Four different types of three-body model composed of rock and coal with different strength and stiffness were established in order to study the failure characteristics of compound model such as roof-coal-floor. Throug...Four different types of three-body model composed of rock and coal with different strength and stiffness were established in order to study the failure characteristics of compound model such as roof-coal-floor. Through stress analysis of the element with variable strength and stiffness extracted from the strong-weak interface, the tri-axial compressive strength of the weak body and strong body near the interface as well as the areas away from the contact surface was found. Then, on the basis of three-dimensional fast Lagrangian method of continua and strain softening constitutive model composed of Coulomb-Mohr shear failure with tensile cut-off, stress and strain relationship of the four three-body combined models were analyzed under different confining pressures by numerical simulation. Finally, the different features of local shear zones and plastic failure areas of the four different models and their development trend with increasing confining pressure were discussed. The results show that additional stresses are derived due to the lateral deformation constraints near the strong-weak interface area, which results in the strength increasing in weak body and strength decreasing in strong body. The weakly consolidated soft rock and coal cementation exhibit significant strain softening behavior and bear compound tension-shear failure under uni-axial compression. With the increase of confining pressure, the tensile failure disappears from the model, and the failure type of composed model changes to local shear failure with different number of shearing bands and plastic failure zones. This work shows important guiding significance for the mechanism study of seismic, rock burst, and coal bump.展开更多
The pozzolanic activity of coal gangue, which is calcining at 500 to 1 000 ℃, differs distinctly. The simplex-centroid design with upper and lower bounds of component proportion is adopted to study the compressive st...The pozzolanic activity of coal gangue, which is calcining at 500 to 1 000 ℃, differs distinctly. The simplex-centroid design with upper and lower bounds of component proportion is adopted to study the compressive strength of mortars made with ternary blends of cement, activated coal gangue and fly ash. Based on the results of a minimum of seven design points, three special cubic polynomial models are used to establish the strength predicating equations at different ages for mortars. Five experimental checkpoints were also designed to verify the precision of the equations. The most frequent errors of the predicted values are within 3%. A simple and practical way is provided for determining the optimal proportion of two admixtures when they are used in concrete.展开更多
The relationship between support and surrounding rock is of great significance to the control of surrounding rock in mining process.In view of the fact that most of the existing numerical simulation methods construct ...The relationship between support and surrounding rock is of great significance to the control of surrounding rock in mining process.In view of the fact that most of the existing numerical simulation methods construct virtual elements and stress servo control to approximately replace the hydraulic support problem,this paper establishes a new numerical model of hydraulic support with the same working characteristics as the actual hydraulic support by integrating numerical simulation software Rhino,Griddle and FLAC3D,which can realize the simulation of different working conditions.Based on this model,the influence mechanism of the supporting strength of hydraulic support on surrounding rock stress regulation and coal stability in front of the top coal caving face in extra thick coal seam were researched.Firstly,under different support intensity,the abutment pressure of the bearing coal and the coal in front of it presents the “three-stage”evolution characteristics.The influence range of support intensity is 15%–30%.Secondly,1.5 MPa is the upper limit of impact that the support strength can have on the front coal failure area.Thirdly,within a displacement range of 2.76 m from the coal wall,a support strength of1.5 MPa provides optimal control of the horizontal displacement of the coal.展开更多
Coal waste(CW)could be used for soil stabilization due to the pozzolanic elements it contains.There hasn’t been much investigation into how different fibers affect the mechanical qualities of stabilized sand,although...Coal waste(CW)could be used for soil stabilization due to the pozzolanic elements it contains.There hasn’t been much investigation into how different fibers affect the mechanical qualities of stabilized sand,although adding fibers of any kind to soils may improve the soil because of fiber characteristics like rigidity.For this reason,several tests were carried out on sand that contained 6%cement(by dry weight of used sand),5 wt%CW,0 wt%,0.25 wt%,and 0.50 wt%fiber,as well as the unconfined compressive strength(UCS)test,indirect tensile strength(ITS)test,unconsolidated undrained(UU)triaxial test,scanning electron microscope(SEM)test and ultrasonic pulse velocity(UPV)test.The results showed that in comparison to other fiber reinforced mix designs,the specimen reinforced with 0.5%fibers and the mix design of 0.25 wt%glass and 0.25 wt%polypropylene(PP)fibers exhibited the maximum strength.Examining the impact of fiber type found that glass fibers influence PP strength more favorably than other fiber types.The use of PP fibers is an excellent solution for the problem of large strains in design processes,while adding glass fibers is considered a suitable treatment for issues related to small strains.展开更多
The effects of activated coal gangue on compressive strength, porosity and pore size distribution of hardened cement pastes were investigated. Activated coal gangue with two different kaolin contents, one higher and o...The effects of activated coal gangue on compressive strength, porosity and pore size distribution of hardened cement pastes were investigated. Activated coal gangue with two different kaolin contents, one higher and one lower, were used to partially replace Portland cement at 0%, 10%, and 30% by weight. The water to binder ratio（w/b） of 0.5 was used for all the blended cement paste mixes. Experimental results indicate that the blended cement of activated coal gangue mortar with higher kaolin mineral content has a higher compressive strength than that with lower kaolin mineral content. The porosity and pore size of blended cement mortar were significantly affected by the replacement of activated coal gangue.展开更多
The coal strength and deformation properties are key factors affecting safe coal mining and highefficiency coalbed methane(CBM)development.In this paper,reconstituted coal samples are chosen to investigate the weakeni...The coal strength and deformation properties are key factors affecting safe coal mining and highefficiency coalbed methane(CBM)development.In this paper,reconstituted coal samples are chosen to investigate the weakening behavior of gas on coal strength,meanwhile,its effects on coal deformation are quantitatively evaluated.The results indicate that the weakening degree of gas on coal strength is closely related to the confining stress and gas pressure.Compared with non-gas-saturated coals,the maximum weakening ratios of adsorbed gas to coal strength are 10.58%,18.12%,8.55%and 14.65%under the conditions of confining stress CS=3 MPa and gas pressure GP=1 MPa,CS=3 MPa and GP=2 MPa,CS=4 MPa and GP=1 MPa,and CS=4 MPa and GP=2 MPa,respectively.Furthermore,the maximum weakening ratios of free gas to coal strength are 18.27%,36.54%,14.79%and 29.58%,respectively,under above four conditions.The maximum coal bulk strain decreases as particle sizes of coal powders increase,and it has a maximum value of 0.0227 and a minimum value of 0.0191 in particle size ranges of 0.01–0.041 and 0.5–1 mm.Under the same conditions,the coal bulk strain increases with increasing gas pressure,revealing that coal deformation properties can be enhanced by gas.展开更多
Coal seam destabilization inflicts damage to equipment, causes property loss and personnel casualties,and severely threatens mining safety and efficient production. To further understand this destabilization based on ...Coal seam destabilization inflicts damage to equipment, causes property loss and personnel casualties,and severely threatens mining safety and efficient production. To further understand this destabilization based on the basic theory of Lippmann seam destabilization, a mathematical model was introduced for gas pressure distribution by considering intermediate principal stress and support resistance.Subsequently, we established a translation model suitable for the entire roadway coal seam with rocky roof and floor by applying the unified form of yield criterion in the state of plane strain. We also obtained the analytic expressions of coal seam stress distribution on both sides of the roadway and the widths of plastic and disturbance zones. Afterward, we analyzed several typical cases with different material yield criteria, obtained the plastic zone widths of the coal seam under different gas pressures, and assessed the effects of support resistance, roadway size, and coal strength on coal seam destabilization. Results showed that: the results obtained on the basis of Wilson and Mohr–Coulomb criteria are considerably conservative, and the use of Druker–Prager criteria to evaluate the rockburst-induced coal seam destabilization is safer than the use of the two other criteria; coal seam stability is correlated with gas pressure;and high-pressure gas accelerates the coal seam destabilization.展开更多
The volume change and shear strength behaviour of tailings slurry with the changes in gravimetric moisture content is important to effectively utilise the storage volume and analysis of dam failure potential.Consolida...The volume change and shear strength behaviour of tailings slurry with the changes in gravimetric moisture content is important to effectively utilise the storage volume and analysis of dam failure potential.Consolidation testing of tailings from a slurry-like to soil-like state is a critical task,and conventional consolidation apparatus does not have the capability of doing such testing,as the tailings slurries contain high water content.Settling tests conducted on slurries having a 25%solids concentration showed very low efficiency;final sediment was still slurry-like.An intrinsic point was identified based on pore water pressure dissipation during consolidation tests in a slurry consolidometer that can define two states of the tailings i.e.slurry-like and soil-like.In the slurry-like state,the volume change was greater for Slurry 2 than Slurry 1,while the inverse was observed in the soil-like state.The evolution of peak vane shear strength with the changes in moisture content was almost similar for both samples and obeyed the power function.Regression models have been developed and validated to predict the shear strength of materials at any gravimetric moisture content or void ratio.展开更多
CaO-containing carbon pellets(CCCP)were successfully prepared from well-mixed coking coal(CC)and calcium oxide(CaO)and roasted at different pyrolysis temperatures.The effects of temperature,pore distribution,and carbo...CaO-containing carbon pellets(CCCP)were successfully prepared from well-mixed coking coal(CC)and calcium oxide(CaO)and roasted at different pyrolysis temperatures.The effects of temperature,pore distribution,and carbon structure on the compressive strength of CCCP was investigated in a pyrolysis furnace(350-750℃).The results showed that as the roasting temperature increased,the compressive strength also increased and furthermore,structural defects and imperfections in the carbon crystallites were gradually eliminated to form more organized char structures,thus forming high-ordered CC.Notably,the CCCP preheated at 750℃exhibited the highest compressive strength.A positive relationship between the compressive strength and pore-size homogeneity was established.A linear relationship between the com-pressive strength of the CCCP and the average stack height of CC was observed.Additionally,a four-stage caking mechanism was developed.展开更多
The crack volume strain method and acoustic emission(AE)method are used to analyze the anisotropy of the crack initiation strength,damage strength,the failure mode and the AE characteristics of coal reservoir.The resu...The crack volume strain method and acoustic emission(AE)method are used to analyze the anisotropy of the crack initiation strength,damage strength,the failure mode and the AE characteristics of coal reservoir.The results show that coal reservoirs show obvious anisotropic characteristics in compressive strength,cracking initiation strength and damage strength.The compressive strength of coal reservoirs decreases with the increase of bedding angle,but the reservoirs with bedding angles of 450 and 900 differ little in compressive strength.The crack initiation strength and damage strength decrease first and then increase with the increase of bedding angle.The crack initiation strength and damage strength are the highest,at the bedding angle of 0°,moderate at the bedding angle of 90°,and lowest at the bedding angle of 45°.When the bedding angle is 0°,the failure of the coal reservoirs is mainly steady propagation of large-scale fractures.When the bedding angle is 45°,one type of failure is caused by steady propagation of small-scale fractures,and the other type of failure is due to a sudden instability of large-scale fractures.When the bedding angle is 90°,the failure is mainly demonstrated by a sudden-instability of small-scale fractures.Compared with the cumulative count method of the AE,the cumulative energy method is more suitable for determining crack initiation strength and damage strength of coal reservoirs.展开更多
The aim of this research is to determine the effect of bridging liquid surface tension and specific surface area on strength factor of coal agglomerates. The production of coal agglomerates of the range 15-27.51 mm wa...The aim of this research is to determine the effect of bridging liquid surface tension and specific surface area on strength factor of coal agglomerates. The production of coal agglomerates of the range 15-27.51 mm was achieved. The crushing strength of the agglomerates was determined for good handling of fine （coal-liquid mixture） to improve fugitive dust control, decrease in transportation losses, reduce risk of coal freezing, lower risk of spontaneous combustion, etc. in iron and steel industries, railway corporations and coal corporations. Kerosene （paraffin oil） was used as a binder and the agglomerated coal oil mixture was pelletized using balling technique （disc）. Mechanical and physical tests like compressive strength test, etc. were carried out. The relationship between the bridging liquid surface tension and specific surface area on strength factor of coal agglomerates showed that there is considerable variation in these parameters in the coal powder systems.展开更多
The stability of room mining coal pillars during their secondary mining for recovering coal was analyzed. An analysis was performed for the damage and instability mechanism of coal pillars recovered by the caving mini...The stability of room mining coal pillars during their secondary mining for recovering coal was analyzed. An analysis was performed for the damage and instability mechanism of coal pillars recovered by the caving mining method. During the damage progression of a single room coal pillar, the shape of the stress distribution in the pillar transformed from the initial stable saddle shape to the final arch-shaped distribution of critical instability. By combining the shapes of stress distribution in the coal pillars with the ultimate strength theory, the safe-stress value of coal pillar was obtained as 11.8 MPa. The mechanism of instability of coal pillar groups recovered by the caving mining method was explained by the domino effect. Since the room coal pillars mined and recovered by the traditional caving mining method were significantly influenced by the secondary mining during recovery, the coal pillars would go through a chain-type instability failure. Because of this limitation, the method of solid backfilling was proposed for mining and recovering room coal pillars, thus changing the transfer mechanism of stress caused by the secondary mining(recovery) of coal pillars. The mechanical model of the stope in the case of backfilling and recovering room coal pillars was built. The peak stress values inside coal pillars varied with the variance of backfilling ratio when the working face was advanced by 150 m. Furthermore, when the critical backfilling ratio was 80.6%, the instability failure of coal pillars would not occur during the solid backfill mining process. By taking Bandingliang Coal Mine as an example, the coal pillars' stability of stope under this backfilling ratio was studied, and a project scheme was designed.展开更多
This paper attempts to quantify the effect of backfilling on pillar strength in highwall mining using numerical modelling. Calibration against the new empirical strength formula for highwall mining was conducted to ob...This paper attempts to quantify the effect of backfilling on pillar strength in highwall mining using numerical modelling. Calibration against the new empirical strength formula for highwall mining was conducted to obtain the material parameters used in the numerical modelling. With the obtained coal strength parameters, three sets of backfill properties were investigated. The results reveal that the behavior of pillars varies with the type and amount of backfill as well as the pillar width to mining height ratio(w/h). In case of cohesive backfill, generally 75% backfill shows a significant increase in peak strength, and the increase in peak strength is more pronounced for the pillars having lower w/h ratios. In case of noncohesive backfill, the changes in both the peak and residual strengths with up to 92% backfill are negligible while the residual strength constantly increases after reaching the peak strength only when 100%backfill is placed. Based on the modelling results, different backfilling strategies should be considered on a case by case basis depending on the type of backfill available and desired pillar dimension.展开更多
The pozzolanic activity of coal gangue burned at different burning temperatures was investigated. The burned coal gangue was mixed with portland cement in different proportions （ 20% - 60% ）. The pozzolanic activity...The pozzolanic activity of coal gangue burned at different burning temperatures was investigated. The burned coal gangue was mixed with portland cement in different proportions （ 20% - 60% ）. The pozzolanic activity of coal gangue burned and the hydration products were examined, the compressive strengths of the pastes of the mixtures were tested, and the mechanism of the reaction was discussed. The experimental results slum, that the coal gangue burned at 750 ℃ has the optimum pozzolanic activity, and the burned coal ganguc with SiO2 and Al2 O3 is in an active form. When the coal gangue burned at 750℃ is mixed into portland cement, the content of calcium hydroxide in paste is significantly reduced, while the contents of hydrated calcium silk.ate and hydrated calcium aluminate are increased accordingly, hence resulting in the improvement of the microstructure of mortar. The compressive strength of cement paste decreases with increasing the content of burncd coal gangue. The decease in strength is small in the range of 20% - 30% coal gangue substitution and significant in 30%- 60% substitution.展开更多
The method of determining coal pillar strength equations from databases of stable and failed case histories is more than 50 years old and has been applied in different countries by different researchers in a range of ...The method of determining coal pillar strength equations from databases of stable and failed case histories is more than 50 years old and has been applied in different countries by different researchers in a range of mining situations. While common wisdom sensibly limits the use of the resultant pillar strength equations and methods to design scenarios that are consistent with the founding database, there are a number of examples where failures have occurred as a direct result of applying empirical design methods to coal pillar design problems that are inconsistent with the founding database. This paper explores the reasons why empirically derived coal pillar strength equations tend to be problem-specific and should be considered as providing no more than a pillar strength ‘‘index." These include the non-consideration of overburden horizontal stress within the mine stability problem, an inadequate definition of supercritical overburden behavior as it applies to standing coal pillars, and the non-consideration of overburden displacement and coal pillar strain limits. All of which combine to potentially complicate and confuse the back-analysis of coal pillar strength from failed cases. A modified coal pillar design representation and model are presented based on coal pillars acting to reinforce a horizontally stressed overburden, rather than suspend an otherwise unstable self-loaded overburden or section, the latter having been at the core of historical empirical studies into coal pillar strength and stability.展开更多
The rock mass rating(RMR)has been used across the geotechnical industry for half a century.In contrast,the coal mine roof rating(CMRR)was specifically introduced to underground coal mines two decades ago to link geolo...The rock mass rating(RMR)has been used across the geotechnical industry for half a century.In contrast,the coal mine roof rating(CMRR)was specifically introduced to underground coal mines two decades ago to link geological characterization with geotechnical risk mitigation.The premise of CMRR is that strength properties of mine roof rock are influenced by defects typical of coal measures stratigraphy.The CMRR has been used in longwall pillar design,roof support methods,and evaluation of extended cuts,but is rarely evaluated.Here,the RMR and CMRR are applied to a longwall coal mine.Roof rock mass classifications were undertaken at 67 locations across the mine.Both classifications showed marked spatial variability in terms of roof conditions.Normal and reverse faulting occur across the mine,and while no clear relationships exist between rock mass character and faulting,a central graben zone showed heterogeneous rock mass properties,and divergence between CMRR and RMR.Overall,the CMRR data fell within the broad envelope of results reported for extended cuts at Australian and U.S.coal mines.The corollary is that the CMRR is useful,and should not be used in isolation,but rather as a component of a strata control programme.展开更多
During high-intensity,fully mechanized mining of extra-thick coal seam,the top coal would cave to a certain 3D form.Based on the data collected during drilling,a 3D model of top coal caving surface space was establish...During high-intensity,fully mechanized mining of extra-thick coal seam,the top coal would cave to a certain 3D form.Based on the data collected during drilling,a 3D model of top coal caving surface space was established to determine the relationship between the location of the stope roof and the caving surface,enabling the mathematical computation of the top caving angle(φ).The drilling method was employed to measure the top caving angle on two extra-thick fully mechanized coal caving faces under the conditions of three geological structures,namely,no geological structure,igneous rock structure,and fault structure.The results show that the value of top caving angle could be accurately estimated on-site with the 9-parameter 3D top coal caving surface model built with the drilling method.This method is a novel on-site measurement that can be easily applied.Our findings reveal that the characteristics of the coal-rock in the two mining faces are different;yet their caving angles follow the ruleφ_(igneous rock structure)<φ_(no geological structure)<φ_(fault structure).Finally,through the data fitting with two indexes(the top coal uniaxial compressive strength and the top caving angle),it is found that the relationship between the two indexes satisfies an exponential decay function.展开更多
In the early 1990 s, the Foundation for Science and Technology of Rio Grande do Sul State(CIENTEC)developed a pioneering study in Brazil, related to the simultaneous mining of multiple coal seams.One of the activities...In the early 1990 s, the Foundation for Science and Technology of Rio Grande do Sul State(CIENTEC)developed a pioneering study in Brazil, related to the simultaneous mining of multiple coal seams.One of the activities included detailed studies on the geomechanical characterization of materials present in the Irapua coal seam, under exploitation in the A-Sangao Mine, located near the city of Criciuma-SC,within the South-Catarinense coalfield. The goal of the laboratory tests was to define the behavior of the uniaxial compressive strength of the Irapua coal seam and establish a first approximation for the in situ strength value of this coal seam, since existing knowledge is solely based on practical mining experience over the years. Large samples of the coal seam were collected, using special techniques to maintain the integrity of the material, and a set of 56 uniaxial compression tests in cubic specimens, with side length ranging from 4.5 to 31 cm, were conducted in laboratory. This paper describes the experimental techniques used in the assays, and also presents the uniaxial compression strength results obtained.Moreover, important aspects of this type of study are considered, highlighting the size effect for the carbonaceous bed and the estimation of in situ strength values for the Irapua coal seam.展开更多
Bumps in coal mines have been recognized as a major hazard for many years. These sudden and violent failures around mine openings have compromised safety, ventilation and access to mine workings.Previous studies showe...Bumps in coal mines have been recognized as a major hazard for many years. These sudden and violent failures around mine openings have compromised safety, ventilation and access to mine workings.Previous studies showed that the violence of coal specimen failure depends on both the interface friction and width-to-height（W/H） ratio of coal specimen. The mode of failure for a uniaxially loaded coal specimen or a coal pillar is a combination of both shear failure along the interface and compressive failure in the coal. The shear failure along the interface triggered the compressive failure in coal. The compressive failure of a coal specimen or a coal pillar can be controlled by changing its W/H ratio. As the W/H ratio increases, the ultimate strength increases. Hence, with a proper combination of interface friction and the W/H ratio of pillar or coal specimen, the mode of failure will change from sudden violent failure which is brittle failure to non-violent failure which is ductile failure. The main objective of this paper is to determine at what W/H ratio and interface friction the mode of failure changes from violent to non-violent. In this research, coal specimens of W/H ratio ranging from 1 to 10 were uniaxially tested under two interface frictions of 0.1 and 0.25, and the results are presented and discussed.展开更多
基金Project(51174128)supported by the National Natural Science Foundation of ChinaProject(20123718110007)supported by the Specialized Research Fund for the Doctoral Program of Higher Education of China
文摘Four different types of three-body model composed of rock and coal with different strength and stiffness were established in order to study the failure characteristics of compound model such as roof-coal-floor. Through stress analysis of the element with variable strength and stiffness extracted from the strong-weak interface, the tri-axial compressive strength of the weak body and strong body near the interface as well as the areas away from the contact surface was found. Then, on the basis of three-dimensional fast Lagrangian method of continua and strain softening constitutive model composed of Coulomb-Mohr shear failure with tensile cut-off, stress and strain relationship of the four three-body combined models were analyzed under different confining pressures by numerical simulation. Finally, the different features of local shear zones and plastic failure areas of the four different models and their development trend with increasing confining pressure were discussed. The results show that additional stresses are derived due to the lateral deformation constraints near the strong-weak interface area, which results in the strength increasing in weak body and strength decreasing in strong body. The weakly consolidated soft rock and coal cementation exhibit significant strain softening behavior and bear compound tension-shear failure under uni-axial compression. With the increase of confining pressure, the tensile failure disappears from the model, and the failure type of composed model changes to local shear failure with different number of shearing bands and plastic failure zones. This work shows important guiding significance for the mechanism study of seismic, rock burst, and coal bump.
基金The National Basic Research Program of China (973Program)(No2000CB610703)
文摘The pozzolanic activity of coal gangue, which is calcining at 500 to 1 000 ℃, differs distinctly. The simplex-centroid design with upper and lower bounds of component proportion is adopted to study the compressive strength of mortars made with ternary blends of cement, activated coal gangue and fly ash. Based on the results of a minimum of seven design points, three special cubic polynomial models are used to establish the strength predicating equations at different ages for mortars. Five experimental checkpoints were also designed to verify the precision of the equations. The most frequent errors of the predicted values are within 3%. A simple and practical way is provided for determining the optimal proportion of two admixtures when they are used in concrete.
基金supported by Distinguished Youth Funds of National Natural Science Foundation of China (No.51925402)National Natural Science Foundation of China (Nos.51904203 and 52174125)+4 种基金the China Postdoctoral Science Foundation (No.2021M702049)the Tencent Foundation or XPLORER PRIZEShanxi Science and Technology Major Project Funds (No.20201102004)Shanxi-Zheda Institute of Advanced Materials and Chemical Engineering (No.2021SX-TD001)Open Fund Research Project Supported by State Key Laboratory of Strata Intelligent Control and Green Mining Co-founded by Shandong Province and the Ministry of Science and Technology (No.SICGM202209)。
文摘The relationship between support and surrounding rock is of great significance to the control of surrounding rock in mining process.In view of the fact that most of the existing numerical simulation methods construct virtual elements and stress servo control to approximately replace the hydraulic support problem,this paper establishes a new numerical model of hydraulic support with the same working characteristics as the actual hydraulic support by integrating numerical simulation software Rhino,Griddle and FLAC3D,which can realize the simulation of different working conditions.Based on this model,the influence mechanism of the supporting strength of hydraulic support on surrounding rock stress regulation and coal stability in front of the top coal caving face in extra thick coal seam were researched.Firstly,under different support intensity,the abutment pressure of the bearing coal and the coal in front of it presents the “three-stage”evolution characteristics.The influence range of support intensity is 15%–30%.Secondly,1.5 MPa is the upper limit of impact that the support strength can have on the front coal failure area.Thirdly,within a displacement range of 2.76 m from the coal wall,a support strength of1.5 MPa provides optimal control of the horizontal displacement of the coal.
文摘Coal waste(CW)could be used for soil stabilization due to the pozzolanic elements it contains.There hasn’t been much investigation into how different fibers affect the mechanical qualities of stabilized sand,although adding fibers of any kind to soils may improve the soil because of fiber characteristics like rigidity.For this reason,several tests were carried out on sand that contained 6%cement(by dry weight of used sand),5 wt%CW,0 wt%,0.25 wt%,and 0.50 wt%fiber,as well as the unconfined compressive strength(UCS)test,indirect tensile strength(ITS)test,unconsolidated undrained(UU)triaxial test,scanning electron microscope(SEM)test and ultrasonic pulse velocity(UPV)test.The results showed that in comparison to other fiber reinforced mix designs,the specimen reinforced with 0.5%fibers and the mix design of 0.25 wt%glass and 0.25 wt%polypropylene(PP)fibers exhibited the maximum strength.Examining the impact of fiber type found that glass fibers influence PP strength more favorably than other fiber types.The use of PP fibers is an excellent solution for the problem of large strains in design processes,while adding glass fibers is considered a suitable treatment for issues related to small strains.
基金the National Basic Research Program of China(No.2001CB610703)the Basic Research of Preparation and Application of High Performance Cement
文摘The effects of activated coal gangue on compressive strength, porosity and pore size distribution of hardened cement pastes were investigated. Activated coal gangue with two different kaolin contents, one higher and one lower, were used to partially replace Portland cement at 0%, 10%, and 30% by weight. The water to binder ratio（w/b） of 0.5 was used for all the blended cement paste mixes. Experimental results indicate that the blended cement of activated coal gangue mortar with higher kaolin mineral content has a higher compressive strength than that with lower kaolin mineral content. The porosity and pore size of blended cement mortar were significantly affected by the replacement of activated coal gangue.
基金financial support from the National Natural Science Foundation of China(Nos.51904310and 51874314)the Fundamental Research Funds for the Central Universities(No.2020YQAQ03)+2 种基金the Open Funds of Key Laboratory of Safety and High-efficiency Coal MiningMinistry of Education(Anhui University of Science and Technology)(No.JYBSYS2019204)the Open Funds of State Key Laboratory Cultivation Base for Gas Geology and Gas Control(Henan Polytechnic University)(No.WS2018B06)。
文摘The coal strength and deformation properties are key factors affecting safe coal mining and highefficiency coalbed methane(CBM)development.In this paper,reconstituted coal samples are chosen to investigate the weakening behavior of gas on coal strength,meanwhile,its effects on coal deformation are quantitatively evaluated.The results indicate that the weakening degree of gas on coal strength is closely related to the confining stress and gas pressure.Compared with non-gas-saturated coals,the maximum weakening ratios of adsorbed gas to coal strength are 10.58%,18.12%,8.55%and 14.65%under the conditions of confining stress CS=3 MPa and gas pressure GP=1 MPa,CS=3 MPa and GP=2 MPa,CS=4 MPa and GP=1 MPa,and CS=4 MPa and GP=2 MPa,respectively.Furthermore,the maximum weakening ratios of free gas to coal strength are 18.27%,36.54%,14.79%and 29.58%,respectively,under above four conditions.The maximum coal bulk strain decreases as particle sizes of coal powders increase,and it has a maximum value of 0.0227 and a minimum value of 0.0191 in particle size ranges of 0.01–0.041 and 0.5–1 mm.Under the same conditions,the coal bulk strain increases with increasing gas pressure,revealing that coal deformation properties can be enhanced by gas.
基金support of National Natural Science Foundation of China (Nos. 51674158 and 51604168)the Natural Science Foundation of Shandong Provincial (No. ZR2016EEQ18)+2 种基金and the Source Innovation Program (Applied Research Special-Youth Special) of Qingdao (No. 17-1-138-jch)Shandong University of Science and Technology ResearchFund (No. 2015JQJH105)the Taishan Scholar Talent Team Support Plan for Advantaged & Unique Discipline Areas
文摘Coal seam destabilization inflicts damage to equipment, causes property loss and personnel casualties,and severely threatens mining safety and efficient production. To further understand this destabilization based on the basic theory of Lippmann seam destabilization, a mathematical model was introduced for gas pressure distribution by considering intermediate principal stress and support resistance.Subsequently, we established a translation model suitable for the entire roadway coal seam with rocky roof and floor by applying the unified form of yield criterion in the state of plane strain. We also obtained the analytic expressions of coal seam stress distribution on both sides of the roadway and the widths of plastic and disturbance zones. Afterward, we analyzed several typical cases with different material yield criteria, obtained the plastic zone widths of the coal seam under different gas pressures, and assessed the effects of support resistance, roadway size, and coal strength on coal seam destabilization. Results showed that: the results obtained on the basis of Wilson and Mohr–Coulomb criteria are considerably conservative, and the use of Druker–Prager criteria to evaluate the rockburst-induced coal seam destabilization is safer than the use of the two other criteria; coal seam stability is correlated with gas pressure;and high-pressure gas accelerates the coal seam destabilization.
文摘The volume change and shear strength behaviour of tailings slurry with the changes in gravimetric moisture content is important to effectively utilise the storage volume and analysis of dam failure potential.Consolidation testing of tailings from a slurry-like to soil-like state is a critical task,and conventional consolidation apparatus does not have the capability of doing such testing,as the tailings slurries contain high water content.Settling tests conducted on slurries having a 25%solids concentration showed very low efficiency;final sediment was still slurry-like.An intrinsic point was identified based on pore water pressure dissipation during consolidation tests in a slurry consolidometer that can define two states of the tailings i.e.slurry-like and soil-like.In the slurry-like state,the volume change was greater for Slurry 2 than Slurry 1,while the inverse was observed in the soil-like state.The evolution of peak vane shear strength with the changes in moisture content was almost similar for both samples and obeyed the power function.Regression models have been developed and validated to predict the shear strength of materials at any gravimetric moisture content or void ratio.
基金This work was financially supported by the National Key R&D Program of China(No.2018YFB0605900).
文摘CaO-containing carbon pellets(CCCP)were successfully prepared from well-mixed coking coal(CC)and calcium oxide(CaO)and roasted at different pyrolysis temperatures.The effects of temperature,pore distribution,and carbon structure on the compressive strength of CCCP was investigated in a pyrolysis furnace(350-750℃).The results showed that as the roasting temperature increased,the compressive strength also increased and furthermore,structural defects and imperfections in the carbon crystallites were gradually eliminated to form more organized char structures,thus forming high-ordered CC.Notably,the CCCP preheated at 750℃exhibited the highest compressive strength.A positive relationship between the compressive strength and pore-size homogeneity was established.A linear relationship between the com-pressive strength of the CCCP and the average stack height of CC was observed.Additionally,a four-stage caking mechanism was developed.
基金Supported by the National Natural Science Foundation of China(51804309,51861145403)State Key Laboratory of Water Resource Protection and Utilization in Coal Mining,China(SHJT-17-42.10)。
文摘The crack volume strain method and acoustic emission(AE)method are used to analyze the anisotropy of the crack initiation strength,damage strength,the failure mode and the AE characteristics of coal reservoir.The results show that coal reservoirs show obvious anisotropic characteristics in compressive strength,cracking initiation strength and damage strength.The compressive strength of coal reservoirs decreases with the increase of bedding angle,but the reservoirs with bedding angles of 450 and 900 differ little in compressive strength.The crack initiation strength and damage strength decrease first and then increase with the increase of bedding angle.The crack initiation strength and damage strength are the highest,at the bedding angle of 0°,moderate at the bedding angle of 90°,and lowest at the bedding angle of 45°.When the bedding angle is 0°,the failure of the coal reservoirs is mainly steady propagation of large-scale fractures.When the bedding angle is 45°,one type of failure is caused by steady propagation of small-scale fractures,and the other type of failure is due to a sudden instability of large-scale fractures.When the bedding angle is 90°,the failure is mainly demonstrated by a sudden-instability of small-scale fractures.Compared with the cumulative count method of the AE,the cumulative energy method is more suitable for determining crack initiation strength and damage strength of coal reservoirs.
文摘The aim of this research is to determine the effect of bridging liquid surface tension and specific surface area on strength factor of coal agglomerates. The production of coal agglomerates of the range 15-27.51 mm was achieved. The crushing strength of the agglomerates was determined for good handling of fine （coal-liquid mixture） to improve fugitive dust control, decrease in transportation losses, reduce risk of coal freezing, lower risk of spontaneous combustion, etc. in iron and steel industries, railway corporations and coal corporations. Kerosene （paraffin oil） was used as a binder and the agglomerated coal oil mixture was pelletized using balling technique （disc）. Mechanical and physical tests like compressive strength test, etc. were carried out. The relationship between the bridging liquid surface tension and specific surface area on strength factor of coal agglomerates showed that there is considerable variation in these parameters in the coal powder systems.
基金Project(2014ZDPY02)supported by the Fundamental Research Funds for the Central Universities
文摘The stability of room mining coal pillars during their secondary mining for recovering coal was analyzed. An analysis was performed for the damage and instability mechanism of coal pillars recovered by the caving mining method. During the damage progression of a single room coal pillar, the shape of the stress distribution in the pillar transformed from the initial stable saddle shape to the final arch-shaped distribution of critical instability. By combining the shapes of stress distribution in the coal pillars with the ultimate strength theory, the safe-stress value of coal pillar was obtained as 11.8 MPa. The mechanism of instability of coal pillar groups recovered by the caving mining method was explained by the domino effect. Since the room coal pillars mined and recovered by the traditional caving mining method were significantly influenced by the secondary mining during recovery, the coal pillars would go through a chain-type instability failure. Because of this limitation, the method of solid backfilling was proposed for mining and recovering room coal pillars, thus changing the transfer mechanism of stress caused by the secondary mining(recovery) of coal pillars. The mechanical model of the stope in the case of backfilling and recovering room coal pillars was built. The peak stress values inside coal pillars varied with the variance of backfilling ratio when the working face was advanced by 150 m. Furthermore, when the critical backfilling ratio was 80.6%, the instability failure of coal pillars would not occur during the solid backfill mining process. By taking Bandingliang Coal Mine as an example, the coal pillars' stability of stope under this backfilling ratio was studied, and a project scheme was designed.
文摘This paper attempts to quantify the effect of backfilling on pillar strength in highwall mining using numerical modelling. Calibration against the new empirical strength formula for highwall mining was conducted to obtain the material parameters used in the numerical modelling. With the obtained coal strength parameters, three sets of backfill properties were investigated. The results reveal that the behavior of pillars varies with the type and amount of backfill as well as the pillar width to mining height ratio(w/h). In case of cohesive backfill, generally 75% backfill shows a significant increase in peak strength, and the increase in peak strength is more pronounced for the pillars having lower w/h ratios. In case of noncohesive backfill, the changes in both the peak and residual strengths with up to 92% backfill are negligible while the residual strength constantly increases after reaching the peak strength only when 100%backfill is placed. Based on the modelling results, different backfilling strategies should be considered on a case by case basis depending on the type of backfill available and desired pillar dimension.
基金Funded by Social Development Plan in Science and Technologyof Jiangsu Province (No.BS2006033)
文摘The pozzolanic activity of coal gangue burned at different burning temperatures was investigated. The burned coal gangue was mixed with portland cement in different proportions （ 20% - 60% ）. The pozzolanic activity of coal gangue burned and the hydration products were examined, the compressive strengths of the pastes of the mixtures were tested, and the mechanism of the reaction was discussed. The experimental results slum, that the coal gangue burned at 750 ℃ has the optimum pozzolanic activity, and the burned coal ganguc with SiO2 and Al2 O3 is in an active form. When the coal gangue burned at 750℃ is mixed into portland cement, the content of calcium hydroxide in paste is significantly reduced, while the contents of hydrated calcium silk.ate and hydrated calcium aluminate are increased accordingly, hence resulting in the improvement of the microstructure of mortar. The compressive strength of cement paste decreases with increasing the content of burncd coal gangue. The decease in strength is small in the range of 20% - 30% coal gangue substitution and significant in 30%- 60% substitution.
文摘The method of determining coal pillar strength equations from databases of stable and failed case histories is more than 50 years old and has been applied in different countries by different researchers in a range of mining situations. While common wisdom sensibly limits the use of the resultant pillar strength equations and methods to design scenarios that are consistent with the founding database, there are a number of examples where failures have occurred as a direct result of applying empirical design methods to coal pillar design problems that are inconsistent with the founding database. This paper explores the reasons why empirically derived coal pillar strength equations tend to be problem-specific and should be considered as providing no more than a pillar strength ‘‘index." These include the non-consideration of overburden horizontal stress within the mine stability problem, an inadequate definition of supercritical overburden behavior as it applies to standing coal pillars, and the non-consideration of overburden displacement and coal pillar strain limits. All of which combine to potentially complicate and confuse the back-analysis of coal pillar strength from failed cases. A modified coal pillar design representation and model are presented based on coal pillars acting to reinforce a horizontally stressed overburden, rather than suspend an otherwise unstable self-loaded overburden or section, the latter having been at the core of historical empirical studies into coal pillar strength and stability.
基金financially supported by the Project of the Science and Technology Creative Team of Universities in Jiangxi Province,China(No.00008713)the Open Foundation of Jiangxi Key Laboratory for Advanced Copper and Tungsten Materials(No.2013-KLP-04)
基金Staff at Vale Australia,in particular Lachlan Cunningham and Priscilla Page,are thanked for facilitating underground access to the Carborough Downs Mine.The research was kindly supported by Moultrie Group and Golder Associates.
文摘The rock mass rating(RMR)has been used across the geotechnical industry for half a century.In contrast,the coal mine roof rating(CMRR)was specifically introduced to underground coal mines two decades ago to link geological characterization with geotechnical risk mitigation.The premise of CMRR is that strength properties of mine roof rock are influenced by defects typical of coal measures stratigraphy.The CMRR has been used in longwall pillar design,roof support methods,and evaluation of extended cuts,but is rarely evaluated.Here,the RMR and CMRR are applied to a longwall coal mine.Roof rock mass classifications were undertaken at 67 locations across the mine.Both classifications showed marked spatial variability in terms of roof conditions.Normal and reverse faulting occur across the mine,and while no clear relationships exist between rock mass character and faulting,a central graben zone showed heterogeneous rock mass properties,and divergence between CMRR and RMR.Overall,the CMRR data fell within the broad envelope of results reported for extended cuts at Australian and U.S.coal mines.The corollary is that the CMRR is useful,and should not be used in isolation,but rather as a component of a strata control programme.
基金This work was supported by the Science and Technology Innovation Project of Higher Education in Shanxi Province(No.2019L0754)Central Guiding Local Science and Technology Development Fund project(No.YDZJSX2021B021)the Datong Science and Technology Plan Project(No.2019122).
文摘During high-intensity,fully mechanized mining of extra-thick coal seam,the top coal would cave to a certain 3D form.Based on the data collected during drilling,a 3D model of top coal caving surface space was established to determine the relationship between the location of the stope roof and the caving surface,enabling the mathematical computation of the top caving angle(φ).The drilling method was employed to measure the top caving angle on two extra-thick fully mechanized coal caving faces under the conditions of three geological structures,namely,no geological structure,igneous rock structure,and fault structure.The results show that the value of top caving angle could be accurately estimated on-site with the 9-parameter 3D top coal caving surface model built with the drilling method.This method is a novel on-site measurement that can be easily applied.Our findings reveal that the characteristics of the coal-rock in the two mining faces are different;yet their caving angles follow the ruleφ_(igneous rock structure)<φ_(no geological structure)<φ_(fault structure).Finally,through the data fitting with two indexes(the top coal uniaxial compressive strength and the top caving angle),it is found that the relationship between the two indexes satisfies an exponential decay function.
文摘In the early 1990 s, the Foundation for Science and Technology of Rio Grande do Sul State(CIENTEC)developed a pioneering study in Brazil, related to the simultaneous mining of multiple coal seams.One of the activities included detailed studies on the geomechanical characterization of materials present in the Irapua coal seam, under exploitation in the A-Sangao Mine, located near the city of Criciuma-SC,within the South-Catarinense coalfield. The goal of the laboratory tests was to define the behavior of the uniaxial compressive strength of the Irapua coal seam and establish a first approximation for the in situ strength value of this coal seam, since existing knowledge is solely based on practical mining experience over the years. Large samples of the coal seam were collected, using special techniques to maintain the integrity of the material, and a set of 56 uniaxial compression tests in cubic specimens, with side length ranging from 4.5 to 31 cm, were conducted in laboratory. This paper describes the experimental techniques used in the assays, and also presents the uniaxial compression strength results obtained.Moreover, important aspects of this type of study are considered, highlighting the size effect for the carbonaceous bed and the estimation of in situ strength values for the Irapua coal seam.
基金sponsored by Coal and Energy Research Bureau and CDC-NIOSH under Grant No.R01OH009532
文摘Bumps in coal mines have been recognized as a major hazard for many years. These sudden and violent failures around mine openings have compromised safety, ventilation and access to mine workings.Previous studies showed that the violence of coal specimen failure depends on both the interface friction and width-to-height（W/H） ratio of coal specimen. The mode of failure for a uniaxially loaded coal specimen or a coal pillar is a combination of both shear failure along the interface and compressive failure in the coal. The shear failure along the interface triggered the compressive failure in coal. The compressive failure of a coal specimen or a coal pillar can be controlled by changing its W/H ratio. As the W/H ratio increases, the ultimate strength increases. Hence, with a proper combination of interface friction and the W/H ratio of pillar or coal specimen, the mode of failure will change from sudden violent failure which is brittle failure to non-violent failure which is ductile failure. The main objective of this paper is to determine at what W/H ratio and interface friction the mode of failure changes from violent to non-violent. In this research, coal specimens of W/H ratio ranging from 1 to 10 were uniaxially tested under two interface frictions of 0.1 and 0.25, and the results are presented and discussed.
