The reverse transformation temperature and recovery strain ratio of the martensite formed during the cooling process under a constant stress in TiNi shape memory alloy wires are studied in this paper. Results sh...The reverse transformation temperature and recovery strain ratio of the martensite formed during the cooling process under a constant stress in TiNi shape memory alloy wires are studied in this paper. Results show that a higher level of the applied constant stress during the cooling process will induce martensite with a higher reverse martensitic transformation start temperature As and a smaller recovery strain ratio. Similarly, a prestrain at the room temperature elevates the As temperature and decreases the recovery strain ratio. However, the As temperature and the recovery strain ratio of the martensite formed during the cooling process under a constant stress are lower than those of the martensite formed by prestrain at the room temperature.展开更多
DSC was used to study the effects of predeformation on the reverse martensitic transformation of near-equiatomic TiNi alloy. Both the start temperature As and the finish temperature Af of the reverse transformation in...DSC was used to study the effects of predeformation on the reverse martensitic transformation of near-equiatomic TiNi alloy. Both the start temperature As and the finish temperature Af of the reverse transformation increased with increasing degree of predeformation, but the algebraic difference between As and Af decreased with increasing predeformation until it reached a minimum value, then remained unchanged with further deformation. Transformation heat also increased with increasing predeformation until it reached a maximum value, then decreased with further predeformation. All the phenomena above were considered to be closely related with the release of elastic strain energy during predeformation.展开更多
Internal friction （IF） spectra during reverse martensitic transformation from 35 to 135°C at different temperature rates of 0.5,0.75,and 1°C/min for Ti50Ni27Cu23 shape memory alloy （SMA） samples were mea...Internal friction （IF） spectra during reverse martensitic transformation from 35 to 135°C at different temperature rates of 0.5,0.75,and 1°C/min for Ti50Ni27Cu23 shape memory alloy （SMA） samples were measured with a dynamic mechanical analyzer,respectively.The IF spectra were characterized by IF peak increasing progressively and peak shifting toward high temperature with an increase in temperature rate.An iterative approach was used to calculate the precise intrinsic and approximate transitory IF contributions to the normal IF spectrum.The quantitatively analyzed results indicate that the transitory IF of this alloy is nonlinearly dependent on the temperature rate and obeys a power law with a power coefficient of 0.55.The predicted and experimental IF spectra at different temperature rates of 0.75 and 1°C/min agree well with each other,respectively.展开更多
The reverse martensitic transformation of TiNi alloy wires prestrained in the parent phase was studied. Experimental results shou, that the reverse transformation of the TiNi allogys prestrained in the parent phase is...The reverse martensitic transformation of TiNi alloy wires prestrained in the parent phase was studied. Experimental results shou, that the reverse transformation of the TiNi allogys prestrained in the parent phase is significantly different from that of the TiNi alloys prestrained in the martensite phase. Three continual peaks appear on the DSC curves of wires with a small prestrain and one high temperature peak appears on the DSC curves of wires with a large prestrain.展开更多
Phase transformation from austenite to martensite in NiTi alloy strips under the uniaxial tension has been observed in experiments and numerically simulated as a localized deformation. This work presents an analysis u...Phase transformation from austenite to martensite in NiTi alloy strips under the uniaxial tension has been observed in experiments and numerically simulated as a localized deformation. This work presents an analysis using the theory of phase transformation. The jump of deformation gradient across the interface between two phases and the Maxwell relation are considered. Governing equations for the phase transformation are derived. The analysis is reduced to finding the minimum value of the loading at which the governing equations have a unique, real and physically acceptable solution. The equations are solved numerically and it is verified that the unique solution exists definitely. The Maxwell stress, the stresses and strains inside both austenite and martensite phases, and the transformation-front orientation angle are determined to be in reasonably good agreement with experimental observations.展开更多
The actuation mechanism of TiNi shape memory alloy wires, which were deformed at parent phase followed by a cooling process under constant strain constraint, was investigated. The experimental results show that the tw...The actuation mechanism of TiNi shape memory alloy wires, which were deformed at parent phase followed by a cooling process under constant strain constraint, was investigated. The experimental results show that the two-step reverse martensitic transformation behavior occurs during the heating process, and the temperature range of reverse transformation was obviously widened with the increasing of prestrain. The recovery strain vs temperature curves exhibits an actuation characteristic of linear output recovery strain in a wide temperature range.展开更多
The effect of age hardening on the microstructure,martensitic transformation behavior,and shape memory properties of the(Ni_(50)Ti_(30)Hf_(20))_(95)V_(5)alloy was investigated by scanning electron microscopy,transmiss...The effect of age hardening on the microstructure,martensitic transformation behavior,and shape memory properties of the(Ni_(50)Ti_(30)Hf_(20))_(95)V_(5)alloy was investigated by scanning electron microscopy,transmission electron microscopy,X-ray diffraction,differential scanning calorimetry,microhardness,and bending tests.The results demonstrate a significant influence of V addition on the microstructure of the alloy.V addition leads to the formation of a(Ni,V)_(2)(Ti,Hf)-type Laves phase,which coexists with B19'martensite at room temperature.Aging at 550℃results in precipitation hardening due to the formation of nano-scale orthorhombic H-phase,with the peak hardness observed after 3 h of aging.The alloy at peak hardness state exhibits higher transformation strain and lower unrecovered strain compared to the solution-treated sample.The aged sample achieves a maximum transformation strain of 1.56%under 500 MPa.展开更多
Strain-induced martensitic phase transformation and its influence on the forrnability of newly developed nitrogen-alloyed metastable austenitic stainless steels were systematically investigated. Yield strength for the...Strain-induced martensitic phase transformation and its influence on the forrnability of newly developed nitrogen-alloyed metastable austenitic stainless steels were systematically investigated. Yield strength for the as- received steels bearing low nickel content was around 300 MPa and their elongation ratios varied from 55.2% to 61.7%. Erichsen numbers of these samples differed from 13.82 to 14.57 mm. Although its Cu content was lower than that of other samples, steel D2 exhibited better plasticity and formability, which was attributed to ~/--,c~＇ martensitic phase transformation. EBSD, XRD, and magnetism tests showed that increases in deformation ratio gradually increased the α＇ martensite phase of a sample ,thereby contributing to its strain and inducing the optimal transformation-induced plasticity effect. An Meeo/5o temperature of around 20 ℃, which is close to the deformation temperature,provided the austenite with adequate stability and gradually transformed it into martensite, thereby endowing lean ASS with better formability.展开更多
To control the reverse-transformation austenite structure through manipulation of the micro/nanometer grain structure, the influences of cold deformation and annealing parameters on the microstructure evolution and me...To control the reverse-transformation austenite structure through manipulation of the micro/nanometer grain structure, the influences of cold deformation and annealing parameters on the microstructure evolution and mechanical properties of 316L austenitic stainless steel were investigated. The samples were first cold-rolled, and then samples deformed to different extents were annealed at different temperatures. The microstructure evolutions were analyzed by optical microscopy, scanning electron microscopy (SEM), magnetic measurements, and X-ray diffraction (XRD); the mechanical properties are also determined by tensile tests. The results showed that the fraction of stain-induced martensite was approximately 72% in the 90% cold-rolled steel. The micro/nanometric microstructure was obtained after reversion annealing at 820-870A degrees C for 60 s. Nearly 100% reversed austenite was obtained in samples annealed at 850A degrees C, where grains with a diameter ae<currency> 500 nm accounted for 30% and those with a diameter > 0.5 mu m accounted for 70%. The micro/nanometer-grain steel exhibited not only a high strength level (approximately 959 MPa) but also a desirable elongation of approximately 45%.展开更多
Grinding-induced tm phase transformation and the resultant texture in ceria-yttria-doped tetragonal zirconia polycrystals with varied tetragonality have been studied by XRD. It is observed that the reversible tm phase...Grinding-induced tm phase transformation and the resultant texture in ceria-yttria-doped tetragonal zirconia polycrystals with varied tetragonality have been studied by XRD. It is observed that the reversible tm phase transformation occurs during grinding and the intensity ratio of I(002)t/I(200)t increases with the transformability. The author proposes that the texture induced by grinding at low temperatures is due to the tetragonal variant reorientation via cyclic,reversible tm phase transformation, termed 'transformational domain switching', instead of the ferroelastic one展开更多
Heat treatment of Ti-50.9%Ni （mole fraction） alloy was studied by differential scanning calorimetry, X-ray diffraction, scanning electron microscopey and energy dispersive X-ray analysis to investigate the influence...Heat treatment of Ti-50.9%Ni （mole fraction） alloy was studied by differential scanning calorimetry, X-ray diffraction, scanning electron microscopey and energy dispersive X-ray analysis to investigate the influence of cooling rate on transformation behavior and microstructures of NiTi shape memory alloy. The experimental results show that three-stage phase transformation can be induced at a very low cooling rate such as cooling in furnace. The cooling rate also has a great influence on the phase transformation temperatures. Both martensitic start transformation temperature （Ms） and martensitic finish transformation temperature （Mf） decrease with the decrease of the cooling rate, and decreasing the cooling rate contributes to enhancing the M→A austenite transformation temperature. The phase transformation hysteresis （Af-Mf） increases with the decrease of the cooling rate. Heat treatment is unable to eliminate the textures formed in hot working of NiTi sample, but can weaken the intensity of them. The cooling rate has little influence on the grain size.展开更多
The kinetics of the reversible martensitic transformation in a Cu-Zn-Al-Mn-Ni shape memory alloy has been studied by means of differential scanning calorimetry.The apparent activation energy has been calculated and th...The kinetics of the reversible martensitic transformation in a Cu-Zn-Al-Mn-Ni shape memory alloy has been studied by means of differential scanning calorimetry.The apparent activation energy has been calculated and the kinetic equations of positive and adverse martensitic transformation have been established with the variations of temperature and time.展开更多
This paper studies the martensitic transformation in the Cu-doped NiMnGa alloys. The orthorhombic martensite transforms to L21 cubic austenite by Cu substituting for Ni in the Nis0-xCuxMn31Ga19 （x=2 10） alloys, the ...This paper studies the martensitic transformation in the Cu-doped NiMnGa alloys. The orthorhombic martensite transforms to L21 cubic austenite by Cu substituting for Ni in the Nis0-xCuxMn31Ga19 （x=2 10） alloys, the martensitic transformation temperature decreases significantly with the rate of 40 K per Cu atom addition. The variation of the Fermi sphere radius （kF） is applied to evaluate the change of the martensitic transformation temperature. The increase of kF leads to the increase of the martensitic transformation temperature.展开更多
The effects of small amount additions of Sm on the martensitic transition and magnetic phase transition of polycrystalline Ni-Mn-Ga alloys were investigated. The experimental results show that the Sm doped alloys also...The effects of small amount additions of Sm on the martensitic transition and magnetic phase transition of polycrystalline Ni-Mn-Ga alloys were investigated. The experimental results show that the Sm doped alloys also undergo a thermal-elastic martensitic transformation and reverse transformation during cooling and heating process and the addition of Sm decreases the martensitic transformation temperature and Curie temperature in different degree respectively. Ni-Mn-Ga alloys of adding Sm still possess Heusler structure, but their crystal lattice parameters are modified slightly. The addition of a proper amount of Sm does not basically decrease T_c of the alloy when avoiding the appearance of second phase. In addition, the doped alloys have favorable toughness because of grain refinement of Sm.展开更多
The hyperfine interactions of two shape memory alloys have been studied by Mossbauer effect measurement at various temperatures. The Mossbauer spectra exhibit a mag-netic change from antiferro magnetic state to parama...The hyperfine interactions of two shape memory alloys have been studied by Mossbauer effect measurement at various temperatures. The Mossbauer spectra exhibit a mag-netic change from antiferro magnetic state to paramagnetic state when the temperuture rises. The Fe-Mn-Si alloys have a small hyperfine field and silicon element increases the hyperfine field and magnetic susceptibility. Thermo-induced γ→ ε trunsforma-tions are suppressed by Neel transition and by increasing carbon content, whereas stress induced γ→ ε transformation occurs in both alloys. Antiferromagnetic spin order can suppress thermo-induced γ→εtransformations efficiently, but cannot sup-press stress induced γ → ε transformation.展开更多
Measurements of electrical resistivity, X-ray diffraction, and tensile test at room temperature and ？196°C were performed to investigate the effects of Al addition substituting Ni on the phase transformation beh...Measurements of electrical resistivity, X-ray diffraction, and tensile test at room temperature and ？196°C were performed to investigate the effects of Al addition substituting Ni on the phase transformation behaviors, the mechanical properties, and the shape memory effects of Ti50Ni47Fe2Al1 and Ti50Ni46.5Fe2.5Al1 alloys. It is found that 1at% Al addition dramatically decreases the martensitic start transformation temperature and expands the transformation temperature range of R-phase for TiNiFeAl alloys. The results of tensile test indicate that 1at% Al improves the yield strength of Ti50Ni47Fe2Al1 and Ti50Ni46.5Fe2.5Al1 alloys by 40% and 64%, but de- creases the plasticity to 11% and 12% from 26% and 27% respectively. Moreover, excellent shape memory effect of 6.6% and 7.5% were found in Ti50Ni47Fe2Al1 and Ti50Ni46.5Fe2.5Al1 alloys, which results from the stress-induced martensite transformation from the R-phase.展开更多
The microstructural features, shape memory behavior and mechanical properties of Ni-Mn based alloys were investigated by differential scanning calorimetry （DSC）, scanning electron microscopy （SEM）, transmission el...The microstructural features, shape memory behavior and mechanical properties of Ni-Mn based alloys were investigated by differential scanning calorimetry （DSC）, scanning electron microscopy （SEM）, transmission electron microscopy （TEM） and thermal cycling test under various stresses. The transformation temperatures shifted toward lower temperatures when adding a third element into the Ni-Mn system. The addition of 10 at. pct Fe increased considerably the mechanical properties exhibiting still high transformation temperatures. However, it was found that in NiMn40Fe10 alloy the martensitic transformation is not thermoelastic in nature. The mechanism of this transformation and the crystallography of Ni-Mn（50-x）-Fex （x=5, 7, 10, 20 at. pct） alloys are presented.展开更多
The present research aimed to analyze the influence that different contents of titanium(x=0.5,0.6 and 0.7 wt.%)have on the martensitic transformation temperature of a Cu-14Al-4Ni(wt.%)SMA(shape memory alloy).The Cu-14...The present research aimed to analyze the influence that different contents of titanium(x=0.5,0.6 and 0.7 wt.%)have on the martensitic transformation temperature of a Cu-14Al-4Ni(wt.%)SMA(shape memory alloy).The Cu-14Al-4Ni-xTi samples were casted in an arc-melting furnace and rapidly solidified.All samples underwent heat treatment in a tubular furnace at a temperature of 1,100°C for 30 min and water quenched at 25°C.Subsequently,samples were analyzed by SEM(scanning electron microscopy)with EDS(energy dispersive spectroscopy),XRD(X-ray diffraction)and DSC(differential scanning calorimeter).SEM images and XRD patterns showed that the presence of titanium modified the alloy’s microstructure,induced the formation of three titanium rich phases called“X”phase(CuNi2Ti,Cu3Ti and AlCu2Ti)and reduced the presence of the brittle phaseγ2(Cu9Al4)for samples with 0.6 and 0.7 wt.%Ti.The titanium added to the copper based SMA also functioned as a refiner,reducing GS(grain size)up to approximately 80%with the increase of Ti content.DSC results exhibited low enthalpy levels,hysteresis,as well as low start martensitic transformation temperatures.展开更多
The effect of deformation via stress-induced martensitic transformation on the reverse transformation behavior of the (Ni47Ti44)100?xNbx (x=3, 9, 15, 20, 30, mole fraction, %) shape memory alloys was investigated in d...The effect of deformation via stress-induced martensitic transformation on the reverse transformation behavior of the (Ni47Ti44)100?xNbx (x=3, 9, 15, 20, 30, mole fraction, %) shape memory alloys was investigated in detail by differential scanning calorimetry (DSC) after performing cryogenic tensile tests at a temperature of Ms+30 ℃. The results show that Nb-content has obvious effect on the process of stress-induced martensitic transformation. It is also observed that the stress-induced martensite is stabilized relative to the thermally-induced martensite (TIM) formed on cooling, and Nb-content in Ni-Ti-Nb alloy has great influence on the reverse transformation start temperature and transformation temperature hysteresis of stress-induced martensite(SIM). The mechanism of wide transformation temperature hysteresis was fully explained based on the microscopic structure and the distribution of the elastic strain energy of (Ni47Ti44)100?xNbx alloys.展开更多
基金supported by the National Natural Science Foundation of the People’s Republic of China under grant No.50071037.
文摘The reverse transformation temperature and recovery strain ratio of the martensite formed during the cooling process under a constant stress in TiNi shape memory alloy wires are studied in this paper. Results show that a higher level of the applied constant stress during the cooling process will induce martensite with a higher reverse martensitic transformation start temperature As and a smaller recovery strain ratio. Similarly, a prestrain at the room temperature elevates the As temperature and decreases the recovery strain ratio. However, the As temperature and the recovery strain ratio of the martensite formed during the cooling process under a constant stress are lower than those of the martensite formed by prestrain at the room temperature.
基金the National Natural Science Foundation of China under grant No. 59601004,59731030.
文摘DSC was used to study the effects of predeformation on the reverse martensitic transformation of near-equiatomic TiNi alloy. Both the start temperature As and the finish temperature Af of the reverse transformation increased with increasing degree of predeformation, but the algebraic difference between As and Af decreased with increasing predeformation until it reached a minimum value, then remained unchanged with further deformation. Transformation heat also increased with increasing predeformation until it reached a maximum value, then decreased with further predeformation. All the phenomena above were considered to be closely related with the release of elastic strain energy during predeformation.
文摘Internal friction （IF） spectra during reverse martensitic transformation from 35 to 135°C at different temperature rates of 0.5,0.75,and 1°C/min for Ti50Ni27Cu23 shape memory alloy （SMA） samples were measured with a dynamic mechanical analyzer,respectively.The IF spectra were characterized by IF peak increasing progressively and peak shifting toward high temperature with an increase in temperature rate.An iterative approach was used to calculate the precise intrinsic and approximate transitory IF contributions to the normal IF spectrum.The quantitatively analyzed results indicate that the transitory IF of this alloy is nonlinearly dependent on the temperature rate and obeys a power law with a power coefficient of 0.55.The predicted and experimental IF spectra at different temperature rates of 0.75 and 1°C/min agree well with each other,respectively.
基金Funded by the National Natural Science Foundation of China(No.50071037)
文摘The reverse martensitic transformation of TiNi alloy wires prestrained in the parent phase was studied. Experimental results shou, that the reverse transformation of the TiNi allogys prestrained in the parent phase is significantly different from that of the TiNi alloys prestrained in the martensite phase. Three continual peaks appear on the DSC curves of wires with a small prestrain and one high temperature peak appears on the DSC curves of wires with a large prestrain.
基金the National Natural Science Foundation of China(No.10272079)the joint grant from the National Natural Science Foundation of China and the Royal Society
文摘Phase transformation from austenite to martensite in NiTi alloy strips under the uniaxial tension has been observed in experiments and numerically simulated as a localized deformation. This work presents an analysis using the theory of phase transformation. The jump of deformation gradient across the interface between two phases and the Maxwell relation are considered. Governing equations for the phase transformation are derived. The analysis is reduced to finding the minimum value of the loading at which the governing equations have a unique, real and physically acceptable solution. The equations are solved numerically and it is verified that the unique solution exists definitely. The Maxwell stress, the stresses and strains inside both austenite and martensite phases, and the transformation-front orientation angle are determined to be in reasonably good agreement with experimental observations.
基金FundedbytheNationalNaturalScienceFoundationofChi na (No .5 0 0 710 37)
文摘The actuation mechanism of TiNi shape memory alloy wires, which were deformed at parent phase followed by a cooling process under constant strain constraint, was investigated. The experimental results show that the two-step reverse martensitic transformation behavior occurs during the heating process, and the temperature range of reverse transformation was obviously widened with the increasing of prestrain. The recovery strain vs temperature curves exhibits an actuation characteristic of linear output recovery strain in a wide temperature range.
基金supported by the National Natural Science Foundation of China(Nos.52201207,52271169)。
文摘The effect of age hardening on the microstructure,martensitic transformation behavior,and shape memory properties of the(Ni_(50)Ti_(30)Hf_(20))_(95)V_(5)alloy was investigated by scanning electron microscopy,transmission electron microscopy,X-ray diffraction,differential scanning calorimetry,microhardness,and bending tests.The results demonstrate a significant influence of V addition on the microstructure of the alloy.V addition leads to the formation of a(Ni,V)_(2)(Ti,Hf)-type Laves phase,which coexists with B19'martensite at room temperature.Aging at 550℃results in precipitation hardening due to the formation of nano-scale orthorhombic H-phase,with the peak hardness observed after 3 h of aging.The alloy at peak hardness state exhibits higher transformation strain and lower unrecovered strain compared to the solution-treated sample.The aged sample achieves a maximum transformation strain of 1.56%under 500 MPa.
基金sponsored by Shanghai Rising-Star Program with No.17QB1400100
文摘Strain-induced martensitic phase transformation and its influence on the forrnability of newly developed nitrogen-alloyed metastable austenitic stainless steels were systematically investigated. Yield strength for the as- received steels bearing low nickel content was around 300 MPa and their elongation ratios varied from 55.2% to 61.7%. Erichsen numbers of these samples differed from 13.82 to 14.57 mm. Although its Cu content was lower than that of other samples, steel D2 exhibited better plasticity and formability, which was attributed to ~/--,c~＇ martensitic phase transformation. EBSD, XRD, and magnetism tests showed that increases in deformation ratio gradually increased the α＇ martensite phase of a sample ,thereby contributing to its strain and inducing the optimal transformation-induced plasticity effect. An Meeo/5o temperature of around 20 ℃, which is close to the deformation temperature,provided the austenite with adequate stability and gradually transformed it into martensite, thereby endowing lean ASS with better formability.
基金supported by the National Natural Science Foundation of China(Grant No.51474031)
文摘To control the reverse-transformation austenite structure through manipulation of the micro/nanometer grain structure, the influences of cold deformation and annealing parameters on the microstructure evolution and mechanical properties of 316L austenitic stainless steel were investigated. The samples were first cold-rolled, and then samples deformed to different extents were annealed at different temperatures. The microstructure evolutions were analyzed by optical microscopy, scanning electron microscopy (SEM), magnetic measurements, and X-ray diffraction (XRD); the mechanical properties are also determined by tensile tests. The results showed that the fraction of stain-induced martensite was approximately 72% in the 90% cold-rolled steel. The micro/nanometric microstructure was obtained after reversion annealing at 820-870A degrees C for 60 s. Nearly 100% reversed austenite was obtained in samples annealed at 850A degrees C, where grains with a diameter ae<currency> 500 nm accounted for 30% and those with a diameter > 0.5 mu m accounted for 70%. The micro/nanometer-grain steel exhibited not only a high strength level (approximately 959 MPa) but also a desirable elongation of approximately 45%.
文摘Grinding-induced tm phase transformation and the resultant texture in ceria-yttria-doped tetragonal zirconia polycrystals with varied tetragonality have been studied by XRD. It is observed that the reversible tm phase transformation occurs during grinding and the intensity ratio of I(002)t/I(200)t increases with the transformability. The author proposes that the texture induced by grinding at low temperatures is due to the tetragonal variant reorientation via cyclic,reversible tm phase transformation, termed 'transformational domain switching', instead of the ferroelastic one
基金Project (51071056) supported by the National Natural Science Foundation of ChinaProjects (HEUCFR1132, HEUCF121712) supported by the Fundamental Research Funds for the Central Universities of China
文摘Heat treatment of Ti-50.9%Ni （mole fraction） alloy was studied by differential scanning calorimetry, X-ray diffraction, scanning electron microscopey and energy dispersive X-ray analysis to investigate the influence of cooling rate on transformation behavior and microstructures of NiTi shape memory alloy. The experimental results show that three-stage phase transformation can be induced at a very low cooling rate such as cooling in furnace. The cooling rate also has a great influence on the phase transformation temperatures. Both martensitic start transformation temperature （Ms） and martensitic finish transformation temperature （Mf） decrease with the decrease of the cooling rate, and decreasing the cooling rate contributes to enhancing the M→A austenite transformation temperature. The phase transformation hysteresis （Af-Mf） increases with the decrease of the cooling rate. Heat treatment is unable to eliminate the textures formed in hot working of NiTi sample, but can weaken the intensity of them. The cooling rate has little influence on the grain size.
文摘The kinetics of the reversible martensitic transformation in a Cu-Zn-Al-Mn-Ni shape memory alloy has been studied by means of differential scanning calorimetry.The apparent activation energy has been calculated and the kinetic equations of positive and adverse martensitic transformation have been established with the variations of temperature and time.
基金supported by the National Natural Science Foundation for Distinguished Young Scholars of China (Grant No. 50925101)Science Fund for Creative Research Groups of the National Natural Science Foundation of China (Grant No. 50921003)the Fundamental Research Funds for the Central Universities
文摘This paper studies the martensitic transformation in the Cu-doped NiMnGa alloys. The orthorhombic martensite transforms to L21 cubic austenite by Cu substituting for Ni in the Nis0-xCuxMn31Ga19 （x=2 10） alloys, the martensitic transformation temperature decreases significantly with the rate of 40 K per Cu atom addition. The variation of the Fermi sphere radius （kF） is applied to evaluate the change of the martensitic transformation temperature. The increase of kF leads to the increase of the martensitic transformation temperature.
文摘The effects of small amount additions of Sm on the martensitic transition and magnetic phase transition of polycrystalline Ni-Mn-Ga alloys were investigated. The experimental results show that the Sm doped alloys also undergo a thermal-elastic martensitic transformation and reverse transformation during cooling and heating process and the addition of Sm decreases the martensitic transformation temperature and Curie temperature in different degree respectively. Ni-Mn-Ga alloys of adding Sm still possess Heusler structure, but their crystal lattice parameters are modified slightly. The addition of a proper amount of Sm does not basically decrease T_c of the alloy when avoiding the appearance of second phase. In addition, the doped alloys have favorable toughness because of grain refinement of Sm.
文摘The hyperfine interactions of two shape memory alloys have been studied by Mossbauer effect measurement at various temperatures. The Mossbauer spectra exhibit a mag-netic change from antiferro magnetic state to paramagnetic state when the temperuture rises. The Fe-Mn-Si alloys have a small hyperfine field and silicon element increases the hyperfine field and magnetic susceptibility. Thermo-induced γ→ ε trunsforma-tions are suppressed by Neel transition and by increasing carbon content, whereas stress induced γ→ ε transformation occurs in both alloys. Antiferromagnetic spin order can suppress thermo-induced γ→εtransformations efficiently, but cannot sup-press stress induced γ → ε transformation.
文摘Measurements of electrical resistivity, X-ray diffraction, and tensile test at room temperature and ？196°C were performed to investigate the effects of Al addition substituting Ni on the phase transformation behaviors, the mechanical properties, and the shape memory effects of Ti50Ni47Fe2Al1 and Ti50Ni46.5Fe2.5Al1 alloys. It is found that 1at% Al addition dramatically decreases the martensitic start transformation temperature and expands the transformation temperature range of R-phase for TiNiFeAl alloys. The results of tensile test indicate that 1at% Al improves the yield strength of Ti50Ni47Fe2Al1 and Ti50Ni46.5Fe2.5Al1 alloys by 40% and 64%, but de- creases the plasticity to 11% and 12% from 26% and 27% respectively. Moreover, excellent shape memory effect of 6.6% and 7.5% were found in Ti50Ni47Fe2Al1 and Ti50Ni46.5Fe2.5Al1 alloys, which results from the stress-induced martensite transformation from the R-phase.
基金express their gratitude to the Ministry of Education,Culture and Sports of Japan(MEXT) for partially supporting this research
文摘The microstructural features, shape memory behavior and mechanical properties of Ni-Mn based alloys were investigated by differential scanning calorimetry （DSC）, scanning electron microscopy （SEM）, transmission electron microscopy （TEM） and thermal cycling test under various stresses. The transformation temperatures shifted toward lower temperatures when adding a third element into the Ni-Mn system. The addition of 10 at. pct Fe increased considerably the mechanical properties exhibiting still high transformation temperatures. However, it was found that in NiMn40Fe10 alloy the martensitic transformation is not thermoelastic in nature. The mechanism of this transformation and the crystallography of Ni-Mn（50-x）-Fex （x=5, 7, 10, 20 at. pct） alloys are presented.
基金The authors would like to thank the Federal Institute of Science and Technology of Bahia,the University of São Paulo,the University of Brasilia and the PRPGI for all the support to carry out this research.
文摘The present research aimed to analyze the influence that different contents of titanium(x=0.5,0.6 and 0.7 wt.%)have on the martensitic transformation temperature of a Cu-14Al-4Ni(wt.%)SMA(shape memory alloy).The Cu-14Al-4Ni-xTi samples were casted in an arc-melting furnace and rapidly solidified.All samples underwent heat treatment in a tubular furnace at a temperature of 1,100°C for 30 min and water quenched at 25°C.Subsequently,samples were analyzed by SEM(scanning electron microscopy)with EDS(energy dispersive spectroscopy),XRD(X-ray diffraction)and DSC(differential scanning calorimeter).SEM images and XRD patterns showed that the presence of titanium modified the alloy’s microstructure,induced the formation of three titanium rich phases called“X”phase(CuNi2Ti,Cu3Ti and AlCu2Ti)and reduced the presence of the brittle phaseγ2(Cu9Al4)for samples with 0.6 and 0.7 wt.%Ti.The titanium added to the copper based SMA also functioned as a refiner,reducing GS(grain size)up to approximately 80%with the increase of Ti content.DSC results exhibited low enthalpy levels,hysteresis,as well as low start martensitic transformation temperatures.
文摘The effect of deformation via stress-induced martensitic transformation on the reverse transformation behavior of the (Ni47Ti44)100?xNbx (x=3, 9, 15, 20, 30, mole fraction, %) shape memory alloys was investigated in detail by differential scanning calorimetry (DSC) after performing cryogenic tensile tests at a temperature of Ms+30 ℃. The results show that Nb-content has obvious effect on the process of stress-induced martensitic transformation. It is also observed that the stress-induced martensite is stabilized relative to the thermally-induced martensite (TIM) formed on cooling, and Nb-content in Ni-Ti-Nb alloy has great influence on the reverse transformation start temperature and transformation temperature hysteresis of stress-induced martensite(SIM). The mechanism of wide transformation temperature hysteresis was fully explained based on the microscopic structure and the distribution of the elastic strain energy of (Ni47Ti44)100?xNbx alloys.
