During the last three decades, the introduction of new construction materials (e.g. RCC (Roller Compacted Concrete), strengthened gabions) has increased the interest for stepped channels and spillways. However stepped...During the last three decades, the introduction of new construction materials (e.g. RCC (Roller Compacted Concrete), strengthened gabions) has increased the interest for stepped channels and spillways. However stepped chute hydraulics is not simple, because of different flow regimes and importantly because of very-strong interactions between entrained air and turbu- lence. In this study, new air-water flow measurements were conducted in two large-size stepped chute facilities with two step heights in each facility to study experimental distortion caused by scale effects and the soundness of result extrapolation to pro- totypes. Experimental data included distributions of air concentration, air-water flow velocity, bubble frequency, bubble chord length and air-water flow turbulence intensity. For a Froude similitude, the results implied that scale effects were observed in both facilities, although the geometric scaling ratio was only Lr=2 in each case. The selection of the criterion for scale effects is a critical issue. For example, major differences (i.e. scale effects) were observed in terms of bubble chord sizes and turbulence levels al- though little scale effects were seen in terms of void fraction and velocity distributions. Overall the findings emphasize that physical modelling of stepped chutes based upon a Froude similitude is more sensitive to scale effects than classical smooth-invert chute studies, and this is consistent with basic dimensional analysis developed herein.展开更多
This study investigated a water supply recovery problem involving municipal water service piping. The problem consisted in recovering full service after network failure, in order to rapidly satisfy all urgent citywide...This study investigated a water supply recovery problem involving municipal water service piping. The problem consisted in recovering full service after network failure, in order to rapidly satisfy all urgent citywide demands. The optimal recovery solution was achieved through the application of so-called network design problems （NDPs）, which are a form of combinatorial optimization problem. However, a conventional NDP is not suitable for addressing urgent situations because （1） it does not utilize the non-failure arcs in the network, and （2） it is solely concerned with stable costs such as flow costs. Therefore, to adapt the technique to such urgent situations, the conventional NDP is here modified to deal with the specified water supply problem. In addition, a numerical illustration using the Sendai water network is presented.展开更多
In order to meet the needs of various tasks of water conservancy project, tunnel excavation under the ground, called hydraulic tunnel. Hydraulic tunnel according to the functions of flood discharge, water diversion, i...In order to meet the needs of various tasks of water conservancy project, tunnel excavation under the ground, called hydraulic tunnel. Hydraulic tunnel according to the functions of flood discharge, water diversion, irrigation, water supply, and the construction diversion tunnel of desilting emptying. Nowadays, water conservancy project on flood discharge runnel design requirements more and more high, so the factors taken into account the amount of spillway tunnel engineering, engineering cost, structure design and other factors to evaluate nature of the spillway tunnel is very important. Therefore, in actual construction, of spillway tunnel of optimization design, whether from the economic point of view, or from the point of view of safety and applicability are necessary. This article mainly from the overall layout of flood discharge tunnel, structure design and so on, and then discuss the optimization scheme.展开更多
This paper describes the use of a numerical and physical modelling study in the design of large breakwaters for a new port and dry dock complex on the southern coast of Oman. The numerical modelling was carried out to...This paper describes the use of a numerical and physical modelling study in the design of large breakwaters for a new port and dry dock complex on the southern coast of Oman. The numerical modelling was carried out to optimise the entrance channel layout with respect to wave penetration into the port and to refine design conditions for the sizing of the primary armour on the breakwaters. Wave conditions inside and outside of the port have been assessed using the 2-dimensional numerical wave penetration model MIKE21 EMS （Elliptic Mild-Slope）. As part of the design process, 3D physical modelling studies were also undertaken at Delft Hydraulics in the Netherlands to confirm the stability of the armour on the trunk and roundhead of the breakwaters and to verify the influence of the deep approach channel on stability. The opportunity was taken to extend the physical model tests to assess the influence of the deep channel on wave penetration through the port entrance. The paper focuses on the influence of the deep channel on wave conditions in the entrance to the port and compares the results from the numerical and physical modelling.展开更多
基金Project supported by the National Council for Science and Tech-nology of Mexico (CONACYT)
文摘During the last three decades, the introduction of new construction materials (e.g. RCC (Roller Compacted Concrete), strengthened gabions) has increased the interest for stepped channels and spillways. However stepped chute hydraulics is not simple, because of different flow regimes and importantly because of very-strong interactions between entrained air and turbu- lence. In this study, new air-water flow measurements were conducted in two large-size stepped chute facilities with two step heights in each facility to study experimental distortion caused by scale effects and the soundness of result extrapolation to pro- totypes. Experimental data included distributions of air concentration, air-water flow velocity, bubble frequency, bubble chord length and air-water flow turbulence intensity. For a Froude similitude, the results implied that scale effects were observed in both facilities, although the geometric scaling ratio was only Lr=2 in each case. The selection of the criterion for scale effects is a critical issue. For example, major differences (i.e. scale effects) were observed in terms of bubble chord sizes and turbulence levels al- though little scale effects were seen in terms of void fraction and velocity distributions. Overall the findings emphasize that physical modelling of stepped chutes based upon a Froude similitude is more sensitive to scale effects than classical smooth-invert chute studies, and this is consistent with basic dimensional analysis developed herein.
文摘This study investigated a water supply recovery problem involving municipal water service piping. The problem consisted in recovering full service after network failure, in order to rapidly satisfy all urgent citywide demands. The optimal recovery solution was achieved through the application of so-called network design problems （NDPs）, which are a form of combinatorial optimization problem. However, a conventional NDP is not suitable for addressing urgent situations because （1） it does not utilize the non-failure arcs in the network, and （2） it is solely concerned with stable costs such as flow costs. Therefore, to adapt the technique to such urgent situations, the conventional NDP is here modified to deal with the specified water supply problem. In addition, a numerical illustration using the Sendai water network is presented.
文摘In order to meet the needs of various tasks of water conservancy project, tunnel excavation under the ground, called hydraulic tunnel. Hydraulic tunnel according to the functions of flood discharge, water diversion, irrigation, water supply, and the construction diversion tunnel of desilting emptying. Nowadays, water conservancy project on flood discharge runnel design requirements more and more high, so the factors taken into account the amount of spillway tunnel engineering, engineering cost, structure design and other factors to evaluate nature of the spillway tunnel is very important. Therefore, in actual construction, of spillway tunnel of optimization design, whether from the economic point of view, or from the point of view of safety and applicability are necessary. This article mainly from the overall layout of flood discharge tunnel, structure design and so on, and then discuss the optimization scheme.
文摘This paper describes the use of a numerical and physical modelling study in the design of large breakwaters for a new port and dry dock complex on the southern coast of Oman. The numerical modelling was carried out to optimise the entrance channel layout with respect to wave penetration into the port and to refine design conditions for the sizing of the primary armour on the breakwaters. Wave conditions inside and outside of the port have been assessed using the 2-dimensional numerical wave penetration model MIKE21 EMS （Elliptic Mild-Slope）. As part of the design process, 3D physical modelling studies were also undertaken at Delft Hydraulics in the Netherlands to confirm the stability of the armour on the trunk and roundhead of the breakwaters and to verify the influence of the deep approach channel on stability. The opportunity was taken to extend the physical model tests to assess the influence of the deep channel on wave penetration through the port entrance. The paper focuses on the influence of the deep channel on wave conditions in the entrance to the port and compares the results from the numerical and physical modelling.
