The effect of Al3+, NH, Na+ on the Ti content in the preparation of Ti-ZSM-5 by the isomorphous substitution of ZSM-5 using gaseous TiCl4 as titanium resource has been investigated. It is surprisingly found that altho...The effect of Al3+, NH, Na+ on the Ti content in the preparation of Ti-ZSM-5 by the isomorphous substitution of ZSM-5 using gaseous TiCl4 as titanium resource has been investigated. It is surprisingly found that although the direct ratio exists between the Ti content and the content of the skeletal Al: y=0.08x2+0.57x+1.23(here y represents TiO2% and x represents Al2O3%). but the catalytic activities of Ti-ZSM-5 for the oxidation of styrene sharply rise with the decrease of TiO2%. The skeletal Al hinders the Ti incorporation into the framework of molecular sieves characterized by FT-IR technique. At the same . NH ion has no effect on the Ti incorporation. but Na+ ion does.展开更多
Ti is regarded as one of the promising grain refiners in cast Al-Li-Cu alloys,but few research works have been done on its independent role.In this study,the effect of Ti on the microstructure evolution and mechanical...Ti is regarded as one of the promising grain refiners in cast Al-Li-Cu alloys,but few research works have been done on its independent role.In this study,the effect of Ti on the microstructure evolution and mechanical properties of cast Al-2Li-2Cu-0.5Mg base alloy was investigated.The results revealed that the grains can be prominently refined with the increase of Ti addition.After adding Ti,high density TiB_(2)-Al_(3)Ti composite particles with a low lattice misfit form as heterogeneous nucleation sites for the α-Al matrix.δ’(Al3Li) and T_(1)(Al_(2)CuLi) precipitates that provide enhanced strength are dominated in the alloys after T6 aging treatment.The average size of both δ’ and half-width of δ’-precipitation free zone(PFZ) decreases gradually with the increase of Ti content.This is because the higher binding energy between Ti atoms and vacancies limits the diffusion efficiency of Li atoms,and thus results in a higher ductility.Additionally,no nano-sized Al_(3)Ti or core-shell structure of Al_(3)(Li,Ti) particles are found.The tensile property test results indicate that the Al-2Li-2Cu-0.5Mg alloy achieves optimal properties after aging at 175 °C for 32 h when 0.15wt.% Ti is added.It exhibits a yield strength of 352±5 MPa,an ultimate tensile strength of 423±6 MPa,and an elongation of(3±0.4)%.These findings are expected to offer a reliable theoretical guidance for the industrial composition design of the Al-Li-Cu series cast alloys.展开更多
The microstructure and mechanical properties of Ti(C, N)-based cermets with different content Mo were studied. Different Mo contents were added into Ti(C, N)-based cermets. Effect of sintering temperature on mechanica...The microstructure and mechanical properties of Ti(C, N)-based cermets with different content Mo were studied. Different Mo contents were added into Ti(C, N)-based cermets. Effect of sintering temperature on mechanical properties of the cermets was also investigated. Specimens were fabricated by conventional powder metallurgy techniques and vacuum sintered at different temperatures. The microstructure and the fracture morphology were investigated using scanning electron microscope. Transverse strength and hardness were measured. The results show that the microstructure is uniform and the thickness of rim phase is moderate when the content of Mo is 8%. The mechanical properties are the best when the content of Mo is 8% and the sintering temperature is 1450℃.展开更多
文摘The effect of Al3+, NH, Na+ on the Ti content in the preparation of Ti-ZSM-5 by the isomorphous substitution of ZSM-5 using gaseous TiCl4 as titanium resource has been investigated. It is surprisingly found that although the direct ratio exists between the Ti content and the content of the skeletal Al: y=0.08x2+0.57x+1.23(here y represents TiO2% and x represents Al2O3%). but the catalytic activities of Ti-ZSM-5 for the oxidation of styrene sharply rise with the decrease of TiO2%. The skeletal Al hinders the Ti incorporation into the framework of molecular sieves characterized by FT-IR technique. At the same . NH ion has no effect on the Ti incorporation. but Na+ ion does.
基金financially supported by the National Natural Science Foundation of China (Nos.51821001 and 51871148)。
文摘Ti is regarded as one of the promising grain refiners in cast Al-Li-Cu alloys,but few research works have been done on its independent role.In this study,the effect of Ti on the microstructure evolution and mechanical properties of cast Al-2Li-2Cu-0.5Mg base alloy was investigated.The results revealed that the grains can be prominently refined with the increase of Ti addition.After adding Ti,high density TiB_(2)-Al_(3)Ti composite particles with a low lattice misfit form as heterogeneous nucleation sites for the α-Al matrix.δ’(Al3Li) and T_(1)(Al_(2)CuLi) precipitates that provide enhanced strength are dominated in the alloys after T6 aging treatment.The average size of both δ’ and half-width of δ’-precipitation free zone(PFZ) decreases gradually with the increase of Ti content.This is because the higher binding energy between Ti atoms and vacancies limits the diffusion efficiency of Li atoms,and thus results in a higher ductility.Additionally,no nano-sized Al_(3)Ti or core-shell structure of Al_(3)(Li,Ti) particles are found.The tensile property test results indicate that the Al-2Li-2Cu-0.5Mg alloy achieves optimal properties after aging at 175 °C for 32 h when 0.15wt.% Ti is added.It exhibits a yield strength of 352±5 MPa,an ultimate tensile strength of 423±6 MPa,and an elongation of(3±0.4)%.These findings are expected to offer a reliable theoretical guidance for the industrial composition design of the Al-Li-Cu series cast alloys.
文摘The microstructure and mechanical properties of Ti(C, N)-based cermets with different content Mo were studied. Different Mo contents were added into Ti(C, N)-based cermets. Effect of sintering temperature on mechanical properties of the cermets was also investigated. Specimens were fabricated by conventional powder metallurgy techniques and vacuum sintered at different temperatures. The microstructure and the fracture morphology were investigated using scanning electron microscope. Transverse strength and hardness were measured. The results show that the microstructure is uniform and the thickness of rim phase is moderate when the content of Mo is 8%. The mechanical properties are the best when the content of Mo is 8% and the sintering temperature is 1450℃.
