The effects of the Cr3C2 content and wheel speed on the amorphization behavior of the melt-spun SmCo7-x（Cr3C2）x （x=0.10-0.25） alloys were studied systematically by X-ray diffraction analysis （XRD）, differential ...The effects of the Cr3C2 content and wheel speed on the amorphization behavior of the melt-spun SmCo7-x（Cr3C2）x （x=0.10-0.25） alloys were studied systematically by X-ray diffraction analysis （XRD）, differential scanning calorimetry （DSC） and magnetic measurements. The ribbon melt-spun at lower wheel speed （20 m/s） has composite structure composed of mostly SmCo7 and a small amount of Sm2Co17R. The grain size of SmCo7 phase decreases with the increase of Cr3C2 content. With the increase of wheel speed, the XRD peaks become lower and accompanied with a broad increase in backgrounds, indicating a considerable decrease in the grain size of the SmCo7 phase. When the wheel speed increases to 40 m/s, SmCo7-x（Cr3C2）x alloys can be obtained in the amorphous state for 0.15≤x≤0.25 with intrinsic coercive Hci of 0.004-0.007 T. The DSC analysis reveals that SmCo7 phase firstly precipitates from the amorphous matrix at 650 °C, followed by the crystallization of Sm2Co17 phase at 770 °C.展开更多
In order to counteract the demagnetization caused by eddy current loss,widespread attention has been devoted to increasing the resistivity of permanent magnets.We prepared 2:17-type Sm Co magnets doped with different ...In order to counteract the demagnetization caused by eddy current loss,widespread attention has been devoted to increasing the resistivity of permanent magnets.We prepared 2:17-type Sm Co magnets doped with different ZrO_(2)contents and investigated the influence of the ZrO_(2)content on the magnetic properties and resistive anisotropism.The results showed that not only was the resistivity of the magnet improved,but,in addition,the coercivity of the magnet was significantly increased.The microstructure was studied with TEM,which showed that ZrO_(2)doping was able to cause a decrease in the lamellar phase density and the growth of cellular structures.The increased grain boundaries and Sm_(2)O_(3)phases were favorable to the improvement of resistivity.The decrease of the lamellar phases caused a narrowing of the resistive anisotropism.The additional Cu in the center of the cellular boundaries was the main reason for the enhancement of Hcj.However,an excessive amount caused an increase of the Zr_6(Fe Co)_(23)phase and a deterioration of the cellular structure,thereby leading to a decrease in coercivity.展开更多
In order to ameliorate the electrochemical hydrogen storage performance of La-Mg-Ni system A2B7-type electrode alloys, a small amount of Si was added. The La0.8Mg0.2Ni3.3Co0.2Six （x=0-0.2） electrode alloys were prep...In order to ameliorate the electrochemical hydrogen storage performance of La-Mg-Ni system A2B7-type electrode alloys, a small amount of Si was added. The La0.8Mg0.2Ni3.3Co0.2Six （x=0-0.2） electrode alloys were prepared by casting and annealing. The effects of adding Si on the structure and electrochemical hydrogen storage characteristics of the alloys were investigated systematically. The results indicate that the as-cast and annealed alloys hold multiple structures, involving two major phases of （La, Mg）2Ni7 with a Ce2Ni7-type hexagonal structure and LaNi5 with a CaCu5-type hexagonal structure as well as one residual phase LaNi3. The addition of Si results in a decrease in （La, Mg）2Ni7 phase and an increase in LaNi5 phase without changing the phase structure of the alloys. What is more, it brings on an obvious effect on electrochemical hydrogen storage characteristics of the alloys. The discharge capacities of the as-cast and annealed alloys decline with the increase of Si content, but their cycle stabilities clearly grow under the same condition. Furthermore, the measurements of the high rate discharge ability, the limiting current density, hydrogen diffusion coefficient as well as electrochemical impedance spectra all indicate that the electrochemical kinetic properties of the electrode alloys first increase and then decrease with the rising of Si content.展开更多
The casting and annealing technologies were applied to fabricate the La0.8Mg0.2Ni3.3Co0.2Six （x = 0-0.2） electrode alloys. The effects of Si content and annealing temperature on the structure and electrochemical per...The casting and annealing technologies were applied to fabricate the La0.8Mg0.2Ni3.3Co0.2Six （x = 0-0.2） electrode alloys. The effects of Si content and annealing temperature on the structure and electrochemical performances of the alloys were investigated systematically. The analyses of XRD and SEM show that all the alloys possess a multiphase structure, involving two main phases （La, Mg）2Ni7 and LaNi5 as well as a residual phase LaNi3. The addition of Si brings on an evident increase in the LaNi5 phase and a decrease in the （La, Mg）2Ni7 phase, without altering the main phase component of the alloy, which also makes the lattice constants and cell volumes of the alloy enlarged. Likewise, the annealing treatment engenders the same action on the lattice constants and cell volumes as adding Si. Simultaneously, it gives rise to the variation of the phase abundance and the coarsening of the alloy grains. The electrochemical measurements indicate that the addition of Si ameliorates the cycle stability of the as-cast and annealed alloys significantly, but impairs their discharge capacities clearly. Similarly, the annealing treatment makes a positive contribution to the cycle stability of the alloy evidently, and the discharge capacity of the alloy shows a maximum value with annealing temperature rising. Furthermore, the high rate discharge ability （HR） first augments and then declines with the rising of Si content and annealing temperature.展开更多
In order to improve the cyclic stability of La-Mg-Ni system （Ce2Ni7-type） alloy electrode, small amount of Co was added in La0.75Mg0.25Ni3.5 alloy. The effect of Co on electrochemical performance and microstructure ...In order to improve the cyclic stability of La-Mg-Ni system （Ce2Ni7-type） alloy electrode, small amount of Co was added in La0.75Mg0.25Ni3.5 alloy. The effect of Co on electrochemical performance and microstructure of the alloys were investigated in detail. XRD results showed that the alloys had multiphase structure composed of （La, Mg）2Ni7, LaNi5 and small amount of LaNi2 phases. The discharge capacity of the alloys first increased and then decreased with increasing Co content. At a discharge current density of 900 mA/g, the HRD of the alloy electrodes increased from 81.3% （x=0） to 89.2 % （x=0.2）, and then reduced to 87.8 % （x=0.6）. After 60 charge/discharge cycles, the capacity retention rate of the alloys enhanced from 52.67% to 61.32%, and the capacity decay rate of the alloys decreased from 2.60 to 2.05 mAh/g per cycle with increasing Co content. The obtained results by XPS and XRD showed that the fundamental reasons for the capacity decay of the La-Mg-Ni system （Ce2Ni7-type） alloy electrodes were corrosion and oxidation as well as passivation of Mg and Lain alkaline solution.展开更多
Investigation of alloy structure shows that La2-xMgxNi7 （x = 0.3 - 0.8） alloys are mainly com- posed of Ce/Ni7-type, Gd2Co7-type and PuNi3-type phase. The influence of Mg content in alloys on the phase structure is ...Investigation of alloy structure shows that La2-xMgxNi7 （x = 0.3 - 0.8） alloys are mainly com- posed of Ce/Ni7-type, Gd2Co7-type and PuNi3-type phase. The influence of Mg content in alloys on the phase structure is great, resulting in a linear decrease of the unit cell parameters of main phases and increase of hydrogen absorption/desorption plateau as Mg content increases. Electrochemical measurements show that as the Mg content increases, the discharge capacity of alloy electrodes first increases and then decreases. The cyclic stability presents a deteriorative trend. La1.4Mg0.6 Ni7 alloy electrode exhibits the maximum electrochemical discharge capacity （378 mAh·g^-1）, and the La1.6Mg0.4Ni7 alloy electrode shows the best cyclic stability （S270 = 81%）.展开更多
Bulk nanocrystalline SmCo6Fe sintered magnet was prepared by Spark Plasma Sintering technique (SPS). XRD patterns show that the magnet exhibits a stable TbCu7 structure. TEM observation indicates that the microstructu...Bulk nanocrystalline SmCo6Fe sintered magnet was prepared by Spark Plasma Sintering technique (SPS). XRD patterns show that the magnet exhibits a stable TbCu7 structure. TEM observation indicates that the microstructure of the magnet is composed of SmCo6Fe single phase grains with an average grain size of 30 nm. Magnetic measurement shows that under 9 T magnetic field, the coercivity of the magnet reaches 1.12 T; the saturation magnetization and the remanence are 1.13 and 0.67 T, respectively. The magnet has a (BH)max of 75.6 kJ·cm-3.展开更多
The partial substitution of Zr for La has been performed in order to ameliorate the electrochemical hydrogen storage performances of La–Mg–Ni based A2B7-type electrode alloys. The melt spinning technology was used t...The partial substitution of Zr for La has been performed in order to ameliorate the electrochemical hydrogen storage performances of La–Mg–Ni based A2B7-type electrode alloys. The melt spinning technology was used to prepare the La0.75-xZrxMg0.25Ni3.2Co0.2Al0.1 (x=0, 0.05, 0.1, 0.15, 0.2) electrode alloys. The impacts of the melt spinning and the substituting La with Zr on the structures and the electrochemical hydrogen storage characteristics of the alloys were systemically investigated. The analysis of XRD and TEM reveals that the as-cast and spun alloys have a multiphase structure, composing of two main phases (La, Mg)2Ni7 and LaNi5 as well as a residual phase LaNi2. The electrochemical measurement indicates that both the substitution of Zr for La and the melt spinning ameliorate the electrochemical cycle stability of the alloys dramatically. Furthermore, the high rate discharge ability (HRD) of the as-spun (10 m/s) alloys notably declines with growing the amount of Zr substitution, while it first augments and then falls for the (x=0.1) alloy with rising the spinning rate.展开更多
To improve the cyclic stability of La-Mg-Ni system alloy, as-cast La0.75Mg0.25Ni3.5Co0.2 alloy was annealed at 1123, 1223, and 1323 K for 10 h in 0.3 MPa argon. The microstructure and electrochemical performance of di...To improve the cyclic stability of La-Mg-Ni system alloy, as-cast La0.75Mg0.25Ni3.5Co0.2 alloy was annealed at 1123, 1223, and 1323 K for 10 h in 0.3 MPa argon. The microstructure and electrochemical performance of different annealed alloys were investigated systematically by X-Ray Diffraction （XRD）, Scanning Electron Microscopy （SEM）, X-Ray Photoelectron Spectroscopy （XPS）, and electrochemical experiments. The results obtained by XRD and SEM showed that the as-cast and annealed （1123 K） alloys had multiphase structure containing LaNis, （La, Mg）2（Ni, Co）7 and few LaNi2 phases. When annealing temperatures approached 1223 and 1323 K, LaNi2 phase disappeared. The annealed alloys at 1223 and 1323 K were composed of LaNi5, （La, Mg）2（Ni, Co）7 and （La, Mg）（Ni, Co）3 phases. With increasing annealing temperature, the maximum discharge capacity of the alloy decreased monotonously, but the cyclic stability was improved owing to structure homogeneity and grain growth after annealing, as well as the enhancement of anti-oxidation/corrosion ability and the suppression of pulverization during cycling in KOH electrolyte.展开更多
In order to ameliorate the electrochemical hydrogen storage performances of La-Mg–Ni system A_2B_7-type electrode alloys, the partial substitution of M (M = Zr, Pr) for La was performed. The melt spinning technology ...In order to ameliorate the electrochemical hydrogen storage performances of La-Mg–Ni system A_2B_7-type electrode alloys, the partial substitution of M (M = Zr, Pr) for La was performed. The melt spinning technology was used to fabricate the La_(0.75-x)M_xMg_0.25Ni_3.2Co_0.2Al_0.1 (M = Zr, Pr; x = 0, 0.1) electrode alloys. The influences of the melt spinning and substituting La with M (M = Zr, Pr) on the structures and the electrochemical hydrogen storage characteristics of the alloys were investigated. The analysis of XRD, SEM, and TEM reveals that the as-cast and spun alloys have a multiphase structure composed of two main phases (La, Mg)_2Ni_7 and LaNi_5 as well as a residual phase LaNi_2 . The as-spun (M = Pr) alloy displays an entire nanocrystalline structure, while an amorphous-like structure is detected in the as-spun (M = Zr) alloy, implying that the substitution of Zr for La facilitates the amorphous formation. The electrochemical measurements exhibit that the substitution of Pr for La clearly increases the discharge capacity of the alloys; however, the Zr substitution brings on an adverse impact. Meanwhile, the M (M = Zr, Pr) substitution significantly enhances its cycle stability. The melt spinning exerts an evident effect on the electrochemical performances of the alloys, whose discharge capacity and high rate discharge ability (HRD) first mount up and then fall with the growing spinning rate, whereas their cycle stabilities monotonously augment as the spinning rate increases.展开更多
The La-Mg-Ni system A2B7-type electrode alloys with nominal composition La0.75-xZrxMg0.25Ni3.2Co0.2Al0.1(x=0,0.05, 0.1,0.15,0.2)were prepared by casting and melt-spinning.The influences of melt spinning on the electro...The La-Mg-Ni system A2B7-type electrode alloys with nominal composition La0.75-xZrxMg0.25Ni3.2Co0.2Al0.1(x=0,0.05, 0.1,0.15,0.2)were prepared by casting and melt-spinning.The influences of melt spinning on the electrochemical performances as well as the structures of the alloys were investigated.The results obtained by XRD,SEM and TEM show that the as-cast and spun alloys have a multiphase structure,consisting of two main phases(La,Mg)Ni3 and LaNi5 as well as a residual phase LaNi2.The melt spinning leads to an obvious increase of the LaNi5 phase and a decrease of the(La,Mg)Ni3 phase in the alloys.The results of the electrochemical measurement indicate that the discharge capacity of the alloys(x≤0.1)first increases and then decreases with the increase of spinning rate,whereas for x>0.1,the discharge capacity of the alloys monotonously falls.The melt spinning slightly impairs the activation capability of the alloys,but it significantly enhances the cycle stability of the alloys.展开更多
基金Project (51104188) supported by the National Natural Science Foundation for Young Scholars of China
文摘The effects of the Cr3C2 content and wheel speed on the amorphization behavior of the melt-spun SmCo7-x（Cr3C2）x （x=0.10-0.25） alloys were studied systematically by X-ray diffraction analysis （XRD）, differential scanning calorimetry （DSC） and magnetic measurements. The ribbon melt-spun at lower wheel speed （20 m/s） has composite structure composed of mostly SmCo7 and a small amount of Sm2Co17R. The grain size of SmCo7 phase decreases with the increase of Cr3C2 content. With the increase of wheel speed, the XRD peaks become lower and accompanied with a broad increase in backgrounds, indicating a considerable decrease in the grain size of the SmCo7 phase. When the wheel speed increases to 40 m/s, SmCo7-x（Cr3C2）x alloys can be obtained in the amorphous state for 0.15≤x≤0.25 with intrinsic coercive Hci of 0.004-0.007 T. The DSC analysis reveals that SmCo7 phase firstly precipitates from the amorphous matrix at 650 °C, followed by the crystallization of Sm2Co17 phase at 770 °C.
基金the National Natural Science Foundation of China(Grant No.51877094)Ningbo Science and Technology Project(Grant No.2014B11009)。
文摘In order to counteract the demagnetization caused by eddy current loss,widespread attention has been devoted to increasing the resistivity of permanent magnets.We prepared 2:17-type Sm Co magnets doped with different ZrO_(2)contents and investigated the influence of the ZrO_(2)content on the magnetic properties and resistive anisotropism.The results showed that not only was the resistivity of the magnet improved,but,in addition,the coercivity of the magnet was significantly increased.The microstructure was studied with TEM,which showed that ZrO_(2)doping was able to cause a decrease in the lamellar phase density and the growth of cellular structures.The increased grain boundaries and Sm_(2)O_(3)phases were favorable to the improvement of resistivity.The decrease of the lamellar phases caused a narrowing of the resistive anisotropism.The additional Cu in the center of the cellular boundaries was the main reason for the enhancement of Hcj.However,an excessive amount caused an increase of the Zr_6(Fe Co)_(23)phase and a deterioration of the cellular structure,thereby leading to a decrease in coercivity.
基金Projects(50961009,51161015)supported by the National Natural Science Foundation of ChinaProject(2011AA03A408)supported by the High-tech Research and Development Program of ChinaProjects(2011ZD10,2010ZD05)supported by the Natural Science Foundation of Inner Mongolia,China
文摘In order to ameliorate the electrochemical hydrogen storage performance of La-Mg-Ni system A2B7-type electrode alloys, a small amount of Si was added. The La0.8Mg0.2Ni3.3Co0.2Six （x=0-0.2） electrode alloys were prepared by casting and annealing. The effects of adding Si on the structure and electrochemical hydrogen storage characteristics of the alloys were investigated systematically. The results indicate that the as-cast and annealed alloys hold multiple structures, involving two major phases of （La, Mg）2Ni7 with a Ce2Ni7-type hexagonal structure and LaNi5 with a CaCu5-type hexagonal structure as well as one residual phase LaNi3. The addition of Si results in a decrease in （La, Mg）2Ni7 phase and an increase in LaNi5 phase without changing the phase structure of the alloys. What is more, it brings on an obvious effect on electrochemical hydrogen storage characteristics of the alloys. The discharge capacities of the as-cast and annealed alloys decline with the increase of Si content, but their cycle stabilities clearly grow under the same condition. Furthermore, the measurements of the high rate discharge ability, the limiting current density, hydrogen diffusion coefficient as well as electrochemical impedance spectra all indicate that the electrochemical kinetic properties of the electrode alloys first increase and then decrease with the rising of Si content.
基金Funded by National Natural Science Foundations of China(Nos.51161015 and 51371094)National 863 Plans Projects of China(No.2011AA03A408)
文摘The casting and annealing technologies were applied to fabricate the La0.8Mg0.2Ni3.3Co0.2Six （x = 0-0.2） electrode alloys. The effects of Si content and annealing temperature on the structure and electrochemical performances of the alloys were investigated systematically. The analyses of XRD and SEM show that all the alloys possess a multiphase structure, involving two main phases （La, Mg）2Ni7 and LaNi5 as well as a residual phase LaNi3. The addition of Si brings on an evident increase in the LaNi5 phase and a decrease in the （La, Mg）2Ni7 phase, without altering the main phase component of the alloy, which also makes the lattice constants and cell volumes of the alloy enlarged. Likewise, the annealing treatment engenders the same action on the lattice constants and cell volumes as adding Si. Simultaneously, it gives rise to the variation of the phase abundance and the coarsening of the alloy grains. The electrochemical measurements indicate that the addition of Si ameliorates the cycle stability of the as-cast and annealed alloys significantly, but impairs their discharge capacities clearly. Similarly, the annealing treatment makes a positive contribution to the cycle stability of the alloy evidently, and the discharge capacity of the alloy shows a maximum value with annealing temperature rising. Furthermore, the high rate discharge ability （HR） first augments and then declines with the rising of Si content and annealing temperature.
基金the National Natural Science Foundation of China (50701011)Natural Science Foundation of Inner Mongolia, China (200711020703)Science and Technology Planned Project of Inner Mongolia, China (20050205)
文摘In order to improve the cyclic stability of La-Mg-Ni system （Ce2Ni7-type） alloy electrode, small amount of Co was added in La0.75Mg0.25Ni3.5 alloy. The effect of Co on electrochemical performance and microstructure of the alloys were investigated in detail. XRD results showed that the alloys had multiphase structure composed of （La, Mg）2Ni7, LaNi5 and small amount of LaNi2 phases. The discharge capacity of the alloys first increased and then decreased with increasing Co content. At a discharge current density of 900 mA/g, the HRD of the alloy electrodes increased from 81.3% （x=0） to 89.2 % （x=0.2）, and then reduced to 87.8 % （x=0.6）. After 60 charge/discharge cycles, the capacity retention rate of the alloys enhanced from 52.67% to 61.32%, and the capacity decay rate of the alloys decreased from 2.60 to 2.05 mAh/g per cycle with increasing Co content. The obtained results by XPS and XRD showed that the fundamental reasons for the capacity decay of the La-Mg-Ni system （Ce2Ni7-type） alloy electrodes were corrosion and oxidation as well as passivation of Mg and Lain alkaline solution.
文摘Investigation of alloy structure shows that La2-xMgxNi7 （x = 0.3 - 0.8） alloys are mainly com- posed of Ce/Ni7-type, Gd2Co7-type and PuNi3-type phase. The influence of Mg content in alloys on the phase structure is great, resulting in a linear decrease of the unit cell parameters of main phases and increase of hydrogen absorption/desorption plateau as Mg content increases. Electrochemical measurements show that as the Mg content increases, the discharge capacity of alloy electrodes first increases and then decreases. The cyclic stability presents a deteriorative trend. La1.4Mg0.6 Ni7 alloy electrode exhibits the maximum electrochemical discharge capacity （378 mAh·g^-1）, and the La1.6Mg0.4Ni7 alloy electrode shows the best cyclic stability （S270 = 81%）.
基金the National Natural Science Funding (50201001)Beijing Natural Science Foundation (2041001)National High Technology Research and Development Program of China (2007AA03Z458)
文摘Bulk nanocrystalline SmCo6Fe sintered magnet was prepared by Spark Plasma Sintering technique (SPS). XRD patterns show that the magnet exhibits a stable TbCu7 structure. TEM observation indicates that the microstructure of the magnet is composed of SmCo6Fe single phase grains with an average grain size of 30 nm. Magnetic measurement shows that under 9 T magnetic field, the coercivity of the magnet reaches 1.12 T; the saturation magnetization and the remanence are 1.13 and 0.67 T, respectively. The magnet has a (BH)max of 75.6 kJ·cm-3.
文摘The partial substitution of Zr for La has been performed in order to ameliorate the electrochemical hydrogen storage performances of La–Mg–Ni based A2B7-type electrode alloys. The melt spinning technology was used to prepare the La0.75-xZrxMg0.25Ni3.2Co0.2Al0.1 (x=0, 0.05, 0.1, 0.15, 0.2) electrode alloys. The impacts of the melt spinning and the substituting La with Zr on the structures and the electrochemical hydrogen storage characteristics of the alloys were systemically investigated. The analysis of XRD and TEM reveals that the as-cast and spun alloys have a multiphase structure, composing of two main phases (La, Mg)2Ni7 and LaNi5 as well as a residual phase LaNi2. The electrochemical measurement indicates that both the substitution of Zr for La and the melt spinning ameliorate the electrochemical cycle stability of the alloys dramatically. Furthermore, the high rate discharge ability (HRD) of the as-spun (10 m/s) alloys notably declines with growing the amount of Zr substitution, while it first augments and then falls for the (x=0.1) alloy with rising the spinning rate.
基金Project supported by the National Natural Science Foundation of China(50642033 50701011)+1 种基金Key Technologies R&D Program of Inner Mongolia, China (20050205)Natural Science Foundation of Inner Mongolia, China (200711020703)
文摘To improve the cyclic stability of La-Mg-Ni system alloy, as-cast La0.75Mg0.25Ni3.5Co0.2 alloy was annealed at 1123, 1223, and 1323 K for 10 h in 0.3 MPa argon. The microstructure and electrochemical performance of different annealed alloys were investigated systematically by X-Ray Diffraction （XRD）, Scanning Electron Microscopy （SEM）, X-Ray Photoelectron Spectroscopy （XPS）, and electrochemical experiments. The results obtained by XRD and SEM showed that the as-cast and annealed （1123 K） alloys had multiphase structure containing LaNis, （La, Mg）2（Ni, Co）7 and few LaNi2 phases. When annealing temperatures approached 1223 and 1323 K, LaNi2 phase disappeared. The annealed alloys at 1223 and 1323 K were composed of LaNi5, （La, Mg）2（Ni, Co）7 and （La, Mg）（Ni, Co）3 phases. With increasing annealing temperature, the maximum discharge capacity of the alloy decreased monotonously, but the cyclic stability was improved owing to structure homogeneity and grain growth after annealing, as well as the enhancement of anti-oxidation/corrosion ability and the suppression of pulverization during cycling in KOH electrolyte.
基金supported by the National Natural Science Foundation of China(Nos.51161015 and 50961009)the National High-Technology Research and Development Program of China(No.2011AA03A408)the Natural Science Foundation of Inner Mongolia,China(Nos.2011ZD10 and 2010ZD05)
文摘In order to ameliorate the electrochemical hydrogen storage performances of La-Mg–Ni system A_2B_7-type electrode alloys, the partial substitution of M (M = Zr, Pr) for La was performed. The melt spinning technology was used to fabricate the La_(0.75-x)M_xMg_0.25Ni_3.2Co_0.2Al_0.1 (M = Zr, Pr; x = 0, 0.1) electrode alloys. The influences of the melt spinning and substituting La with M (M = Zr, Pr) on the structures and the electrochemical hydrogen storage characteristics of the alloys were investigated. The analysis of XRD, SEM, and TEM reveals that the as-cast and spun alloys have a multiphase structure composed of two main phases (La, Mg)_2Ni_7 and LaNi_5 as well as a residual phase LaNi_2 . The as-spun (M = Pr) alloy displays an entire nanocrystalline structure, while an amorphous-like structure is detected in the as-spun (M = Zr) alloy, implying that the substitution of Zr for La facilitates the amorphous formation. The electrochemical measurements exhibit that the substitution of Pr for La clearly increases the discharge capacity of the alloys; however, the Zr substitution brings on an adverse impact. Meanwhile, the M (M = Zr, Pr) substitution significantly enhances its cycle stability. The melt spinning exerts an evident effect on the electrochemical performances of the alloys, whose discharge capacity and high rate discharge ability (HRD) first mount up and then fall with the growing spinning rate, whereas their cycle stabilities monotonously augment as the spinning rate increases.
基金Project(2007AA03Z227)supported by High-tech Research and Development Program of ChinaProjects(50871050,50701011)supported by the National Natural Science Foundation of China+1 种基金Project(200711020703)supported by the Natural Science Foundation of Inner Mongolia,ChinaProject(NJzy08071)supported by High Education Science Research Project of Inner Mongolia,China
文摘The La-Mg-Ni system A2B7-type electrode alloys with nominal composition La0.75-xZrxMg0.25Ni3.2Co0.2Al0.1(x=0,0.05, 0.1,0.15,0.2)were prepared by casting and melt-spinning.The influences of melt spinning on the electrochemical performances as well as the structures of the alloys were investigated.The results obtained by XRD,SEM and TEM show that the as-cast and spun alloys have a multiphase structure,consisting of two main phases(La,Mg)Ni3 and LaNi5 as well as a residual phase LaNi2.The melt spinning leads to an obvious increase of the LaNi5 phase and a decrease of the(La,Mg)Ni3 phase in the alloys.The results of the electrochemical measurement indicate that the discharge capacity of the alloys(x≤0.1)first increases and then decreases with the increase of spinning rate,whereas for x>0.1,the discharge capacity of the alloys monotonously falls.The melt spinning slightly impairs the activation capability of the alloys,but it significantly enhances the cycle stability of the alloys.
