This paper presents findings of a study on solid wastes conversion into fuels through pyrolysis of plastic materials, presenting an alternative renewable approach for waste management. Investigations were conducted on...This paper presents findings of a study on solid wastes conversion into fuels through pyrolysis of plastic materials, presenting an alternative renewable approach for waste management. Investigations were conducted on conversion of polypropylene (PP), low-density polyethylene (LDPE) and high-density polyethylene (HDPE) under normal and catalyst mediated process conditions. Plastic wastes were collected from various dumpsites in Nairobi and segregated using plastic resin codes to various classes. Samples were cleaned, dried and shredded to 2 mm and fed into a pyrolysis reactor. The pyrolysis process was conducted at between 220˚C and 420˚C. Pyrolysis gases were condensed in a shell and coil condenser and the incondensable gases were stored in gasbags. Liquid fuels were analysed using Gas chromatograph with a mass spectroscopic detector and Fourier Transform Infrared Spectrometry. The results revealed that the most optimal process conditions were a temperature range of 220˚C - 420˚C at a heating rate of 10˚C per minute. Under these conditions, the oil yields were 53.72% for PP, 62.10% for LDPE, and 64.14% for HDPE. As the heating rate increased from 10˚C/min to 20˚C/min, gas yields increased, rising from 28.05% to 31.12% in PP, 14.96% to 30.62% in LDPE, and 18.51% to 29.49% in HDPE. The introduction of Fe2O3 and Al2O3 catalyst significantly enhanced gas production during pyrolysis, increasing yields from 18% to 61% and 47% respectively.展开更多
The ability to unlock the interplay between the activity and stability of oxygen reduction reaction(ORR)represents an important endeavor toward creating robust ORR catalysts for efficient fuel cells.Herein,we report a...The ability to unlock the interplay between the activity and stability of oxygen reduction reaction(ORR)represents an important endeavor toward creating robust ORR catalysts for efficient fuel cells.Herein,we report an effective strategy to concurrent enhance the activity and stability of ORR catalysts via constructing atomically dispersed Fe-Mn dualmetal sites on N-doped carbon(denoted(FeMn-DA)-N-C)for both anion-exchange membrane fuel cells(AEMFC)and proton exchange membrane fuel cells(PEMFC).The(FeMn-DA)-N-C catalysts possess ample dual-metal atoms consisting of adjacent Fe-N_(4)and Mn-N_(4)sites on the carbon surface,yielded via a facile doping-adsorption-pyrolysis route.The introduction of Mn carries several advantageous attributes:increasing the number of active sites,effectively anchoring Fe due to effective electron transfer to Mn(revealed by X-ray absorption spectroscopy and density-functional theory(DFT),thus preventing the aggregation of Fe),and effectively circumventing the occurrence of Fenton reaction,thus reducing the consumption of Fe.The(FeMn-DA)-N-C catalysts showcase half-wave potentials of 0.92 and 0.82 V in 0.1 M KOH and 0.1 M HClO_(4),respectively,as well as outstanding stability.As manifested by DFT calculations,the introduction of Mn affects the electronic structure of Fe,down-shifts the d-band Fe active center,accelerates the desorption of OH groups,and creates higher limiting potentials.The AEMFC and PEMFC with(FeMn-DA)-N-C as the cathode catalyst display high power densities of 1060 and 746 mW cm^(-2),respectively,underscoring their promising potential for practical applications.Our study highlights the robustness of designing Fe-containing dual-atom ORR catalysts to promote both activity and stability for energy conversion and storage materials and devices.展开更多
Proton exchange membrane fuel cells (PEMFCs) provide an appealing sustainable energy system,with the solid-electrolyte membrane playing a crucial role in its overall performance.Currently,sulfonated poly(1,4-phenylene...Proton exchange membrane fuel cells (PEMFCs) provide an appealing sustainable energy system,with the solid-electrolyte membrane playing a crucial role in its overall performance.Currently,sulfonated poly(1,4-phenylene ether-ether sulfone)(SPEES),an aromatic hydrocarbon polymer,has garnered considerable attention as an alternative to Nafion polymers.However,the long-term durability and stability of SPEES present a significant challenge.In this context,we introduce a potential solution in the form of an additive,specifically a core–shell-based amine-functionalized iron titanate (A–Fe_(2)TiO_(5)),which holds promise for improving the lifetime,proton conductivity,and power density of SPEES in PEMFCs.The modified SPEES/A–Fe_(2)TiO_(5)composite membranes exhibited notable characteristics,including high water uptake,enhanced thermomechanical stability,and oxidative stability.Notably,the SPEES membrane loaded with 1.2 wt%of A–Fe_(2)TiO_(5)demonstrates a maximum proton conductivity of 155 mS ccm^(-1),a twofold increase compared to the SPEES membrane,at 80°C under 100%relative humidity (RH).Furthermore,the 1.2 wt%of A–Fe_(2)TiO_(5)/SPEES composite membranes exhibited a maximum power density of 397.37 mW cm^(-2)and a current density of 1148 mA cm^(-2)at 60°C under 100%RH,with an opencircuit voltage decay of 0.05 m V/h during 103 h of continuous operation.This study offers significant insights into the development and understanding of innovative SPEES nanocomposite membranes for PEMFC applications.展开更多
Hydrogen energy is a renewable and clean resource,that can promote the transformation of energy use terminals to green and low carbon,alleviate the current problems of energy shortage,respond to China’s“double carbo...Hydrogen energy is a renewable and clean resource,that can promote the transformation of energy use terminals to green and low carbon,alleviate the current problems of energy shortage,respond to China’s“double carbon”strategy,and further implement the energy-saving and emission reduction targets.The hydrogen fuel cell is an efficient and environmentally friendly distributed power generation device,with the advantages of high energy density,zero-emission,fast charging speed,etc.,and has been widely used in the fields of new energy vehicles,electric power equipment,and portable equipment.This paper analyzes the principle and advantages of hydrogen fuel cells,analyzes the key technology system of hydrogen fuel cells and the application of artificial intelligence in hydrogen fuel cells,proposes to strengthen the research on hydrogen production technology,accelerates the technical research and transformation application of key materials and core components,formulate industrial planning scientifically and actively promote hydrogen fuel cell,and promote the transformation of scientific and technological achievements,to promote the development of the hydrogen fuel cell industry.展开更多
Crude petroleum pollution causes some serious ecological disasters in the ocean.Marine sediment microbial fuel cells(MSMFCs)have been utilized as a novel method for in-situ degradation and a long-term power source.Her...Crude petroleum pollution causes some serious ecological disasters in the ocean.Marine sediment microbial fuel cells(MSMFCs)have been utilized as a novel method for in-situ degradation and a long-term power source.Herein,the effect of different concentrations of rhamnolipids biosurfactant on the electrochemical performance of MSMFCs anode and the higher efficiency of oil degradation are creatively investigated.The results indicate that the anode in sediment containing rhamnolipids effectively enriches the indigenous electrogenic Pseudophaeobacter and Pseudomonas,which significantly enhances the electrochemical performance of the MSMFCs.Under rhamnolipids at the concentration of 200 mg kg^(-1)in sediment,the anode specific capacitance(401.45 Fm^(-2)),exchange current density(4.87×10^(-2)mAm^(-2)),and cell maximum power density(140.24 mWm^(-2))increase by 2.50,38.65,and 2.11 times,respectively,in comparison with its natural sediment.And the oil degradation rate(40.06%)was higher than the blank(17.55%).It demonstrates that the synergistic effect between electrochemical catalytic degradation and emulsifying solubilization of rhamnolipids surfactant directly accelerates the degradation of petroleum in marine sediment,which will provide a novel method and theoretical guidance for in-situ degradation and efficient removal of crude petroleum on ocean floor.展开更多
High-entropy materials have become high-activity electrocatalysis owing to their high-entropy effect and multiple active sites.Herein,we synthesize a series of carbon-supported nano high-entropy oxides(HEOs/C),specifi...High-entropy materials have become high-activity electrocatalysis owing to their high-entropy effect and multiple active sites.Herein,we synthesize a series of carbon-supported nano high-entropy oxides(HEOs/C),specifically (PtFeCoNiCu)O/C,using a carbothermal shock (CTS) method for application as a cathode catalyst in direct borohydride fuel cells (DBFCs).The microstructure of the prepared catalysts was characterized by X-ray photoelectron spectroscopy,X-ray absorption fine structure,and transmission electron microscopy.The prepared (PtFeCoNiCu)O/C,with particle sizes ranging from 2 to 4 nm,demonstrates 3.94 transferred electrons towards the oxygen reduction reaction in an alkaline environment,resulting in a minimal H_(2)O_(2)yield of 2.6%.Additionally,it exhibits a Tafel slope of 61 mV dec-1,surpassing that of commercial Pt/C (82 mV dec-1).Furthermore,after 40,000 cycles of cyclic voltammetry(CV) testing,the half-wave potential of (PtFeCoNiCu)O/C shows a positive shift of 3 mV,with no notable decline in the limiting current density.When (PtFeCoNiCu)O/C is used as a cathode catalyst in DBFCs,the DBFC achieves a maximum power density of 441 mW cm^(-2)at 60°C and sustains a cell voltage of approximately 0.73 V after 52 h at 30°C.These findings confirm that HEO/C is a promising cathode catalyst for DBFCs.展开更多
Solid oxide fuel cells(SOFCs)have attracted a great deal of interest because they have the highest efficiency without using any noble metal as catalysts among all the fuel cell technologies.However,traditional SOFCs s...Solid oxide fuel cells(SOFCs)have attracted a great deal of interest because they have the highest efficiency without using any noble metal as catalysts among all the fuel cell technologies.However,traditional SOFCs suffer from having a higher volume,current leakage,complex connections,and difficulty in gas sealing.To solve these problems,Rolls-Royce has fabricated a simple design by stacking cells in series on an insulating porous support,resulting in the tubular segmented-in-series solid oxide fuel cells(SIS-SOFCs),which achieved higher output voltage.This work systematically reviews recent advances in the structures,preparation methods,perform-ances,and stability of tubular SIS-SOFCs in experimental and numerical studies.Finally,the challenges and future development of tubular SIS-SOFCs are also discussed.The findings of this work can help guide the direction and inspire innovation of future development in this field.展开更多
Iron-nitrogen-carbon(Fe-N-C)catalysts for the oxygen reduction reaction(ORR)in proton exchange membrane fuel cells(PEMFCs)have seriously been hindered by their poor ORR performance of Fe-N-C due to the low active site...Iron-nitrogen-carbon(Fe-N-C)catalysts for the oxygen reduction reaction(ORR)in proton exchange membrane fuel cells(PEMFCs)have seriously been hindered by their poor ORR performance of Fe-N-C due to the low active site density(SD)and site utilization.Herein,we reported a melamine-assisted vapor deposition approach to overcome these hindrances.The melamine not only compensates for the loss of nitrogen caused by high-temperature pyrolysis but also effectively etches the carbon substrate,increasing the external surface area and mesoporous porosity of the carbon substrate.These can provide more useful area for subsequent vapor deposition on active sites.The prepared 0.20Mela-FeNC catalyst shows a fourfold higher SD value and site utilization than the FeNC without the treatment of melamine.As a result,0.20Mela-FeNC catalyst exhibits a high ORR activity with a half-wave potential(E_(1/2))of 0.861 V and 12-fold higher ORR mass activity than the FeNC in acidic media.As the cathode in a H_(2)-O_(2)PEMFCs,0.20Mela-FeNC catalyst demonstrates a high peak power density of 1.30 W cm^(-2),outstripping most of the reported Fe-N-C catalysts.The developed melamine-assisted vapor deposition approach for boosting the SD and utilization of Fe-N-C catalysts offers a new insight into high-performance ORR electrocatalysts.展开更多
This paper examines the nutrition impacts of using non-solid cooking fuel on under-five children in developing countries.We draw on data from more than 1.12 million children in 62 developing countries from the Demogra...This paper examines the nutrition impacts of using non-solid cooking fuel on under-five children in developing countries.We draw on data from more than 1.12 million children in 62 developing countries from the Demographic and Health Surveys(DHS).Results from both fixed effects(FE)and instrumental variable(IV)estimates show that using non-solid cooking fuel significantly improves the nutrition outcomes of under-five children.Compared with their peers from households mainly using solid fuel,children from households mainly using non-solid fuel exhibit a lower probability of experiencing stunting(by 5.9 percentage points)and being underweight(by 1.2 percentage points).Our further investigation provides evidence for several underlying mechanisms,such as improved indoor air quality,induced reduction in children’s respiratory symptoms,benefits on maternal health,and reduction in maternal time spent on fuel collection or cooking.Heterogenous analyses suggest that the nutrition benefits of using non-solid cooking fuel are more prominent among boys,children above three years old,and those from households of lower socioeconomic status,rural areas,and Southeast Asia.展开更多
For protonic ceramic fuel cells,it is key to develop material with high intrinsic activity for oxygen activation and bulk proton conductivity enabling water formation at entire electrode surface.However,a higher water...For protonic ceramic fuel cells,it is key to develop material with high intrinsic activity for oxygen activation and bulk proton conductivity enabling water formation at entire electrode surface.However,a higher water content which benefitting for the increasing proton conductivity will not only dilute the oxygen in the gas,but also suppress the O_(2)adsorption on the electrode surface.Herein,a new electrode design concept is proposed,that may overcome this dilemma.By introducing a second phase with high-hydrating capability into a conventional cobalt-free perovskite to form a unique nanocomposite electrode,high proton conductivity/concentration can be reached at low water content in atmosphere.In addition,the hydronation creates additional fast proton transport channel along the two-phase interface.As a result,high protonic conductivity is reached,leading to a new breakthrough in performance for proton ceramic fuel cells and electrolysis cells devices among available air electrodes.展开更多
This work focuses on the development of high temperature polymer electrolyte membranes(HT-PEMs)as key materials for HT-PEM fuel cells(HT-PEMFCs).Recognizing the challenges associated with the phosphoric acid(PA) doped...This work focuses on the development of high temperature polymer electrolyte membranes(HT-PEMs)as key materials for HT-PEM fuel cells(HT-PEMFCs).Recognizing the challenges associated with the phosphoric acid(PA) doped polybenzimidazole(PBI) membranes,including the use of carcinogenic monomers and complex synthesis procedures,this study aims to develop more cost-effective,readily synthesized,and high-performance alternatives.A series of superacid-catalyzed polyhydroxyalkylation reactions have been carefully designed between p-terphenyl and aldehydes bearing imidazole moieties,resulting in a new class of HT-PEMs.It is found that the chemical structure of aldehyde-substituted N-heterocycles significantly impacts the polymerization reaction.Specifically,the use of 1-methyl-2-imidazole-formaldehyde and 1 H-imidazole-4-formaldehyde monomers leads to the formation of high-viscosity,rigid,and ether-free polymers,denoted as PTIm-a and PTIm-b.Membranes fabricated from these polymers,due to their pendent imidazole groups,exhibit an exceptional capacity for PA absorption.Notably,PTIm-a,carrying methylimidazole moieties,demonstrates a superior chemical stability by maintaining morphology and structural stability during 350 h of Fenton testing.After being immersed in 75 wt% PA at 40℃,the PTIm-a membrane reaches a PA content of 152%,maintains a good tensile strength of 13.6 MPa,and exhibits a moderate conductivity of 50.2 mS cm^(-1) at 180℃.Under H_(2)/O_(2) operational conditions,a single cell based on the PTIm-a membrane attains a peak power density of 732 mW cm^(-2) at 180℃ without backpressure.Furthermore,the membrane demonstrates stable cycle stability over 173 h within 18 days at a current density of 200 mA cm^(-2),indicating its potential for practical application in HT-PEMFCs.This work highlights innovative strategies for the synthesis of advanced HT-PEMs,offering significant improvements in membrane properties and fuel cell performance,thus expanding the horizons of HT-PEMFC technology.展开更多
The reduced sealing difficulty of tubular solid oxide fuel cells(SOFCs)makes the stacking of tubular cell groups relatively easy,and the thermal stress constraints during stack operation are smaller,which helps the st...The reduced sealing difficulty of tubular solid oxide fuel cells(SOFCs)makes the stacking of tubular cell groups relatively easy,and the thermal stress constraints during stack operation are smaller,which helps the stack to operate stably for a long time.The special design of tubular SOFC structures can completely solve the problem of high-temperature sealing,especially in the design of multiple single-cell series integrated into one tube,where each cell tube is equivalent to a small electric stack,with unique characteristics of high voltage and low current output,which can significantly reduce the ohmic polarization loss of tubular cells.This paper provides an overview of typical tubular SOFC structural designs both domestically and internationally.Based on the geometric structure of tubular SOFCs,they can be divided into bamboo tubes,bamboo flat tubes,single-section tubes,and single-section flat tube structures.Meanwhile,this article provides an overview of commonly used materials and preparation methods for tubular SOFCs,including commonly used materials and preparation methods for support and functional layers,as well as a comparison of commonly used preparation methods for microtubule SOFCs,It introduced the three most important parts of building a fuel cell stack:manifold,current collector,and ceramic adhesive,and also provided a detailed introduction to the power generation systems of different tubular SOFCs,Finally,the development prospects of tubular SOFCs were discussed.展开更多
Joint time–frequency analysis is an emerging method for interpreting the underlying physics in fuel cells,batteries,and supercapacitors.To increase the reliability of time–frequency analysis,a theoretical correlatio...Joint time–frequency analysis is an emerging method for interpreting the underlying physics in fuel cells,batteries,and supercapacitors.To increase the reliability of time–frequency analysis,a theoretical correlation between frequency-domain stationary analysis and time-domain transient analysis is urgently required.The present work formularizes a thorough model reduction of fractional impedance spectra for electrochemical energy devices involving not only the model reduction from fractional-order models to integer-order models and from high-to low-order RC circuits but also insight into the evolution of the characteristic time constants during the whole reduction process.The following work has been carried out:(i)the model-reduction theory is addressed for typical Warburg elements and RC circuits based on the continued fraction expansion theory and the response error minimization technique,respectively;(ii)the order effect on the model reduction of typical Warburg elements is quantitatively evaluated by time–frequency analysis;(iii)the results of time–frequency analysis are confirmed to be useful to determine the reduction order in terms of the kinetic information needed to be captured;and(iv)the results of time–frequency analysis are validated for the model reduction of fractional impedance spectra for lithium-ion batteries,supercapacitors,and solid oxide fuel cells.In turn,the numerical validation has demonstrated the powerful function of the joint time–frequency analysis.The thorough model reduction of fractional impedance spectra addressed in the present work not only clarifies the relationship between time-domain transient analysis and frequency-domain stationary analysis but also enhances the reliability of the joint time–frequency analysis for electrochemical energy devices.展开更多
Developing efficient and stable cathodes for low-temperature solid oxide fuel cells(LT-SOFCs) is of great importance for the practical commercialization.Herein,we propose a series of Sm-modified Bi_(0.7-x)Sm_xSr_(0.3)...Developing efficient and stable cathodes for low-temperature solid oxide fuel cells(LT-SOFCs) is of great importance for the practical commercialization.Herein,we propose a series of Sm-modified Bi_(0.7-x)Sm_xSr_(0.3)FeO_(3-δ) perovskites as highly-active catalysts for LT-SOFCs.Sm doping can significantly enhance the electrocata lytic activity and chemical stability of cathode.At 600℃,Bi_(0.675)Sm_(0.025)Sr_(0.3)FeO_(3-δ)(BSSF25) cathode has been found to be the optimum composition with a polarization resistance of 0.098 Ω cm^2,which is only around 22.8% of Bi_(0.7)Sr_(0.3)FeO_(3-δ)(BSF).A full cell utilizing BSSF25 displays an exceptional output density of 790 mW cm^(-2),which can operate continuously over100 h without obvious degradation.The remarkable electrochemical performance observed can be attributed to the improved O_(2) transport kinetics,superior surface oxygen adsorption capacity,as well as O_(2)p band centers in close proximity to the Fermi level.Moreover,larger average bonding energy(ABE) and the presence of highly acidic Bi,Sm,and Fe ions restrict the adsorption of CO_(2) on the cathode surface,resulting in excellent CO_(2) resistivity.This work provides valuable guidance for systematic design of efficient and durable catalysts for LT-SOFCs.展开更多
The long-range periodically ordered atomic structures in intermetallic nanoparticles(INPs)can significantly enhance both the electrocatalytic activity and electrochemical stability toward the oxygen reduction reaction...The long-range periodically ordered atomic structures in intermetallic nanoparticles(INPs)can significantly enhance both the electrocatalytic activity and electrochemical stability toward the oxygen reduction reaction(ORR)compared to the disordered atomic structures in ordinary solid-solution alloy NPs.Accordingly,through a facile and scalable synthetic method,a series of carbon-supported ultrafine Pt_3Co_(x)Mn_(1-x)ternary INPs are prepared in this work,which possess the"skin-like"ultrathin Pt shells,the ordered L1_(2) atomic structure,and the high-even dispersion on supports(L1_(2)-Pt_3Co_(x)Mn_(1-x)/~SPt INPs/C).Electrochemical results present that the composition-optimized L1_(2)-Pt_3Co_(0.7)Mn_(0.3)/~SPt INPs/C exhibits the highest electrocata lytic activity among the series,which are also much better than those of the pristine ultrafine Pt/C.Besides,it also has a greatly enhanced electrochemical stability.In addition,the effects of annealing temperature and time are further investigated.More importantly,such superior ORR electrocatalytic performance of L1_(2)-Pt_3Co_(0.7)Mn_(0.3)/~SPt INPs/C are also well demonstrated in practical fuel cells.Physicochemical characterization analyses further reveal the major origins of the greatly enhanced ORR electrocata lytic performance:the Pt-Co-Mn alloy-induced geometric and ligand effects as well as the extremely high L1_(2) atomic-ordering degree.This work not only successfully develops a highly active and stable ordered ternary intermetallic ORR electrocatalyst,but also elucidates the corresponding"structure-function"relationship,which can be further applied in designing other intermetallic(electro)catalysts.展开更多
Nanoparticles anchored on the perovskite surface have gained considerable attention for their wide-ranging applications in heterogeneous catalysis and energy conversion due to their robust and integrated structural co...Nanoparticles anchored on the perovskite surface have gained considerable attention for their wide-ranging applications in heterogeneous catalysis and energy conversion due to their robust and integrated structural configuration.Herein,we employ controlled Co doping to effectively enhance the nanoparticle exsolution process in layered perovskite ferrites materials.CoFe alloy nanoparticles with ultra-high-density are exsolved on the(PrBa)_(0.95)(Fe_(0.8)Co_(0.1)Nb_(0.1))2O_(5+δ)(PBFCN_(0.1))surface under reducing atmosphere,providing significant amounts of reaction sites and good durability for hydrocarbon catalysis.Under a reducing atmosphere,cobalt facilitates the reduction of iron cations within PBFCN_(0.1),leading to the formation of CoFe alloy nanoparticles.This formation is accompanied by a cation exchange process,wherein,with the increase in temperature,partial cobalt ions are substituted by iron.Meanwhile,Co doping significantly enhance the electrical conductivity due to the stronger covalency of the Cosingle bondO bond compared with Fesingle bondO bond.A single cell with the configuration of PBFCN_(0.1)-Sm_(0.2)Ce_(0.8)O_(1.9)(SDC)|SDC|Ba_(0.5)Sr_(0.5)Co_(0.8)Fe_(0.2)O_(3−δ)(BSCF)-SDC achieves an extremely low polarization resistance of 0.0163Ωcm^(2)and a high peak power density of 740 mW cm^(−2)at 800℃.The cell also shows stable operation for 120 h in H_(2)with a constant current density of 285 mA cm^(−2).Furthermore,employing wet C_(2)H_(6)as fuel,the cell demonstrates remarkable performance,achieving peak power densities of 455 mW cm^(−2)at 800℃and 320 mW cm^(−2)at 750℃,marking improvements of 36%and 70%over the cell with(PrBa)_(0.95)(Fe_(0.9)Nb_(0.1))_(2)O_(5+δ)(PBFN)-SDC at these respective temperatures.This discovery emphasizes how temperature influences alloy nanoparticles exsolution within doped layered perovskite ferrites materials,paving the way for the development of high-performance ceramic fuel cell anodes.展开更多
The study of non-axisymmetric fuel dispersal and detonation can provide reference for the prevention of industrial cloud explosion accidents and the design of fuel air explosive(FAE).The concentration and detonation f...The study of non-axisymmetric fuel dispersal and detonation can provide reference for the prevention of industrial cloud explosion accidents and the design of fuel air explosive(FAE).The concentration and detonation fields of 85 kg cylindrical and fan-shaped fuel are investigated by experiments and numerical simulations.A dynamic model of the whole process for fuel dispersal and detonation is built.The concentration distribution of fuel is used as the initial condition to calculate the detonation stage,thus solving the initial value problem of detonation field.The phase and component changes of fuel cloud at different locations are compared.The fuel cloud is divided into directions of 0°,90°,135°and 180°.The results show that the maximum cloud radius is 20.94 m in 135°and the minimum is 12.04 m in 0°.The diameter of the detonation fireball is 53.6 m,and the peak temperature is 3455 K.The highest peak overpressure is 3.44 MPa in 0°and the lowest is 2.97 MPa in 135°.The proportion of liquid phase in 0°is22.90%,and the fuel loss is 11.8% and 9% higher than that in 135°and cylindrical charge,respectively.The stable propagation distance of blast wave in 135°is 42.50% longer than 0°and 28.37% longer than cylindrical charge.展开更多
Energetic nanofluid fuel has caught the attention of the field of aerospace liquid propellant for its high energy density(HED), but it suffers from the inevitable solid-liquid phase separation problem. To resolve this...Energetic nanofluid fuel has caught the attention of the field of aerospace liquid propellant for its high energy density(HED), but it suffers from the inevitable solid-liquid phase separation problem. To resolve this problem, herein we synthesized the high-Al-/B-containing(up to 30%(mass)) HED gelled fuels, with low-molecular-mass organic gellant Z, which show high net heat of combustion(NHOC), density, storage stability, and thixotropic properties. The characterizations indicate that the application of energetic particles to the gelled fuels obviously destroys their fibrous network structures but can provide the new particle-gellant gelation microstructures, resulting in the comparable stability between 1.0%(mass) Z/JP-10 + 30%(mass) Al or B and pure JP-10 gelled fuel. Moreover, the gelled fuels with high-content Al or B exhibit high shear-thinning property, recovery capability, and mechanical strength, which are favorable for their storage and utilization. Importantly, the prepared 1.0%(mass) Z/JP-10 + 30%(mass) B(or 1.0%(mass) Z/JP-10 + 30%(mass) Al) shows the density and NHOC 1.27 times(1.30) and 1.43 times(1.21)higher than pure JP-10, respectively. This work provides a facile and valid approach to the manufacturing of HED gelled fuels with high content of energetic particles for gel propellants.展开更多
Developing high ionic conducting electrolytes is crucial for applying proton-conducting fuel cell(PCFCs)practically.The cur-rent study investigates the effect of alumina on the structural,morphological,electrical,and ...Developing high ionic conducting electrolytes is crucial for applying proton-conducting fuel cell(PCFCs)practically.The cur-rent study investigates the effect of alumina on the structural,morphological,electrical,and electrochemical properties of CeO_(2).Lattice oxygen vacancies are induced in CeO_(2) by a general doping concept that enables fast ionic conduction at low-temperature ranges(300-500℃)for PCFCs.Rietveld refinement of the X-ray diffraction(XRD)patterns established the pure cubic fluorite structure of Al-doped CeO_(2)(ADC)samples and confirmed Al ions’fruitful integration in the CeO_(2) lattice.The electronic structure of the alumina-doped ceria of the materials(10ADC,20ADC,and 30ADC)has been investigated.As a result,it was found that the best composition of 30ADC-based electrolytes induced maximum lattice oxygen vacancies.The corresponding PCFC exhibited a maximum power output of 923 mW/cm^(2)at 500℃.Moreover,the investigation proves the proton-conducting ability of alumina-doped ceria-based fuel cells by using an oxide ion-blocking layer.展开更多
Following publication of the original article,the authors observed that both Fig.5 and Fig.4 depict the same image.Figure 5 was inaccurately referenced and displayed.The correct Fig.5 is copied below:The original arti...Following publication of the original article,the authors observed that both Fig.5 and Fig.4 depict the same image.Figure 5 was inaccurately referenced and displayed.The correct Fig.5 is copied below:The original article has been updated.展开更多
文摘This paper presents findings of a study on solid wastes conversion into fuels through pyrolysis of plastic materials, presenting an alternative renewable approach for waste management. Investigations were conducted on conversion of polypropylene (PP), low-density polyethylene (LDPE) and high-density polyethylene (HDPE) under normal and catalyst mediated process conditions. Plastic wastes were collected from various dumpsites in Nairobi and segregated using plastic resin codes to various classes. Samples were cleaned, dried and shredded to 2 mm and fed into a pyrolysis reactor. The pyrolysis process was conducted at between 220˚C and 420˚C. Pyrolysis gases were condensed in a shell and coil condenser and the incondensable gases were stored in gasbags. Liquid fuels were analysed using Gas chromatograph with a mass spectroscopic detector and Fourier Transform Infrared Spectrometry. The results revealed that the most optimal process conditions were a temperature range of 220˚C - 420˚C at a heating rate of 10˚C per minute. Under these conditions, the oil yields were 53.72% for PP, 62.10% for LDPE, and 64.14% for HDPE. As the heating rate increased from 10˚C/min to 20˚C/min, gas yields increased, rising from 28.05% to 31.12% in PP, 14.96% to 30.62% in LDPE, and 18.51% to 29.49% in HDPE. The introduction of Fe2O3 and Al2O3 catalyst significantly enhanced gas production during pyrolysis, increasing yields from 18% to 61% and 47% respectively.
基金supported by the National Key R&D Program of China (2021YFF0500504)National Natural Science Foundation of China (No. 51976169)the financial supports from the Fundamental Research Funds for the Central Universities。
文摘The ability to unlock the interplay between the activity and stability of oxygen reduction reaction(ORR)represents an important endeavor toward creating robust ORR catalysts for efficient fuel cells.Herein,we report an effective strategy to concurrent enhance the activity and stability of ORR catalysts via constructing atomically dispersed Fe-Mn dualmetal sites on N-doped carbon(denoted(FeMn-DA)-N-C)for both anion-exchange membrane fuel cells(AEMFC)and proton exchange membrane fuel cells(PEMFC).The(FeMn-DA)-N-C catalysts possess ample dual-metal atoms consisting of adjacent Fe-N_(4)and Mn-N_(4)sites on the carbon surface,yielded via a facile doping-adsorption-pyrolysis route.The introduction of Mn carries several advantageous attributes:increasing the number of active sites,effectively anchoring Fe due to effective electron transfer to Mn(revealed by X-ray absorption spectroscopy and density-functional theory(DFT),thus preventing the aggregation of Fe),and effectively circumventing the occurrence of Fenton reaction,thus reducing the consumption of Fe.The(FeMn-DA)-N-C catalysts showcase half-wave potentials of 0.92 and 0.82 V in 0.1 M KOH and 0.1 M HClO_(4),respectively,as well as outstanding stability.As manifested by DFT calculations,the introduction of Mn affects the electronic structure of Fe,down-shifts the d-band Fe active center,accelerates the desorption of OH groups,and creates higher limiting potentials.The AEMFC and PEMFC with(FeMn-DA)-N-C as the cathode catalyst display high power densities of 1060 and 746 mW cm^(-2),respectively,underscoring their promising potential for practical applications.Our study highlights the robustness of designing Fe-containing dual-atom ORR catalysts to promote both activity and stability for energy conversion and storage materials and devices.
基金BK21 FOUR Program by Jeonbuk National University Research Grantsupported by “Regional Innovation Strategy (RIS)” through the National Research Foundation of Korea (NRF) funded by the Ministry of Education (MOE)(2023RIS-008)H2KOREA funded by the Ministry of Education(2024 Hydrogen Industry-002, Innovative Human Resources Development Project for Hydrogen Industry)。
文摘Proton exchange membrane fuel cells (PEMFCs) provide an appealing sustainable energy system,with the solid-electrolyte membrane playing a crucial role in its overall performance.Currently,sulfonated poly(1,4-phenylene ether-ether sulfone)(SPEES),an aromatic hydrocarbon polymer,has garnered considerable attention as an alternative to Nafion polymers.However,the long-term durability and stability of SPEES present a significant challenge.In this context,we introduce a potential solution in the form of an additive,specifically a core–shell-based amine-functionalized iron titanate (A–Fe_(2)TiO_(5)),which holds promise for improving the lifetime,proton conductivity,and power density of SPEES in PEMFCs.The modified SPEES/A–Fe_(2)TiO_(5)composite membranes exhibited notable characteristics,including high water uptake,enhanced thermomechanical stability,and oxidative stability.Notably,the SPEES membrane loaded with 1.2 wt%of A–Fe_(2)TiO_(5)demonstrates a maximum proton conductivity of 155 mS ccm^(-1),a twofold increase compared to the SPEES membrane,at 80°C under 100%relative humidity (RH).Furthermore,the 1.2 wt%of A–Fe_(2)TiO_(5)/SPEES composite membranes exhibited a maximum power density of 397.37 mW cm^(-2)and a current density of 1148 mA cm^(-2)at 60°C under 100%RH,with an opencircuit voltage decay of 0.05 m V/h during 103 h of continuous operation.This study offers significant insights into the development and understanding of innovative SPEES nanocomposite membranes for PEMFC applications.
文摘Hydrogen energy is a renewable and clean resource,that can promote the transformation of energy use terminals to green and low carbon,alleviate the current problems of energy shortage,respond to China’s“double carbon”strategy,and further implement the energy-saving and emission reduction targets.The hydrogen fuel cell is an efficient and environmentally friendly distributed power generation device,with the advantages of high energy density,zero-emission,fast charging speed,etc.,and has been widely used in the fields of new energy vehicles,electric power equipment,and portable equipment.This paper analyzes the principle and advantages of hydrogen fuel cells,analyzes the key technology system of hydrogen fuel cells and the application of artificial intelligence in hydrogen fuel cells,proposes to strengthen the research on hydrogen production technology,accelerates the technical research and transformation application of key materials and core components,formulate industrial planning scientifically and actively promote hydrogen fuel cell,and promote the transformation of scientific and technological achievements,to promote the development of the hydrogen fuel cell industry.
基金financially supported by the National Natural Science Foundation of China(No.22075262)。
文摘Crude petroleum pollution causes some serious ecological disasters in the ocean.Marine sediment microbial fuel cells(MSMFCs)have been utilized as a novel method for in-situ degradation and a long-term power source.Herein,the effect of different concentrations of rhamnolipids biosurfactant on the electrochemical performance of MSMFCs anode and the higher efficiency of oil degradation are creatively investigated.The results indicate that the anode in sediment containing rhamnolipids effectively enriches the indigenous electrogenic Pseudophaeobacter and Pseudomonas,which significantly enhances the electrochemical performance of the MSMFCs.Under rhamnolipids at the concentration of 200 mg kg^(-1)in sediment,the anode specific capacitance(401.45 Fm^(-2)),exchange current density(4.87×10^(-2)mAm^(-2)),and cell maximum power density(140.24 mWm^(-2))increase by 2.50,38.65,and 2.11 times,respectively,in comparison with its natural sediment.And the oil degradation rate(40.06%)was higher than the blank(17.55%).It demonstrates that the synergistic effect between electrochemical catalytic degradation and emulsifying solubilization of rhamnolipids surfactant directly accelerates the degradation of petroleum in marine sediment,which will provide a novel method and theoretical guidance for in-situ degradation and efficient removal of crude petroleum on ocean floor.
基金Zhejiang Provincial Natural Science Foundation of China (LZ22B060001,LY22E010003)“Pioneer” R&D Program of Zhejiang Province(2023C01080)National Natural Science Foundation of China (52301235)。
文摘High-entropy materials have become high-activity electrocatalysis owing to their high-entropy effect and multiple active sites.Herein,we synthesize a series of carbon-supported nano high-entropy oxides(HEOs/C),specifically (PtFeCoNiCu)O/C,using a carbothermal shock (CTS) method for application as a cathode catalyst in direct borohydride fuel cells (DBFCs).The microstructure of the prepared catalysts was characterized by X-ray photoelectron spectroscopy,X-ray absorption fine structure,and transmission electron microscopy.The prepared (PtFeCoNiCu)O/C,with particle sizes ranging from 2 to 4 nm,demonstrates 3.94 transferred electrons towards the oxygen reduction reaction in an alkaline environment,resulting in a minimal H_(2)O_(2)yield of 2.6%.Additionally,it exhibits a Tafel slope of 61 mV dec-1,surpassing that of commercial Pt/C (82 mV dec-1).Furthermore,after 40,000 cycles of cyclic voltammetry(CV) testing,the half-wave potential of (PtFeCoNiCu)O/C shows a positive shift of 3 mV,with no notable decline in the limiting current density.When (PtFeCoNiCu)O/C is used as a cathode catalyst in DBFCs,the DBFC achieves a maximum power density of 441 mW cm^(-2)at 60°C and sustains a cell voltage of approximately 0.73 V after 52 h at 30°C.These findings confirm that HEO/C is a promising cathode catalyst for DBFCs.
基金supported by the National Natural Science Foundation of China (Nos.21701083 and 22179054).
文摘Solid oxide fuel cells(SOFCs)have attracted a great deal of interest because they have the highest efficiency without using any noble metal as catalysts among all the fuel cell technologies.However,traditional SOFCs suffer from having a higher volume,current leakage,complex connections,and difficulty in gas sealing.To solve these problems,Rolls-Royce has fabricated a simple design by stacking cells in series on an insulating porous support,resulting in the tubular segmented-in-series solid oxide fuel cells(SIS-SOFCs),which achieved higher output voltage.This work systematically reviews recent advances in the structures,preparation methods,perform-ances,and stability of tubular SIS-SOFCs in experimental and numerical studies.Finally,the challenges and future development of tubular SIS-SOFCs are also discussed.The findings of this work can help guide the direction and inspire innovation of future development in this field.
基金granted by the National Natural Science Foundation of China(22172134,22288102)the National Key Research and Development Program of China(2017YFA0206500)
文摘Iron-nitrogen-carbon(Fe-N-C)catalysts for the oxygen reduction reaction(ORR)in proton exchange membrane fuel cells(PEMFCs)have seriously been hindered by their poor ORR performance of Fe-N-C due to the low active site density(SD)and site utilization.Herein,we reported a melamine-assisted vapor deposition approach to overcome these hindrances.The melamine not only compensates for the loss of nitrogen caused by high-temperature pyrolysis but also effectively etches the carbon substrate,increasing the external surface area and mesoporous porosity of the carbon substrate.These can provide more useful area for subsequent vapor deposition on active sites.The prepared 0.20Mela-FeNC catalyst shows a fourfold higher SD value and site utilization than the FeNC without the treatment of melamine.As a result,0.20Mela-FeNC catalyst exhibits a high ORR activity with a half-wave potential(E_(1/2))of 0.861 V and 12-fold higher ORR mass activity than the FeNC in acidic media.As the cathode in a H_(2)-O_(2)PEMFCs,0.20Mela-FeNC catalyst demonstrates a high peak power density of 1.30 W cm^(-2),outstripping most of the reported Fe-N-C catalysts.The developed melamine-assisted vapor deposition approach for boosting the SD and utilization of Fe-N-C catalysts offers a new insight into high-performance ORR electrocatalysts.
基金This work was supported by the National Natural Science Foundation of China(71861147003 and 71925009).
文摘This paper examines the nutrition impacts of using non-solid cooking fuel on under-five children in developing countries.We draw on data from more than 1.12 million children in 62 developing countries from the Demographic and Health Surveys(DHS).Results from both fixed effects(FE)and instrumental variable(IV)estimates show that using non-solid cooking fuel significantly improves the nutrition outcomes of under-five children.Compared with their peers from households mainly using solid fuel,children from households mainly using non-solid fuel exhibit a lower probability of experiencing stunting(by 5.9 percentage points)and being underweight(by 1.2 percentage points).Our further investigation provides evidence for several underlying mechanisms,such as improved indoor air quality,induced reduction in children’s respiratory symptoms,benefits on maternal health,and reduction in maternal time spent on fuel collection or cooking.Heterogenous analyses suggest that the nutrition benefits of using non-solid cooking fuel are more prominent among boys,children above three years old,and those from households of lower socioeconomic status,rural areas,and Southeast Asia.
基金supported from the National Key R&D Program of China(No.2022YFB4002502)National Natural Science Foundation of China under(No.22278203,22279057)+4 种基金the Jiangsu Funding Program for Excellent Postdoctoral Talentthe Priority Academic Program Development of Jiangsu Higher Education Institutions(PAPD)support from the Max Planck-POSTECH-Hsinchu Center for Complex Phase Materialssupport from the Fulbright Foundation Global Scholars Programthe U.S.Army Research Office under grant number W911NF-17-5401-0051
文摘For protonic ceramic fuel cells,it is key to develop material with high intrinsic activity for oxygen activation and bulk proton conductivity enabling water formation at entire electrode surface.However,a higher water content which benefitting for the increasing proton conductivity will not only dilute the oxygen in the gas,but also suppress the O_(2)adsorption on the electrode surface.Herein,a new electrode design concept is proposed,that may overcome this dilemma.By introducing a second phase with high-hydrating capability into a conventional cobalt-free perovskite to form a unique nanocomposite electrode,high proton conductivity/concentration can be reached at low water content in atmosphere.In addition,the hydronation creates additional fast proton transport channel along the two-phase interface.As a result,high protonic conductivity is reached,leading to a new breakthrough in performance for proton ceramic fuel cells and electrolysis cells devices among available air electrodes.
基金Natural Science Foundation of China (51603031)Liaoning Provincial Natural Science Foundation of China (2020-MS-087)China Scholarship Council(202306080157)。
文摘This work focuses on the development of high temperature polymer electrolyte membranes(HT-PEMs)as key materials for HT-PEM fuel cells(HT-PEMFCs).Recognizing the challenges associated with the phosphoric acid(PA) doped polybenzimidazole(PBI) membranes,including the use of carcinogenic monomers and complex synthesis procedures,this study aims to develop more cost-effective,readily synthesized,and high-performance alternatives.A series of superacid-catalyzed polyhydroxyalkylation reactions have been carefully designed between p-terphenyl and aldehydes bearing imidazole moieties,resulting in a new class of HT-PEMs.It is found that the chemical structure of aldehyde-substituted N-heterocycles significantly impacts the polymerization reaction.Specifically,the use of 1-methyl-2-imidazole-formaldehyde and 1 H-imidazole-4-formaldehyde monomers leads to the formation of high-viscosity,rigid,and ether-free polymers,denoted as PTIm-a and PTIm-b.Membranes fabricated from these polymers,due to their pendent imidazole groups,exhibit an exceptional capacity for PA absorption.Notably,PTIm-a,carrying methylimidazole moieties,demonstrates a superior chemical stability by maintaining morphology and structural stability during 350 h of Fenton testing.After being immersed in 75 wt% PA at 40℃,the PTIm-a membrane reaches a PA content of 152%,maintains a good tensile strength of 13.6 MPa,and exhibits a moderate conductivity of 50.2 mS cm^(-1) at 180℃.Under H_(2)/O_(2) operational conditions,a single cell based on the PTIm-a membrane attains a peak power density of 732 mW cm^(-2) at 180℃ without backpressure.Furthermore,the membrane demonstrates stable cycle stability over 173 h within 18 days at a current density of 200 mA cm^(-2),indicating its potential for practical application in HT-PEMFCs.This work highlights innovative strategies for the synthesis of advanced HT-PEMs,offering significant improvements in membrane properties and fuel cell performance,thus expanding the horizons of HT-PEMFC technology.
基金financially supported by the National Key Research and Development Program of China (No.2021YFB4001400)。
文摘The reduced sealing difficulty of tubular solid oxide fuel cells(SOFCs)makes the stacking of tubular cell groups relatively easy,and the thermal stress constraints during stack operation are smaller,which helps the stack to operate stably for a long time.The special design of tubular SOFC structures can completely solve the problem of high-temperature sealing,especially in the design of multiple single-cell series integrated into one tube,where each cell tube is equivalent to a small electric stack,with unique characteristics of high voltage and low current output,which can significantly reduce the ohmic polarization loss of tubular cells.This paper provides an overview of typical tubular SOFC structural designs both domestically and internationally.Based on the geometric structure of tubular SOFCs,they can be divided into bamboo tubes,bamboo flat tubes,single-section tubes,and single-section flat tube structures.Meanwhile,this article provides an overview of commonly used materials and preparation methods for tubular SOFCs,including commonly used materials and preparation methods for support and functional layers,as well as a comparison of commonly used preparation methods for microtubule SOFCs,It introduced the three most important parts of building a fuel cell stack:manifold,current collector,and ceramic adhesive,and also provided a detailed introduction to the power generation systems of different tubular SOFCs,Finally,the development prospects of tubular SOFCs were discussed.
基金support from the National Science Foundation of China(22078190)the National Key R&D Plan of China(2020YFB1505802).
文摘Joint time–frequency analysis is an emerging method for interpreting the underlying physics in fuel cells,batteries,and supercapacitors.To increase the reliability of time–frequency analysis,a theoretical correlation between frequency-domain stationary analysis and time-domain transient analysis is urgently required.The present work formularizes a thorough model reduction of fractional impedance spectra for electrochemical energy devices involving not only the model reduction from fractional-order models to integer-order models and from high-to low-order RC circuits but also insight into the evolution of the characteristic time constants during the whole reduction process.The following work has been carried out:(i)the model-reduction theory is addressed for typical Warburg elements and RC circuits based on the continued fraction expansion theory and the response error minimization technique,respectively;(ii)the order effect on the model reduction of typical Warburg elements is quantitatively evaluated by time–frequency analysis;(iii)the results of time–frequency analysis are confirmed to be useful to determine the reduction order in terms of the kinetic information needed to be captured;and(iv)the results of time–frequency analysis are validated for the model reduction of fractional impedance spectra for lithium-ion batteries,supercapacitors,and solid oxide fuel cells.In turn,the numerical validation has demonstrated the powerful function of the joint time–frequency analysis.The thorough model reduction of fractional impedance spectra addressed in the present work not only clarifies the relationship between time-domain transient analysis and frequency-domain stationary analysis but also enhances the reliability of the joint time–frequency analysis for electrochemical energy devices.
基金supported by the National Natural Science Foundation of China(22279025,21773048)the Natural Science Foundation of Heilongjiang Province(LH2021A013)+1 种基金the Sichuan Science and Technology Program(2021YFSY0022)the Fundamental Research Funds for the Central Universities(2023FRFK06005,HIT.NSRIF202204)。
文摘Developing efficient and stable cathodes for low-temperature solid oxide fuel cells(LT-SOFCs) is of great importance for the practical commercialization.Herein,we propose a series of Sm-modified Bi_(0.7-x)Sm_xSr_(0.3)FeO_(3-δ) perovskites as highly-active catalysts for LT-SOFCs.Sm doping can significantly enhance the electrocata lytic activity and chemical stability of cathode.At 600℃,Bi_(0.675)Sm_(0.025)Sr_(0.3)FeO_(3-δ)(BSSF25) cathode has been found to be the optimum composition with a polarization resistance of 0.098 Ω cm^2,which is only around 22.8% of Bi_(0.7)Sr_(0.3)FeO_(3-δ)(BSF).A full cell utilizing BSSF25 displays an exceptional output density of 790 mW cm^(-2),which can operate continuously over100 h without obvious degradation.The remarkable electrochemical performance observed can be attributed to the improved O_(2) transport kinetics,superior surface oxygen adsorption capacity,as well as O_(2)p band centers in close proximity to the Fermi level.Moreover,larger average bonding energy(ABE) and the presence of highly acidic Bi,Sm,and Fe ions restrict the adsorption of CO_(2) on the cathode surface,resulting in excellent CO_(2) resistivity.This work provides valuable guidance for systematic design of efficient and durable catalysts for LT-SOFCs.
基金supported by the National Key Research and Development Program of China(2021YFB4001301)the Science and Technology Commission of Shanghai Municipality(21DZ1208600)the Oceanic Interdisciplinary Program of Shanghai Jiao Tong University(SL2021ZD105)。
文摘The long-range periodically ordered atomic structures in intermetallic nanoparticles(INPs)can significantly enhance both the electrocatalytic activity and electrochemical stability toward the oxygen reduction reaction(ORR)compared to the disordered atomic structures in ordinary solid-solution alloy NPs.Accordingly,through a facile and scalable synthetic method,a series of carbon-supported ultrafine Pt_3Co_(x)Mn_(1-x)ternary INPs are prepared in this work,which possess the"skin-like"ultrathin Pt shells,the ordered L1_(2) atomic structure,and the high-even dispersion on supports(L1_(2)-Pt_3Co_(x)Mn_(1-x)/~SPt INPs/C).Electrochemical results present that the composition-optimized L1_(2)-Pt_3Co_(0.7)Mn_(0.3)/~SPt INPs/C exhibits the highest electrocata lytic activity among the series,which are also much better than those of the pristine ultrafine Pt/C.Besides,it also has a greatly enhanced electrochemical stability.In addition,the effects of annealing temperature and time are further investigated.More importantly,such superior ORR electrocatalytic performance of L1_(2)-Pt_3Co_(0.7)Mn_(0.3)/~SPt INPs/C are also well demonstrated in practical fuel cells.Physicochemical characterization analyses further reveal the major origins of the greatly enhanced ORR electrocata lytic performance:the Pt-Co-Mn alloy-induced geometric and ligand effects as well as the extremely high L1_(2) atomic-ordering degree.This work not only successfully develops a highly active and stable ordered ternary intermetallic ORR electrocatalyst,but also elucidates the corresponding"structure-function"relationship,which can be further applied in designing other intermetallic(electro)catalysts.
基金supported by National Natural Science Foundation of China Project (Grant No. 52374133, 52262034)the Guangdong Basic and Applied Basic Research Committee Foundation (Grant No. KCXST20221021111601003)Shenzhen Science and Technology Innovation Commission Foundation (Grant No. KCXST20221021111601003)
文摘Nanoparticles anchored on the perovskite surface have gained considerable attention for their wide-ranging applications in heterogeneous catalysis and energy conversion due to their robust and integrated structural configuration.Herein,we employ controlled Co doping to effectively enhance the nanoparticle exsolution process in layered perovskite ferrites materials.CoFe alloy nanoparticles with ultra-high-density are exsolved on the(PrBa)_(0.95)(Fe_(0.8)Co_(0.1)Nb_(0.1))2O_(5+δ)(PBFCN_(0.1))surface under reducing atmosphere,providing significant amounts of reaction sites and good durability for hydrocarbon catalysis.Under a reducing atmosphere,cobalt facilitates the reduction of iron cations within PBFCN_(0.1),leading to the formation of CoFe alloy nanoparticles.This formation is accompanied by a cation exchange process,wherein,with the increase in temperature,partial cobalt ions are substituted by iron.Meanwhile,Co doping significantly enhance the electrical conductivity due to the stronger covalency of the Cosingle bondO bond compared with Fesingle bondO bond.A single cell with the configuration of PBFCN_(0.1)-Sm_(0.2)Ce_(0.8)O_(1.9)(SDC)|SDC|Ba_(0.5)Sr_(0.5)Co_(0.8)Fe_(0.2)O_(3−δ)(BSCF)-SDC achieves an extremely low polarization resistance of 0.0163Ωcm^(2)and a high peak power density of 740 mW cm^(−2)at 800℃.The cell also shows stable operation for 120 h in H_(2)with a constant current density of 285 mA cm^(−2).Furthermore,employing wet C_(2)H_(6)as fuel,the cell demonstrates remarkable performance,achieving peak power densities of 455 mW cm^(−2)at 800℃and 320 mW cm^(−2)at 750℃,marking improvements of 36%and 70%over the cell with(PrBa)_(0.95)(Fe_(0.9)Nb_(0.1))_(2)O_(5+δ)(PBFN)-SDC at these respective temperatures.This discovery emphasizes how temperature influences alloy nanoparticles exsolution within doped layered perovskite ferrites materials,paving the way for the development of high-performance ceramic fuel cell anodes.
基金supported by the National Key Research and Development Program of China (Grant No.2021YFC3001204)。
文摘The study of non-axisymmetric fuel dispersal and detonation can provide reference for the prevention of industrial cloud explosion accidents and the design of fuel air explosive(FAE).The concentration and detonation fields of 85 kg cylindrical and fan-shaped fuel are investigated by experiments and numerical simulations.A dynamic model of the whole process for fuel dispersal and detonation is built.The concentration distribution of fuel is used as the initial condition to calculate the detonation stage,thus solving the initial value problem of detonation field.The phase and component changes of fuel cloud at different locations are compared.The fuel cloud is divided into directions of 0°,90°,135°and 180°.The results show that the maximum cloud radius is 20.94 m in 135°and the minimum is 12.04 m in 0°.The diameter of the detonation fireball is 53.6 m,and the peak temperature is 3455 K.The highest peak overpressure is 3.44 MPa in 0°and the lowest is 2.97 MPa in 135°.The proportion of liquid phase in 0°is22.90%,and the fuel loss is 11.8% and 9% higher than that in 135°and cylindrical charge,respectively.The stable propagation distance of blast wave in 135°is 42.50% longer than 0°and 28.37% longer than cylindrical charge.
基金support from the National Natural Science Foundation of China (22222808, 21978200)the Haihe Laboratory of Sustainable Chemical Transformations for financial support
文摘Energetic nanofluid fuel has caught the attention of the field of aerospace liquid propellant for its high energy density(HED), but it suffers from the inevitable solid-liquid phase separation problem. To resolve this problem, herein we synthesized the high-Al-/B-containing(up to 30%(mass)) HED gelled fuels, with low-molecular-mass organic gellant Z, which show high net heat of combustion(NHOC), density, storage stability, and thixotropic properties. The characterizations indicate that the application of energetic particles to the gelled fuels obviously destroys their fibrous network structures but can provide the new particle-gellant gelation microstructures, resulting in the comparable stability between 1.0%(mass) Z/JP-10 + 30%(mass) Al or B and pure JP-10 gelled fuel. Moreover, the gelled fuels with high-content Al or B exhibit high shear-thinning property, recovery capability, and mechanical strength, which are favorable for their storage and utilization. Importantly, the prepared 1.0%(mass) Z/JP-10 + 30%(mass) B(or 1.0%(mass) Z/JP-10 + 30%(mass) Al) shows the density and NHOC 1.27 times(1.30) and 1.43 times(1.21)higher than pure JP-10, respectively. This work provides a facile and valid approach to the manufacturing of HED gelled fuels with high content of energetic particles for gel propellants.
基金supported by the National Natural Science Foundation of China(Nos.51772080 and 11604088)the Funding from Science and Technology Department of Jiangsu Province,China(No.BE2022029)+1 种基金the Beijing Natural Science Foundation,China(No.IS23050)Prof.Asghar also thanks the Academy of Finland(Nos.13322738 and 13352669)for the financial support.
文摘Developing high ionic conducting electrolytes is crucial for applying proton-conducting fuel cell(PCFCs)practically.The cur-rent study investigates the effect of alumina on the structural,morphological,electrical,and electrochemical properties of CeO_(2).Lattice oxygen vacancies are induced in CeO_(2) by a general doping concept that enables fast ionic conduction at low-temperature ranges(300-500℃)for PCFCs.Rietveld refinement of the X-ray diffraction(XRD)patterns established the pure cubic fluorite structure of Al-doped CeO_(2)(ADC)samples and confirmed Al ions’fruitful integration in the CeO_(2) lattice.The electronic structure of the alumina-doped ceria of the materials(10ADC,20ADC,and 30ADC)has been investigated.As a result,it was found that the best composition of 30ADC-based electrolytes induced maximum lattice oxygen vacancies.The corresponding PCFC exhibited a maximum power output of 923 mW/cm^(2)at 500℃.Moreover,the investigation proves the proton-conducting ability of alumina-doped ceria-based fuel cells by using an oxide ion-blocking layer.
文摘Following publication of the original article,the authors observed that both Fig.5 and Fig.4 depict the same image.Figure 5 was inaccurately referenced and displayed.The correct Fig.5 is copied below:The original article has been updated.
