直通光路型磁光式光学电流传感器(magneto-optical current sensor,MOCS)因具有体积小,测量准确度高等多种优点,在智能电网中有广阔应用前景。然而,由于无法构成闭合光路,外磁场干扰一直是制约直通光路型磁光式光学电流传感器实用化的...直通光路型磁光式光学电流传感器(magneto-optical current sensor,MOCS)因具有体积小,测量准确度高等多种优点,在智能电网中有广阔应用前景。然而,由于无法构成闭合光路,外磁场干扰一直是制约直通光路型磁光式光学电流传感器实用化的重要因素。为解决此问题,该文提出光学电流传感层叠抗外磁干扰技术。首先通过定义非连续积分路径,积分张角等概念,推导出电流位于非连续闭合路径内外时对应的磁场积分表达式,进而建立适用于含任意数量磁光传感单元、按对称多边形方式布置的MOCS所受外磁干扰分析的数学模型,提出闭合路径中心偏转模型,并得出最佳中心偏转角。在此基础上提出一种新型的层叠式MOCS结构,基本抗御传感结构外任意位置电流给MOCS带来的磁场干扰。其次,提出通用的层叠式MOCS测量误差分析方法,从理论上证明层叠式MOCS满足工程需求及标准。分别建立层叠式MOCS数值仿真模型及COMSOL有限元仿真模型。仿真结果表明,在不同干扰条件下,层叠式MOCS的测量误差均低于0.2%,证明此结构能够有效降低存在外磁干扰时MOCS的测量误差。最后,设计并搭建相应的层叠式MOCS实验平台并进行相应实验。实验结果表明,新型层叠式MOCS在多种干扰情况下其测量误差均小于0.2%,证明了所提数学模型正确性及层叠式结构应用于提高MOCS抗外磁干扰能力时的有效性。展开更多
A new approach to conductive electromagnetic interference （EMI） noise source modeling, i. e. the source internal impedance extraction, is presented. First, the impedance magnitude is achieved through an exciting pro...A new approach to conductive electromagnetic interference （EMI） noise source modeling, i. e. the source internal impedance extraction, is presented. First, the impedance magnitude is achieved through an exciting probe and a detecting probe, or through calculations based on insertion loss measurement results when inserting a series nigh-value known impedance or a shunt low-value known impedance in the circuit. Then the impedance phase is extracted by the Hilbert transform （HT） of the logarithm of the obtained impedance magnitude. Performance studies show that the estimated phase error can increase greatly at a zero frequency in the Hilbert transform because of the existence of a singular point, and this effect can be eliminated by introducing a zero-point when the noise source does not include a series-connected capacitive component. It is also found that when the frequency is nigher than 150 kHz, the estimated phase error is not sensitive to the inductive source but sensitive to the capacitive source. Finally, under the conditions of the same measurement accuracies for impedance magnitude, the accuracy of complex impedance based on the HT can be improved about 10 times when compared with the accuracy of estimated parameters based on the impedance magnitude fitting method （IMFM）.展开更多
To promote the modeling standardization process of the integrated circuits, an improved electrical simulation model for a direct power injection （DPI） setup which was used to measure the conducted immunity of a 16-b...To promote the modeling standardization process of the integrated circuits, an improved electrical simulation model for a direct power injection （DPI） setup which was used to measure the conducted immunity of a 16-bit microcontroller to radio frequency aggression was investigated. Based on the existing model of the same microcontroller, the PDN module was modified by adding the core, PLL and MD network models, which could reflect the actual electric distribution situation within the microcontroller more accurately. By comparing the simulation results with the measurement results, the effectiveness of the modified model can be improved to 500 MHz, and its uncertainty is within ＋1.8 dB （＋2 dB is acceptable）. Then, to improve the simulation accuracy of the complete model in the high frequency range, the I/O model which contained the dynamic and nonlinear characteristics reflecting the variation of the internal impedance of the microcontroller with increasing the frequency of the external noise was introduced. By comparing the simulation results with the measurement results, the effectiveness of the second modified model can be improved up to 1.4 GHz with the uncertainty of ~1.8 dB. Thus, a conclusion can be reached that the proposed model can be applied to a much wider frequency range with a smaller uncertainty than the latest model of the similar type. Furthermore, associated with the electromagnetic emission testing platform model, the PDN module can also be used to predict the electromagnetic conducted and radiated emission characteristics. This modeling method can also be applied to other integrated circuits, which is very helpful to the standardization of the IC electromagnetic compatibility （EMC） modeling process.展开更多
The surface modification on the AA6082 Al?Mg?Si aging-hardenable aluminum alloy was investigated by electricaldischarge alloying (EDA) process. Kerosene, used as a dielectric fluid, was pyrolytically decomposed into c...The surface modification on the AA6082 Al?Mg?Si aging-hardenable aluminum alloy was investigated by electricaldischarge alloying (EDA) process. Kerosene, used as a dielectric fluid, was pyrolytically decomposed into carbon for the formationof a self-lubricated carbide layer on the aluminum alloy surface during EDA process. Transmission electron microscopy (TEM)image found that the self-lubricated carbide layer was a multi-phase material with carbides and graphite. As a result, theEDA-modified aluminum alloy had a negligible wear rate of ~2?10?4 mg/m (c. f. ~1.1?10?2 mg/m for aluminum alloy substrate).Notably, a new characteristic was found that the EDA-processed carbide layer was a soft magnet, which improved theelectromagnetic interference (EMI) shielding performance of the alloy.展开更多
Due to the strong electromagnetic interferences and human interference,traditional electromagnetic methods cannot obtain high quality resistivity data of mineral deposits in Chinese mines.The wide field electromagneti...Due to the strong electromagnetic interferences and human interference,traditional electromagnetic methods cannot obtain high quality resistivity data of mineral deposits in Chinese mines.The wide field electromagnetic method(WFEM),in which the pseudo-random signal is taken as the transmitter source,can extract high quality resistivity data in areas with sever interference by only measuring the electric field component.We use the WFEM to extract the resistivity information of the Dongguashan mine in southeast China.Compared with the audio magnetotelluric(AMT)method,and the controlled source audio-frequency magnetotelluric(CSAMT) method,the WFEM can obtain data with higher quality and simpler operations.The inversion results indicate that the WFEM can accurately identify the location of the main ore-body,which can be used for deep mine exploration in areas with strong interference.展开更多
In the last years, the production of optical fibers cables has made possible the development of a range of spectroscopic probes for in situ analysis performing beyond nondestructive tests, environmental monitoring, se...In the last years, the production of optical fibers cables has made possible the development of a range of spectroscopic probes for in situ analysis performing beyond nondestructive tests, environmental monitoring, security investigation, application in radiotherapy for dose monitoring, verification and validation. In this work, a system using an optical fiber cable to electromagnetic signal transmission from a NaI（TI） radiation detector is presented. The innovative device takes advantage mainly of the optical fibers large passband, small signal attenuation and immunity to electromagnetic interference to application for radiation detection systems. The main aim was to simplify the detection system making it to reach areas where the conventional device cannot access due to its lack of mobility and external dimensions. Some tests with this innovative system are presented and the results stimulate the continuity of the researches.展开更多
Coal mining monitoring system has been enforcing tests for the immunity of Electromagnetic Compatibility(EMC) since 2006.However,not all monitoring substations can pass the Electrical Fast Transient/Burst(EFT/B) immun...Coal mining monitoring system has been enforcing tests for the immunity of Electromagnetic Compatibility(EMC) since 2006.However,not all monitoring substations can pass the Electrical Fast Transient/Burst(EFT/B) immunity test and the explosion-proof test simultaneously.In order to enhance EMC,the EFT/B interfere transmission model was presented at the substation power port,after the EFT/B test method was used to analyze the monitoring substation power ports.Hence,a low-pass filter was designed by using the simulation software PIPICE and an anti-jamming method was proposed by way of a parallel connection of the discharge interfere circuit and the low-pass filter.The improved complex EMI filter was made up of an interference discharge device and a filter.The dynamic equivalent circuit was proposed for the EFT/B immunity test.As a result,the monitoring substation has passed the EFT/B immunity and explosion-proof tests with the complex filter.It is concluded that the complex EMI filter has significantly enhanced the immunity of the coal mining monitoring system.展开更多
文摘直通光路型磁光式光学电流传感器(magneto-optical current sensor,MOCS)因具有体积小,测量准确度高等多种优点,在智能电网中有广阔应用前景。然而,由于无法构成闭合光路,外磁场干扰一直是制约直通光路型磁光式光学电流传感器实用化的重要因素。为解决此问题,该文提出光学电流传感层叠抗外磁干扰技术。首先通过定义非连续积分路径,积分张角等概念,推导出电流位于非连续闭合路径内外时对应的磁场积分表达式,进而建立适用于含任意数量磁光传感单元、按对称多边形方式布置的MOCS所受外磁干扰分析的数学模型,提出闭合路径中心偏转模型,并得出最佳中心偏转角。在此基础上提出一种新型的层叠式MOCS结构,基本抗御传感结构外任意位置电流给MOCS带来的磁场干扰。其次,提出通用的层叠式MOCS测量误差分析方法,从理论上证明层叠式MOCS满足工程需求及标准。分别建立层叠式MOCS数值仿真模型及COMSOL有限元仿真模型。仿真结果表明,在不同干扰条件下,层叠式MOCS的测量误差均低于0.2%,证明此结构能够有效降低存在外磁干扰时MOCS的测量误差。最后,设计并搭建相应的层叠式MOCS实验平台并进行相应实验。实验结果表明,新型层叠式MOCS在多种干扰情况下其测量误差均小于0.2%,证明了所提数学模型正确性及层叠式结构应用于提高MOCS抗外磁干扰能力时的有效性。
基金The Natural Science Foundation of Jiangsu Province(No.BK2008429)Open Research Foundation of State Key Laboratory of Millimeter Waves of Southeast University(No.K200603)+1 种基金China Postdoctoral Science Foundation(No.20080431126)Jiangsu Postdoctoral Science Foundation(No.2007-337)
文摘A new approach to conductive electromagnetic interference （EMI） noise source modeling, i. e. the source internal impedance extraction, is presented. First, the impedance magnitude is achieved through an exciting probe and a detecting probe, or through calculations based on insertion loss measurement results when inserting a series nigh-value known impedance or a shunt low-value known impedance in the circuit. Then the impedance phase is extracted by the Hilbert transform （HT） of the logarithm of the obtained impedance magnitude. Performance studies show that the estimated phase error can increase greatly at a zero frequency in the Hilbert transform because of the existence of a singular point, and this effect can be eliminated by introducing a zero-point when the noise source does not include a series-connected capacitive component. It is also found that when the frequency is nigher than 150 kHz, the estimated phase error is not sensitive to the inductive source but sensitive to the capacitive source. Finally, under the conditions of the same measurement accuracies for impedance magnitude, the accuracy of complex impedance based on the HT can be improved about 10 times when compared with the accuracy of estimated parameters based on the impedance magnitude fitting method （IMFM）.
基金Project(2007dfa71250) supported by the International Science and Technology Cooperative Program of ChinaProject(20062250) supported by the Doctor Fund of North China Electric Power University, China
文摘To promote the modeling standardization process of the integrated circuits, an improved electrical simulation model for a direct power injection （DPI） setup which was used to measure the conducted immunity of a 16-bit microcontroller to radio frequency aggression was investigated. Based on the existing model of the same microcontroller, the PDN module was modified by adding the core, PLL and MD network models, which could reflect the actual electric distribution situation within the microcontroller more accurately. By comparing the simulation results with the measurement results, the effectiveness of the modified model can be improved to 500 MHz, and its uncertainty is within ＋1.8 dB （＋2 dB is acceptable）. Then, to improve the simulation accuracy of the complete model in the high frequency range, the I/O model which contained the dynamic and nonlinear characteristics reflecting the variation of the internal impedance of the microcontroller with increasing the frequency of the external noise was introduced. By comparing the simulation results with the measurement results, the effectiveness of the second modified model can be improved up to 1.4 GHz with the uncertainty of ~1.8 dB. Thus, a conclusion can be reached that the proposed model can be applied to a much wider frequency range with a smaller uncertainty than the latest model of the similar type. Furthermore, associated with the electromagnetic emission testing platform model, the PDN module can also be used to predict the electromagnetic conducted and radiated emission characteristics. This modeling method can also be applied to other integrated circuits, which is very helpful to the standardization of the IC electromagnetic compatibility （EMC） modeling process.
文摘The surface modification on the AA6082 Al?Mg?Si aging-hardenable aluminum alloy was investigated by electricaldischarge alloying (EDA) process. Kerosene, used as a dielectric fluid, was pyrolytically decomposed into carbon for the formationof a self-lubricated carbide layer on the aluminum alloy surface during EDA process. Transmission electron microscopy (TEM)image found that the self-lubricated carbide layer was a multi-phase material with carbides and graphite. As a result, theEDA-modified aluminum alloy had a negligible wear rate of ~2?10?4 mg/m (c. f. ~1.1?10?2 mg/m for aluminum alloy substrate).Notably, a new characteristic was found that the EDA-processed carbide layer was a soft magnet, which improved theelectromagnetic interference (EMI) shielding performance of the alloy.
基金Project(2018YFC0807802)supported by the National Key R&D Program of ChinaProject(41874081)supported by the National Natural Science Foundation of China
文摘Due to the strong electromagnetic interferences and human interference,traditional electromagnetic methods cannot obtain high quality resistivity data of mineral deposits in Chinese mines.The wide field electromagnetic method(WFEM),in which the pseudo-random signal is taken as the transmitter source,can extract high quality resistivity data in areas with sever interference by only measuring the electric field component.We use the WFEM to extract the resistivity information of the Dongguashan mine in southeast China.Compared with the audio magnetotelluric(AMT)method,and the controlled source audio-frequency magnetotelluric(CSAMT) method,the WFEM can obtain data with higher quality and simpler operations.The inversion results indicate that the WFEM can accurately identify the location of the main ore-body,which can be used for deep mine exploration in areas with strong interference.
文摘In the last years, the production of optical fibers cables has made possible the development of a range of spectroscopic probes for in situ analysis performing beyond nondestructive tests, environmental monitoring, security investigation, application in radiotherapy for dose monitoring, verification and validation. In this work, a system using an optical fiber cable to electromagnetic signal transmission from a NaI（TI） radiation detector is presented. The innovative device takes advantage mainly of the optical fibers large passband, small signal attenuation and immunity to electromagnetic interference to application for radiation detection systems. The main aim was to simplify the detection system making it to reach areas where the conventional device cannot access due to its lack of mobility and external dimensions. Some tests with this innovative system are presented and the results stimulate the continuity of the researches.
基金supported by the National Natural Science Foundation of China (No.50674093)the Pingdingshan Coal Co.Ltd. The EMI distribution measurements were obtained from several coal mines of the Pingdingshan Coal Co.
文摘Coal mining monitoring system has been enforcing tests for the immunity of Electromagnetic Compatibility(EMC) since 2006.However,not all monitoring substations can pass the Electrical Fast Transient/Burst(EFT/B) immunity test and the explosion-proof test simultaneously.In order to enhance EMC,the EFT/B interfere transmission model was presented at the substation power port,after the EFT/B test method was used to analyze the monitoring substation power ports.Hence,a low-pass filter was designed by using the simulation software PIPICE and an anti-jamming method was proposed by way of a parallel connection of the discharge interfere circuit and the low-pass filter.The improved complex EMI filter was made up of an interference discharge device and a filter.The dynamic equivalent circuit was proposed for the EFT/B immunity test.As a result,the monitoring substation has passed the EFT/B immunity and explosion-proof tests with the complex filter.It is concluded that the complex EMI filter has significantly enhanced the immunity of the coal mining monitoring system.
