Coupled transfer of soil water and heat in closed columns of homogeneous red soil was studied under laboratory conditions. A coupled model was constructed using soil physical theory, empirical equations and experiment...Coupled transfer of soil water and heat in closed columns of homogeneous red soil was studied under laboratory conditions. A coupled model was constructed using soil physical theory, empirical equations and experimental data to predict the coupled transfer. The results show that transport of soil water was affected by temperature gradient, and the largest net water transport was found in the soil column with initial water content of 0.148 m3 m-3. At the same time, temperature changes with the transport of soil water was in a nonlinear shape as heat parameters were function of water content, and the changes of temperature were positively correlated with the net amount of water transported. Numerical modelling results show that the predicted values of temperature distribution were close to the observed values, while the predicted values of water content exhibited limited deviation at both ends of the soil column due to the slight temperature changes at both ends. It was indicated that the model proposed here was applicable.展开更多
A mathematical model of resin flow and temperature variation in the filling stage of the resin transfer molding (RTM) is developed based on the control volume/finite element method (CV/FEM). The effects of the heat tr...A mathematical model of resin flow and temperature variation in the filling stage of the resin transfer molding (RTM) is developed based on the control volume/finite element method (CV/FEM). The effects of the heat transfer and chemical reaction of the resin on the flow and temperature are considered. The numerical algorithm of the resin flow and temperature variation in the process of RTM are studied. Its accuracy and convergence are analyzed. The comparison of temperature variations between experimental results and model predictions is carried out for two RTM cases. Result shows that the model is efficient for evaluating the flow and temperature variation in the filling stage of RTM and there is a good coincidence between theory and experiment.展开更多
The objective of this study is to evaluate the difference of the soil water management in mango orchards between the varieties of “Irwin” in Japanand “Nam Dok Mai” inThailand. Field observations were conducted in ...The objective of this study is to evaluate the difference of the soil water management in mango orchards between the varieties of “Irwin” in Japanand “Nam Dok Mai” inThailand. Field observations were conducted in mango orchards in Okinawa, Japan and Phrao, Thailand to clarify the water management practices. Measurement of the hourly soil water content in Phrao indicated that the irrigation was scarce and the volumetric water content in the soil was maintained almost constant. in the flowering season. This can be the farmers’ practice for flower induction. After the flowering season, irrigation was frequent in order to produce the large fruit. In the harvest season, the soil water content was relatively high because of frequent irrigation and rainfall. In Okinawa, the volumetric water content was maintained at the same level in a relatively deep layer. The result at the5 cmdepth indicated that the farmer carefully controlled the soil water content. In the flowering season, the soil water content was relatively low. While the orchard was managed empirically, the volumetric water content near the soil surface was maintained over 25% during the harvest season. This result indicates that the farmer performed the good soil water management to enhance mango fruit quality even without technical measurement. A numerical model describing the soil water and heat transfers was introduced to predict the farmer’s empirical soil water management in Okinawa. Using the meteorological data in March 2010, the irrigation regime was predicted using the simulated soil water content. In the flowering season, the farmer irrigated when the soil surface water content reached 14%. Based on this criterion for the empirical soil water management, the simulation result indicated that the farmer irrigated four times in this period. The numerical model presented here can be useful for evaluating the differences in water management practices of local farmers.展开更多
This study is to understand the impact of operating conditions, especially initial operation temperature (T<sub>ini</sub>) which is set in a high temperature range, on the temperature profile of the interf...This study is to understand the impact of operating conditions, especially initial operation temperature (T<sub>ini</sub>) which is set in a high temperature range, on the temperature profile of the interface between the polymer electrolyte membrane (PEM) and the catalyst layer at the cathode (i.e., the reaction surface) in a single cell of polymer electrolyte fuel cell (PEFC). A 1D multi-plate heat transfer model based on the temperature data of the separator measured using the thermograph in a power generation experiment was developed to evaluate the reaction surface temperature (T<sub>react</sub>). In addition, to validate the proposed heat transfer model, T<sub>react</sub> obtained from the model was compared with that from the 3D numerical simulation using CFD software COMSOL Multiphysics which solves the continuity equation, Brinkman equation, Maxwell-Stefan equation, Butler-Volmer equation as well as heat transfer equation. As a result, the temperature gap between the results obtained by 1D heat transfer model and those obtained by 3D numerical simulation is below approximately 0.5 K. The simulation results show the change in the molar concentration of O<sub>2</sub> and H<sub>2</sub>O from the inlet to the outlet is more even with the increase in T<sub>ini</sub> due to the lower performance of O<sub>2</sub> reduction reaction. The change in the current density from the inlet to the outlet is more even with the increase in T<sub>ini</sub> and the value of current density is smaller with the increase in T<sub>ini </sub>due to the increase in ohmic over-potential and concentration over-potential. It is revealed that the change in T<sub>react</sub> from the inlet to the outlet is more even with the increase in T<sub>ini</sub> irrespective of heat transfer model. This is because the generated heat from the power generation is lower with the increase in T<sub>ini </sub>due to the lower performance of O<sub>2</sub> reduction reaction.展开更多
A modelling study is performed to compare the plasma flow and heat transfer characteristics of low-power arc-heated thrusters （arcjets） for three different propellants： hydrogen, nitrogen and argon. The all-speed S...A modelling study is performed to compare the plasma flow and heat transfer characteristics of low-power arc-heated thrusters （arcjets） for three different propellants： hydrogen, nitrogen and argon. The all-speed SIMPLE algorithm is employed to solve the governing equations, which take into account the effects of compressibility, Lorentz force and Joule heating, as well as the temperature- and pressure-dependence of the gas properties. The temperature, velocity and Mach number distributions calculated within the thruster nozzle obtained with different propellant gases are compared for the same thruster structure, dimensions, inlet-gas stagnant pressure and arc currents. The temperature distributions in the solid region of the anode-nozzle wall are also given. It is found that the flow and energy conversion processes in the thruster nozzle show many similar features for all three propellants. For example, the propellant is heated mainly in the near-cathode and constrictor region, with the highest plasma temperature appearing near the cathode tip; the flow transition from the subsonic to supersonic regime occurs within the constrictor region; the highest axial velocity appears inside the nozzle; and most of the input propellant flows towards the thruster exit through the cooler gas region near the anode-nozzle wall. However, since the properties of hydrogen, nitrogen and argon, especially their molecular weights, specific enthMpies and thermal conductivities, are different, there are appreciable differences in arcjet performance. For example, compared to the other two propellants, the hydrogen arcjet thruster shows a higher plasma temperature in the arc region, and higher axial velocity but lower temperature at the thruster exit. Correspondingly, the hydrogen arcjet thruster has the highest specific impulse and arc voltage for the same inlet stagnant pressure and arc current. The predictions of the modelling are compared favourably with available experimental results.展开更多
Our previous experimental studies have confirmed that viscoelastic-fluid-based nanofluid(VFBN) prepared by suspending nanoparticles in a viscoelastic base fluid(VBF, behaves drag reduction at turbulent flow state) can...Our previous experimental studies have confirmed that viscoelastic-fluid-based nanofluid(VFBN) prepared by suspending nanoparticles in a viscoelastic base fluid(VBF, behaves drag reduction at turbulent flow state) can reduce turbulent flow resistance as compared with water and enhance heat transfer as compared with VBF. Direct numerical simulation(DNS) is performed in this study to explore the mechanisms of heat transfer enhancement(HTE) and flow drag reduction(DR) for the VFBN turbulent flow. The Giesekus model is used as the constitutive equation for VFBN. Our previously proposed thermal dispersion model is adopted to take into account the thermal dispersion effects of nanoparticles in the VFBN turbulent flow. The DNS results show similar behaviors for flow resistance and heat transfer to those obtained in our previous experiments. Detailed analyses are conducted for the turbulent velocity, temperature, and conformation fields obtained by DNSs for different fluid cases, and for the friction factor with viscous, turbulent, and elastic contributions and heat transfer rate with conductive, turbulent and thermal dispersion contributions of nanoparticles, respectively. The mechanisms of HTE and DR of VFBN turbulent flows are then discussed. Based on analogy theory, the ratios of Chilton–Colburn factor to friction factor for different fluid flow cases are investigated, which from another aspect show the significant enhancement in heat transfer performance for some cases of water-based nanofluid and VFBN turbulent flows.展开更多
A modelling study is performed to investigate the characteristics of both plasma flow and heat transfer of a laminar non-transferred arc argon plasma torch operated at atmospheric and reduced pressure. It is found tha...A modelling study is performed to investigate the characteristics of both plasma flow and heat transfer of a laminar non-transferred arc argon plasma torch operated at atmospheric and reduced pressure. It is found that the calculated flow fields and temperature distributions are quite similar for both cases at a chamber pressure of 1.0 atm and 0.1 atm. A fully developed flow regime could be achieved in the arc constrictor-tube between the cathode and the anode of the plasma torch at 1.0 atm for all the flow rates covered in this study. However the flow field could not reach the fully developed regime at 0.1 atm with a higher flow rate. The arc-root is always attached to the torch anode surface near the upstream end of the anode, i.e. the abruptly expanded part of the torch channel, which is in consistence with experimental observation. The surrounding gas would be entrained from the torch exit into the torch interior due to a comparatively large inner diameter of the anode channel compared to that of the arc constrictor-tube.展开更多
In this paper, a numerical simulation has been carried out on unsteady hydromagnetic free convection near a moving infinite flat plate in a rotating medium. The temperatures involved are assumed to be very high so tha...In this paper, a numerical simulation has been carried out on unsteady hydromagnetic free convection near a moving infinite flat plate in a rotating medium. The temperatures involved are assumed to be very high so that the radiative heat transfer is significant, which renders the problem highly non-linear even with the assumption of a differential approximation for the radiative heat flux. A numerical method based on the Nakamura scheme has been employed to obtain the temperature and velocity distributions which are depicted graphically. The effects of the different parameters entering into the problem have been discussed extensively.展开更多
This paper illustrates the use of a general purpose differential equation （DE） solver called FlexPDE for the solution heat transfer problems in electric wire. FlexPDE uses the finite element method for the solution ...This paper illustrates the use of a general purpose differential equation （DE） solver called FlexPDE for the solution heat transfer problems in electric wire. FlexPDE uses the finite element method for the solution of boundary and initial value problems. A flexible input of the governing DE＇s and of material properties functions allows the simulation of non-linear variable behavior quickly and inexpensively. A modeling of temperature distribution in one-dimensional problem, a cross section of an electric wire was simulated. Comparison of those results obtained by FlexPDE with analytical and numerical solutions are done. The results compared well with those obtained from the analytical and numerical methods. The adaptability of the FlexPDE software for solving a variety of problem types was clearly demonstrated.展开更多
In this paper, a 3D model of a flat circuit board with a heat generating electronic chip mounted on it has been studied numerically. The conjugate heat transfer including the conduction in the chip and convection with...In this paper, a 3D model of a flat circuit board with a heat generating electronic chip mounted on it has been studied numerically. The conjugate heat transfer including the conduction in the chip and convection with the surrounding fluid has been investigated numerically. Computational fluid dynamics using the finite volume method has been used for modeling the conjugate heat transfer through the chip and the circuit board. Conjugate heat transfer has broad applications in engineering and industrial applications in design of cooling off electronic components. Effects of various inlet velocities have been studied on the heat transfer variation and temperature of the circuit board. Numerical results show that the temperature of the chip reduces as the velocity of the inlet fluid flow increases.展开更多
Theoretical and experimental studies show that during hail growth the heatand mass transfers play a determinant role in growth rates and different structures. However, manynumerical model researchers made extrapolatio...Theoretical and experimental studies show that during hail growth the heatand mass transfers play a determinant role in growth rates and different structures. However, manynumerical model researchers made extrapolation of the key heat transfer coefficient of the thermalbalance expression from measurements of evaporating water droplets obtained under small Renoldsnumbers (Re ≤ 200) introduced by Ranz and Marshall, leading to great difference from reality. Thispaper is devoted to the parameterization of measured heat transfer coefficients under Renoldsnumbers related to actual hail scales proposed by Zheng, which are then applied, to Hu-He 1D and 3Dmodels for hail growth respectively, indicating that the melting rate of a hailstone is 12%-50%bigger, the evaporation rate is 10%-200% higher and the dry-wet growth rate is 10%-40% larger fromthe present simulations than from the prototype models.展开更多
Currently, when magnesium alloy sheet is rolled, the method of controlling roll temperature is simple and inaccurate. Furthermore, roll temperature has a large influence on the quality of magnesium alloy sheet; theref...Currently, when magnesium alloy sheet is rolled, the method of controlling roll temperature is simple and inaccurate. Furthermore, roll temperature has a large influence on the quality of magnesium alloy sheet; therefore, a new model using circular fluid flow control roll temperature has been designed. A fluid heat transfer structure was designed, the heat transfer process model of the fluid heating roll was simplified, and the finite di erence method was used to cal?culate the heat transfer process. Fluent software was used to simulate the fluid?solid coupling heat transfer, and both the trend and regularity of the temperature field in the heat transfer process were identified. The results show that the heating e ciency was much higher than traditional heating methods(when the fluid heat of the roll and tempera?ture distribution of the roll surface was more uniform). Moreover, there was a bigger temperature di erence between the input and the output, and after using reverse flow the temperature di erence decreased. The axial and circum?ferential temperature distributions along the sheet were uniform. Both theoretical calculation results and numerical simulation results of the heat transfer between fluid and roll were compared. The error was 1.8%–12.3%, showing that the theoretical model can both forecast and regulate the temperature of the roll(for magnesium alloy sheets) in the rolling process.展开更多
Heat transfer of a capillary evaporator in a loop heat pipe was analyzed through 3D numerical simulations to study the effects of the thermal conductivity of the wick, the contact area between the casing and the wick,...Heat transfer of a capillary evaporator in a loop heat pipe was analyzed through 3D numerical simulations to study the effects of the thermal conductivity of the wick, the contact area between the casing and the wick, and the subcooling in the compensation chamber (CC) on the thermal performance of the evaporator. A pore network model with a distribution of pore radii was used to simulate liquid flow in the porous structure of the wick. To obtain high accuracy, fine meshes were used at the boundaries among the casing, the wick, and the grooves. Distributions of temperature, pressure, and mass flow rate were compared for polytetra-fluoroethylene (PTFE) and stainless steel wicks. The thermal conductivity of the wick and the contact area between the casing and the wick significantly impacted thermal performance of the evaporator heat-transfer coefficient and the heat leak to the CC. The 3D analysis provided highly accurate values for the heat leak;in some cases, the heat leaks of PTFE and stainless steel wicks showed little differences. In general, the heat flux is concentrated at the boundaries between the casing, the wick, and the grooves;therefore, thermal performance can be optimized by increasing the length of the boundary.展开更多
A mathematical model for heap bioleaching is developed to analyze heat transfer, oxygen flow, target ion distribution and oxidation leaching rate in the heap. The model equations are solved with Comsol Multiphysics so...A mathematical model for heap bioleaching is developed to analyze heat transfer, oxygen flow, target ion distribution and oxidation leaching rate in the heap. The model equations are solved with Comsol Multiphysics software. Numerical simulation results show the following facts： Concentration of oxygen is relatively high along the boundary of the slope, and low in the center part where leaching rate is slow. Temper- ature is relatively low along the slope and reaches the highest along the bottom region near the slope, with difference being more than 6℃. Concentration of target mental ions is the highest in the bottom region near the slope. Oxidation leaching rate is relatively large in the bottom and slope part with a fast reaction rate, and small in the other part with low oxygen concentration.展开更多
In order to analyze the maximum power density error with different heat flux distribution parameter values for double ellipsoidal heat source model, a general expression of double ellipsoidal heat source model was der...In order to analyze the maximum power density error with different heat flux distribution parameter values for double ellipsoidal heat source model, a general expression of double ellipsoidal heat source model was derived .front Goldak double ellipsoidal heat source model, and the error of maximum power density was analyzed under this foundation. The calculation error of thermal cycling parameters caused by the maximum power density error was compared quantitatively by numerical simulation. The results show that for guarantee the accuracy of welding numerical simulation, it is better to introduce an error correction coefficient into the Goldak double ellipsoidal heat source model expression. And, heat flux distribution parameter should get higher value for the higher power density welding methods.展开更多
An approach to design multi-channel cylinder dryer was proposed. The heat transfer performance and flow characteristic under various structural parameters were analyzed. First, an experiment was designed and set up to...An approach to design multi-channel cylinder dryer was proposed. The heat transfer performance and flow characteristic under various structural parameters were analyzed. First, an experiment was designed and set up to measure the condensing heat transfer coefficient and the pressure drop in order to ,~erify the applicability of the Cavallini＇s correlation. Then, the relationship among the count of channels, aspect ratio, spacing ratio, width, height and hydraulic diameter of a channel was given. Finally, the correlation of condensing heat transfer and the homogeneous model was introduced in order to observe the heat transfer performance and flow characteristic of the multi-channel cylinder dryer affected by different structures. The study reveals that the structural parameters including count of channels, aspect ratio, spacing ratio of a channel dramatically influence the condensation heat transfer coefficient and frictional resistance of the steam. Based on the selected paper machine, it is suggested that the overall performance of the multi-channel cylinder dryer is best if the count of channels is 150-200, the aspect ratio is 1 ： 3 and the spacing ratio is 1 ： 1-1 ： 3.展开更多
Drying is a complicated physical process which involves simultaneous heat and mass transfer in the removal of solvents inside propellants.Inappropriate drying techniques may result in the formation of a hard skin laye...Drying is a complicated physical process which involves simultaneous heat and mass transfer in the removal of solvents inside propellants.Inappropriate drying techniques may result in the formation of a hard skin layer near the surface to block the free access of most solvent through for long stick propellants with large web thickness,which lead to lower drying efficiency and worse drying quality.This study aims to gain a comprehensive understanding of drying process and clarify the mechanism of the blocked layer near the propellant surface.A new three-dimensional coupled heat and mass transfer(3D-CHMT)model was successfully developed under transient conditions.The drying experiment results show that the 3DCHMT model could be applied to describe the drying process well since the relative error of the content of solvent between simulation and experiment values is only 5.5%.The solvent behavior simulation demonstrates that the mass transfer process can be divided into super-fast(SF)and subsequent minorfast(MF)stages,and the SF stage is vital to the prevention of the blocked layer against the free access for solvent molecules inside propellant grains.The effective solvent diffusion coefficient(Deff)of the propellant surface initially increases from 3.4×10^(-6)to 5.3×10^(-6)m^(2)/s as the temperature increases,and then decreases to 4.1×10^(-8)m^(2)/s at 60-100 min.The value of Deffof surface between 0-1.4 mm has a unique trend of change compared with other regions,and it is much lower than that of the internal at100 min under simulation conditions.Meanwhile,the temperature of the propellant surface increases rapidly at the SF stage(0-100 min)and then very slowly thereafter.Both the evolution of Deffand temperature distribution demonstrate that the blocked layer near the propellant surface has been formed in the time period of approximately 0-100 min and its thickness is about 1.4 mm.To mitigate the formation of blocked layer and improve its drying quality of finial propellant products effectively,it should be initially dried at lower drying temperature(30-40℃)in 0-100 min and then dried at higher drying temperature(50-60℃)to reduce drying time for later drying process in double base gun propellants.The present results can provide theoretical guidance for drying process and optimization of drying parameters for long stick propellants with large web thickness.展开更多
基金Project (No. 49671050) supported by the National Natural Science Foundation of China.
文摘Coupled transfer of soil water and heat in closed columns of homogeneous red soil was studied under laboratory conditions. A coupled model was constructed using soil physical theory, empirical equations and experimental data to predict the coupled transfer. The results show that transport of soil water was affected by temperature gradient, and the largest net water transport was found in the soil column with initial water content of 0.148 m3 m-3. At the same time, temperature changes with the transport of soil water was in a nonlinear shape as heat parameters were function of water content, and the changes of temperature were positively correlated with the net amount of water transported. Numerical modelling results show that the predicted values of temperature distribution were close to the observed values, while the predicted values of water content exhibited limited deviation at both ends of the soil column due to the slight temperature changes at both ends. It was indicated that the model proposed here was applicable.
文摘A mathematical model of resin flow and temperature variation in the filling stage of the resin transfer molding (RTM) is developed based on the control volume/finite element method (CV/FEM). The effects of the heat transfer and chemical reaction of the resin on the flow and temperature are considered. The numerical algorithm of the resin flow and temperature variation in the process of RTM are studied. Its accuracy and convergence are analyzed. The comparison of temperature variations between experimental results and model predictions is carried out for two RTM cases. Result shows that the model is efficient for evaluating the flow and temperature variation in the filling stage of RTM and there is a good coincidence between theory and experiment.
文摘The objective of this study is to evaluate the difference of the soil water management in mango orchards between the varieties of “Irwin” in Japanand “Nam Dok Mai” inThailand. Field observations were conducted in mango orchards in Okinawa, Japan and Phrao, Thailand to clarify the water management practices. Measurement of the hourly soil water content in Phrao indicated that the irrigation was scarce and the volumetric water content in the soil was maintained almost constant. in the flowering season. This can be the farmers’ practice for flower induction. After the flowering season, irrigation was frequent in order to produce the large fruit. In the harvest season, the soil water content was relatively high because of frequent irrigation and rainfall. In Okinawa, the volumetric water content was maintained at the same level in a relatively deep layer. The result at the5 cmdepth indicated that the farmer carefully controlled the soil water content. In the flowering season, the soil water content was relatively low. While the orchard was managed empirically, the volumetric water content near the soil surface was maintained over 25% during the harvest season. This result indicates that the farmer performed the good soil water management to enhance mango fruit quality even without technical measurement. A numerical model describing the soil water and heat transfers was introduced to predict the farmer’s empirical soil water management in Okinawa. Using the meteorological data in March 2010, the irrigation regime was predicted using the simulated soil water content. In the flowering season, the farmer irrigated when the soil surface water content reached 14%. Based on this criterion for the empirical soil water management, the simulation result indicated that the farmer irrigated four times in this period. The numerical model presented here can be useful for evaluating the differences in water management practices of local farmers.
文摘This study is to understand the impact of operating conditions, especially initial operation temperature (T<sub>ini</sub>) which is set in a high temperature range, on the temperature profile of the interface between the polymer electrolyte membrane (PEM) and the catalyst layer at the cathode (i.e., the reaction surface) in a single cell of polymer electrolyte fuel cell (PEFC). A 1D multi-plate heat transfer model based on the temperature data of the separator measured using the thermograph in a power generation experiment was developed to evaluate the reaction surface temperature (T<sub>react</sub>). In addition, to validate the proposed heat transfer model, T<sub>react</sub> obtained from the model was compared with that from the 3D numerical simulation using CFD software COMSOL Multiphysics which solves the continuity equation, Brinkman equation, Maxwell-Stefan equation, Butler-Volmer equation as well as heat transfer equation. As a result, the temperature gap between the results obtained by 1D heat transfer model and those obtained by 3D numerical simulation is below approximately 0.5 K. The simulation results show the change in the molar concentration of O<sub>2</sub> and H<sub>2</sub>O from the inlet to the outlet is more even with the increase in T<sub>ini</sub> due to the lower performance of O<sub>2</sub> reduction reaction. The change in the current density from the inlet to the outlet is more even with the increase in T<sub>ini</sub> and the value of current density is smaller with the increase in T<sub>ini </sub>due to the increase in ohmic over-potential and concentration over-potential. It is revealed that the change in T<sub>react</sub> from the inlet to the outlet is more even with the increase in T<sub>ini</sub> irrespective of heat transfer model. This is because the generated heat from the power generation is lower with the increase in T<sub>ini </sub>due to the lower performance of O<sub>2</sub> reduction reaction.
基金supported by National Natural Science Foundation of China (Nos.50836007, 10921062)
文摘A modelling study is performed to compare the plasma flow and heat transfer characteristics of low-power arc-heated thrusters （arcjets） for three different propellants： hydrogen, nitrogen and argon. The all-speed SIMPLE algorithm is employed to solve the governing equations, which take into account the effects of compressibility, Lorentz force and Joule heating, as well as the temperature- and pressure-dependence of the gas properties. The temperature, velocity and Mach number distributions calculated within the thruster nozzle obtained with different propellant gases are compared for the same thruster structure, dimensions, inlet-gas stagnant pressure and arc currents. The temperature distributions in the solid region of the anode-nozzle wall are also given. It is found that the flow and energy conversion processes in the thruster nozzle show many similar features for all three propellants. For example, the propellant is heated mainly in the near-cathode and constrictor region, with the highest plasma temperature appearing near the cathode tip; the flow transition from the subsonic to supersonic regime occurs within the constrictor region; the highest axial velocity appears inside the nozzle; and most of the input propellant flows towards the thruster exit through the cooler gas region near the anode-nozzle wall. However, since the properties of hydrogen, nitrogen and argon, especially their molecular weights, specific enthMpies and thermal conductivities, are different, there are appreciable differences in arcjet performance. For example, compared to the other two propellants, the hydrogen arcjet thruster shows a higher plasma temperature in the arc region, and higher axial velocity but lower temperature at the thruster exit. Correspondingly, the hydrogen arcjet thruster has the highest specific impulse and arc voltage for the same inlet stagnant pressure and arc current. The predictions of the modelling are compared favourably with available experimental results.
基金supported by the National Natural Science Foundation of China(Grant No.51276046)the Specialized Research Fund for the Doctoral Program of Higher Education of China(Grant No.20112302110020)+1 种基金the China Postdoctoral Science Foundation(Grant No.2014M561037)the President Fund of University of Chinese Academy of Sciences,China(Grant No.Y3510213N00)
文摘Our previous experimental studies have confirmed that viscoelastic-fluid-based nanofluid(VFBN) prepared by suspending nanoparticles in a viscoelastic base fluid(VBF, behaves drag reduction at turbulent flow state) can reduce turbulent flow resistance as compared with water and enhance heat transfer as compared with VBF. Direct numerical simulation(DNS) is performed in this study to explore the mechanisms of heat transfer enhancement(HTE) and flow drag reduction(DR) for the VFBN turbulent flow. The Giesekus model is used as the constitutive equation for VFBN. Our previously proposed thermal dispersion model is adopted to take into account the thermal dispersion effects of nanoparticles in the VFBN turbulent flow. The DNS results show similar behaviors for flow resistance and heat transfer to those obtained in our previous experiments. Detailed analyses are conducted for the turbulent velocity, temperature, and conformation fields obtained by DNSs for different fluid cases, and for the friction factor with viscous, turbulent, and elastic contributions and heat transfer rate with conductive, turbulent and thermal dispersion contributions of nanoparticles, respectively. The mechanisms of HTE and DR of VFBN turbulent flows are then discussed. Based on analogy theory, the ratios of Chilton–Colburn factor to friction factor for different fluid flow cases are investigated, which from another aspect show the significant enhancement in heat transfer performance for some cases of water-based nanofluid and VFBN turbulent flows.
基金supported by National Natural Science Foundation of China (Nos. 10575127, 10772016)the Doctoral Research Fund of Higher Education of China (No. 20070006022)
文摘A modelling study is performed to investigate the characteristics of both plasma flow and heat transfer of a laminar non-transferred arc argon plasma torch operated at atmospheric and reduced pressure. It is found that the calculated flow fields and temperature distributions are quite similar for both cases at a chamber pressure of 1.0 atm and 0.1 atm. A fully developed flow regime could be achieved in the arc constrictor-tube between the cathode and the anode of the plasma torch at 1.0 atm for all the flow rates covered in this study. However the flow field could not reach the fully developed regime at 0.1 atm with a higher flow rate. The arc-root is always attached to the torch anode surface near the upstream end of the anode, i.e. the abruptly expanded part of the torch channel, which is in consistence with experimental observation. The surrounding gas would be entrained from the torch exit into the torch interior due to a comparatively large inner diameter of the anode channel compared to that of the arc constrictor-tube.
文摘In this paper, a numerical simulation has been carried out on unsteady hydromagnetic free convection near a moving infinite flat plate in a rotating medium. The temperatures involved are assumed to be very high so that the radiative heat transfer is significant, which renders the problem highly non-linear even with the assumption of a differential approximation for the radiative heat flux. A numerical method based on the Nakamura scheme has been employed to obtain the temperature and velocity distributions which are depicted graphically. The effects of the different parameters entering into the problem have been discussed extensively.
文摘This paper illustrates the use of a general purpose differential equation （DE） solver called FlexPDE for the solution heat transfer problems in electric wire. FlexPDE uses the finite element method for the solution of boundary and initial value problems. A flexible input of the governing DE＇s and of material properties functions allows the simulation of non-linear variable behavior quickly and inexpensively. A modeling of temperature distribution in one-dimensional problem, a cross section of an electric wire was simulated. Comparison of those results obtained by FlexPDE with analytical and numerical solutions are done. The results compared well with those obtained from the analytical and numerical methods. The adaptability of the FlexPDE software for solving a variety of problem types was clearly demonstrated.
文摘In this paper, a 3D model of a flat circuit board with a heat generating electronic chip mounted on it has been studied numerically. The conjugate heat transfer including the conduction in the chip and convection with the surrounding fluid has been investigated numerically. Computational fluid dynamics using the finite volume method has been used for modeling the conjugate heat transfer through the chip and the circuit board. Conjugate heat transfer has broad applications in engineering and industrial applications in design of cooling off electronic components. Effects of various inlet velocities have been studied on the heat transfer variation and temperature of the circuit board. Numerical results show that the temperature of the chip reduces as the velocity of the inlet fluid flow increases.
基金Supported by the National Natural Science Foundation of China under Grant No. 49775255.
文摘Theoretical and experimental studies show that during hail growth the heatand mass transfers play a determinant role in growth rates and different structures. However, manynumerical model researchers made extrapolation of the key heat transfer coefficient of the thermalbalance expression from measurements of evaporating water droplets obtained under small Renoldsnumbers (Re ≤ 200) introduced by Ranz and Marshall, leading to great difference from reality. Thispaper is devoted to the parameterization of measured heat transfer coefficients under Renoldsnumbers related to actual hail scales proposed by Zheng, which are then applied, to Hu-He 1D and 3Dmodels for hail growth respectively, indicating that the melting rate of a hailstone is 12%-50%bigger, the evaporation rate is 10%-200% higher and the dry-wet growth rate is 10%-40% larger fromthe present simulations than from the prototype models.
基金National Natural Science Foundation of China(Grant No.U1510131)Key Research and Development Projects of Shanxi Province of China(Grant Nos.201603D121010,201603D111004)+3 种基金Science and Technology Project of Jin Cheng City of China(Grant No.20155010)Youth Program of National Natural Science Fund of China(Grant No.51604181)Project of Young Scholar of Shanxi ProvinceLeading Talent Project of Innovative Entrepreneurial Team of Jiangsu Province(Grant No.51501122)
文摘Currently, when magnesium alloy sheet is rolled, the method of controlling roll temperature is simple and inaccurate. Furthermore, roll temperature has a large influence on the quality of magnesium alloy sheet; therefore, a new model using circular fluid flow control roll temperature has been designed. A fluid heat transfer structure was designed, the heat transfer process model of the fluid heating roll was simplified, and the finite di erence method was used to cal?culate the heat transfer process. Fluent software was used to simulate the fluid?solid coupling heat transfer, and both the trend and regularity of the temperature field in the heat transfer process were identified. The results show that the heating e ciency was much higher than traditional heating methods(when the fluid heat of the roll and tempera?ture distribution of the roll surface was more uniform). Moreover, there was a bigger temperature di erence between the input and the output, and after using reverse flow the temperature di erence decreased. The axial and circum?ferential temperature distributions along the sheet were uniform. Both theoretical calculation results and numerical simulation results of the heat transfer between fluid and roll were compared. The error was 1.8%–12.3%, showing that the theoretical model can both forecast and regulate the temperature of the roll(for magnesium alloy sheets) in the rolling process.
文摘Heat transfer of a capillary evaporator in a loop heat pipe was analyzed through 3D numerical simulations to study the effects of the thermal conductivity of the wick, the contact area between the casing and the wick, and the subcooling in the compensation chamber (CC) on the thermal performance of the evaporator. A pore network model with a distribution of pore radii was used to simulate liquid flow in the porous structure of the wick. To obtain high accuracy, fine meshes were used at the boundaries among the casing, the wick, and the grooves. Distributions of temperature, pressure, and mass flow rate were compared for polytetra-fluoroethylene (PTFE) and stainless steel wicks. The thermal conductivity of the wick and the contact area between the casing and the wick significantly impacted thermal performance of the evaporator heat-transfer coefficient and the heat leak to the CC. The 3D analysis provided highly accurate values for the heat leak;in some cases, the heat leaks of PTFE and stainless steel wicks showed little differences. In general, the heat flux is concentrated at the boundaries between the casing, the wick, and the grooves;therefore, thermal performance can be optimized by increasing the length of the boundary.
基金Project supported by the National Natural Science Foundation of China (Nos. 50934002 and 50774011)the Postdoctoral Science Foundation of China (No. 20090450014)the DoctoralNatural Science Foundation of China (No. 20070008038)
文摘A mathematical model for heap bioleaching is developed to analyze heat transfer, oxygen flow, target ion distribution and oxidation leaching rate in the heap. The model equations are solved with Comsol Multiphysics software. Numerical simulation results show the following facts： Concentration of oxygen is relatively high along the boundary of the slope, and low in the center part where leaching rate is slow. Temper- ature is relatively low along the slope and reaches the highest along the bottom region near the slope, with difference being more than 6℃. Concentration of target mental ions is the highest in the bottom region near the slope. Oxidation leaching rate is relatively large in the bottom and slope part with a fast reaction rate, and small in the other part with low oxygen concentration.
文摘In order to analyze the maximum power density error with different heat flux distribution parameter values for double ellipsoidal heat source model, a general expression of double ellipsoidal heat source model was derived .front Goldak double ellipsoidal heat source model, and the error of maximum power density was analyzed under this foundation. The calculation error of thermal cycling parameters caused by the maximum power density error was compared quantitatively by numerical simulation. The results show that for guarantee the accuracy of welding numerical simulation, it is better to introduce an error correction coefficient into the Goldak double ellipsoidal heat source model expression. And, heat flux distribution parameter should get higher value for the higher power density welding methods.
基金Acknowledgements This project is supported by the National Natural Science Foundation of China （Grant No. 51375286）, Natural Science Basic Research Plan in Shaanxi Province of China （Program No. 2012JZ7002） and the key scientific and technological innovation team fund of Shaanxi Province of China （Program No. 2014KCT- 15）.
文摘An approach to design multi-channel cylinder dryer was proposed. The heat transfer performance and flow characteristic under various structural parameters were analyzed. First, an experiment was designed and set up to measure the condensing heat transfer coefficient and the pressure drop in order to ,~erify the applicability of the Cavallini＇s correlation. Then, the relationship among the count of channels, aspect ratio, spacing ratio, width, height and hydraulic diameter of a channel was given. Finally, the correlation of condensing heat transfer and the homogeneous model was introduced in order to observe the heat transfer performance and flow characteristic of the multi-channel cylinder dryer affected by different structures. The study reveals that the structural parameters including count of channels, aspect ratio, spacing ratio of a channel dramatically influence the condensation heat transfer coefficient and frictional resistance of the steam. Based on the selected paper machine, it is suggested that the overall performance of the multi-channel cylinder dryer is best if the count of channels is 150-200, the aspect ratio is 1 ： 3 and the spacing ratio is 1 ： 1-1 ： 3.
基金supported by the National Natural Science Foundation of China(Grant No.22075146)。
文摘Drying is a complicated physical process which involves simultaneous heat and mass transfer in the removal of solvents inside propellants.Inappropriate drying techniques may result in the formation of a hard skin layer near the surface to block the free access of most solvent through for long stick propellants with large web thickness,which lead to lower drying efficiency and worse drying quality.This study aims to gain a comprehensive understanding of drying process and clarify the mechanism of the blocked layer near the propellant surface.A new three-dimensional coupled heat and mass transfer(3D-CHMT)model was successfully developed under transient conditions.The drying experiment results show that the 3DCHMT model could be applied to describe the drying process well since the relative error of the content of solvent between simulation and experiment values is only 5.5%.The solvent behavior simulation demonstrates that the mass transfer process can be divided into super-fast(SF)and subsequent minorfast(MF)stages,and the SF stage is vital to the prevention of the blocked layer against the free access for solvent molecules inside propellant grains.The effective solvent diffusion coefficient(Deff)of the propellant surface initially increases from 3.4×10^(-6)to 5.3×10^(-6)m^(2)/s as the temperature increases,and then decreases to 4.1×10^(-8)m^(2)/s at 60-100 min.The value of Deffof surface between 0-1.4 mm has a unique trend of change compared with other regions,and it is much lower than that of the internal at100 min under simulation conditions.Meanwhile,the temperature of the propellant surface increases rapidly at the SF stage(0-100 min)and then very slowly thereafter.Both the evolution of Deffand temperature distribution demonstrate that the blocked layer near the propellant surface has been formed in the time period of approximately 0-100 min and its thickness is about 1.4 mm.To mitigate the formation of blocked layer and improve its drying quality of finial propellant products effectively,it should be initially dried at lower drying temperature(30-40℃)in 0-100 min and then dried at higher drying temperature(50-60℃)to reduce drying time for later drying process in double base gun propellants.The present results can provide theoretical guidance for drying process and optimization of drying parameters for long stick propellants with large web thickness.
