期刊文献+
共找到15篇文章
< 1 >
每页显示 20 50 100
用步进锁相扫描技术改进VCO线性及调频带宽稳定性 被引量:2
1
作者 罗世衡 杨丰旭 尹应增 《固体电子学研究与进展》 CAS 北大核心 2020年第1期12-17,共6页
选用HMC703LP4E小数频率综合器与专门设计的有源环路滤波器和商用VCO构成了步进扫描数字锁相环,改进了调频连续波的调频带宽稳定性和调频线性度。对设计的电路进行了制作和测试,实验结果表明在-30^+70℃温度范围内,调频信号的稳定度达到... 选用HMC703LP4E小数频率综合器与专门设计的有源环路滤波器和商用VCO构成了步进扫描数字锁相环,改进了调频连续波的调频带宽稳定性和调频线性度。对设计的电路进行了制作和测试,实验结果表明在-30^+70℃温度范围内,调频信号的稳定度达到了1×10^-6,调频线性度接近于1.0,相位噪声为-90 dBc/Hz/10 kHz。 展开更多
关键词 压控振荡器 锁相环 有源环路滤波器 调频带宽 线性度 频率温度稳定度
在线阅读 下载PDF
采摘机器人位置校正方法研究——基于无线传感网络和超带宽调频方法 被引量:2
2
作者 田二林 李祖贺 《农机化研究》 北大核心 2019年第2期216-219,224,共5页
超带宽雷达是新近出现的一种高分辨率雷达,当信号带宽和其发射中心频率的比大于0.25时,就被称作超带宽,带宽越大,雷达对目标的分辨能力越高。超带宽雷达具有高分辩能力,如果将其使用在采摘机器人定位导航系统中,可以有效地提高采摘机器... 超带宽雷达是新近出现的一种高分辨率雷达,当信号带宽和其发射中心频率的比大于0.25时,就被称作超带宽,带宽越大,雷达对目标的分辨能力越高。超带宽雷达具有高分辩能力,如果将其使用在采摘机器人定位导航系统中,可以有效地提高采摘机器人的定位导航精度和效率。为此,提出了一种基于无线传感网络和超带宽调频技术的采摘机器人位置校正方法,并以实际采摘环境作为研究对象,对采摘机器人的位置校正过程进行了测试。测试结果表明:采用超带宽调频无线传感网络方法,定位校正精度要高于传统的定位算法,且定位效率高,对于新型自动化采摘作业机器人的研究具有重要的指导意义。 展开更多
关键词 采摘机器人 位置校正 无线传感网络 带宽调频
在线阅读 下载PDF
三角波调频引信定距精度锁相优化方法
3
作者 杜英森 黄辉 +1 位作者 王大鹏 张珂 《探测与控制学报》 CSCD 北大核心 2024年第4期58-62,100,共6页
针对传统调频引信在不同环境温度下由于调频带宽和调频线性度变化影响定距精度的问题,提出采用锁相方法产生三角波调频信号提高引信定距精度。该方法基于具有快速波形产生功能的小数分频频率合成器,通过对反馈频率与参考频率进行鉴相、... 针对传统调频引信在不同环境温度下由于调频带宽和调频线性度变化影响定距精度的问题,提出采用锁相方法产生三角波调频信号提高引信定距精度。该方法基于具有快速波形产生功能的小数分频频率合成器,通过对反馈频率与参考频率进行鉴相、锁相,产生调制三角波,经滤波平滑后调谐VCO输出锁相三角波调频信号。试验结果表明,在不同环境温度下,锁相三角波调频引信调频带宽变化远小于传统三角波调频引信,调频线性度优于传统三角波调频引信,由调频带宽变化和调频非线性带来的定距精度误差可以忽略不计,锁相调频可以降低引信定距误差。 展开更多
关键词 锁相调频引信 频率合成器 定距精度 调频带宽 线性度
在线阅读 下载PDF
MSM激光距离成像雷达中线性调频信号的产生 被引量:2
4
作者 余明权 李海廷 +3 位作者 路英宾 高剑波 陈德章 卿光弼 《激光与红外》 CAS CSCD 北大核心 2010年第9期945-949,共5页
MSM激光距离成像雷达将微波雷达中调频测距原理应用到激光雷达,采用一个线性调频的射频副载波调制激光输出强度。本文提出了雷达中调频信号发生器产生宽带线性调频信号的设计思路,并着重阐述DDS+PLL实现宽带线性调频的过程。首先建立四... MSM激光距离成像雷达将微波雷达中调频测距原理应用到激光雷达,采用一个线性调频的射频副载波调制激光输出强度。本文提出了雷达中调频信号发生器产生宽带线性调频信号的设计思路,并着重阐述DDS+PLL实现宽带线性调频的过程。首先建立四阶二型锁相环架构,分析其对DDS产生的线性扫频信号实现频率稳态跟踪的可能性,然后进行锁相环锁频的初步仿真并得到环路基本参数,最后在输入DDS产生的线性扫频信号前提下仿真环路的频率跟踪性能。仿真结果表明四阶二型锁相环实现了对DDS产生的线性扫频信号的频率跟踪及频带扩展,满足了雷达距离精度对线性调频信号的宽频带要求。 展开更多
关键词 调频信号发生器 线性调频带宽 四阶二型锁相环 频率跟踪
在线阅读 下载PDF
高性能声表面波调频振荡器的研究 被引量:3
5
作者 刘春宁 费元春 王亮 《固体电子学研究与进展》 CAS CSCD 北大核心 2002年第3期339-343,共5页
分析了声表面波谐振器的性能 ,论述了声表面波振荡器的工作原理及设计方法 ,最终完成中心频率为797.3 MHz的振荡电路 ,调频带宽 2 MHz(2 5 0 0 PPM)。文中对影响调频带宽、相位噪声的因素进行了分析讨论。
关键词 调频振荡器 声表面波 谐振器 相位噪声 调频带宽
在线阅读 下载PDF
基于BAACMD-NGO-TMSST的变转速滚动轴承故障诊断
6
作者 吴欢 马洁 《机床与液压》 北大核心 2024年第22期227-240,共14页
在变转速工况下,滚动轴承时变故障特征提取困难,且时间重分配的多重同步压缩变换(TMSST)易受噪声干扰,其相关参数的确定不具备自适应性。针对此问题,提出一种基于BAACMD-NGO-TMSST的变转速滚动轴承故障诊断方法。通过BAACMD将故障信号... 在变转速工况下,滚动轴承时变故障特征提取困难,且时间重分配的多重同步压缩变换(TMSST)易受噪声干扰,其相关参数的确定不具备自适应性。针对此问题,提出一种基于BAACMD-NGO-TMSST的变转速滚动轴承故障诊断方法。通过BAACMD将故障信号分解为多个分量,采用基尼指数和包络熵作为综合指标选取最优分量,从而去除噪声干扰;采用北方苍鹰优化算法(NGO)对TMSST进行参数寻优;最后,利用优化后的TMSST对最优分量进行时频分析,并计算最大TF包络谱(TFES)提取故障特征。通过仿真信号和渥太华轴承数据集,验证了所提方法的可行性和有效性;与其他降噪方法对比,BAACMD在降噪方面具有优越性;与其他时频分析方法对比,所提方法具有更好的特征提取效果。 展开更多
关键词 变转速 故障诊断 带宽感知自适应线性调频模态分解(BAACMD) 时间再分配多重同步压缩变换(TMSST)
在线阅读 下载PDF
MSM激光距离成像雷达系统设计与实验研究 被引量:1
7
作者 余明权 高剑波 +5 位作者 方照勋 张华 李海廷 路英宾 陈德章 卿光弼 《激光与红外》 CAS CSCD 北大核心 2011年第6期616-621,共6页
阐述MSM激光距离成像雷达测距成像基本原理,设计并搭建了构成雷达系统核心的调频信号发生器、调幅激光发射器及MSM自混频探测电路,选取MSM探测器上某成像单元进行雷达测距性能及距离分辨率实验,验证了线性调频带宽约400 MHz时距离分辨率... 阐述MSM激光距离成像雷达测距成像基本原理,设计并搭建了构成雷达系统核心的调频信号发生器、调幅激光发射器及MSM自混频探测电路,选取MSM探测器上某成像单元进行雷达测距性能及距离分辨率实验,验证了线性调频带宽约400 MHz时距离分辨率0.375 m的设计指标,为雷达样机下一步实现距离成像奠定了技术基础。 展开更多
关键词 调频信号发生器 调幅激光发射器 MSM自混频探测电路 线性调频带宽 距离分辨率
在线阅读 下载PDF
基于相关干扰抑制的MIMO声呐波形设计
8
作者 刘伟烨 杨益新 刘雄厚 《哈尔滨工程大学学报》 EI CAS CSCD 北大核心 2023年第9期1510-1518,共9页
为了解决在多输入多输出声呐系统中,发射信号无法实现理想的正交问题,要求发射波形之间有尽可能低的互相关峰值电平和自相关旁瓣峰值电平。分析表明:传统的正交频分复用线性调频信号(OFDM-LFM)波形存在较高的ASPL。针对这个问题,采用信... 为了解决在多输入多输出声呐系统中,发射信号无法实现理想的正交问题,要求发射波形之间有尽可能低的互相关峰值电平和自相关旁瓣峰值电平。分析表明:传统的正交频分复用线性调频信号(OFDM-LFM)波形存在较高的ASPL。针对这个问题,采用信号分段设计的思想,提出2种新的波形结构设计方案,分别采用优化子脉冲调频带宽和调频时宽的设计方法,对每个发射阵元的LFM信号结构进行优化设计,在保证波形容易产生的基础上,增加发射信号自由度,仿真结果表明:与传统正交频分复用线性调频信号波形相比,2种方法所设计的波形具有更低的自相关旁瓣峰值电平和互相关峰值电平。 展开更多
关键词 多输入多输出声呐 正交频分复用线性调频 自相关旁瓣峰值电平 互相关峰值电平 分段波形设计 调频带宽 调频时宽 自由度
在线阅读 下载PDF
Digital Coarse Tuning Loop for Wide-Band Fast-Settling Dual-Loop Frequency Synthesizers
9
作者 刘军华 廖怀林 +2 位作者 殷俊 黄如 张兴 《Journal of Semiconductors》 EI CAS CSCD 北大核心 2006年第11期1911-1917,共7页
A new coarse tuning loop for a wide-band dual-loop frequency synthesizer is presented. The coarse tuning structure is composed of two digital modules, including a successive approximation register and a frequency comp... A new coarse tuning loop for a wide-band dual-loop frequency synthesizer is presented. The coarse tuning structure is composed of two digital modules, including a successive approximation register and a frequency comparator with a novel structure. The frequency comparator counts the prescaler cycles within a certain reference time and compares the number with preset data to estimate the VCO frequency. The frequency comparison error is analyzed in detail. Within a given coarse tuning time,our proposed structure shows a comparison error 20 times smaller than that of other reported structures. This structure also reuses the programmable divider as a part of the coarse tuning loop so that the circuit is greatly simplified. 展开更多
关键词 WIDE-BAND coarse tuning loop frequency synthesizer voltage-controlled oscillator
在线阅读 下载PDF
单路话线增加生理信息传输道数的研究
10
作者 王圣峰 尹兴萍 +1 位作者 齐忠民 洪继兴 《生物医学工程研究》 1998年第4期27-29,共3页
众所周知,电话线频带较窄,传输容量有限,使单路话线同步传输多路生理信号变得十分困难。本文介绍的调频带宽基频传输新方法避免了谐波的干扰。
关键词 多道生理信号 调频带宽基频 谐波干扰
全文增补中
Time-Frequency Bandwidth Product Estimation of Sinusoidal Non-Linear Chirp Keying Scheme 被引量:1
11
作者 Zhiguo Sun Xiaoyan Ning Danyang Tian 《China Communications》 SCIE CSCD 2017年第8期184-194,共11页
Sine Non-linear Chirp Keying(SNCK) is a kind of high-efficient modulation scheme, which provides a potential new beamforming method in communication and radar systems. It has been proved to have advantages in some par... Sine Non-linear Chirp Keying(SNCK) is a kind of high-efficient modulation scheme, which provides a potential new beamforming method in communication and radar systems. It has been proved to have advantages in some parameter estimation issues over conventional modulation schemes. In this paper, a novel transform termed as Discrete Sinusoidal Frequency Modulation transform(DSFMT) is proposed. Then, the DSFMT of SNCK signal is deduced and classified into three types, based on which, the time-bandwidth product is estimated by the proposed algorithm. Simulation results show that the noise has a signifi cant impact on the localization of the peak value and the time-bandwidth product can be estimated by using local ratio values when. 展开更多
关键词 parameter estimation time-bandwidth product sine non-linear chirp keying(SNCK) discrete sinusoidal frequency modulation transform(DSFMT)
在线阅读 下载PDF
NEW TYPE OF WINDOWS FOR DIGITAL PULSE COMPRESSION IN FREQUENCY DOMAIN FOR BROADBAND LFM SIGNALS 被引量:3
12
作者 HuangWei FangKeying HuTe XiangJingcheng 《Journal of Electronics(China)》 2005年第2期149-152,共4页
A new type of window called combined window is designed to get higher Ratio of Mainlobe to Sidelobes (RMS) and lower Mainlobe Widening Factor (MWF). Simulation results prove that the new window can solve the contradic... A new type of window called combined window is designed to get higher Ratio of Mainlobe to Sidelobes (RMS) and lower Mainlobe Widening Factor (MWF). Simulation results prove that the new window can solve the contradiction between RMS and MWF better than classic windows. 展开更多
关键词 Linear frequency modulation WINDOWS Pulse compression
在线阅读 下载PDF
Numerical Simulation on Broad-band Er-doped Superfluorescent Fiber Source Filter Using Long Period Chirped Fiber Grating
13
作者 ZHAO Shu-ping WANG Pin-hong +3 位作者 ZHANG Xiao-xia FANG Xing HE Xu-yi XING Zi-bin 《Semiconductor Photonics and Technology》 CAS 2008年第1期28-31,共4页
Given is an analysis of broad-band Er-doped superfluorescent fiber source(EDSFS)filter using long period chirped fiber grating by transmission matrix method.For our EDSFS attenuated amplitude demand and the flattened ... Given is an analysis of broad-band Er-doped superfluorescent fiber source(EDSFS)filter using long period chirped fiber grating by transmission matrix method.For our EDSFS attenuated amplitude demand and the flattened wavelength range demand,proposed are the key factors of designing such filters of high performances.The simulation result demonstrates that such type filters have an enough attenuation to flatten the dramatic increase in output amplified spontaneous emission(ASE)in the wavelength range of 1529nm^1535nm by choosing conformable fiber filter parameters such as chirped degree,original period,induced index change,length of the fiber filter,and then broad-band EDSFS could be achieved. 展开更多
关键词 Er-doped superfluorescent fiber source(EDSFS) numerical simulation long period chirped fibergrating
在线阅读 下载PDF
RECENT PROGRESS IN MULTI-BEAM KLYSTRON IN IECAS
14
作者 Ding Yaogen (Institute of Electronics, Chinese Academy of Sciences, Beijing 100080) 《Journal of Electronics(China)》 2002年第4期441-444,共4页
Recent research progresses in Multi-Beam Klystron (MBK) in IECAS are briefly introduced in the letter. The S-band MBKs of IECAS have peak power of 120-250 kW, average power of 4-9 kW, efficiency of 35-45%, gain of 41-... Recent research progresses in Multi-Beam Klystron (MBK) in IECAS are briefly introduced in the letter. The S-band MBKs of IECAS have peak power of 120-250 kW, average power of 4-9 kW, efficiency of 35-45%, gain of 41-46 dB, beam voltage of 15-19 kV, and weight of 40-45 kg. Some key technical problems of MBK are also described and discussed. Among them,improving the design of MBK to obtain the required bandwidth, raising beam transmission to increase average power, eliminating oscillation and spray spectrum, overcoming window breakdown caused by magic mode, reducing breakdown times of electrongun, are most important things for the practical MBK. Besides, further research work in MBK in IECAS is commented. 展开更多
关键词 Multi-Beam Klystron (MBK) Periodic Reversal Permanent Magnet (PRPM) focusing system Electron gun Oscillation and spray spectrum
在线阅读 下载PDF
Generation of ultra-wide and flat optical frequency comb based on electro-absorption modulator and frequency modulator 被引量:2
15
作者 高迪 李培丽 +1 位作者 邵茜 陈静远 《Optoelectronics Letters》 EI 2016年第2期97-100,共4页
An ultra-wide and flat optical frequency comb(OFC) generation scheme using multiple continuous wave(CW) light sources based on electro-absorption modulator(EAM) and frequency modulator(FM) is proposed. In the scheme, ... An ultra-wide and flat optical frequency comb(OFC) generation scheme using multiple continuous wave(CW) light sources based on electro-absorption modulator(EAM) and frequency modulator(FM) is proposed. In the scheme, each CW light source is broadened and modulated by the first EAM and FM, respectively. The second EAM is introduced to flatten the ultra-wide OFC lines. By setting the wavelength spacing of light sources equal to the bandwidth of sub-OFC, an ultra-wide OFC can be obtained. Principle analysis and simulation for the scheme are performed. The results show that in the case of a single light source, a tunable and flat OFC is obtained. With the increase of light sources, the bandwidth of the generated ultra-wide OFC expands rapidly. In the case of 28 light sources, a 22 GHz ultra-wide OFC with bandwidth of 16.52 THz can be generated. 展开更多
关键词 modulator bandwidth spacing tunable modulated flatness slightly oscillator continually seriously
原文传递
上一页 1 下一页 到第
使用帮助 返回顶部