A systematic methodology for solving the inverse dynamics of the Delta robot is presented.First,the inverse kinematics is solved based on the vector method.A new form of the Jacobi matrix formulized by the vectors is ...A systematic methodology for solving the inverse dynamics of the Delta robot is presented.First,the inverse kinematics is solved based on the vector method.A new form of the Jacobi matrix formulized by the vectors is obtained so the three types kinematics singularities namely inverse, direct and combined types, can be identified with the physical meaning.Then based on the principle of virtual work, a methodology for driving the dynamical equations of motion is developed.Meanwhile the whole actuating torques, the torques caused by the gravity, the velocity and the acceleration are computed respectively in the numerical example. Results show that torque caused by the acceleration term is much bigger than the other two terms.This approach leads to efficient algorithms since the constraint forces and moments of the robot system have been eliminated from the equations of motion and there is no differential equation for the whole procedure when the principle of virtual work is applied to solving the inverse dynamical problem.展开更多
Overtaking accidents caused by improper operations performed by a driver occur frequently. However, most stud?ies on overtaking safety have neglected research into driver control input. A novel method is proposed to o...Overtaking accidents caused by improper operations performed by a driver occur frequently. However, most stud?ies on overtaking safety have neglected research into driver control input. A novel method is proposed to obtain the driver control input during the overtaking process. Meanwhile, to improve the safety of overtaking, two types of safe distances, and the time of the overtaking are considered. Path constraints are established when considering the two types of safe distances. An optimal control model is established to solve the minimum time maneuver under multiple constraints. Using the Gauss pseudospectral method, the optimal control problem is converted into a nonlinear pro?gramming problem, which is then solved through sequential quadratic programming(SQP). In addition, the e ective?ness of the proposed method is verified based on the results of a Carsim simulation. The simulation results show that by adopting an inverse dynamics method to solve the manipulation problem of the vehicle’s minimum overtaking time, the manipulation capability of a vehicle in completing an overtaking safely within the minimum time can be obtained. This method can provide a reference for research into the active safety of manned and unmanned vehicles.展开更多
Mechanical assembly has its own dynamic quality directly affecting the dynamic quality of whole product and should be considered in quality inspection and estimation of mechanical assembly. Based on functional relatio...Mechanical assembly has its own dynamic quality directly affecting the dynamic quality of whole product and should be considered in quality inspection and estimation of mechanical assembly. Based on functional relations between dynamic characteristics involved in mechanical assembly, the effects of assembling process on dynamic characteristics of substructural components of an assembly system are investigated by substructuring analysis. Assembly-coupling dynamic stiffness is clarified as the dominant factor of the effects and can be used as a quantitative measure of assembly dynamic quality. Two computational schemes using frequency response functions（FRFs） to determine the stiffness are provided and discussed by inverse substructuring analysis, including their applicable conditions and implementation procedure in application. Eigenvalue analysis on matrix-ratios of FRFs before and after assembling is employed and well validates the analytical outcomes and the schemes via both a lumped-parameter model and its analogic experimental counterpart. Applying the two schemes to inspect the dynamic quality provides the message of dynamic performance of the assembly system, and therefore improves conventional quality inspection and estimation of mechanical assembly in completeness.展开更多
It is a complicated nonlinear controlling problem to conduct a two-dimensional trajectory correction of rockets.By establishing the aerodynamic correction force mathematical model of rockets on nose cone swinging,the ...It is a complicated nonlinear controlling problem to conduct a two-dimensional trajectory correction of rockets.By establishing the aerodynamic correction force mathematical model of rockets on nose cone swinging,the linear control is realized by the dynamic inverse nonlinear controlling theory and the three-time-scale separation method.The control ability and the simulation results are also tested and verified.The results show that the output responses of system track the expected curve well and the error is controlled in a given margin.The maximum correction is about±314 m in the lengthwise direction and±1 212 m in the crosswise direction from the moment of 5 s to the drop-point time when the angle of fire is 55°.Thus,based on the dynamic inverse control of feedback linearization,the trajectory correction capability of nose cone swinging can satisfy the requirements of two-dimensional ballistic correction,and the validity and effectiveness of the method are proved.展开更多
This paper considers a concrete stochastic nonlinear system with stochastic unmeasurable inverse dynamics. Motivated by the concept of integral input-to-state stability （iISS） in deterministic systems and stochastic...This paper considers a concrete stochastic nonlinear system with stochastic unmeasurable inverse dynamics. Motivated by the concept of integral input-to-state stability （iISS） in deterministic systems and stochastic input-to-state stability （SISS） in stochastic systems, a concept of stochastic integral input-to-state stability （SiISS） using Lyapunov functions is first introduced. A constructive strategy is proposed to design a dynamic output feedback control law, which drives the state to the origin almost surely while keeping all other closed-loop signals almost surely bounded. At last, a simulation is given to verify the effectiveness of the control law.展开更多
Magnetorheological (MR) dampers are one of the most promising new devices for civil infrastructural vibration control applications. However, due to their highly nonlinear dynamic behavior, it is very difficult to obta...Magnetorheological (MR) dampers are one of the most promising new devices for civil infrastructural vibration control applications. However, due to their highly nonlinear dynamic behavior, it is very difficult to obtain of a mathematical model of inverse MR damper that has an explicit relationship between the desired damper force and the command signal (voltage). This force voltage relationship is especially required for the structural vibration control design and simulation using MR dampers. This paper focuses on using a neural network (NN) technique to emulate the inverse MR damper model. The output of the neural network can be used to command the MR damper for generating desired forces. Numerical simulations are also presented to illustrate the effectiveness of this inverse model in semi active vibration control using MR dampers.展开更多
Inertia match of the parallel manipulator means the ratio of the inertial load of the parallel manipulator converted to each actuator shaft and the moment of inertia of the actuator is kept within a reasonable range. ...Inertia match of the parallel manipulator means the ratio of the inertial load of the parallel manipulator converted to each actuator shaft and the moment of inertia of the actuator is kept within a reasonable range. Currently there are many studies on parallel manipulators, but few mention inertia parameters and inertia match of parallel manipulators. This paper focuses on the inertia characteristics of the 3-RRR reconfigurable planar parallel manipulator. On the basis of the inverse dynamic formulations deduced with the principle of virtual work, the inertia matrix of the 3-RRR planar parallel manipulator in the actuator space is obtained in algebraic form. Then, by unifying the dimension and averaging diagonal elements of the inertia matrix, the equivalent inertia of the parallel manipulator, which is the inertial load of the parallel manipulator converted to each actuator shaft, is determined. By transforming the inertia problem of the 3-RRR parallel manipulator into that of the serial multi-bar manipulator, the practicality of the equivalent inertia deduced by inverse dynamics is demonstrated. According to the physical meaning of the inertia equation, the manipulator is divided in to three parts. Further analysis is carried out on the contribution of each part to the equivalent inertia and their distributions in the required workspace, revealing that the passive links cannot ignored in calculating the equivalent inertia of the parallel manipulator. Finally, the inertia match for the 3-RRR reconfigurable parallel manipulator under three configurations is accomplished, and reducers are selected. The equivalent inertia calculation and the inertial match results illustrate that the inertia math is a necessary step to the design of the parallel manipulator, and inertia parameters dramatically affect dynamic performances of parallel manipulators. Besides, the equivalent inertia and inertial match principles, proposed in the paper, can be widely applied in the dynamic analysis and servomotors selecting for the parallel manipulator.展开更多
An overview on nonlinear reconfigurable flight control approaches that have been demonstrated in flight-test or highfidelity simulation is presented. Various approaches for reconfigurable flight control systems are co...An overview on nonlinear reconfigurable flight control approaches that have been demonstrated in flight-test or highfidelity simulation is presented. Various approaches for reconfigurable flight control systems are considered, including nonlinear dynamic inversion, parameter identification and neural network technologies, backstepping and model predictive control approaches. The recent research work, flight tests, and potential strength and weakness of each approach are discussed objectively in order to give readers and researchers some reference. Finally, possible future directions and open problems in this area are addressed.展开更多
A novel fault-tolerant adaptive control methodology against the actuator faults is proposed. The actuator effectiveness factors （AEFs） are introduced to denote the healthy of actuator, and the unscented Kalman filt...A novel fault-tolerant adaptive control methodology against the actuator faults is proposed. The actuator effectiveness factors （AEFs） are introduced to denote the healthy of actuator, and the unscented Kalman filter （UKF） is employed for online estimation of both the motion states and the AEFs of mobile robot. A square root version of the UKF is introduced to improve efficiency and numerical stability. Using the information from the UKF, the reconfigurable controller is designed automatically based on an enhancement inverse dynamic control （IDC） methodology. The experiment on a 3-DOF omni-directional mobile robot is performed, and the effectiveness of the proposed method is demonstrated.展开更多
To avoid impacts and vibrations during the processes of acceleration and deceleration while possessing flexible working ways for cable-suspended parallel robots(CSPRs),point-to-point trajectory planning demands an und...To avoid impacts and vibrations during the processes of acceleration and deceleration while possessing flexible working ways for cable-suspended parallel robots(CSPRs),point-to-point trajectory planning demands an under-constrained cable-suspended parallel robot(UCPR)with variable angle and height cable mast as described in this paper.The end-effector of the UCPR with three cables can achieve three translational degrees of freedom(DOFs).The inverse kinematic and dynamic modeling of the UCPR considering the angle and height of cable mast are completed.The motion trajectory of the end-effector comprising six segments is given.The connection points of the trajectory segments(except for point P3 in the X direction)are devised to have zero instantaneous velocities,which ensure that the acceleration has continuity and the planned acceleration curve achieves smooth transition.The trajectory is respectively planned using three algebraic methods,including fifth degree polynomial,cycloid trajectory,and double-S velocity curve.The results indicate that the trajectory planned by fifth degree polynomial method is much closer to the given trajectory of the end-effector.Numerical simulation and experiments are accomplished for the given trajectory based on fifth degree polynomial planning.At the points where the velocity suddenly changes,the length and tension variation curves of the planned and unplanned three cables are compared and analyzed.The OptiTrack motion capture system is adopted to track the end-effector of the UCPR during the experiment.The effectiveness and feasibility of fifth degree polynomial planning are validated.展开更多
With the strong battlefield application environment of the next generation fighter,based on the design of distributed vehicle management system,a fault diagnosis and fault-tolerant control(FTC)method for wing surface ...With the strong battlefield application environment of the next generation fighter,based on the design of distributed vehicle management system,a fault diagnosis and fault-tolerant control(FTC)method for wing surface damage is proposed in this paper.Aiming at three kinds of wing damage modes,this paper proposes a diagnosis method based on the fault decision tree and forms a fault decision tree for wing damage from the aspects of sample database construction,feature parameter extraction,and fault decision tree construction.Based on the fault diagnosis results,the longitudinal control law based on dynamic inverse and the lateral-directional robust control laws based on linear quadratic regulator(LQR)are proposed.From the simulation examples,the fault diagnosis algorithm based on the decision tree can complete the judgment of three wing surface damage modes within 2 ms,and the FTC law can make the fighter quickly return to a stable flight state after a short transient of 1 s,which achieves the fault-tolerant goal.展开更多
Because of its ease of implementation,a linear PID controller is generally used to control robotic manipulators.Linear controllers cannot effectively cope with uncertainties and variations in the parameters;therefore,...Because of its ease of implementation,a linear PID controller is generally used to control robotic manipulators.Linear controllers cannot effectively cope with uncertainties and variations in the parameters;therefore,nonlinear controllers with robust performance which can cope with these are recommended.The sliding mode control(SMC)is a robust state feedback control method for nonlinear systems that,in addition having a simple design,efficiently overcomes uncertainties and disturbances in the system.It also has a very fast transient response that is desirable when controlling robotic manipulators.The most critical drawback to SMC is chattering in the control input signal.To solve this problem,in this study,SMC is used with a boundary layer(SMCBL)to eliminate the chattering and improve the performance of the system.The proposed SMCBL was compared with inverse dynamic control(IDC),a conventional nonlinear control method.The kinematic and dynamic equations of the IRB-120 robot manipulator were initially extracted completely and accurately,and then the control of the robot manipulator using SMC was evaluated.For validation,the proposed control method was implemented on a 6-DOF IRB-120 robot manipulator in the presence of uncertainties.The results were simulated,tested,and compared in the MATLAB/Simulink environment.To further validate our work,the results were tested and confirmed experimentally on an actual IRB-120 robot manipulator.展开更多
Magnetic-valve controllable reactor(MCR)has characteristics of DC bias and different types of magnetic flux density in the magnetic circuit and winding current distortion.These characteristics not only lead to loss ca...Magnetic-valve controllable reactor(MCR)has characteristics of DC bias and different types of magnetic flux density in the magnetic circuit and winding current distortion.These characteristics not only lead to loss calculation method of MCR different from that of power transformer,but also make it more difficult to calculate the core loss and wingding loss of MCR accurately.Our study combines core partition method with dynamic inverse J-A model to calculate the core loss of MCR.The winding loss coefficient of MCR is proposed,which takes into account the influence of harmonics and magnetic flux leakage on the winding loss of MCR.The result shows that the proposed core loss calculation method and winding loss coefficient are effective and correct for the loss calculation of MCR.展开更多
This paper proposes a method of using multi controllers to control supermaneuverable aircraft. A nonlinear dynamic inversion controller is used for supermaneuver. A gain scheduled controller is used for routine man...This paper proposes a method of using multi controllers to control supermaneuverable aircraft. A nonlinear dynamic inversion controller is used for supermaneuver. A gain scheduled controller is used for routine maneuver. A switch algorithm is designed to switch the controllers. The flight envelopes of the controllers are different but have a common area in which the controllers are switched from one to the other. In the common area, some special boundaries are selected to decide switch conditions. The controllers all use vector thrust for lower velocity maneuver control. Unlike the variation structure theory to use a single boundary, this paper uses two boundaries for switching between the two controllers. One boundary is used for switching from dynamic inversion to gain scheduling, while the other is used for switching from gain scheduling to dynamic inversion. This can effectively avoid the system vibration caused by switching repeatedly at a single boundary. The method is very easy for engineering. It can reduce the risk of design of the supermaneuverable aircraft.展开更多
This paper introduces an electrical drives control architecture combining a fractional-order controller and a setpoint pre-filter. The former is based on a fractional-order proportional-integral(PI) unit, with a non-i...This paper introduces an electrical drives control architecture combining a fractional-order controller and a setpoint pre-filter. The former is based on a fractional-order proportional-integral(PI) unit, with a non-integer order integral action, while the latter can be of integer or non-integer type. To satisfy robustness and dynamic performance specifications, the feedback controller is designed by a loop-shaping technique in the frequency domain. In particular, optimality of the feedback system is pursued to achieve input-output tracking. The setpoint pre-filter is designed by a dynamic inversion technique minimizing the difference between the ideal synthesized command signal(i.e., a smooth monotonic response) and the prefilter step response. Experimental tests validate the methodology and compare the performance of the proposed architecture with well-established control schemes that employ the classical PIbased symmetrical optimum method with a smoothing pre-filter.展开更多
Since the aerodynamic center moving backward sharply in hypersonic flight,the stability margin of the hypersonic vehicle increases largely while the maneuverability decreases.We proposed a novel method to solve this c...Since the aerodynamic center moving backward sharply in hypersonic flight,the stability margin of the hypersonic vehicle increases largely while the maneuverability decreases.We proposed a novel method to solve this contradiction.We used relaxed static stability(RSS)to improve the maneuverability in hypersonic flight,and designed the stability augmentation system(SAS)to ensure the stability in subsonic flight.Therefore,the relationship between static stability and maneuverability was quantitatively analyzed in the first step,and the numerical value of RSS was obtained on the premise of good maneuverability.Secondly,the relationship between static stability and aerodynamic parameters was quantitatively analyzed.We properly adjusted aerodynamic parameters based on the quantitative relationship to achieve the specific static stability set in the first step,and therefore provided the engineering realization methods.The vehicle will be statically unstable in subsonic flight with the specific static stability.Lastly,SAS was needed to ensure the stability of the vehicle in subsonic flight.Simulation studies were conducted by comparing the linear SAS to the nonlinear SAS,and the results showed that the nonlinear dynamicinversion controller can synthesize with proportional-integrall-derivative(PID)controller robustly and stabilize the hypersonic vehicle.展开更多
A discussion is devoted to the design of an adaptive flight control system of the armed helicopter using wavelet neural network method. Firstly, the control loop of the attitude angle is designed with a dynamic invers...A discussion is devoted to the design of an adaptive flight control system of the armed helicopter using wavelet neural network method. Firstly, the control loop of the attitude angle is designed with a dynamic inversion scheme in a quick loop and a slow loop. respectively. Then, in order to compensate the error caused by dynamic inversion, the adaptive flight control system of the armed helicopter using wavelet neural network method is put forward, so the BP wavelet neural network and the Lyapunov stable wavelet neural network are used to design the helicopter flight control system. Finally, the typical maneuver flight is simulated to demonstrate its validity and effectiveness. Result proves that the wavelet neural network has an engineering practical value and the effect of WNN is good.展开更多
The guidance and control for UAV aerial refueling docking based on dynamic inversion with L1 adaptive augmentation is studied.In order to improve the tracking performance of UAV aerial refueling docking,aguidance algo...The guidance and control for UAV aerial refueling docking based on dynamic inversion with L1 adaptive augmentation is studied.In order to improve the tracking performance of UAV aerial refueling docking,aguidance algorithm is developed to satisfy the tracking requirement of position and velocity,and it generates the UAV flight control loop commands.In flight control loop,based on the 6-DOF nonlinear model,the angular rate loop and the attitude loop are separated based on time-scale principle and the control law is designed using dynamic inversion.The throttle control is also derived from dynamic inversion method.Moreover,an L1 adaptive augmentation is developed to compensate for the undesirable effects of modeling uncertainty and disturbance.Nonlinear digital simulations are carried out.The results show that the guidance and control system has good tracking performance and robustness in achieving accurate aerial refueling docking.展开更多
Nonlinear dynamic inversion(NDI)has been applied to the control law design of quad-rotors mainly thanks to its good robustness and simplicity of parameter tuning.However,the weakness of relying on accurate model great...Nonlinear dynamic inversion(NDI)has been applied to the control law design of quad-rotors mainly thanks to its good robustness and simplicity of parameter tuning.However,the weakness of relying on accurate model greatly restrains its application on quad-rotors,especially nano quad-rotors(NQRs).NQRs are easy to be influenced by uncertainties such as model uncertainties(mainly from complicated aerodynamic interferences,strong coupling in roll-pitch-yaw channels and inaccurate aerodynamic prediction of rotors)and external uncertainties(mainly from winds or gusts),particularly persistent ones.Therefore,developing accurate model for altitude and attitude control of NQRs is difficult.To solve this problem,in this paper,an improved nonlinear dynamic inversion(INDI)method is developed,which can reject the above-mentioned uncertainties by estimating them and then counteracting in real time using linear extended state observer(LESO).Comparison with the traditional NDI(TNDI)method was carried out numerically,and the results show that,in coping with persistent uncertainties,the INDI-based method presents significant superiority.展开更多
For the problem of sensor faults and actuator faults in aircraft attitude control,this paper proposes a fault tolerant control(FTC)scheme based on extended state observer(ESO)and nonlinear dynamic inversion(NDI).First...For the problem of sensor faults and actuator faults in aircraft attitude control,this paper proposes a fault tolerant control(FTC)scheme based on extended state observer(ESO)and nonlinear dynamic inversion(NDI).First,two ESOs are designed to estimate sensor faults and actuator faults respectively.Second,the angular rate signal is reconstructed according to the estimation of sensor faults.Third,in angular rate loop,NDI is designed based on reconstruction of angular rate signals and estimation of actuator faults.The FTC scheme proposed in this paper is testified through numerical simulations.The results show that it is feasible and has good fault tolerant ability.展开更多
基金Supported by National Natural Science Foundation of China (No. 50375106) andKey Laboratory of Intelligent Manufacturing at Shantou University Grant (No. Imstu-2002-11).
文摘A systematic methodology for solving the inverse dynamics of the Delta robot is presented.First,the inverse kinematics is solved based on the vector method.A new form of the Jacobi matrix formulized by the vectors is obtained so the three types kinematics singularities namely inverse, direct and combined types, can be identified with the physical meaning.Then based on the principle of virtual work, a methodology for driving the dynamical equations of motion is developed.Meanwhile the whole actuating torques, the torques caused by the gravity, the velocity and the acceleration are computed respectively in the numerical example. Results show that torque caused by the acceleration term is much bigger than the other two terms.This approach leads to efficient algorithms since the constraint forces and moments of the robot system have been eliminated from the equations of motion and there is no differential equation for the whole procedure when the principle of virtual work is applied to solving the inverse dynamical problem.
基金Supported by National Natural Science Foundation of China(Grant No.11672127)Fundamental Research Funds for the Central Universities of China(Grant No.NP2016412)
文摘Overtaking accidents caused by improper operations performed by a driver occur frequently. However, most stud?ies on overtaking safety have neglected research into driver control input. A novel method is proposed to obtain the driver control input during the overtaking process. Meanwhile, to improve the safety of overtaking, two types of safe distances, and the time of the overtaking are considered. Path constraints are established when considering the two types of safe distances. An optimal control model is established to solve the minimum time maneuver under multiple constraints. Using the Gauss pseudospectral method, the optimal control problem is converted into a nonlinear pro?gramming problem, which is then solved through sequential quadratic programming(SQP). In addition, the e ective?ness of the proposed method is verified based on the results of a Carsim simulation. The simulation results show that by adopting an inverse dynamics method to solve the manipulation problem of the vehicle’s minimum overtaking time, the manipulation capability of a vehicle in completing an overtaking safely within the minimum time can be obtained. This method can provide a reference for research into the active safety of manned and unmanned vehicles.
基金Supported by National Natural Science Foundation of China(Grant No.51475211)
文摘Mechanical assembly has its own dynamic quality directly affecting the dynamic quality of whole product and should be considered in quality inspection and estimation of mechanical assembly. Based on functional relations between dynamic characteristics involved in mechanical assembly, the effects of assembling process on dynamic characteristics of substructural components of an assembly system are investigated by substructuring analysis. Assembly-coupling dynamic stiffness is clarified as the dominant factor of the effects and can be used as a quantitative measure of assembly dynamic quality. Two computational schemes using frequency response functions（FRFs） to determine the stiffness are provided and discussed by inverse substructuring analysis, including their applicable conditions and implementation procedure in application. Eigenvalue analysis on matrix-ratios of FRFs before and after assembling is employed and well validates the analytical outcomes and the schemes via both a lumped-parameter model and its analogic experimental counterpart. Applying the two schemes to inspect the dynamic quality provides the message of dynamic performance of the assembly system, and therefore improves conventional quality inspection and estimation of mechanical assembly in completeness.
基金Project(9140A05030109HK01)supported by Equipment Pre-research Foundation,China
文摘It is a complicated nonlinear controlling problem to conduct a two-dimensional trajectory correction of rockets.By establishing the aerodynamic correction force mathematical model of rockets on nose cone swinging,the linear control is realized by the dynamic inverse nonlinear controlling theory and the three-time-scale separation method.The control ability and the simulation results are also tested and verified.The results show that the output responses of system track the expected curve well and the error is controlled in a given margin.The maximum correction is about±314 m in the lengthwise direction and±1 212 m in the crosswise direction from the moment of 5 s to the drop-point time when the angle of fire is 55°.Thus,based on the dynamic inverse control of feedback linearization,the trajectory correction capability of nose cone swinging can satisfy the requirements of two-dimensional ballistic correction,and the validity and effectiveness of the method are proved.
基金supported by National Natural Science Foundation of China (No. 60774010, 10971256, and 60974028)Jiangsu"Six Top Talents" (No. 07-A-020)+2 种基金Natural Science Foundation of Jiangsu Province (No. BK2009083)Program for Fundamental Research of Natural Sciences in Universities of Jiangsu Province(No.07KJB510114)Natural Science Foundation of Xuzhou Normal University (No. 08XLB20)
文摘This paper considers a concrete stochastic nonlinear system with stochastic unmeasurable inverse dynamics. Motivated by the concept of integral input-to-state stability （iISS） in deterministic systems and stochastic input-to-state stability （SISS） in stochastic systems, a concept of stochastic integral input-to-state stability （SiISS） using Lyapunov functions is first introduced. A constructive strategy is proposed to design a dynamic output feedback control law, which drives the state to the origin almost surely while keeping all other closed-loop signals almost surely bounded. At last, a simulation is given to verify the effectiveness of the control law.
文摘Magnetorheological (MR) dampers are one of the most promising new devices for civil infrastructural vibration control applications. However, due to their highly nonlinear dynamic behavior, it is very difficult to obtain of a mathematical model of inverse MR damper that has an explicit relationship between the desired damper force and the command signal (voltage). This force voltage relationship is especially required for the structural vibration control design and simulation using MR dampers. This paper focuses on using a neural network (NN) technique to emulate the inverse MR damper model. The output of the neural network can be used to command the MR damper for generating desired forces. Numerical simulations are also presented to illustrate the effectiveness of this inverse model in semi active vibration control using MR dampers.
基金supported by National Hi-tech Research and Development Program of China (863 Program, Grant No. 2006AA04Z133)National Natural Science Foundation of China (Grant No. 50605035, 10778625)
文摘Inertia match of the parallel manipulator means the ratio of the inertial load of the parallel manipulator converted to each actuator shaft and the moment of inertia of the actuator is kept within a reasonable range. Currently there are many studies on parallel manipulators, but few mention inertia parameters and inertia match of parallel manipulators. This paper focuses on the inertia characteristics of the 3-RRR reconfigurable planar parallel manipulator. On the basis of the inverse dynamic formulations deduced with the principle of virtual work, the inertia matrix of the 3-RRR planar parallel manipulator in the actuator space is obtained in algebraic form. Then, by unifying the dimension and averaging diagonal elements of the inertia matrix, the equivalent inertia of the parallel manipulator, which is the inertial load of the parallel manipulator converted to each actuator shaft, is determined. By transforming the inertia problem of the 3-RRR parallel manipulator into that of the serial multi-bar manipulator, the practicality of the equivalent inertia deduced by inverse dynamics is demonstrated. According to the physical meaning of the inertia equation, the manipulator is divided in to three parts. Further analysis is carried out on the contribution of each part to the equivalent inertia and their distributions in the required workspace, revealing that the passive links cannot ignored in calculating the equivalent inertia of the parallel manipulator. Finally, the inertia match for the 3-RRR reconfigurable parallel manipulator under three configurations is accomplished, and reducers are selected. The equivalent inertia calculation and the inertial match results illustrate that the inertia math is a necessary step to the design of the parallel manipulator, and inertia parameters dramatically affect dynamic performances of parallel manipulators. Besides, the equivalent inertia and inertial match principles, proposed in the paper, can be widely applied in the dynamic analysis and servomotors selecting for the parallel manipulator.
基金supported by the National Natural Science Foundation of China (61273171)the National Aerospace Science Foundation of China (2011ZA52009)
文摘An overview on nonlinear reconfigurable flight control approaches that have been demonstrated in flight-test or highfidelity simulation is presented. Various approaches for reconfigurable flight control systems are considered, including nonlinear dynamic inversion, parameter identification and neural network technologies, backstepping and model predictive control approaches. The recent research work, flight tests, and potential strength and weakness of each approach are discussed objectively in order to give readers and researchers some reference. Finally, possible future directions and open problems in this area are addressed.
基金This project is supported by National Hi-tech Research and Development Program of China (863 Program, No. 2003AA421020).
文摘A novel fault-tolerant adaptive control methodology against the actuator faults is proposed. The actuator effectiveness factors （AEFs） are introduced to denote the healthy of actuator, and the unscented Kalman filter （UKF） is employed for online estimation of both the motion states and the AEFs of mobile robot. A square root version of the UKF is introduced to improve efficiency and numerical stability. Using the information from the UKF, the reconfigurable controller is designed automatically based on an enhancement inverse dynamic control （IDC） methodology. The experiment on a 3-DOF omni-directional mobile robot is performed, and the effectiveness of the proposed method is demonstrated.
基金National Natural Science Foundation of China(Grant Nos.51925502,51575150).
文摘To avoid impacts and vibrations during the processes of acceleration and deceleration while possessing flexible working ways for cable-suspended parallel robots(CSPRs),point-to-point trajectory planning demands an under-constrained cable-suspended parallel robot(UCPR)with variable angle and height cable mast as described in this paper.The end-effector of the UCPR with three cables can achieve three translational degrees of freedom(DOFs).The inverse kinematic and dynamic modeling of the UCPR considering the angle and height of cable mast are completed.The motion trajectory of the end-effector comprising six segments is given.The connection points of the trajectory segments(except for point P3 in the X direction)are devised to have zero instantaneous velocities,which ensure that the acceleration has continuity and the planned acceleration curve achieves smooth transition.The trajectory is respectively planned using three algebraic methods,including fifth degree polynomial,cycloid trajectory,and double-S velocity curve.The results indicate that the trajectory planned by fifth degree polynomial method is much closer to the given trajectory of the end-effector.Numerical simulation and experiments are accomplished for the given trajectory based on fifth degree polynomial planning.At the points where the velocity suddenly changes,the length and tension variation curves of the planned and unplanned three cables are compared and analyzed.The OptiTrack motion capture system is adopted to track the end-effector of the UCPR during the experiment.The effectiveness and feasibility of fifth degree polynomial planning are validated.
基金This work was supported by the Defense Industrial Technology Development Program(JCKY2016205C013).
文摘With the strong battlefield application environment of the next generation fighter,based on the design of distributed vehicle management system,a fault diagnosis and fault-tolerant control(FTC)method for wing surface damage is proposed in this paper.Aiming at three kinds of wing damage modes,this paper proposes a diagnosis method based on the fault decision tree and forms a fault decision tree for wing damage from the aspects of sample database construction,feature parameter extraction,and fault decision tree construction.Based on the fault diagnosis results,the longitudinal control law based on dynamic inverse and the lateral-directional robust control laws based on linear quadratic regulator(LQR)are proposed.From the simulation examples,the fault diagnosis algorithm based on the decision tree can complete the judgment of three wing surface damage modes within 2 ms,and the FTC law can make the fighter quickly return to a stable flight state after a short transient of 1 s,which achieves the fault-tolerant goal.
文摘Because of its ease of implementation,a linear PID controller is generally used to control robotic manipulators.Linear controllers cannot effectively cope with uncertainties and variations in the parameters;therefore,nonlinear controllers with robust performance which can cope with these are recommended.The sliding mode control(SMC)is a robust state feedback control method for nonlinear systems that,in addition having a simple design,efficiently overcomes uncertainties and disturbances in the system.It also has a very fast transient response that is desirable when controlling robotic manipulators.The most critical drawback to SMC is chattering in the control input signal.To solve this problem,in this study,SMC is used with a boundary layer(SMCBL)to eliminate the chattering and improve the performance of the system.The proposed SMCBL was compared with inverse dynamic control(IDC),a conventional nonlinear control method.The kinematic and dynamic equations of the IRB-120 robot manipulator were initially extracted completely and accurately,and then the control of the robot manipulator using SMC was evaluated.For validation,the proposed control method was implemented on a 6-DOF IRB-120 robot manipulator in the presence of uncertainties.The results were simulated,tested,and compared in the MATLAB/Simulink environment.To further validate our work,the results were tested and confirmed experimentally on an actual IRB-120 robot manipulator.
基金National Natural Science Foundation of China(No.51367010)Science and Technology Program of Gansu Province(No.17JR5RA083)Program for Excellent Team of Scientific Research in Lanzhou Jiaotong University(No.201701)。
文摘Magnetic-valve controllable reactor(MCR)has characteristics of DC bias and different types of magnetic flux density in the magnetic circuit and winding current distortion.These characteristics not only lead to loss calculation method of MCR different from that of power transformer,but also make it more difficult to calculate the core loss and wingding loss of MCR accurately.Our study combines core partition method with dynamic inverse J-A model to calculate the core loss of MCR.The winding loss coefficient of MCR is proposed,which takes into account the influence of harmonics and magnetic flux leakage on the winding loss of MCR.The result shows that the proposed core loss calculation method and winding loss coefficient are effective and correct for the loss calculation of MCR.
文摘This paper proposes a method of using multi controllers to control supermaneuverable aircraft. A nonlinear dynamic inversion controller is used for supermaneuver. A gain scheduled controller is used for routine maneuver. A switch algorithm is designed to switch the controllers. The flight envelopes of the controllers are different but have a common area in which the controllers are switched from one to the other. In the common area, some special boundaries are selected to decide switch conditions. The controllers all use vector thrust for lower velocity maneuver control. Unlike the variation structure theory to use a single boundary, this paper uses two boundaries for switching between the two controllers. One boundary is used for switching from dynamic inversion to gain scheduling, while the other is used for switching from gain scheduling to dynamic inversion. This can effectively avoid the system vibration caused by switching repeatedly at a single boundary. The method is very easy for engineering. It can reduce the risk of design of the supermaneuverable aircraft.
基金partially supported by the Australian Research Council(DP160104994)
文摘This paper introduces an electrical drives control architecture combining a fractional-order controller and a setpoint pre-filter. The former is based on a fractional-order proportional-integral(PI) unit, with a non-integer order integral action, while the latter can be of integer or non-integer type. To satisfy robustness and dynamic performance specifications, the feedback controller is designed by a loop-shaping technique in the frequency domain. In particular, optimality of the feedback system is pursued to achieve input-output tracking. The setpoint pre-filter is designed by a dynamic inversion technique minimizing the difference between the ideal synthesized command signal(i.e., a smooth monotonic response) and the prefilter step response. Experimental tests validate the methodology and compare the performance of the proposed architecture with well-established control schemes that employ the classical PIbased symmetrical optimum method with a smoothing pre-filter.
基金supported in part by the National Natural Science Foundation of China(Nos.61673209,61741313)the Funding of Jiangsu Innovation Program for Graduate Education(No.CXZZ13_0170)+3 种基金the Funding for Outstanding Doctoral Dissertation in NUAA(No.BCXJ13-06)the Jiangsu Six Peak of Talents Program(No.KTHY-027)the Funding of China Launch Vehicle Technology Innovation Program of University and Institute(No.CALT201503)the Aeronautical Science Foundation(No.2016ZA52009)
文摘Since the aerodynamic center moving backward sharply in hypersonic flight,the stability margin of the hypersonic vehicle increases largely while the maneuverability decreases.We proposed a novel method to solve this contradiction.We used relaxed static stability(RSS)to improve the maneuverability in hypersonic flight,and designed the stability augmentation system(SAS)to ensure the stability in subsonic flight.Therefore,the relationship between static stability and maneuverability was quantitatively analyzed in the first step,and the numerical value of RSS was obtained on the premise of good maneuverability.Secondly,the relationship between static stability and aerodynamic parameters was quantitatively analyzed.We properly adjusted aerodynamic parameters based on the quantitative relationship to achieve the specific static stability set in the first step,and therefore provided the engineering realization methods.The vehicle will be statically unstable in subsonic flight with the specific static stability.Lastly,SAS was needed to ensure the stability of the vehicle in subsonic flight.Simulation studies were conducted by comparing the linear SAS to the nonlinear SAS,and the results showed that the nonlinear dynamicinversion controller can synthesize with proportional-integrall-derivative(PID)controller robustly and stabilize the hypersonic vehicle.
文摘A discussion is devoted to the design of an adaptive flight control system of the armed helicopter using wavelet neural network method. Firstly, the control loop of the attitude angle is designed with a dynamic inversion scheme in a quick loop and a slow loop. respectively. Then, in order to compensate the error caused by dynamic inversion, the adaptive flight control system of the armed helicopter using wavelet neural network method is put forward, so the BP wavelet neural network and the Lyapunov stable wavelet neural network are used to design the helicopter flight control system. Finally, the typical maneuver flight is simulated to demonstrate its validity and effectiveness. Result proves that the wavelet neural network has an engineering practical value and the effect of WNN is good.
基金supported by the National Natural Science Foundation of China(No.61273050)the Aeronautical Science Foundation of China(No.20121352026)
文摘The guidance and control for UAV aerial refueling docking based on dynamic inversion with L1 adaptive augmentation is studied.In order to improve the tracking performance of UAV aerial refueling docking,aguidance algorithm is developed to satisfy the tracking requirement of position and velocity,and it generates the UAV flight control loop commands.In flight control loop,based on the 6-DOF nonlinear model,the angular rate loop and the attitude loop are separated based on time-scale principle and the control law is designed using dynamic inversion.The throttle control is also derived from dynamic inversion method.Moreover,an L1 adaptive augmentation is developed to compensate for the undesirable effects of modeling uncertainty and disturbance.Nonlinear digital simulations are carried out.The results show that the guidance and control system has good tracking performance and robustness in achieving accurate aerial refueling docking.
基金supported by the Priority Academic Program Development of Jiangsu Higher Education Institutions(PAPD)the Advanced Research Project of Army Equipment Development(No.301020803)
文摘Nonlinear dynamic inversion(NDI)has been applied to the control law design of quad-rotors mainly thanks to its good robustness and simplicity of parameter tuning.However,the weakness of relying on accurate model greatly restrains its application on quad-rotors,especially nano quad-rotors(NQRs).NQRs are easy to be influenced by uncertainties such as model uncertainties(mainly from complicated aerodynamic interferences,strong coupling in roll-pitch-yaw channels and inaccurate aerodynamic prediction of rotors)and external uncertainties(mainly from winds or gusts),particularly persistent ones.Therefore,developing accurate model for altitude and attitude control of NQRs is difficult.To solve this problem,in this paper,an improved nonlinear dynamic inversion(INDI)method is developed,which can reject the above-mentioned uncertainties by estimating them and then counteracting in real time using linear extended state observer(LESO).Comparison with the traditional NDI(TNDI)method was carried out numerically,and the results show that,in coping with persistent uncertainties,the INDI-based method presents significant superiority.
基金supported by the Chinese Aviation Science Fund(20160757001)the National Natural Science Foundation of China(10577012)。
文摘For the problem of sensor faults and actuator faults in aircraft attitude control,this paper proposes a fault tolerant control(FTC)scheme based on extended state observer(ESO)and nonlinear dynamic inversion(NDI).First,two ESOs are designed to estimate sensor faults and actuator faults respectively.Second,the angular rate signal is reconstructed according to the estimation of sensor faults.Third,in angular rate loop,NDI is designed based on reconstruction of angular rate signals and estimation of actuator faults.The FTC scheme proposed in this paper is testified through numerical simulations.The results show that it is feasible and has good fault tolerant ability.
