The single event transient effects of the operational amplifier LM124J and the optocoupler HCPL 5231 are investigated by a pulsed laser test facility. The relation of transient pulse shape to pulsed laser equivalent L...The single event transient effects of the operational amplifier LM124J and the optocoupler HCPL 5231 are investigated by a pulsed laser test facility. The relation of transient pulse shape to pulsed laser equivalent LET is tested,the sensitive areas of the SET effects are identified in voltage follower application mode of LM124J, and the mechanism is initially analyzed. The transient amplitude and duration of HCPL5231 at various equivalent LET are examined,and the SET cross-section is measured. The results of our test and heavy ion experimental data coincide closely,indicating that a pulsed laser test facility is a valid tool for single event effect evaluation.展开更多
Drainage canals are engineering structures widely used for debris flow mitigation.When passing through a drainage canal,debris flow usually scours the gully bed at the back of the rib sill of the drainage canal,which ...Drainage canals are engineering structures widely used for debris flow mitigation.When passing through a drainage canal,debris flow usually scours the gully bed at the back of the rib sill of the drainage canal,which leads to failure of the rib sill.Therefore,the scour depth at the back of the rib sill is an important design problem and it is related to the economic benefits of engineering and service years.To explore the law of the depth of the scour pit after debris flow through drainage canal ribs,we first proposed a formula for the calculation of the maximum scour depth at the back of a rib sill based on energy conservation.We then conducted a series of simulation experiments to test the proposed formula.The experimental results show that the scour depth,trench slope and the distance between ribs all increase with a decrease in debris flow density.We then compared the results of experiments and formula calculations.Through the testing analysis,we found that the calculation results of the conductedformula correspond with the experimental results better.Finally,taking Qipan Gully as an example,we designed the ultimate depth of a drainage canal for debris flow using the calculation formula.展开更多
The dynamic performance and the stability are essential for a system. A new circuit topology used for electrical discharge machining (EDM) power and made up of complex-pulse (voltage-pulse and current-pulse) is presen...The dynamic performance and the stability are essential for a system. A new circuit topology used for electrical discharge machining (EDM) power and made up of complex-pulse (voltage-pulse and current-pulse) is presented. The large-signal model of it is also derived. Based on the comprehensive analysis of the system model, the compensator is designed to make the system match better and to improve its dynamic performance and the stability under perturbations. Finally, the design methods and the analysis are verified by simulation and experimental results.展开更多
Titanium nitride thin films were deposited on silicon by high power impulse magnetron sputtering(HiPIMS)method at different frequencies(162-637 Hz)and pulse-on time(60-322μs).Response surface methodology(RSM)was empl...Titanium nitride thin films were deposited on silicon by high power impulse magnetron sputtering(HiPIMS)method at different frequencies(162-637 Hz)and pulse-on time(60-322μs).Response surface methodology(RSM)was employed to study the simultaneous effect of frequency and pulse-on time on the current waveforms and the crystallographic orientation,microstructure,and in particular,the deposition rate of titanium nitride at constant time and average power equal to 250 W.The crystallographic structure and morphology of deposited films were analyzed using XRD and FESEM,respectively.It is found that the deposition rate of HiPIMS samples is tremendously dependent on pulse-on time and frequency of pulses where the deposition rate changes from 4.5 to 14.5 nm/min.The regression equations and analyses of variance(ANOVA)reveal that the maximum deposition rate(equal to(17±0.8)nm/min)occurs when the frequency is 537 Hz and pulse-on time is 212μs.The experimental measurement of the deposition rate under this condition gives rise to the deposition rate of 16.7 nm/min that is in good agreement with the predicted value.展开更多
A method of improving the accuracy of laser pulse range finding from ±10 m to ±1 m inexpensively by means of time scale up is described. Time scale up can stretch the entire flight time by a factor of 1 00...A method of improving the accuracy of laser pulse range finding from ±10 m to ±1 m inexpensively by means of time scale up is described. Time scale up can stretch the entire flight time by a factor of 1 000 and then the stretched result is counted to calculate the distance. The use of this technique decreases the resolution of counting from nanosecond to microsecond, therefore a separate counting oscillator followed by an interpolation operation is unnecessary. This technique can improve the accuracy of laser pulse range finding inexpensively and effectively.展开更多
The erosion shape and the law of development of debris flow sabo dam downstream is a weak part in the study on debris flow erosion. The shape and development of scour pit have an important effect on the stability and ...The erosion shape and the law of development of debris flow sabo dam downstream is a weak part in the study on debris flow erosion. The shape and development of scour pit have an important effect on the stability and safety of debris flow sabo dam, which determines the foundational depth of the dam and the design of protective measures downstream. Study on the scouring law of sabo dam downstream can evaluate the erosion range and reasonably arrange auxiliary protective engineering. Therefore, a series of flume experiments are carried out including different debris flow characteristics （density is varying from 1.5 t/m3 to 2.1 t/m~） and different gully longitudinal slopes. The result shows that the scour pit appears as an oval shape in a plane and deep in the middle while superficial at the ends in the longitudinal section, the position of the maximum depth point moves towards downstream with an increase of flume slope angle. The maximum depth of scour pit is mainly affected by the longitudinal slope of gully, density of debris flow, and the characteristics of gully composition （particle size and the viscosity of soil）. The result also indicates that the viscosity of soil will weaken the erosion extent. The interior slopes of scour pit are different between the upstream and the downstream, and the downstream slope is smaller than the upper one. For the viscous and non-viscous sands with the same distribution of gradation, the interior slope of non- viscous sand is smaller than the viscous sand.According to tbe regression analysis on the experimental data, the quantitative relationship between the interior slope of scour pit, slope of repose under water and the longitudinal slope of gully is established and it can be used to calculate the interior slope of scour pit. The results can provide the basis for the parameter design of the debris flow control engineering foundation.展开更多
Impact property of the sandwich composite with aluminum foam core was investigated by experiment and simulation analysis. Impact energies of 50, 70 and 100 J were applied to the specimens in impact tests. The results ...Impact property of the sandwich composite with aluminum foam core was investigated by experiment and simulation analysis. Impact energies of 50, 70 and 100 J were applied to the specimens in impact tests. The results show that the striker penetrates the upper face sheet, causing the core to be damaged at 50 J test but the lower face sheet remains intact with no damage. At 70 J test, the striker penetrates the upper face sheet and the core,and causes the lower face sheet to be damaged. Finally at 100 J test, the striker penetrates both the upper face sheet and the core, and even the lower face sheet. The experimental and simulation results agree with each other. By the confirmation with the experimental results, all these simulation results can be applied on structure study of real sandwich composite with aluminum foam core effectively.展开更多
Bridge pressure flow scour at clear water threshold condition is studied theoretically and experimentally.The flume experiments reveal that the measured scour profiles under a bridge are more or less 2-dimensional;all...Bridge pressure flow scour at clear water threshold condition is studied theoretically and experimentally.The flume experiments reveal that the measured scour profiles under a bridge are more or less 2-dimensional;all the measured scour profiles can be described by two similarity equations,where the horizontal distance is scaled by the deck width while the local scour by the maximum scour depth;the maximum scour position is located just under the bridge about 15% deck width from the downstream deck edge;the scour begins at about one deck width upstream the bridge while the deposition occurs at about 2.5 deck widths downstream the bridge;and the maximum scour depth decreases with increas-ing sediment size,but increases with deck inundation.The theoretical analysis shows that:bridge scour can be divided into three cases,i.e.downstream unsubmerged,partially submerged,and totally submerged.For downstream unsubmerged flows,the maximum bridge scour depth is an open-channel problem where the conventional methods in terms of critical velocity or bed shear stress can be applied;for partially and totally submerged flows,the equilibrium maximum scour depth can be described by a scour and an inundation similarity number,which has been confirmed by experiments with two decks and two sediment sizes.For application,a design and field evaluation procedure with examples is presented,including the maximum scour depth and scour profile.展开更多
Proposed is a novel optical pulse compression technique based on high-doped erbium fiber amplifier and standard single-mode fiber(SMF). We used the amplifier with the erbium ion concentration of 6.3×10-3 to ampli...Proposed is a novel optical pulse compression technique based on high-doped erbium fiber amplifier and standard single-mode fiber(SMF). We used the amplifier with the erbium ion concentration of 6.3×10-3 to amplify a hyperbolic secant pulse from a regeneratively mode-locked fiber laser. The central wavelength, pulsewidth and peak power of the pulse are 1 550 nm, 12.5 ps and 3 mW, respectively. Then the amplified pulse with peak power level corresponding to a higher-order soliton is compressed when it propagates through a 3-km-long single-mode fiber. Studied are the compressed pulses under different pump powers and fiber lengths. The results show that it can get a narrower pulse, and solve the difficulty that pulses at low power can not be compressed directly in the fiber. And the construct is compact.展开更多
To research the anchoring effect of large deformation bolt,tensile and drawing models are established.Then,the evolution laws of drawing force,bolt axial force and interfacial shear stress are analyzed.Additionally,th...To research the anchoring effect of large deformation bolt,tensile and drawing models are established.Then,the evolution laws of drawing force,bolt axial force and interfacial shear stress are analyzed.Additionally,the influence of structure element position on the anchoring effect of large deformation bolt is discussed.At last,the energy-absorbing support mechanism is discussed.Results show that during the drawing process of normal bolt,drawing force,bolt axial force and interfacial shear stress all gradually increase as increasing the drawing displacement,but when the large deformation bolt enters the structural deformation stage,these three values will keep stable;when the structure element of large deformation bolt approaches the drawing end,the fluctuation range of drawing force decreases,the distributions of bolt axial force and interfacial shear stress of anchorage section are steady and the increasing rate of interfacial shear stress decreases,which are advantageous for keeping the stress stability of the anchorage body.During the working process of large deformation bolt,the strain of bolt body is small,the working resistance is stable and the distributions of bolt axial force and interfacial shear stress are steady.When a rock burst event occurs,the bolt and bonding interface cannot easily break,which weakens the dynamic disaster degree.展开更多
We establish an equivalent cascaded semiconductor optical amplifier system model to analyze the characteristics of the double loop optical buffer （DLOB）. The theoretical analysis finds that the performance of the DL...We establish an equivalent cascaded semiconductor optical amplifier system model to analyze the characteristics of the double loop optical buffer （DLOB）. The theoretical analysis finds that the performance of the DLOB can be improved by inserted amplifying process in an interval of some cycles. The experiment demonstrates that the buffered cycles can be improved from 20 to 50 and the bit error rate is less than 10-9 by inserting amplifying process in an interval of about 10 cycles.展开更多
The 12 mm-thick Ti−6Al−4V(TC4)titanium alloy plates were welded using keyhole tungsten inert gas(K-TIG)welding at various heat inputs.The microstructure,grain boundary(GB)characteristics and mechanical properties of t...The 12 mm-thick Ti−6Al−4V(TC4)titanium alloy plates were welded using keyhole tungsten inert gas(K-TIG)welding at various heat inputs.The microstructure,grain boundary(GB)characteristics and mechanical properties of the weld metal zone(WMZ)were analyzed.The test results show that the K-TIG welds are well formed,and no obvious defects are observed when the heat input is 2.30−2.62 kJ/mm.When the heat input gradually increases,αlaths increase in length,andα′phase and residualβphase are reduced.The electron backscatter diffraction(EBSD)test results indicate that the high-angle GB proportion in the WMZ increases with the increase of heat input.The tensile strength of the WMZ gradually decreases and the elongation of the WMZ increases when the heat input increases from 2.30 to 2.62 kJ/mm.The impact toughness of the WMZ increases as the heat input increases.展开更多
Isotopic tracers and water quality indicators （TDS （Total Dissolved Solid）, Cl^- and NO3^-contents） were used to characterize the recharge and control of the quality of groundwater in the alluvial aquifer beneath ...Isotopic tracers and water quality indicators （TDS （Total Dissolved Solid）, Cl^- and NO3^-contents） were used to characterize the recharge and control of the quality of groundwater in the alluvial aquifer beneath of the N＇djamena city. For this study, a total of 92 waters samples were taken and this included 67 wells, 21 pumps and 4 surface waters. Some groundwater has 6180 and 62H values close to those of the city of N＇djamena and/or the Chad river rains. However, all sampled points are below the Global Meteoric Water Line reflecting their evaporated characters. The interpretation of the isotopic tracers highlights that the recharge of the analyzed ground waters may result from two major mechanisms： （1） direct infiltration of local precipitation; （2） lateral inflow of river waters. The upper aquifer is the most vulnerable to pollution, especially during the recharge period. This pollution is due to the leaching of soils during the rainy season and the rise of the groundwater level which accompanies the overflowing of the Chad and causes the leaching of the polluted horizons of the unsaturated zone. In contrast, the lower aquifer has acceptable concentrations of solutes.展开更多
In order to simplify the structure of the cold end of the pulse tube refrigerator (PTR) and have a better utilization of the cold energy of the system, a one-stage four-valve pulse tube refrigerator (FVPTR) with an &q...In order to simplify the structure of the cold end of the pulse tube refrigerator (PTR) and have a better utilization of the cold energy of the system, a one-stage four-valve pulse tube refrigerator (FVPTR) with an "L" type pulse tube structure and two orifice valves at the hot end of pulse tube has been constructed. Verification experiments show that the two orifice valve structure performs better than one orifice valve structure. A lowest temperature of 67.5 K was obtained at a frequency of 2.5 Hz under a system average pressure of 1.5 MPa with 200 mesh bronze screens as regenerator material, 80 mesh copper screens as stuffing material of heat exchanger. Due to the difficulty in manufacturing the thin "L" type pulse tube, the wall thickness of the pulse tube in the experiment was relatively difficult for us to reach 0.5 mm as that of the ordinary pulse tube, which resulted in relatively big system loss and affected the minimum temperature of the system to some degree.展开更多
The drop structure will fail as a result of local scoring downstream.This paper discusses the influence of a drop structures' upstream slope to local scour.Empirical equations of the scour hole were developed by l...The drop structure will fail as a result of local scoring downstream.This paper discusses the influence of a drop structures' upstream slope to local scour.Empirical equations of the scour hole were developed by laboratory experiment,theoretical assumptions,and regression analysis.These equations include the maximum scour depth and length during the scouring period,the maximum equilibrium scour depth and length,and the unit width scour rate.The four channel slopes(0%,2%,4%,and 6%) before the drop structure has been included in the analysis.A series of laboratory experiments were conducted to obtain 48 groups of experiments and 419 scour hole profiles during the scouring period.The material used in the scour section is uniform non-cohesive and with a median diameter of d50 = 0.5 mm.The results have been used to develop empirical equations via regression analysis to determine the coefficients of theoretical equations.The high correlation coefficient indicates that the equations developed in this study are suitable for verifying the characteristics of a scour hole at drop structure in the sloped channel.The semi-empirical equation is more accurate than the empirical equation.Compared to a horizontal channel,a sloped channel tends to cause a greater equilibriummaximum scour length,shorter equilibrium maximum scour depth,and faster unit-wide scour rate.展开更多
The latest sharp uplift of the Tibetan Plateau and adjacent mountains occurred at the end of the early Pleistocene. The uplift of the Plateau resulted from Late Mesozoic--Cenozoic compressional structure due to the su...The latest sharp uplift of the Tibetan Plateau and adjacent mountains occurred at the end of the early Pleistocene. The uplift of the Plateau resulted from Late Mesozoic--Cenozoic compressional structure due to the subduction of the Indian Plate beneath the Asian continent. This event definitively effected the formation of basin-mountain relief, Cenozoic basin deformation, large scale aridity and desertification of western China. The Australasian meteorites impact event happened ca. 0.8 Ma ago, located in the triangle area of the Indian Ocean ridge (20°S/67°E). The impact may have resulted in an acceleration of speeding of the Indian Ocean ridge pushing the Indian Plate to subduct rapidly northward. Thus, the impact event can give reasonable explanation for the dynamic background of the latest rapid uplift of the Tibetan Plateau and the continental deformation of western China and even of the Middle Asia.展开更多
Sutong Bridge is a cable-stayed bridge across Yangtze River with the main span of 1 088 m. This article outlines technical challenges,key technology and innovation in the design and construction such as scour protecti...Sutong Bridge is a cable-stayed bridge across Yangtze River with the main span of 1 088 m. This article outlines technical challenges,key technology and innovation in the design and construction such as scour protection,lowering steel cofferdam,construction platform establishment,construction and control of pylons,fabrication and damping of long cables,erection and control of steel box girders.展开更多
A theoretical model of phase change heat sink was established in terms of thermal resistance network. The influence of different parameters on the thermal resistance was analyzed and the crucial impact factors were de...A theoretical model of phase change heat sink was established in terms of thermal resistance network. The influence of different parameters on the thermal resistance was analyzed and the crucial impact factors were determined. Subsequently, the forming methods including ploughing-extrusion and stamping method of boiling enhancement structure at evaporation surface were investigated, upon which three-dimensional microgroove structure was fabricated to improve the efficiency of evaporation. Moreover, the crucial parameters related to the fabrication of miniaturized phase change heat sink were optimized. The heat transfer performance of the heat sink was tested. Results show that the developed phase change heat sink has excellent heat transfer performance and is suitable for high power LED applications.展开更多
Combined with the experimental results from the large tunnel of the ChongqingResearch Institute,the mechanism of gas and coal dust explosion was studied.Someconcepts about gas and coal dust explosion were introduced s...Combined with the experimental results from the large tunnel of the ChongqingResearch Institute,the mechanism of gas and coal dust explosion was studied.Someconcepts about gas and coal dust explosion were introduced such as the form conditionand influential factors.Gas and coal dust explosion propagation was researched and thelifting process of coal dust was simulated.When an explosion occurred due to great mixtureof gas and air,the maximum explosion pressure appeared in the neighborhood of theexplosion source point.Before it propagated to the tunnel of the deposited coal dust,themaximum explosion pressure appeared to be in declining trend.Part of the energy waslost in the process of raising the deposited coal dust through a shock wave,so the maximumexplosion pressure was smallest on the foreside of the deposited coal dust sector.On the deposited coal dust sector,the explosion pressure rapidly increased and droppedoff after achieving the largest peak value.Because of coal dust participation in the explosion,the flame velocity rose rapidly on the deposited coal dust and achieved a basic stablevalue;coal dust was ignited to explode by initial laminar flame,and the laminar flametransformed into turbulent flame.The turbulence transformed the flame fold into a funnelshape and the shock wave interacted with the flame,so the combustion rate rose and thepressure wave was further enhanced.The regeneration mechanism between the flamecombustion rate and the aerodynamic flowing structure achieved the final critical state forforming the detonation.展开更多
A path-based timing optimization algorithm for buffer insertion and simultaneous sizing is proposed. Firstly, candidate buffer insertion location and buffer size for each branch in a given routing path were obtained v...A path-based timing optimization algorithm for buffer insertion and simultaneous sizing is proposed. Firstly, candidate buffer insertion location and buffer size for each branch in a given routing path were obtained via localized timing optimization. Then, through evaluating each potential insertion against design objectives, potential optimal buffer insertion locations and sizes for the whole routing tree were determined. At last, by removing redundant buffer insertion operations which do not maximize S （ so ）, given timing requirements are finally fulfilled through minimum number of buffers.展开更多
文摘The single event transient effects of the operational amplifier LM124J and the optocoupler HCPL 5231 are investigated by a pulsed laser test facility. The relation of transient pulse shape to pulsed laser equivalent LET is tested,the sensitive areas of the SET effects are identified in voltage follower application mode of LM124J, and the mechanism is initially analyzed. The transient amplitude and duration of HCPL5231 at various equivalent LET are examined,and the SET cross-section is measured. The results of our test and heavy ion experimental data coincide closely,indicating that a pulsed laser test facility is a valid tool for single event effect evaluation.
基金financially supported by the key Projects of the Chinese Academy of Sciences (Grant No.KZZD-EW-05-01-04)the National Science and Technology Support Program (Grant No.2012BAC06B02)the sub-program of Science and technology research and development plan from China Railway (Grant No.2014G004-A-5)
文摘Drainage canals are engineering structures widely used for debris flow mitigation.When passing through a drainage canal,debris flow usually scours the gully bed at the back of the rib sill of the drainage canal,which leads to failure of the rib sill.Therefore,the scour depth at the back of the rib sill is an important design problem and it is related to the economic benefits of engineering and service years.To explore the law of the depth of the scour pit after debris flow through drainage canal ribs,we first proposed a formula for the calculation of the maximum scour depth at the back of a rib sill based on energy conservation.We then conducted a series of simulation experiments to test the proposed formula.The experimental results show that the scour depth,trench slope and the distance between ribs all increase with a decrease in debris flow density.We then compared the results of experiments and formula calculations.Through the testing analysis,we found that the calculation results of the conductedformula correspond with the experimental results better.Finally,taking Qipan Gully as an example,we designed the ultimate depth of a drainage canal for debris flow using the calculation formula.
文摘The dynamic performance and the stability are essential for a system. A new circuit topology used for electrical discharge machining (EDM) power and made up of complex-pulse (voltage-pulse and current-pulse) is presented. The large-signal model of it is also derived. Based on the comprehensive analysis of the system model, the compensator is designed to make the system match better and to improve its dynamic performance and the stability under perturbations. Finally, the design methods and the analysis are verified by simulation and experimental results.
文摘Titanium nitride thin films were deposited on silicon by high power impulse magnetron sputtering(HiPIMS)method at different frequencies(162-637 Hz)and pulse-on time(60-322μs).Response surface methodology(RSM)was employed to study the simultaneous effect of frequency and pulse-on time on the current waveforms and the crystallographic orientation,microstructure,and in particular,the deposition rate of titanium nitride at constant time and average power equal to 250 W.The crystallographic structure and morphology of deposited films were analyzed using XRD and FESEM,respectively.It is found that the deposition rate of HiPIMS samples is tremendously dependent on pulse-on time and frequency of pulses where the deposition rate changes from 4.5 to 14.5 nm/min.The regression equations and analyses of variance(ANOVA)reveal that the maximum deposition rate(equal to(17±0.8)nm/min)occurs when the frequency is 537 Hz and pulse-on time is 212μs.The experimental measurement of the deposition rate under this condition gives rise to the deposition rate of 16.7 nm/min that is in good agreement with the predicted value.
文摘A method of improving the accuracy of laser pulse range finding from ±10 m to ±1 m inexpensively by means of time scale up is described. Time scale up can stretch the entire flight time by a factor of 1 000 and then the stretched result is counted to calculate the distance. The use of this technique decreases the resolution of counting from nanosecond to microsecond, therefore a separate counting oscillator followed by an interpolation operation is unnecessary. This technique can improve the accuracy of laser pulse range finding inexpensively and effectively.
基金the National Natural Science Foundation of China (Nos. 40901007, 50979103)
文摘The erosion shape and the law of development of debris flow sabo dam downstream is a weak part in the study on debris flow erosion. The shape and development of scour pit have an important effect on the stability and safety of debris flow sabo dam, which determines the foundational depth of the dam and the design of protective measures downstream. Study on the scouring law of sabo dam downstream can evaluate the erosion range and reasonably arrange auxiliary protective engineering. Therefore, a series of flume experiments are carried out including different debris flow characteristics （density is varying from 1.5 t/m3 to 2.1 t/m~） and different gully longitudinal slopes. The result shows that the scour pit appears as an oval shape in a plane and deep in the middle while superficial at the ends in the longitudinal section, the position of the maximum depth point moves towards downstream with an increase of flume slope angle. The maximum depth of scour pit is mainly affected by the longitudinal slope of gully, density of debris flow, and the characteristics of gully composition （particle size and the viscosity of soil）. The result also indicates that the viscosity of soil will weaken the erosion extent. The interior slopes of scour pit are different between the upstream and the downstream, and the downstream slope is smaller than the upper one. For the viscous and non-viscous sands with the same distribution of gradation, the interior slope of non- viscous sand is smaller than the viscous sand.According to tbe regression analysis on the experimental data, the quantitative relationship between the interior slope of scour pit, slope of repose under water and the longitudinal slope of gully is established and it can be used to calculate the interior slope of scour pit. The results can provide the basis for the parameter design of the debris flow control engineering foundation.
基金Project(2011-0006548) supported by the Basic Science Research Program through the National Research Foundation of Korea(NRF) funded by the Ministry of Education,Science,and Technology,Korea
文摘Impact property of the sandwich composite with aluminum foam core was investigated by experiment and simulation analysis. Impact energies of 50, 70 and 100 J were applied to the specimens in impact tests. The results show that the striker penetrates the upper face sheet, causing the core to be damaged at 50 J test but the lower face sheet remains intact with no damage. At 70 J test, the striker penetrates the upper face sheet and the core,and causes the lower face sheet to be damaged. Finally at 100 J test, the striker penetrates both the upper face sheet and the core, and even the lower face sheet. The experimental and simulation results agree with each other. By the confirmation with the experimental results, all these simulation results can be applied on structure study of real sandwich composite with aluminum foam core effectively.
文摘Bridge pressure flow scour at clear water threshold condition is studied theoretically and experimentally.The flume experiments reveal that the measured scour profiles under a bridge are more or less 2-dimensional;all the measured scour profiles can be described by two similarity equations,where the horizontal distance is scaled by the deck width while the local scour by the maximum scour depth;the maximum scour position is located just under the bridge about 15% deck width from the downstream deck edge;the scour begins at about one deck width upstream the bridge while the deposition occurs at about 2.5 deck widths downstream the bridge;and the maximum scour depth decreases with increas-ing sediment size,but increases with deck inundation.The theoretical analysis shows that:bridge scour can be divided into three cases,i.e.downstream unsubmerged,partially submerged,and totally submerged.For downstream unsubmerged flows,the maximum bridge scour depth is an open-channel problem where the conventional methods in terms of critical velocity or bed shear stress can be applied;for partially and totally submerged flows,the equilibrium maximum scour depth can be described by a scour and an inundation similarity number,which has been confirmed by experiments with two decks and two sediment sizes.For application,a design and field evaluation procedure with examples is presented,including the maximum scour depth and scour profile.
基金National Natural Science Foundation of China(60507001 60477022 06YFGPGX08500)
文摘Proposed is a novel optical pulse compression technique based on high-doped erbium fiber amplifier and standard single-mode fiber(SMF). We used the amplifier with the erbium ion concentration of 6.3×10-3 to amplify a hyperbolic secant pulse from a regeneratively mode-locked fiber laser. The central wavelength, pulsewidth and peak power of the pulse are 1 550 nm, 12.5 ps and 3 mW, respectively. Then the amplified pulse with peak power level corresponding to a higher-order soliton is compressed when it propagates through a 3-km-long single-mode fiber. Studied are the compressed pulses under different pump powers and fiber lengths. The results show that it can get a narrower pulse, and solve the difficulty that pulses at low power can not be compressed directly in the fiber. And the construct is compact.
基金Project(2019SDZY02)supported by the Major Scientific and Technological Innovation Project of Shandong Provincial Key Research Development Program,ChinaProject(51904165)supported by the National Natural Science Foundation of ChinaProject(ZR2019QEE026)supported by the Shandong Provincial Natural Science Foundation,China。
文摘To research the anchoring effect of large deformation bolt,tensile and drawing models are established.Then,the evolution laws of drawing force,bolt axial force and interfacial shear stress are analyzed.Additionally,the influence of structure element position on the anchoring effect of large deformation bolt is discussed.At last,the energy-absorbing support mechanism is discussed.Results show that during the drawing process of normal bolt,drawing force,bolt axial force and interfacial shear stress all gradually increase as increasing the drawing displacement,but when the large deformation bolt enters the structural deformation stage,these three values will keep stable;when the structure element of large deformation bolt approaches the drawing end,the fluctuation range of drawing force decreases,the distributions of bolt axial force and interfacial shear stress of anchorage section are steady and the increasing rate of interfacial shear stress decreases,which are advantageous for keeping the stress stability of the anchorage body.During the working process of large deformation bolt,the strain of bolt body is small,the working resistance is stable and the distributions of bolt axial force and interfacial shear stress are steady.When a rock burst event occurs,the bolt and bonding interface cannot easily break,which weakens the dynamic disaster degree.
基金Supported by National Natural Science Foundation of China under Grant Nos 60672004 and 60877057, and the National High-Tech Research and Development Program of China under Grant No 2007AA01Z270.
文摘We establish an equivalent cascaded semiconductor optical amplifier system model to analyze the characteristics of the double loop optical buffer （DLOB）. The theoretical analysis finds that the performance of the DLOB can be improved by inserted amplifying process in an interval of some cycles. The experiment demonstrates that the buffered cycles can be improved from 20 to 50 and the bit error rate is less than 10-9 by inserting amplifying process in an interval of about 10 cycles.
基金The authors are grateful for the financial supports from the Key Research and Development Program of Guangdong Province,China(2020B090928003)the Natural Science Foundation of Guangdong Province,China(2020A1515011050)+1 种基金the Science and Technology Base and Talent Special Project of Guangxi Province,China(AD19245150)Guangxi University of Science and Technology Doctoral Fund,China(19Z27).
文摘The 12 mm-thick Ti−6Al−4V(TC4)titanium alloy plates were welded using keyhole tungsten inert gas(K-TIG)welding at various heat inputs.The microstructure,grain boundary(GB)characteristics and mechanical properties of the weld metal zone(WMZ)were analyzed.The test results show that the K-TIG welds are well formed,and no obvious defects are observed when the heat input is 2.30−2.62 kJ/mm.When the heat input gradually increases,αlaths increase in length,andα′phase and residualβphase are reduced.The electron backscatter diffraction(EBSD)test results indicate that the high-angle GB proportion in the WMZ increases with the increase of heat input.The tensile strength of the WMZ gradually decreases and the elongation of the WMZ increases when the heat input increases from 2.30 to 2.62 kJ/mm.The impact toughness of the WMZ increases as the heat input increases.
文摘Isotopic tracers and water quality indicators （TDS （Total Dissolved Solid）, Cl^- and NO3^-contents） were used to characterize the recharge and control of the quality of groundwater in the alluvial aquifer beneath of the N＇djamena city. For this study, a total of 92 waters samples were taken and this included 67 wells, 21 pumps and 4 surface waters. Some groundwater has 6180 and 62H values close to those of the city of N＇djamena and/or the Chad river rains. However, all sampled points are below the Global Meteoric Water Line reflecting their evaporated characters. The interpretation of the isotopic tracers highlights that the recharge of the analyzed ground waters may result from two major mechanisms： （1） direct infiltration of local precipitation; （2） lateral inflow of river waters. The upper aquifer is the most vulnerable to pollution, especially during the recharge period. This pollution is due to the leaching of soils during the rainy season and the rise of the groundwater level which accompanies the overflowing of the Chad and causes the leaching of the polluted horizons of the unsaturated zone. In contrast, the lower aquifer has acceptable concentrations of solutes.
文摘In order to simplify the structure of the cold end of the pulse tube refrigerator (PTR) and have a better utilization of the cold energy of the system, a one-stage four-valve pulse tube refrigerator (FVPTR) with an "L" type pulse tube structure and two orifice valves at the hot end of pulse tube has been constructed. Verification experiments show that the two orifice valve structure performs better than one orifice valve structure. A lowest temperature of 67.5 K was obtained at a frequency of 2.5 Hz under a system average pressure of 1.5 MPa with 200 mesh bronze screens as regenerator material, 80 mesh copper screens as stuffing material of heat exchanger. Due to the difficulty in manufacturing the thin "L" type pulse tube, the wall thickness of the pulse tube in the experiment was relatively difficult for us to reach 0.5 mm as that of the ordinary pulse tube, which resulted in relatively big system loss and affected the minimum temperature of the system to some degree.
基金the research support from Ministry of Science and Technology of Chinese Taipei,with the project no.104-2313-B-343-001
文摘The drop structure will fail as a result of local scoring downstream.This paper discusses the influence of a drop structures' upstream slope to local scour.Empirical equations of the scour hole were developed by laboratory experiment,theoretical assumptions,and regression analysis.These equations include the maximum scour depth and length during the scouring period,the maximum equilibrium scour depth and length,and the unit width scour rate.The four channel slopes(0%,2%,4%,and 6%) before the drop structure has been included in the analysis.A series of laboratory experiments were conducted to obtain 48 groups of experiments and 419 scour hole profiles during the scouring period.The material used in the scour section is uniform non-cohesive and with a median diameter of d50 = 0.5 mm.The results have been used to develop empirical equations via regression analysis to determine the coefficients of theoretical equations.The high correlation coefficient indicates that the equations developed in this study are suitable for verifying the characteristics of a scour hole at drop structure in the sloped channel.The semi-empirical equation is more accurate than the empirical equation.Compared to a horizontal channel,a sloped channel tends to cause a greater equilibriummaximum scour length,shorter equilibrium maximum scour depth,and faster unit-wide scour rate.
基金Supported by Projects of NSFC (Nos. 40872127, 40572135)
文摘The latest sharp uplift of the Tibetan Plateau and adjacent mountains occurred at the end of the early Pleistocene. The uplift of the Plateau resulted from Late Mesozoic--Cenozoic compressional structure due to the subduction of the Indian Plate beneath the Asian continent. This event definitively effected the formation of basin-mountain relief, Cenozoic basin deformation, large scale aridity and desertification of western China. The Australasian meteorites impact event happened ca. 0.8 Ma ago, located in the triangle area of the Indian Ocean ridge (20°S/67°E). The impact may have resulted in an acceleration of speeding of the Indian Ocean ridge pushing the Indian Plate to subduct rapidly northward. Thus, the impact event can give reasonable explanation for the dynamic background of the latest rapid uplift of the Tibetan Plateau and the continental deformation of western China and even of the Middle Asia.
文摘Sutong Bridge is a cable-stayed bridge across Yangtze River with the main span of 1 088 m. This article outlines technical challenges,key technology and innovation in the design and construction such as scour protection,lowering steel cofferdam,construction platform establishment,construction and control of pylons,fabrication and damping of long cables,erection and control of steel box girders.
基金Projects(51575115,51775122) supported by the National Natural Science Foundation of China
文摘A theoretical model of phase change heat sink was established in terms of thermal resistance network. The influence of different parameters on the thermal resistance was analyzed and the crucial impact factors were determined. Subsequently, the forming methods including ploughing-extrusion and stamping method of boiling enhancement structure at evaporation surface were investigated, upon which three-dimensional microgroove structure was fabricated to improve the efficiency of evaporation. Moreover, the crucial parameters related to the fabrication of miniaturized phase change heat sink were optimized. The heat transfer performance of the heat sink was tested. Results show that the developed phase change heat sink has excellent heat transfer performance and is suitable for high power LED applications.
基金Supported by the National Basic Research Program(973)(2005CB221506)National Natural Science Foundation of Chongqing(CSTC,2007BA6018)National Key Technology R&D Program(2006ABK03B04)
文摘Combined with the experimental results from the large tunnel of the ChongqingResearch Institute,the mechanism of gas and coal dust explosion was studied.Someconcepts about gas and coal dust explosion were introduced such as the form conditionand influential factors.Gas and coal dust explosion propagation was researched and thelifting process of coal dust was simulated.When an explosion occurred due to great mixtureof gas and air,the maximum explosion pressure appeared in the neighborhood of theexplosion source point.Before it propagated to the tunnel of the deposited coal dust,themaximum explosion pressure appeared to be in declining trend.Part of the energy waslost in the process of raising the deposited coal dust through a shock wave,so the maximumexplosion pressure was smallest on the foreside of the deposited coal dust sector.On the deposited coal dust sector,the explosion pressure rapidly increased and droppedoff after achieving the largest peak value.Because of coal dust participation in the explosion,the flame velocity rose rapidly on the deposited coal dust and achieved a basic stablevalue;coal dust was ignited to explode by initial laminar flame,and the laminar flametransformed into turbulent flame.The turbulence transformed the flame fold into a funnelshape and the shock wave interacted with the flame,so the combustion rate rose and thepressure wave was further enhanced.The regeneration mechanism between the flamecombustion rate and the aerodynamic flowing structure achieved the final critical state forforming the detonation.
文摘A path-based timing optimization algorithm for buffer insertion and simultaneous sizing is proposed. Firstly, candidate buffer insertion location and buffer size for each branch in a given routing path were obtained via localized timing optimization. Then, through evaluating each potential insertion against design objectives, potential optimal buffer insertion locations and sizes for the whole routing tree were determined. At last, by removing redundant buffer insertion operations which do not maximize S （ so ）, given timing requirements are finally fulfilled through minimum number of buffers.
