It is important for the safety of transmission system to accurately calculate single-phase earth fault current distribution.Features of double sided elimination method were illustrated.Quantitative calculation of sing...It is important for the safety of transmission system to accurately calculate single-phase earth fault current distribution.Features of double sided elimination method were illustrated.Quantitative calculation of single-phase earth fault current distribution and case verification were accomplished by using the loop method.Influences of some factors,such as single-phase earth fault location and ground resistance of poles,on short-circuit current distribution were discussed.Results show that:1) results of the loop method conform to those of double sided elimination method;2) the fault location hardly influences macro-distribution of short-circuit current.However,current near fault location is evidently influenced;and 3) the short-circuit current distribution is not so sensitive to the ground resistance of poles.展开更多
Electric field measurement holds immense significance in various domains.The power supply and signal acquisition units of the sensor may be coupled with ground wire interference,which could result in reduced measureme...Electric field measurement holds immense significance in various domains.The power supply and signal acquisition units of the sensor may be coupled with ground wire interference,which could result in reduced measurement accuracy.Moreover,this problem is often ignored by researchers.This paper investigated the origin of ground coupling interference in electric field sensors and its impact on measurement accuracy.A miniature undistorted electric field sensor with wireless transmission was compared with existing D-dot,microelectromechanical systems(MEMS),and optical sensors.The results indicate that MEMS and D-dot exhibit diminished accuracy in measuring electric fields under uniform conditions,owing to interference from ground wires.In the case of transmission lines with non-uniform conditions,the wireless sensor exhibited a measurement error of 5%,whereas the optical sensor showed an error rate of approximately 8%.However,the D-dot sensor displayed a measurement error exceeding 50%,whereas the MEMS sensor yielded an error as high as 150%.This means that the wireless sensor isolates the ground-coupled interference signal and realizes the distortion-free measurement of the electric field.The wireless sensors will find extensive applications in new power systems for intelligent equipment status perception,fault warning,and other scenarios.展开更多
Today the entire globe is shrouded in an inefficient three-phase system. There is however an efficient single-wire system. To use the single wire method, three phase systems can be converted to triple one wire systems.
采用熔盐法制备α-Al_(2)O_(3),采用硅烷偶联剂γ-氨丙基三乙氧基硅烷(KH550)对α-Al_(2)O_(3)进行表面改性,得到KH-α-Al_(2)O_(3)。以低密度聚乙烯(LDPE)为基体、不同的α-Al_(2)O_(3)为添加剂,制备α-Al_(2)O_(3)/XLPE和KH-α-Al_(2)...采用熔盐法制备α-Al_(2)O_(3),采用硅烷偶联剂γ-氨丙基三乙氧基硅烷(KH550)对α-Al_(2)O_(3)进行表面改性,得到KH-α-Al_(2)O_(3)。以低密度聚乙烯(LDPE)为基体、不同的α-Al_(2)O_(3)为添加剂,制备α-Al_(2)O_(3)/XLPE和KH-α-Al_(2)O_(3)/XLPE接地线绝缘材料。对α-Al_(2)O_(3)和KH-α-Al_(2)O_(3)的晶体结构、微观结构以及基团进行分析,考察不同α-Al_(2)O_(3)含量对α-Al_(2)O_(3)/XLPE接地线绝缘材料电学性能和热学性能的影响。结果表明:熔盐法制备的α-Al_(2)O_(3)是具有六方结构、结晶度高、直径5~10μm的不规则圆片,KH550的改性不会造成α-Al_(2)O_(3)结晶度的变化。KH-α-Al_(2)O_(3)在KH-α-Al_(2)O_(3)/XLPE接地线绝缘材料中沿材料厚度方向排列,且分散更为均匀,有利于抑制电荷在基体中的传输。KH-α-Al_(2)O_(3)有利于提高XLPE的直流击穿场强和直流电导率。当KH-α-Al_(2)O_(3)的添加质量分数为1.5%时,KH-α-Al_(2)O_(3)/XLPE的直流击穿场强达到320 k V/mm,电导率为1.043×10^(-13)S/m。KH-α-Al_(2)O_(3)的引入使XLPE基体和KH-α-Al_(2)O_(3)之间的界面产生一定数量的陷阱,有效实现了对注入电荷的抑制。KH-α-Al_(2)O_(3)可以明显降低XLPE的热失重速率,提高KH-α-Al_(2)O_(3)/XLPE接地线绝缘材料热稳定性。当KH-α-Al_(2)O_(3)的质量分数达到1.5%时,分解温度升高至475.44℃,90℃条件下的导热系数从0.390 W/(m·K)增加到0.545 W/(m·K)。展开更多
文摘It is important for the safety of transmission system to accurately calculate single-phase earth fault current distribution.Features of double sided elimination method were illustrated.Quantitative calculation of single-phase earth fault current distribution and case verification were accomplished by using the loop method.Influences of some factors,such as single-phase earth fault location and ground resistance of poles,on short-circuit current distribution were discussed.Results show that:1) results of the loop method conform to those of double sided elimination method;2) the fault location hardly influences macro-distribution of short-circuit current.However,current near fault location is evidently influenced;and 3) the short-circuit current distribution is not so sensitive to the ground resistance of poles.
基金supported in part by the National Key Research and Development Program of China under Grant 2022YFB3206800in part by the National Natural Science Foundation of China under Grant 52125703.
文摘Electric field measurement holds immense significance in various domains.The power supply and signal acquisition units of the sensor may be coupled with ground wire interference,which could result in reduced measurement accuracy.Moreover,this problem is often ignored by researchers.This paper investigated the origin of ground coupling interference in electric field sensors and its impact on measurement accuracy.A miniature undistorted electric field sensor with wireless transmission was compared with existing D-dot,microelectromechanical systems(MEMS),and optical sensors.The results indicate that MEMS and D-dot exhibit diminished accuracy in measuring electric fields under uniform conditions,owing to interference from ground wires.In the case of transmission lines with non-uniform conditions,the wireless sensor exhibited a measurement error of 5%,whereas the optical sensor showed an error rate of approximately 8%.However,the D-dot sensor displayed a measurement error exceeding 50%,whereas the MEMS sensor yielded an error as high as 150%.This means that the wireless sensor isolates the ground-coupled interference signal and realizes the distortion-free measurement of the electric field.The wireless sensors will find extensive applications in new power systems for intelligent equipment status perception,fault warning,and other scenarios.
文摘Today the entire globe is shrouded in an inefficient three-phase system. There is however an efficient single-wire system. To use the single wire method, three phase systems can be converted to triple one wire systems.
文摘采用熔盐法制备α-Al_(2)O_(3),采用硅烷偶联剂γ-氨丙基三乙氧基硅烷(KH550)对α-Al_(2)O_(3)进行表面改性,得到KH-α-Al_(2)O_(3)。以低密度聚乙烯(LDPE)为基体、不同的α-Al_(2)O_(3)为添加剂,制备α-Al_(2)O_(3)/XLPE和KH-α-Al_(2)O_(3)/XLPE接地线绝缘材料。对α-Al_(2)O_(3)和KH-α-Al_(2)O_(3)的晶体结构、微观结构以及基团进行分析,考察不同α-Al_(2)O_(3)含量对α-Al_(2)O_(3)/XLPE接地线绝缘材料电学性能和热学性能的影响。结果表明:熔盐法制备的α-Al_(2)O_(3)是具有六方结构、结晶度高、直径5~10μm的不规则圆片,KH550的改性不会造成α-Al_(2)O_(3)结晶度的变化。KH-α-Al_(2)O_(3)在KH-α-Al_(2)O_(3)/XLPE接地线绝缘材料中沿材料厚度方向排列,且分散更为均匀,有利于抑制电荷在基体中的传输。KH-α-Al_(2)O_(3)有利于提高XLPE的直流击穿场强和直流电导率。当KH-α-Al_(2)O_(3)的添加质量分数为1.5%时,KH-α-Al_(2)O_(3)/XLPE的直流击穿场强达到320 k V/mm,电导率为1.043×10^(-13)S/m。KH-α-Al_(2)O_(3)的引入使XLPE基体和KH-α-Al_(2)O_(3)之间的界面产生一定数量的陷阱,有效实现了对注入电荷的抑制。KH-α-Al_(2)O_(3)可以明显降低XLPE的热失重速率,提高KH-α-Al_(2)O_(3)/XLPE接地线绝缘材料热稳定性。当KH-α-Al_(2)O_(3)的质量分数达到1.5%时,分解温度升高至475.44℃,90℃条件下的导热系数从0.390 W/(m·K)增加到0.545 W/(m·K)。
