In order to provide a theoretical basis for methane sensor placement in the vertical direction of a tunnel,the software Fluent was used to simulate methane distribution. A geometric roadway model was established and d...In order to provide a theoretical basis for methane sensor placement in the vertical direction of a tunnel,the software Fluent was used to simulate methane distribution. A geometric roadway model was established and divided by grids. Methane distribution in both level and vertical sections was simulated using a realizable k-ε model with the Fluent software according to a conservation equation in a turbulent state,a turbulent kinetic energy equation and a turbulent dissipation rate equation. The realizable k-ε model and the Fluent software were used to simulate methane distribution according to the principle of the conservation equation in a state of turbulent flow. The results show that after overflow-ing,a methane level with a certain thickness is formed. Methane density curves at three specific levels were internally consistent and methane density at higher levels is denser than that at lower levels. Methane distribution becomes thinner in the direction of wind and methane in the vertical direction becomes uniform if wind speed is high. The distance be-tween sensors and roof should be less than 300 mm which is in agreement with mine safety regulations.展开更多
Estimation of lateral displacement and acceleration responses is essential to assess safety and serviceability of high-rise buildings under dynamic loadings including earthquake excitations. However, the measurement i...Estimation of lateral displacement and acceleration responses is essential to assess safety and serviceability of high-rise buildings under dynamic loadings including earthquake excitations. However, the measurement information from the limited number of sensors installed in a building structure is often insufficient for the complete structural performance assessment. An integrated multi-type sensor placement and response reconstruction method has thus been proposed by the authors to tackle this problem. To validate the feasibility and effectiveness of the proposed method, an experimental investigation using a cantilever beam with multi-type sensors is performed and reported in this paper. The experimental setup is first introduced. The finite element modelling and model updating of the cantilever beam are then performed. The optimal sensor placement for the best response reconstruction is determined by the proposed method based on the updated FE model of the beam. After the sensors are installed on the physical cantilever beam, a number of experiments are carried out. The responses at key locations are reconstructed and compared with the measured ones. The reconstructed responses achieve a good match with the measured ones, manifesting the feasibility and effectiveness of the proposed method. Besides, the proposed method is also examined for the cases of different excitations and unknown excitation, and the results prove the proposed method to be robust and effective. The superiority of the optimized sensor placement scheme is finally demonstrated through comparison with two other different sensor placement schemes： the accelerometer-only scheme and non-optimal sensor placement scheme. The proposed method can be applied to high-rise buildings for seismic performance assessment.展开更多
The actuator and sensor placement problem for active vibration control of large cable net structures is investigated in this paper.Since the structures exhibit closely spaced modes in the range of low frequencies,the ...The actuator and sensor placement problem for active vibration control of large cable net structures is investigated in this paper.Since the structures exhibit closely spaced modes in the range of low frequencies,the number of modes to be considered is quite large after modal truncation,while only a limited number of actuators and sensors are to be placed.This makes it hard to determine the actuator and sensor locations with the existing placement methods in the literature such as the methods based on the controllability/observability grammian.To deal with this issue,an actuator and sensor placement method based on singular value decompositions(SVD)of the input and output matrices is proposed,which guarantees the modal controllability and observability of the system.The effectiveness of the SVD based method is verified through numerical simulations in which comparisons are conducted between randomly-chosen locations and the optimal ones obtained by a genetic algorithm.展开更多
A new method is presented for prioritizing sensor locations for structural health monitoring (SHM). In view of the needs of SHM and damage detection,sensor locations are optimized for the purpose of both sensitivity f...A new method is presented for prioritizing sensor locations for structural health monitoring (SHM). In view of the needs of SHM and damage detection,sensor locations are optimized for the purpose of both sensitivity for local damages and independence of the target mode. However,the two different optimization criterions lead to an inconsistency of the optimal result. Considering the structural response changes that result from damage,the relationship between the structural response and damage is deduced from the structural motion equation by a quasi-analytical mode. Based on the harmony between damage identifiability and mode observability,an object function is set up,including the information of mode independence and damage sensitivity. Utilizing the technique of singular value decomposition,an interior algorithm for the optimum sensor placement is proposed with the multiple objective criterions of minimizing the condition number of coefficient matrix and maximizing the fisher information matrix. A numerical example shows that this approach can effectively avoid the contradiction between the two different optimization criterions. Comparing with the result of single object,the result of damage detection from the optical sensor locations is much more accurate.展开更多
The process of optimized placement of long-term health monitoring sensors for large bridges generally begins with finite element models, but there will arise great discrepancies between theoretically-calculated result...The process of optimized placement of long-term health monitoring sensors for large bridges generally begins with finite element models, but there will arise great discrepancies between theoretically-calculated results and actual measurements.Therefore, rectified finite element models need to be rectified by virtue of model rectifying technology. Firstly, the result of construction monitoring and finished state load test is used to real-time modification of finite element model. Subsequently, an accurate finite element model is established. Secondly, the optimizing the layout of sensor with following orthogonality guarantees orthogonal property and linear independence for the measured data. Lastly, the effectiveness and feasibility of method in the paper is tested by real-time modifying finite element model and optimizing the layout of sensor for Nujiang Bridge.展开更多
A methodology, termed estimation error minimization(EEM) method, was proposed to determine the optimal number and locations of sensors so as to better estimate the vibration response of the entire structure. Utilizing...A methodology, termed estimation error minimization(EEM) method, was proposed to determine the optimal number and locations of sensors so as to better estimate the vibration response of the entire structure. Utilizing the limited sensor measurements, the entire structure response can be estimated based on the system equivalent reduction-expansion process(SEREP) method. In order to compare the capability of capturing the structural vibration response with other optimal sensor placement(OSP) methods, the effective independence(EI) method, modal kinetic energy(MKE) method and modal assurance criterion(MAC) method, were also investigated. A statistical criterion, root mean square error(RMSE), was employed to assess the magnitude of the estimation error between the real response and the estimated response. For investigating the effectiveness and accuracy of the above OSP methods, a 31-bar truss structure is introduced as a simulation example. The analysis results show that both the maximum and mean of the RMSE value obtained from the EEM method are smaller than those from other OSP methods, which indicates that the optimal sensor configuration obtained from the EEM method can provide a more accurate estimation of the entire structure response compared with the EI, MKE and MAC methods.展开更多
Civil engineering structures are constructed for strength, serviceability and durability. The structures thus constructed involve huge investment and labour work. In order to protect the structure from various damages...Civil engineering structures are constructed for strength, serviceability and durability. The structures thus constructed involve huge investment and labour work. In order to protect the structure from various damages, periodic monitoring of structures is necessary. Hence Structural Health Monitoring (SHM) plays a vital role in diagnosing the state of the structure at every moment during its life period. For this purpose, sensors are deployed in the structures for its efficient health monitoring. Sensors cannot be deployed at random locations of the structure. They have to be located at those points which reflect the damage. In this study, a 3-storey and a 4-storey building are taken and Modal Strain Energy (MSE) is used for finding the initial locations of sensors. The number of sensors obtained is then optimized using Genetic Algorithm (GA) technique. Finally damages are induced in certain locations of the structure and a damage detection technique called as “Flexibility Matrix Based Technique (FMBT)” is introduced for damage localization in the structure.展开更多
The capacity and size of hydro-generator units are increasing with the rapid development of hydroelectric enterprises, and the vibration of the powerhouse structure has increasingly become a major problem. Field testi...The capacity and size of hydro-generator units are increasing with the rapid development of hydroelectric enterprises, and the vibration of the powerhouse structure has increasingly become a major problem. Field testing is an important method for research on dynamic identification and vibration mechanisms. Research on optimal sensor placement has become a very important topic due to the need to obtain effective testing information from limited test resources. To overcome inadequacies of the present methods, this paper puts forward the triaxial effective independence driving-point residue （EfI3-DPR3） method for optimal sensor placement. The Efl3-DPR3 method can incorporate both the maximum triaxial modal kinetic energy and linear independence of the triaxial target modes at the selected nodes. It was applied to the optimal placement oftriaxial sensors for vibration testing in a hydropower house, and satisfactory results were obtained. This method can provide some guidance for optimal placement of triaxial sensors of underground powerhouses.展开更多
We present a novel paradigm of sensor placement concerning data precision and estimation.Multiple abstract sensors are used to measure a quantity of a moving target in the scenario of a wireless sensor network.These s...We present a novel paradigm of sensor placement concerning data precision and estimation.Multiple abstract sensors are used to measure a quantity of a moving target in the scenario of a wireless sensor network.These sensors can cooperate with each other to obtain a precise estimate of the quantity in a real-time manner.We consider a problem on planning a minimum-cost scheme of sensor placement with desired data precision and resource consumption.Measured data is modeled as a Gaussian random variable with a changeable variance.A gird model is used to approximate the problem.We solve the problem with a heuristic algorithm using branch-and-bound method and tabu search.Our experiments demonstrate that the algorithm is correct in a certain tolerance,and it is also efficient and scalable.展开更多
In this paper, a method for sensor placement to improve the placement quality based on angle of arrival of signal in a specific area is proposed. The installation place of sensors may be constrained with specified bou...In this paper, a method for sensor placement to improve the placement quality based on angle of arrival of signal in a specific area is proposed. The installation place of sensors may be constrained with specified boundaries. In this me-thod, the criterion of maximum quality of placement is the Cramer-Rao bound. The generalized pattern search as an effective method is used to maximize error bound of the placement problem by angle of arrival. Better results are ob-tained in comparison with results of genetic algorithm. The derived results are compared from two aspects of run time and result quality.展开更多
Structural health monitoring(SHM) provides an effective approach to ensure the safety of structures.However,with the restriction of the cost of sensor system and data processing,only a small number of sensors could be...Structural health monitoring(SHM) provides an effective approach to ensure the safety of structures.However,with the restriction of the cost of sensor system and data processing,only a small number of sensors could be available in the health monitoring system(HMS).In order to obtain the best identification of structural characteristics,optimal sensor placement(OSP) becomes an inevitable task in the design of HMS.This paper introduces the process for determining the OSP in HMS of a suspension bridge,in which four different OSP methods have been investigated,including the effective independence(EI) method,the effective independence driving-point residue(EFI-DPR) method,the minimized modal assurance criterion(minMAC) method and the principal subset selection-based extended EI(PSS-EI) method.Then,three criteria,which are modal assurance matrix(MAC),condition number(CN) of mode shape matrix and determinant of Fisher information matrix(FIM),were employed to evaluate the effect of the OSP methods respectively.The result showed that the PSS-EI method developed has the ability to guarantee the highest determinant of FIM,a relatively small off-diagonal term of MAC and agreeable CN,as well as the deployment of sensors in a uniform and symmetric fashion for the studied bridge.Finally,the scheme obtained by PSS-EI was adopted in the HMS.展开更多
This paper presents an interval effective independence method for optimal sensor placement, which contains uncertain structural information. To overcome the lack of insufficient statistic description of uncertain para...This paper presents an interval effective independence method for optimal sensor placement, which contains uncertain structural information. To overcome the lack of insufficient statistic description of uncertain parameters, this paper treats uncertainties as non-probability intervals. Based on the iterative process of classical effective independence method, the proposed study considers the eliminating steps with uncertain cases. Therefore, this method with Fisher information matrix is extended to interval numbers, which could conform to actual engineering. As long as we know the bounds of uncertainties, the interval Fisher information matrix could be obtained conveniently by interval analysis technology. Moreover, due to the definition and calculation of the interval relationship, the possibilities of eliminating candidate sensors in each iterative process and the final layout of sensor placement are both presented in this paper. Finally, two numerical examples, including a five-storey shear structure and a truss structure are proposed respectively in this paper. Compared with Monte Carlo simulation, both of them can indicate the veracity of the interval effective independence method.展开更多
Complete temperature field estimation from limited local measurements is widely desired in many industrial and scientific applications of thermal engineering. Since the sensor configuration dominates the reconstructio...Complete temperature field estimation from limited local measurements is widely desired in many industrial and scientific applications of thermal engineering. Since the sensor configuration dominates the reconstruction performance, some progress has been made in designing sensor placement methods. But these approaches remain to be improved in terms of both accuracy and efficiency due to the lack of comprehensive schemes and efficient optimization algorithms. In this work, we develop a datadriven sensor placement framework for thermal field reconstruction. Specifically, we first tailor the low-dimensional model from the prior thermal maps to represent the high-dimensional temperature distribution states by virtue of proper orthogonal decomposition technique. Then, on such subspace, a recursive greedy algorithm with determinant maximization as the objective function is developed to optimize the sensor placement configuration. Furthermore, we find that the same sensor configuration can be yielded faster by the standard procedures of column-pivoted QR factorization, which allows concise software implementation with readily available function packages. When the sensor locations are determined, we advocate using the databased closed-form estimator to minimize the reconstruction error. Real-time thermal monitoring on the multi-core processor is employed as the case to demonstrate the effectiveness of the proposed methods for thermal field reconstruction. Extensive evaluations are conducted on simulation or experimental datasets of three processors with different architectures. The results show that our method achieves state-of-the-art reconstruction performance while possessing the lowest computational complexity when compared with the existing methods.展开更多
为以较小的成本获取全面的艉部振动信息,以某自航模型为研究对象,采用局部线性嵌入(Locally Linear Embedding,LLE)对其艉部振动测点进行优化设计,获取了不同工况下振动测点重要度排序,并通过与传统的频谱分析方法对比,验证了优化结果...为以较小的成本获取全面的艉部振动信息,以某自航模型为研究对象,采用局部线性嵌入(Locally Linear Embedding,LLE)对其艉部振动测点进行优化设计,获取了不同工况下振动测点重要度排序,并通过与传统的频谱分析方法对比,验证了优化结果的合理性。结果表明,轴承部位作为桨轴激励传递的主要通道,具有较高的优先级,可对船体测点按照测点重要程度排序,选取合适的测点,进而为后续试验提供基础。展开更多
This paper presents a Torque Sharing Function(TSF)control of Switched Reluctance Machines(SRMs)with different current sensor placements to reconstruct the phase currents.TSF requires precise phase current information ...This paper presents a Torque Sharing Function(TSF)control of Switched Reluctance Machines(SRMs)with different current sensor placements to reconstruct the phase currents.TSF requires precise phase current information to ensure accurate torque control.Two proposed methods with different chopping transistors or a new PWM implementation require four or two current sensors to replace the current sensors on each phase regardless of the phase number.For both approaches,the actual phase current can be easily extracted during the single phase conducting region.However,how to separate the incoming and outgoing phase current values during the commutation region is the difficult issue to deal with.In order to derive these two adjacent currents,the explanations and comparisons of two proposed methods are described.Their effectiveness is verified by experimental results on a four-phase 8/6 SRM.Finally,the approach with a new PWM implementation is selected,which requires only two current sensors for reducing the number of sensors.The control system can be more compact and cheaper.展开更多
基金Projects 2005AA133070 supported by the National High Technology Research and Development Program of China[2005]688 and [2005]555 by the Devel-opment Fund for Electronic and Information Industry
文摘In order to provide a theoretical basis for methane sensor placement in the vertical direction of a tunnel,the software Fluent was used to simulate methane distribution. A geometric roadway model was established and divided by grids. Methane distribution in both level and vertical sections was simulated using a realizable k-ε model with the Fluent software according to a conservation equation in a turbulent state,a turbulent kinetic energy equation and a turbulent dissipation rate equation. The realizable k-ε model and the Fluent software were used to simulate methane distribution according to the principle of the conservation equation in a state of turbulent flow. The results show that after overflow-ing,a methane level with a certain thickness is formed. Methane density curves at three specific levels were internally consistent and methane density at higher levels is denser than that at lower levels. Methane distribution becomes thinner in the direction of wind and methane in the vertical direction becomes uniform if wind speed is high. The distance be-tween sensors and roof should be less than 300 mm which is in agreement with mine safety regulations.
基金The Hong Kong Polytechnic University through the group project "Fundamentals of Earthquake Engineering for Hong Kong"(4-ZZCD)the collaborative research project with Beijing University of Technology(4-ZZGD)
文摘Estimation of lateral displacement and acceleration responses is essential to assess safety and serviceability of high-rise buildings under dynamic loadings including earthquake excitations. However, the measurement information from the limited number of sensors installed in a building structure is often insufficient for the complete structural performance assessment. An integrated multi-type sensor placement and response reconstruction method has thus been proposed by the authors to tackle this problem. To validate the feasibility and effectiveness of the proposed method, an experimental investigation using a cantilever beam with multi-type sensors is performed and reported in this paper. The experimental setup is first introduced. The finite element modelling and model updating of the cantilever beam are then performed. The optimal sensor placement for the best response reconstruction is determined by the proposed method based on the updated FE model of the beam. After the sensors are installed on the physical cantilever beam, a number of experiments are carried out. The responses at key locations are reconstructed and compared with the measured ones. The reconstructed responses achieve a good match with the measured ones, manifesting the feasibility and effectiveness of the proposed method. Besides, the proposed method is also examined for the cases of different excitations and unknown excitation, and the results prove the proposed method to be robust and effective. The superiority of the optimized sensor placement scheme is finally demonstrated through comparison with two other different sensor placement schemes： the accelerometer-only scheme and non-optimal sensor placement scheme. The proposed method can be applied to high-rise buildings for seismic performance assessment.
基金National Natural Science Foundation of China(11290153)。
文摘The actuator and sensor placement problem for active vibration control of large cable net structures is investigated in this paper.Since the structures exhibit closely spaced modes in the range of low frequencies,the number of modes to be considered is quite large after modal truncation,while only a limited number of actuators and sensors are to be placed.This makes it hard to determine the actuator and sensor locations with the existing placement methods in the literature such as the methods based on the controllability/observability grammian.To deal with this issue,an actuator and sensor placement method based on singular value decompositions(SVD)of the input and output matrices is proposed,which guarantees the modal controllability and observability of the system.The effectiveness of the SVD based method is verified through numerical simulations in which comparisons are conducted between randomly-chosen locations and the optimal ones obtained by a genetic algorithm.
基金Sponsored by the National Key Natural Science Foundation of China(Grant No.50439010)Key Project of Chinese Ministry of Education(Grant No.305003)
文摘A new method is presented for prioritizing sensor locations for structural health monitoring (SHM). In view of the needs of SHM and damage detection,sensor locations are optimized for the purpose of both sensitivity for local damages and independence of the target mode. However,the two different optimization criterions lead to an inconsistency of the optimal result. Considering the structural response changes that result from damage,the relationship between the structural response and damage is deduced from the structural motion equation by a quasi-analytical mode. Based on the harmony between damage identifiability and mode observability,an object function is set up,including the information of mode independence and damage sensitivity. Utilizing the technique of singular value decomposition,an interior algorithm for the optimum sensor placement is proposed with the multiple objective criterions of minimizing the condition number of coefficient matrix and maximizing the fisher information matrix. A numerical example shows that this approach can effectively avoid the contradiction between the two different optimization criterions. Comparing with the result of single object,the result of damage detection from the optical sensor locations is much more accurate.
基金Funded by the Special Found of the Ministry of Education for Doctor Station Subject(No.20115522110001)
文摘The process of optimized placement of long-term health monitoring sensors for large bridges generally begins with finite element models, but there will arise great discrepancies between theoretically-calculated results and actual measurements.Therefore, rectified finite element models need to be rectified by virtue of model rectifying technology. Firstly, the result of construction monitoring and finished state load test is used to real-time modification of finite element model. Subsequently, an accurate finite element model is established. Secondly, the optimizing the layout of sensor with following orthogonality guarantees orthogonal property and linear independence for the measured data. Lastly, the effectiveness and feasibility of method in the paper is tested by real-time modifying finite element model and optimizing the layout of sensor for Nujiang Bridge.
基金Project(2011CB013804)supported by the National Basic Research Program of China
文摘A methodology, termed estimation error minimization(EEM) method, was proposed to determine the optimal number and locations of sensors so as to better estimate the vibration response of the entire structure. Utilizing the limited sensor measurements, the entire structure response can be estimated based on the system equivalent reduction-expansion process(SEREP) method. In order to compare the capability of capturing the structural vibration response with other optimal sensor placement(OSP) methods, the effective independence(EI) method, modal kinetic energy(MKE) method and modal assurance criterion(MAC) method, were also investigated. A statistical criterion, root mean square error(RMSE), was employed to assess the magnitude of the estimation error between the real response and the estimated response. For investigating the effectiveness and accuracy of the above OSP methods, a 31-bar truss structure is introduced as a simulation example. The analysis results show that both the maximum and mean of the RMSE value obtained from the EEM method are smaller than those from other OSP methods, which indicates that the optimal sensor configuration obtained from the EEM method can provide a more accurate estimation of the entire structure response compared with the EI, MKE and MAC methods.
文摘Civil engineering structures are constructed for strength, serviceability and durability. The structures thus constructed involve huge investment and labour work. In order to protect the structure from various damages, periodic monitoring of structures is necessary. Hence Structural Health Monitoring (SHM) plays a vital role in diagnosing the state of the structure at every moment during its life period. For this purpose, sensors are deployed in the structures for its efficient health monitoring. Sensors cannot be deployed at random locations of the structure. They have to be located at those points which reflect the damage. In this study, a 3-storey and a 4-storey building are taken and Modal Strain Energy (MSE) is used for finding the initial locations of sensors. The number of sensors obtained is then optimized using Genetic Algorithm (GA) technique. Finally damages are induced in certain locations of the structure and a damage detection technique called as “Flexibility Matrix Based Technique (FMBT)” is introduced for damage localization in the structure.
基金supported by the National Natural Science Foundation of China (Grant No. 50909072)the New Teachers' Fund for Doctor Station, the Ministry of Education of China (Grant No. 20090032120082)the Communication Research Item for the West Area, the Ministry of Communications of China (Grant No. 2009328000084)
文摘The capacity and size of hydro-generator units are increasing with the rapid development of hydroelectric enterprises, and the vibration of the powerhouse structure has increasingly become a major problem. Field testing is an important method for research on dynamic identification and vibration mechanisms. Research on optimal sensor placement has become a very important topic due to the need to obtain effective testing information from limited test resources. To overcome inadequacies of the present methods, this paper puts forward the triaxial effective independence driving-point residue （EfI3-DPR3） method for optimal sensor placement. The Efl3-DPR3 method can incorporate both the maximum triaxial modal kinetic energy and linear independence of the triaxial target modes at the selected nodes. It was applied to the optimal placement oftriaxial sensors for vibration testing in a hydropower house, and satisfactory results were obtained. This method can provide some guidance for optimal placement of triaxial sensors of underground powerhouses.
基金Supported of Project of Fok Ying Tong Education Foundation(No.104030)Supported of Key Project of National Natural Science of Foundation of China(No.70531020)+2 种基金Supported of Project of New Century Excellent Talent(No.NCET-06-0382)Supported of Key Project of Education Ministry of China(No.306023)Supported of Project of Doctoral Education(20070247075)
文摘We present a novel paradigm of sensor placement concerning data precision and estimation.Multiple abstract sensors are used to measure a quantity of a moving target in the scenario of a wireless sensor network.These sensors can cooperate with each other to obtain a precise estimate of the quantity in a real-time manner.We consider a problem on planning a minimum-cost scheme of sensor placement with desired data precision and resource consumption.Measured data is modeled as a Gaussian random variable with a changeable variance.A gird model is used to approximate the problem.We solve the problem with a heuristic algorithm using branch-and-bound method and tabu search.Our experiments demonstrate that the algorithm is correct in a certain tolerance,and it is also efficient and scalable.
文摘In this paper, a method for sensor placement to improve the placement quality based on angle of arrival of signal in a specific area is proposed. The installation place of sensors may be constrained with specified boundaries. In this me-thod, the criterion of maximum quality of placement is the Cramer-Rao bound. The generalized pattern search as an effective method is used to maximize error bound of the placement problem by angle of arrival. Better results are ob-tained in comparison with results of genetic algorithm. The derived results are compared from two aspects of run time and result quality.
基金supported by the National Key Technology R&D Program in the 12th Five-year Plan of China (Grant No. 2011BAK02B01)
文摘Structural health monitoring(SHM) provides an effective approach to ensure the safety of structures.However,with the restriction of the cost of sensor system and data processing,only a small number of sensors could be available in the health monitoring system(HMS).In order to obtain the best identification of structural characteristics,optimal sensor placement(OSP) becomes an inevitable task in the design of HMS.This paper introduces the process for determining the OSP in HMS of a suspension bridge,in which four different OSP methods have been investigated,including the effective independence(EI) method,the effective independence driving-point residue(EFI-DPR) method,the minimized modal assurance criterion(minMAC) method and the principal subset selection-based extended EI(PSS-EI) method.Then,three criteria,which are modal assurance matrix(MAC),condition number(CN) of mode shape matrix and determinant of Fisher information matrix(FIM),were employed to evaluate the effect of the OSP methods respectively.The result showed that the PSS-EI method developed has the ability to guarantee the highest determinant of FIM,a relatively small off-diagonal term of MAC and agreeable CN,as well as the deployment of sensors in a uniform and symmetric fashion for the studied bridge.Finally,the scheme obtained by PSS-EI was adopted in the HMS.
基金supported by the National Natural Science Foundation of China(Grant No.11502278)
文摘This paper presents an interval effective independence method for optimal sensor placement, which contains uncertain structural information. To overcome the lack of insufficient statistic description of uncertain parameters, this paper treats uncertainties as non-probability intervals. Based on the iterative process of classical effective independence method, the proposed study considers the eliminating steps with uncertain cases. Therefore, this method with Fisher information matrix is extended to interval numbers, which could conform to actual engineering. As long as we know the bounds of uncertainties, the interval Fisher information matrix could be obtained conveniently by interval analysis technology. Moreover, due to the definition and calculation of the interval relationship, the possibilities of eliminating candidate sensors in each iterative process and the final layout of sensor placement are both presented in this paper. Finally, two numerical examples, including a five-storey shear structure and a truss structure are proposed respectively in this paper. Compared with Monte Carlo simulation, both of them can indicate the veracity of the interval effective independence method.
基金This work was supported by the Foundation for Innovative Research Groups of the National Natural Science Foundation of China(Grant No.51521004)。
文摘Complete temperature field estimation from limited local measurements is widely desired in many industrial and scientific applications of thermal engineering. Since the sensor configuration dominates the reconstruction performance, some progress has been made in designing sensor placement methods. But these approaches remain to be improved in terms of both accuracy and efficiency due to the lack of comprehensive schemes and efficient optimization algorithms. In this work, we develop a datadriven sensor placement framework for thermal field reconstruction. Specifically, we first tailor the low-dimensional model from the prior thermal maps to represent the high-dimensional temperature distribution states by virtue of proper orthogonal decomposition technique. Then, on such subspace, a recursive greedy algorithm with determinant maximization as the objective function is developed to optimize the sensor placement configuration. Furthermore, we find that the same sensor configuration can be yielded faster by the standard procedures of column-pivoted QR factorization, which allows concise software implementation with readily available function packages. When the sensor locations are determined, we advocate using the databased closed-form estimator to minimize the reconstruction error. Real-time thermal monitoring on the multi-core processor is employed as the case to demonstrate the effectiveness of the proposed methods for thermal field reconstruction. Extensive evaluations are conducted on simulation or experimental datasets of three processors with different architectures. The results show that our method achieves state-of-the-art reconstruction performance while possessing the lowest computational complexity when compared with the existing methods.
文摘为以较小的成本获取全面的艉部振动信息,以某自航模型为研究对象,采用局部线性嵌入(Locally Linear Embedding,LLE)对其艉部振动测点进行优化设计,获取了不同工况下振动测点重要度排序,并通过与传统的频谱分析方法对比,验证了优化结果的合理性。结果表明,轴承部位作为桨轴激励传递的主要通道,具有较高的优先级,可对船体测点按照测点重要程度排序,选取合适的测点,进而为后续试验提供基础。
基金The test bench was supported by The Future Planning(NRF-2016H1D5A1910536)“Human Resources Program in Energy Technology”of the Korea Institute of Energy Technology Evaluation and Planning(KETEP),granted financial resource from the Ministry of Trade,Industry&Energy,Republic of Korea.(No.20164010200940)The authors would like to thank FONDS DAVID ET ALICE VAN BUUREN and FONDATION JAUMOTTE-DEMOULIN for the funding“Prix Van Buuren-Jaumotte-Demoulin”.
文摘This paper presents a Torque Sharing Function(TSF)control of Switched Reluctance Machines(SRMs)with different current sensor placements to reconstruct the phase currents.TSF requires precise phase current information to ensure accurate torque control.Two proposed methods with different chopping transistors or a new PWM implementation require four or two current sensors to replace the current sensors on each phase regardless of the phase number.For both approaches,the actual phase current can be easily extracted during the single phase conducting region.However,how to separate the incoming and outgoing phase current values during the commutation region is the difficult issue to deal with.In order to derive these two adjacent currents,the explanations and comparisons of two proposed methods are described.Their effectiveness is verified by experimental results on a four-phase 8/6 SRM.Finally,the approach with a new PWM implementation is selected,which requires only two current sensors for reducing the number of sensors.The control system can be more compact and cheaper.
