The difficulties associated with performing direct compression strength tests on rocks lead to the development of indirect test methods for the rock strength assessment. Indirect test methods are simple, more economic...The difficulties associated with performing direct compression strength tests on rocks lead to the development of indirect test methods for the rock strength assessment. Indirect test methods are simple, more economical, less time-consuming, and easily adaptable to the field. The main aim of this study was to derive correlations between direct and indirect test methods for basalt and rhyolite rock types from Carlin trend deposits in Nevada. In the destructive methods, point load index, block punch index, and splitting tensile strength tests are performed. In the non-destructive methods, Schmidt hammer and ultrasonic pulse velocity tests are performed. Correlations between the direct and indirect compression strength tests are developed using linear and nonlinear regression analysis methods. The results show that the splitting tensile strength has the best correlation with the uniaxial compression strength.Furthermore, the Poisson's ratio has no correlation with any of the direct and indirect test results.展开更多
In marine engineering, the strength of a submarine sediment is an indispensable parameter for assessment of construction. In this study, a free-fall cone penetrator named IPen was developed to realize a rapid and effi...In marine engineering, the strength of a submarine sediment is an indispensable parameter for assessment of construction. In this study, a free-fall cone penetrator named IPen was developed to realize a rapid and efficient measurement of sediment strength. The equipment is characterized by modular design and self-contained data acquisition. It is equipped with an acceleration sensor, a water pressure sensor, and a piezocone penetration test(CPTu) probe. It is designed to be released from near seabed surface with a releaser and then fall freely to provide a higher penetration velocity. Its maximum working depth is approximately 2500 m and maximum penetration depth is approximately 3 m. To derive the correlation between penetration resistance and sediment strength, a calibrator was devised to determine the penetration-rate factor. In addition, the factor applicable to in situ test points was determined in laboratory experiments. In June 2016, the IPen was tested in situ in the South Yellow Sea, China, during a shared voyage funded by the National Science Foundation. Meanwhile, undisturbed column samples were collected for laboratory tests. Based on the in situ test results, it was demonstrated that the IPen could accurately record the working states of various sensors during the freely falling course. IPen test results reliably reflected the sediment strength at all the testing points when compared with laboratory calibration tests, in situ vane tests and penetration tests, laboratory penetration tests, and unconsolidated and undrained triaxial compression tests.展开更多
Hip adduction strength tests are commonly used in clinical practice to provide an accurate diagnosis of groin injuries. Athletes with reduced adductor muscle strength are at risk of developing groin injuries. Our stud...Hip adduction strength tests are commonly used in clinical practice to provide an accurate diagnosis of groin injuries. Athletes with reduced adductor muscle strength are at risk of developing groin injuries. Our study aimed to evaluate the relative and absolute test-retest reliability of the side-lying eccentric hip adduction strength test and the long-lever adduction squeeze test using the K-Force hand-held dynamometer. Twenty physically active male individuals with a mean age (±SD) of 30.7 (±7.3) years were included. Both tests presented excellent test-retest reliability (Intraclass Correlation Coefficient: 0.77 - 0.95). The best and mean scores of the eccentric and isometric tests presented the smallest test-retest variation (MDC%: 12.8 - 14.9 and MDC%: 14.6 - 18.7, respectively). Our study showed that the K-Force dynamometer has excellent reliability for assessing hip adduction strength in two different testing positions. We suggest the best and mean of three repetitions for clinical practice as they present the lowest variability. Further research evaluating its clinimetric properties in different populations and gender is recommended.展开更多
A discrete element method （DEM） called particle flow code （PFC2D） was used to construct a model for Brazilian disc splitting test in the present study. Based on the experimental results of intact Brazilian disc of...A discrete element method （DEM） called particle flow code （PFC2D） was used to construct a model for Brazilian disc splitting test in the present study. Based on the experimental results of intact Brazilian disc of rock-like material, a set of micro-parameters in PFC2D that reflected the macro-mechanical behavior of rock-like materials were obtained. And then PFC2D was used to simulate Brazilian splitting test for jointed rock mass specimens and specimen containing a central straight notch. The effect of joint angle and notch angle on the tensile strength and failure mode of jointed rock specimens was detailed analyzed. In order to reveal the meso-mechanical mechanism of crack coalescence, displacement trend lines were applied to analyze the displacement evolution during the crack initiation and propagation. The investigated conclusions can be described as follows. （1） The tensile strength of jointed rock mass disc specimen is dependent to the joint angle. As the joint angle increases, the tensile strength of jointed rock specimen takes on a nonlinear variance. （2） The tensile strength of jointed rock mass disc specimen containing a central straight notch distributes as a function of both joint angle and notch angle. （3） Three major failure modes, i.e., pure tensile failure, shear failure and mixed tension and shear failure mode are observed in jointed rock mass disc specimens under Brazilian test. （4） The notch angle roles on crack initiation and and joint angle play important propagation characteristics of jointed rock mass disc specimen containing a central straight notch under Brazilian test.展开更多
Recently, the effects of high temperature on compressive strength and elastic modulus of high strength concrete were experimentally investigated. The present study is aimed to study the effect of elevated temperatures...Recently, the effects of high temperature on compressive strength and elastic modulus of high strength concrete were experimentally investigated. The present study is aimed to study the effect of elevated temperatures ranging from 20 ℃ to 700 ℃ on the material mechanical properties of high-strength concrete of 40, 60 and 80 MPa grade. During the strength test, the specimens are subjected to a 25% of ultimate compressive strength at room temperature and sustained during heating, and when the target temperature is reached, the specimens are loaded to failure. The tests were conducted at various temperatures (20-700 ℃) for concretes made with W/B ratios of 46%, 32% and 25%, respectively. The results show that the relative values of compressive strength and elastic modulus decrease with increasing compressive strength grade of specimen.展开更多
The strength curves of lightweight aggregate concrete （LWAC） were tested based on detecting LWAC with density of 1 400-1 900 kg/m3 and LWAC with strength grade of LC15-LC50 by rebound method and ultrasonic-rebound c...The strength curves of lightweight aggregate concrete （LWAC） were tested based on detecting LWAC with density of 1 400-1 900 kg/m3 and LWAC with strength grade of LC15-LC50 by rebound method and ultrasonic-rebound combined method.The results show that the common measured strength curves tested by above two methods can not satisfy the required accuracy of LWAC strength test.In addition,specified compressive strength curves of testing LWAC by rebound method and ultrasonic-rebound combined method are obtained,respectively.展开更多
An in-plane load measuring technique is developed to perform the strength test of the micro-cantilever. Based on electromagnetism theorem, Micro UTM (Universal Testing Machine) was in-house made with the load range &#...An in-plane load measuring technique is developed to perform the strength test of the micro-cantilever. Based on electromagnetism theorem, Micro UTM (Universal Testing Machine) was in-house made with the load range ±1 N and the displacement range ±300 μm. It applies an in-plane load on the free-end of the micro-cantilever. The load acts as a bending moment for the root of the cantilever, but as a torque for the anchor. The results show that for samples with different sizes the ultimate loads range from 1.3 to 69.8 mN and the calculated torque is ap-proximately proportional to the square of the bonding length. Two failure modes, fracture at the root of the cantilever and fracture at the anchor, are observed by micro examination to the debris, which indicates that there is a critical design to achieve the strength bal-ance between the cantilever and the anchor. The work demonstrates that Micro UTM is a powerful in-strument for the strength test of the micro-cantilever and similar micro-structures.展开更多
Basic magnesium sulfate cement coral aggregate concrete(MCAC)is a new type of concrete consisting of basic magnesium sulfate cement,coarse coral aggregate,coral reef sand and seawater.The rebound hammer(RH),the ultras...Basic magnesium sulfate cement coral aggregate concrete(MCAC)is a new type of concrete consisting of basic magnesium sulfate cement,coarse coral aggregate,coral reef sand and seawater.The rebound hammer(RH),the ultrasonic pulse velocity(UPV)and the compressive strength(fcu)tests of 14 sets of cube specimens of the MCAC after 28 d of aging were conducted.The impact of the content and length of sisal fiber on the relationship between the fcu-RH and the fcu-UPV was determined.A mathematical model was established to predict the strength of the MCAC using the UPV,RH,and comprehensive UPV/RH methods and to obtain the curves of test strength.The applicability of the test strength curves of ordinary portland concrete(OPC),light-weight aggregate concrete(LAC),and coral aggregate concrete(CAC)to MCAC was assessed.The results showed that the test strength curves of OPC,LAC and CAC were inappropriate to determine the strength of MCAC using non-destructive method.The relative standard error of the curves of test strength of the RH method and the comprehensive method met the specifications,whereas that of the UPV method did not.展开更多
The current practice of geotechnical engineering commonly uses a combination of theoretical and empirical correlations to estimate the soil undrained shear strength in clays from the piezocone test. In order to comple...The current practice of geotechnical engineering commonly uses a combination of theoretical and empirical correlations to estimate the soil undrained shear strength in clays from the piezocone test. In order to complement the use of such correlations, the application of a method to estimate the soil undrained shear strength, using measures of the excess pore pressure in dissipation tests of piezocone is presented. In cohesive soils, excess pore pressure and undrained shear strength are dependent on the same variables (stress state, stress history, soil stiffness), which allows them to be related by the theoretical cavity expansion-critical state framework. This paper mentions the mathematical formulation that supports the theoretical framework used, its relationship with the Nkt and NΔu factors and their estimation in a case studied. The results obtained are consistent within the dispersion found in the international literature and encourage the use of the method in engineering practice.展开更多
Background: Test-retest strength reliability of the Electronic Push/Pull Dynamometer (EPPD) in the measurement of the extensor and flexor muscles on a new constructed chair. The objective of the study was to assess re...Background: Test-retest strength reliability of the Electronic Push/Pull Dynamometer (EPPD) in the measurement of the extensor and flexor muscles on a new constructed chair. The objective of the study was to assess reliability of Electronic Push/Pull Dynamometer in the measurement of the knee flexion and extension at 90° and 60° on a new constructed chair. The aims of the author: To assess reliability of Electronic Push/Pull Dynamometer in the measurement of the knee flexion and extension at 90° and 60° on a new constructed chair. Design: A test-retest reliability study. Subjects: One hundred healthy students male and female (mean age, 21y). Methods: Maximum isometric strength of the quadriceps and hamstring muscle groups was measured using the EPPD were recorded at 60° and 90° for 3 trials on 2 occasions. Reliability was assessed with the Intraclass correlation coefficient (ICC), mean and standard deviation (SD) of measurements, and smallest real differences were calculated for the maximum and for the mean and work of the 3 repetitions. Results: Mean strength ranged from 50.44 kg for knee flexion to 55.76 kg for knee extension 50.44 kg to 61.98 kg at 90° hip flexion. Test-retest reliability Intraclass correlation coefficients (ICCs) ranged from 0.85 to 0.99. ICCs for test-retest reliability ranged from 0.780 to 0.998. Conclusions: The results of the reliability study indicate that the EPPD in reliable dynamometer to use in determining lower limb muscle force production. It can be used to measure disease progression and to evaluate changes in knee extension and flexion strength at the individual patient level.展开更多
This paper describes an investigation of a high-strength concrete frame reinforced with high-strength rebars that was tested in the structure engineering laboratory at Shenyang Jianzhu University. The frame specimen w...This paper describes an investigation of a high-strength concrete frame reinforced with high-strength rebars that was tested in the structure engineering laboratory at Shenyang Jianzhu University. The frame specimen was pseudo- dynamically loaded to indicate three earthquake ground motions of different hazard levels, after which the test specimen was subjected to a pseudo-static loading. This paper focuses on the design, construction and experiment of the test frame and validation of the simulation models. Research shows that a high-strength concrete frame reinforced with high-strength rebars is more efficient and economical than a traditional reinforced concrete frame structure. In addition to the economies achieved by effective use of materials, research shows that the frame can provide enough strength to exceed conventional reinforced concrete frames and provide acceptable ductility. The test study provides evidence to validate the performance of a high- strength concrete frame designed according to current seismic code provisions. Based on previous test research, a nonlinear FEM analysis is completcd by using OpenSees software, The dynamic responses of the frame structure are numerically analyzed, The results of the numerical simulation show that the model can calculate the seismic responses of the frame by OpenSees. At the same time, the test provides additional opportunities to validate the performance of the simulation models.展开更多
Treatment of peat soil foundation in Yunnan surrounding Dianchi and Erhai Lakes poses complex problems for engineering projects.It is insufficient to rely on ordinary cement to reinforce peat soil.In order to make the...Treatment of peat soil foundation in Yunnan surrounding Dianchi and Erhai Lakes poses complex problems for engineering projects.It is insufficient to rely on ordinary cement to reinforce peat soil.In order to make the reinforcement reliable,this experiment mixed(ultrafine cement)UFC into ordinary cement to form a composite solidify agent.This study aimed to analyze the influence of UFC proportion on the strength of cement-soil in the peat soil environment.Unconfined compressive strength(UCS)and scanning electron microscope(SEM)tests were conducted on samples soaked for 28 and 90 days,respectively.The test results show that without considering the effects of Humic Acid(HA)and Fulvic Acid(FA),incorporating UFC can significantly improve the UCS of cement-soil.The rapid hydration of the fine particles generates a large number of cementitious products,improves the cohesion of the soil skeleton,and fills the pores.However,when the proportion of UFC increases,the aggregate structure formed by a larger quantity of fine particles reduces the hydration rate and degree of cement hydration,making the UCS growth rate of cement-soil insignificant.In the peat soil environment,HA significantly weakened the UCS of cement-soil in both physical and chemical aspects.However,UFC can mitigate the adverse effect of HA on cement-soil by its small particle size,high surface energy,and solid binding ability.In addition,FA has a positive effect on the UCS of cement-soil soaked for 28 days and 90 days.The UFC addition could promote the enhancement effect of FA on cement-soil UCS.SEM test results showed that cement hydration products increased significantly with the increase of UFC proportion,and cementation between hydration products and soil particles was enhanced.The size and connectivity of cement-soil pores were significantly reduced,thereby improving cement-soil structural integrity.展开更多
基金CDC/NIOSH for their partial funding of this work
文摘The difficulties associated with performing direct compression strength tests on rocks lead to the development of indirect test methods for the rock strength assessment. Indirect test methods are simple, more economical, less time-consuming, and easily adaptable to the field. The main aim of this study was to derive correlations between direct and indirect test methods for basalt and rhyolite rock types from Carlin trend deposits in Nevada. In the destructive methods, point load index, block punch index, and splitting tensile strength tests are performed. In the non-destructive methods, Schmidt hammer and ultrasonic pulse velocity tests are performed. Correlations between the direct and indirect compression strength tests are developed using linear and nonlinear regression analysis methods. The results show that the splitting tensile strength has the best correlation with the uniaxial compression strength.Furthermore, the Poisson's ratio has no correlation with any of the direct and indirect test results.
基金funded by the National Natural Science Foundation of China (Nos. 41502265 and 41427803)the Key Research and Development Program of Shandong Province, China (No. 2016ZDJS09A03)+1 种基金Data acquisition and sample collections were supported by NSFC Open Research Cruise (Cruise Nos. NORC2016-01 and NORC2017-05)funded by Shiptime Sharing Project of NSFC
文摘In marine engineering, the strength of a submarine sediment is an indispensable parameter for assessment of construction. In this study, a free-fall cone penetrator named IPen was developed to realize a rapid and efficient measurement of sediment strength. The equipment is characterized by modular design and self-contained data acquisition. It is equipped with an acceleration sensor, a water pressure sensor, and a piezocone penetration test(CPTu) probe. It is designed to be released from near seabed surface with a releaser and then fall freely to provide a higher penetration velocity. Its maximum working depth is approximately 2500 m and maximum penetration depth is approximately 3 m. To derive the correlation between penetration resistance and sediment strength, a calibrator was devised to determine the penetration-rate factor. In addition, the factor applicable to in situ test points was determined in laboratory experiments. In June 2016, the IPen was tested in situ in the South Yellow Sea, China, during a shared voyage funded by the National Science Foundation. Meanwhile, undisturbed column samples were collected for laboratory tests. Based on the in situ test results, it was demonstrated that the IPen could accurately record the working states of various sensors during the freely falling course. IPen test results reliably reflected the sediment strength at all the testing points when compared with laboratory calibration tests, in situ vane tests and penetration tests, laboratory penetration tests, and unconsolidated and undrained triaxial compression tests.
文摘Hip adduction strength tests are commonly used in clinical practice to provide an accurate diagnosis of groin injuries. Athletes with reduced adductor muscle strength are at risk of developing groin injuries. Our study aimed to evaluate the relative and absolute test-retest reliability of the side-lying eccentric hip adduction strength test and the long-lever adduction squeeze test using the K-Force hand-held dynamometer. Twenty physically active male individuals with a mean age (±SD) of 30.7 (±7.3) years were included. Both tests presented excellent test-retest reliability (Intraclass Correlation Coefficient: 0.77 - 0.95). The best and mean scores of the eccentric and isometric tests presented the smallest test-retest variation (MDC%: 12.8 - 14.9 and MDC%: 14.6 - 18.7, respectively). Our study showed that the K-Force dynamometer has excellent reliability for assessing hip adduction strength in two different testing positions. We suggest the best and mean of three repetitions for clinical practice as they present the lowest variability. Further research evaluating its clinimetric properties in different populations and gender is recommended.
基金supported by the National Basic Research Programof China(2014CB046905)the Fundamental Research Funds for the Central Universities(China University of Mining and Technology)(2014YC10)
文摘A discrete element method （DEM） called particle flow code （PFC2D） was used to construct a model for Brazilian disc splitting test in the present study. Based on the experimental results of intact Brazilian disc of rock-like material, a set of micro-parameters in PFC2D that reflected the macro-mechanical behavior of rock-like materials were obtained. And then PFC2D was used to simulate Brazilian splitting test for jointed rock mass specimens and specimen containing a central straight notch. The effect of joint angle and notch angle on the tensile strength and failure mode of jointed rock specimens was detailed analyzed. In order to reveal the meso-mechanical mechanism of crack coalescence, displacement trend lines were applied to analyze the displacement evolution during the crack initiation and propagation. The investigated conclusions can be described as follows. （1） The tensile strength of jointed rock mass disc specimen is dependent to the joint angle. As the joint angle increases, the tensile strength of jointed rock specimen takes on a nonlinear variance. （2） The tensile strength of jointed rock mass disc specimen containing a central straight notch distributes as a function of both joint angle and notch angle. （3） Three major failure modes, i.e., pure tensile failure, shear failure and mixed tension and shear failure mode are observed in jointed rock mass disc specimens under Brazilian test. （4） The notch angle roles on crack initiation and and joint angle play important propagation characteristics of jointed rock mass disc specimen containing a central straight notch under Brazilian test.
基金The Korea Research Foundation Grant and Brain Korea 21-2th (BK21-2th) funded by the Korean government (MOEHRD,Basic Research Promotion Fund) (KRF-2007-314-D00271)
文摘Recently, the effects of high temperature on compressive strength and elastic modulus of high strength concrete were experimentally investigated. The present study is aimed to study the effect of elevated temperatures ranging from 20 ℃ to 700 ℃ on the material mechanical properties of high-strength concrete of 40, 60 and 80 MPa grade. During the strength test, the specimens are subjected to a 25% of ultimate compressive strength at room temperature and sustained during heating, and when the target temperature is reached, the specimens are loaded to failure. The tests were conducted at various temperatures (20-700 ℃) for concretes made with W/B ratios of 46%, 32% and 25%, respectively. The results show that the relative values of compressive strength and elastic modulus decrease with increasing compressive strength grade of specimen.
文摘The strength curves of lightweight aggregate concrete （LWAC） were tested based on detecting LWAC with density of 1 400-1 900 kg/m3 and LWAC with strength grade of LC15-LC50 by rebound method and ultrasonic-rebound combined method.The results show that the common measured strength curves tested by above two methods can not satisfy the required accuracy of LWAC strength test.In addition,specified compressive strength curves of testing LWAC by rebound method and ultrasonic-rebound combined method are obtained,respectively.
基金The authors would like to thank Mr.Zhang Dacheng and Ruan Yong from Peking University for their assistance in sample preparation.This work was supported by the National Natural Science Foundation of China(Grant Nos.10432050,10572142).
文摘An in-plane load measuring technique is developed to perform the strength test of the micro-cantilever. Based on electromagnetism theorem, Micro UTM (Universal Testing Machine) was in-house made with the load range ±1 N and the displacement range ±300 μm. It applies an in-plane load on the free-end of the micro-cantilever. The load acts as a bending moment for the root of the cantilever, but as a torque for the anchor. The results show that for samples with different sizes the ultimate loads range from 1.3 to 69.8 mN and the calculated torque is ap-proximately proportional to the square of the bonding length. Two failure modes, fracture at the root of the cantilever and fracture at the anchor, are observed by micro examination to the debris, which indicates that there is a critical design to achieve the strength bal-ance between the cantilever and the anchor. The work demonstrates that Micro UTM is a powerful in-strument for the strength test of the micro-cantilever and similar micro-structures.
基金Funded by National Natural Science Foundation of China(Nos.51878350,11832013,52078250)the Postgraduate Research&Practice Innovation Program of Jiangsu Province(No.KYCX21_0236)。
文摘Basic magnesium sulfate cement coral aggregate concrete(MCAC)is a new type of concrete consisting of basic magnesium sulfate cement,coarse coral aggregate,coral reef sand and seawater.The rebound hammer(RH),the ultrasonic pulse velocity(UPV)and the compressive strength(fcu)tests of 14 sets of cube specimens of the MCAC after 28 d of aging were conducted.The impact of the content and length of sisal fiber on the relationship between the fcu-RH and the fcu-UPV was determined.A mathematical model was established to predict the strength of the MCAC using the UPV,RH,and comprehensive UPV/RH methods and to obtain the curves of test strength.The applicability of the test strength curves of ordinary portland concrete(OPC),light-weight aggregate concrete(LAC),and coral aggregate concrete(CAC)to MCAC was assessed.The results showed that the test strength curves of OPC,LAC and CAC were inappropriate to determine the strength of MCAC using non-destructive method.The relative standard error of the curves of test strength of the RH method and the comprehensive method met the specifications,whereas that of the UPV method did not.
文摘The current practice of geotechnical engineering commonly uses a combination of theoretical and empirical correlations to estimate the soil undrained shear strength in clays from the piezocone test. In order to complement the use of such correlations, the application of a method to estimate the soil undrained shear strength, using measures of the excess pore pressure in dissipation tests of piezocone is presented. In cohesive soils, excess pore pressure and undrained shear strength are dependent on the same variables (stress state, stress history, soil stiffness), which allows them to be related by the theoretical cavity expansion-critical state framework. This paper mentions the mathematical formulation that supports the theoretical framework used, its relationship with the Nkt and NΔu factors and their estimation in a case studied. The results obtained are consistent within the dispersion found in the international literature and encourage the use of the method in engineering practice.
文摘Background: Test-retest strength reliability of the Electronic Push/Pull Dynamometer (EPPD) in the measurement of the extensor and flexor muscles on a new constructed chair. The objective of the study was to assess reliability of Electronic Push/Pull Dynamometer in the measurement of the knee flexion and extension at 90° and 60° on a new constructed chair. The aims of the author: To assess reliability of Electronic Push/Pull Dynamometer in the measurement of the knee flexion and extension at 90° and 60° on a new constructed chair. Design: A test-retest reliability study. Subjects: One hundred healthy students male and female (mean age, 21y). Methods: Maximum isometric strength of the quadriceps and hamstring muscle groups was measured using the EPPD were recorded at 60° and 90° for 3 trials on 2 occasions. Reliability was assessed with the Intraclass correlation coefficient (ICC), mean and standard deviation (SD) of measurements, and smallest real differences were calculated for the maximum and for the mean and work of the 3 repetitions. Results: Mean strength ranged from 50.44 kg for knee flexion to 55.76 kg for knee extension 50.44 kg to 61.98 kg at 90° hip flexion. Test-retest reliability Intraclass correlation coefficients (ICCs) ranged from 0.85 to 0.99. ICCs for test-retest reliability ranged from 0.780 to 0.998. Conclusions: The results of the reliability study indicate that the EPPD in reliable dynamometer to use in determining lower limb muscle force production. It can be used to measure disease progression and to evaluate changes in knee extension and flexion strength at the individual patient level.
基金Liaoning Provincial Natural Science Foundation of China Under Grant No. 20052005
文摘This paper describes an investigation of a high-strength concrete frame reinforced with high-strength rebars that was tested in the structure engineering laboratory at Shenyang Jianzhu University. The frame specimen was pseudo- dynamically loaded to indicate three earthquake ground motions of different hazard levels, after which the test specimen was subjected to a pseudo-static loading. This paper focuses on the design, construction and experiment of the test frame and validation of the simulation models. Research shows that a high-strength concrete frame reinforced with high-strength rebars is more efficient and economical than a traditional reinforced concrete frame structure. In addition to the economies achieved by effective use of materials, research shows that the frame can provide enough strength to exceed conventional reinforced concrete frames and provide acceptable ductility. The test study provides evidence to validate the performance of a high- strength concrete frame designed according to current seismic code provisions. Based on previous test research, a nonlinear FEM analysis is completcd by using OpenSees software, The dynamic responses of the frame structure are numerically analyzed, The results of the numerical simulation show that the model can calculate the seismic responses of the frame by OpenSees. At the same time, the test provides additional opportunities to validate the performance of the simulation models.
基金National Natural Science Foundation of China(No.41967035)。
文摘Treatment of peat soil foundation in Yunnan surrounding Dianchi and Erhai Lakes poses complex problems for engineering projects.It is insufficient to rely on ordinary cement to reinforce peat soil.In order to make the reinforcement reliable,this experiment mixed(ultrafine cement)UFC into ordinary cement to form a composite solidify agent.This study aimed to analyze the influence of UFC proportion on the strength of cement-soil in the peat soil environment.Unconfined compressive strength(UCS)and scanning electron microscope(SEM)tests were conducted on samples soaked for 28 and 90 days,respectively.The test results show that without considering the effects of Humic Acid(HA)and Fulvic Acid(FA),incorporating UFC can significantly improve the UCS of cement-soil.The rapid hydration of the fine particles generates a large number of cementitious products,improves the cohesion of the soil skeleton,and fills the pores.However,when the proportion of UFC increases,the aggregate structure formed by a larger quantity of fine particles reduces the hydration rate and degree of cement hydration,making the UCS growth rate of cement-soil insignificant.In the peat soil environment,HA significantly weakened the UCS of cement-soil in both physical and chemical aspects.However,UFC can mitigate the adverse effect of HA on cement-soil by its small particle size,high surface energy,and solid binding ability.In addition,FA has a positive effect on the UCS of cement-soil soaked for 28 days and 90 days.The UFC addition could promote the enhancement effect of FA on cement-soil UCS.SEM test results showed that cement hydration products increased significantly with the increase of UFC proportion,and cementation between hydration products and soil particles was enhanced.The size and connectivity of cement-soil pores were significantly reduced,thereby improving cement-soil structural integrity.
