results will be presented in this paper for a selection of test configurations.
文摘An experimental investigation into pre-swirl effectiveness and receiver hole discharge coefficient characteristics for a high radius injection pre-swirl cooling systems was carried out on a physically representative experimental rig with a 450 mm diameter rotor.The receiver holes and pre-swirl nozzle were located at a radius of 181 mm and 180 mm respectively.The experimental work was mainly conducted at 5 000～12 000 r/min,4 bar absolute pressure and 1.132 kg/s air supply.The maximum air supply temperature was 190 ℃.Pressure and temperature distributions in the pre-swirl system were examined with an emphasis on the velocity effectiveness of the pre-swirl system as a whole and on the discharge coefficients of the rotating 'receiver holes' in the rotor.The results showed that the velocity effectiveness increased with increasing swirl ratio resulting in reduced blade cooling flow temperature.Different seal flow configurations caused very different effectiveness at different speeds,but outflow through the inner and outer seals always gave the highest effectiveness compared other configurations.Increasing the seal flow rate reduced the effectiveness.For the coefficient of discharge,except for the low speed range,it increased with increase in swirl ratio for most speeds.
