A Mg-8.2Gd-3.8Y-1.0Zn-0.4Zr(wt.%) alloy is processed by solution treatment and high pressure torsion(HPT) at room temperature to produce a nanostructured light material with high hardness. The stability of this alloy ...A Mg-8.2Gd-3.8Y-1.0Zn-0.4Zr(wt.%) alloy is processed by solution treatment and high pressure torsion(HPT) at room temperature to produce a nanostructured light material with high hardness. The stability of this alloy is subsequently tested through isochronal annealing for 0.5 h at 373 K to 673 K. The results reveal a thermal stability that is vastly superior to that of conventional Mg-based alloys processed by severe plastic deformation: the grain size remains at around 50 nm on heating to 573 K, and as the temperature is increased to 673 K,grain growth is restricted to within 500 nm. The stability of grain refinement of the present alloy/processing combination allowing grain size to be limited to 55 nm after exposure at 573 K, appears to be nearly one order of magnitude better than for the other SPD processed Mg-RE type alloys, and 2 orders of magnitude better than those of SPD processed RE-free Mg alloys. This superior thermal stability is attributed to formation of co-clusters near and segregation at grain boundaries, which cause a thermodynamic stabilization of grain size, as well as formation of β-Mg_(5)RE equilibrium phase at grain boundaries, which impede grain growth by the Zener pinning effect. The hardness of the nanostructured Mg-Gd-Y-Zn-Zr alloy increases with increasing annealing temperature up to 573 K, which is quite different from the other SPD-processed Mg-based alloys. The high hardness of 136 HV after annealing at 573 K is mainly due to solute segregation and solute clustering at or near grain boundaries.展开更多
Magnesium-based materials not only exhibit desirable characteristics such as low density and high specific strength, but also possess exceptional functional properties, including high damping capacity, high thermal co...Magnesium-based materials not only exhibit desirable characteristics such as low density and high specific strength, but also possess exceptional functional properties, including high damping capacity, high thermal conductivity, high electromagnetic interference shielding capacity, flame retardancy, and dissolvability. However, achieving a balance between strength and functional properties remains a significant challenge in Mg alloys community. Typically, strength depends on the pinning effect of defects, such as solute atoms and second phases,which hinder dislocation motion. On the other hand, optimal functional properties usually necessitate relative perfect crystal structures, as the presence of solute atoms and second phases can have adverse effects on damping capacity and thermal conductivity. Balancing these conflicting requirements is difficult. The trade-off between strength and functional properties of the Mg alloys should be broken to meet the urgent need in aerospace, automotive, 3C(computers, communications, and consumer electronics) and energy industries for high performance structural-functional integrated Mg-based materials. This review summarizes recent progress in understanding the mechanisms and influencing factors for the functional properties of Mg alloys. The mechanisms underlying the trade-off between strength and functional properties of Mg alloys is discussed. The latest developed structural-functional integrated Mg alloys and their composites are summarized, including high strength Mg-based materials with high damping capacity/high thermal conductivity/strong electromagnetic shielding capability/excellent flame-resistance/high dissolution rate. The future works of developing structure-function integrated Mg-based materials are proposed.展开更多
The interfacial microstructure and tensile properties of the squeeze cast SiCw/AZ91 Mg composites were characterized. There exist uniform, line and discrete MgO particles at the interface between SiC whisker and magn...The interfacial microstructure and tensile properties of the squeeze cast SiCw/AZ91 Mg composites were characterized. There exist uniform, line and discrete MgO particles at the interface between SiC whisker and magnesium in the composites using acid aluminum phosphate binder. The interfacial reaction products MgO are beneficial to interfacial bonding between SiCw and the Mg matrix. resulting in an improvement of the mechanical properties of the composite.展开更多
In this study,surface mechanical attrition treatment was employed to sucessfully produce a gradient nanostructured layer on WE43 magnesium alloy.X-ray diffraction,energy dispersive X-ray spectrometer,and high-resoluti...In this study,surface mechanical attrition treatment was employed to sucessfully produce a gradient nanostructured layer on WE43 magnesium alloy.X-ray diffraction,energy dispersive X-ray spectrometer,and high-resolution transmission electron microscope observations were mainly performed to uncover the microstructure evolution responsible for the refinement mechanisms.It reveals that the grain refinement process consists of three transition stages along the depth direction from the core matrix to the topmost surface layer,i.e.,dislocation cells and pile-ups,ultrafine subgrains,and randomly orientated nanograins with the grain size of~40 nm.Noticeably,the original Mg;RE second phase is also experienced refinement and then re-dissolved into the α-Mg matrix phase,forming a supersaturated solid solution nanostructuredα-Mg phase in the gradient refined layer.Due to the cooperative effects of grain refinement hardening,dislocation hardening,and supersaturated solid-solution hardening,the gradient nanostructured WE43 alloy contributes to the ultimate tensile strength of~435 MPa and ductility of~11.0%,showing an extraordinary strain hardening and mechanical properties among the reported severe plastic deformation-processed Mg alloys.This work provides a new strategy for the optimization of mechanical properties of Mg alloys via combining the gradient structure and supersaturated solid solution.展开更多
Magnesium alloys have shown prospective applications as a new biodegradable metal within bone. To garantee the longterm biocompatibility, a Mg-Zn-Ca alloy,composing of essential elements for human, was prepared and it...Magnesium alloys have shown prospective applications as a new biodegradable metal within bone. To garantee the longterm biocompatibility, a Mg-Zn-Ca alloy,composing of essential elements for human, was prepared and its feasibility for orthopedic applications was investigated. The in vitro and in vivo corrosion of Mg-Zn-Ca alloy as well as the biocompatibility were studied. The in vitro corrosion tests in five kinds of physiological solutions showed that the corrosion rates and corrosion morphologies of the alloy were strongly influenced by the solution used. The addition of serum in Hank’s and MEM significantly slowed down the corrosion rate and improved the corrosion uniformity of the alloy. The corrosion rate decreased with increasing serum concentration.The alloy showed the slowest corrosion rate as well as homogeneous corrosion morphology in MEM＋10%FBS. Both the indirect and direct cell experiments indicated good cytocompatibility of the extruded Mg-Zn-Ca alloy. In vivo, we observed a gradual degradation process from the surface of extruded Mg-Zn-Ca alloy and only 40% in volume of implant was left after 4 weeks implantation in medullary cavities of mice. The micro-CT and histological analyses revealed its good biocompatibility with peri-implant new bone formation and increasing cortical bone thickness with increasing implantation period. This study showed that the extruded MgZn-Ca alloy provided sufficient biocompatibility for orthopedic application, though the in vivo corrosion rate should be further reduced for clinical use.展开更多
A high strength Mg-5.1Zn-3.2Y-0.4Zr-0.4Ca （wt%） alloy containing W phase （Mg3Y2Zn3） prepared by permanent mold direct-chill casting is indirectly extruded at 350 ℃ and 400 ℃, respectively. The extruded alloys sh...A high strength Mg-5.1Zn-3.2Y-0.4Zr-0.4Ca （wt%） alloy containing W phase （Mg3Y2Zn3） prepared by permanent mold direct-chill casting is indirectly extruded at 350 ℃ and 400 ℃, respectively. The extruded alloys show bimodal grain structure consisting of fine dynamic recrystallized （DRXed） grains and unre- crystallized coarse regions containing fine W phase and β2′ precipitates. The fragmented W phase particles induced by extrusion stimulate nucleation of DRXed grains, leading to the formation of fine DRXed grains, which are mainly distributed near the W particle bands along the extrusion direction. The alloy extruded at 350 ℃ exhibits yield strength of 373 MPa, ultimate tensile strength of 403 MPa and elongation to failure of 5.1%. While the alloy extruded at 400 ℃ shows lower yield strength of 332 MPa, ultimate tensile strength of 352 MPa and higher elongation to failure of 12%. The mechanical properties of the as-extruded alloys vary with the distribution and size of W phase. A higher fraction of DRXed grains is obtained due to the homogeneous distribution of micron-scale broken W phase particles in the alloy extruded at 400 ℃, which can lead to higher ductility. In addition, the nano-scale dynamic W phase precipitates distributed in the unDRXed regions are refined at lower extrusion temperature. The smaller size of nano-scale W phase precipitates leads to a higher fraction of unDRXed regions which contributes to higher strength of the alloy extruded at 350 ℃.展开更多
基金supported by National Natural Science Foundation of China (No.U21A2047 and 51971076)China Postdoctoral Science Foundation (Grant No.2019M653599)Guangdong Basic and Applied Basic Research Foundation (No.2019A1515110289)。
文摘A Mg-8.2Gd-3.8Y-1.0Zn-0.4Zr(wt.%) alloy is processed by solution treatment and high pressure torsion(HPT) at room temperature to produce a nanostructured light material with high hardness. The stability of this alloy is subsequently tested through isochronal annealing for 0.5 h at 373 K to 673 K. The results reveal a thermal stability that is vastly superior to that of conventional Mg-based alloys processed by severe plastic deformation: the grain size remains at around 50 nm on heating to 573 K, and as the temperature is increased to 673 K,grain growth is restricted to within 500 nm. The stability of grain refinement of the present alloy/processing combination allowing grain size to be limited to 55 nm after exposure at 573 K, appears to be nearly one order of magnitude better than for the other SPD processed Mg-RE type alloys, and 2 orders of magnitude better than those of SPD processed RE-free Mg alloys. This superior thermal stability is attributed to formation of co-clusters near and segregation at grain boundaries, which cause a thermodynamic stabilization of grain size, as well as formation of β-Mg_(5)RE equilibrium phase at grain boundaries, which impede grain growth by the Zener pinning effect. The hardness of the nanostructured Mg-Gd-Y-Zn-Zr alloy increases with increasing annealing temperature up to 573 K, which is quite different from the other SPD-processed Mg-based alloys. The high hardness of 136 HV after annealing at 573 K is mainly due to solute segregation and solute clustering at or near grain boundaries.
基金partially supported by National Natural Science Foundation of China (No.U21A2047,No.51971076,and No.51771062)National Key Research and Development Program of China (No.2022YFE0109600)。
文摘Magnesium-based materials not only exhibit desirable characteristics such as low density and high specific strength, but also possess exceptional functional properties, including high damping capacity, high thermal conductivity, high electromagnetic interference shielding capacity, flame retardancy, and dissolvability. However, achieving a balance between strength and functional properties remains a significant challenge in Mg alloys community. Typically, strength depends on the pinning effect of defects, such as solute atoms and second phases,which hinder dislocation motion. On the other hand, optimal functional properties usually necessitate relative perfect crystal structures, as the presence of solute atoms and second phases can have adverse effects on damping capacity and thermal conductivity. Balancing these conflicting requirements is difficult. The trade-off between strength and functional properties of the Mg alloys should be broken to meet the urgent need in aerospace, automotive, 3C(computers, communications, and consumer electronics) and energy industries for high performance structural-functional integrated Mg-based materials. This review summarizes recent progress in understanding the mechanisms and influencing factors for the functional properties of Mg alloys. The mechanisms underlying the trade-off between strength and functional properties of Mg alloys is discussed. The latest developed structural-functional integrated Mg alloys and their composites are summarized, including high strength Mg-based materials with high damping capacity/high thermal conductivity/strong electromagnetic shielding capability/excellent flame-resistance/high dissolution rate. The future works of developing structure-function integrated Mg-based materials are proposed.
基金National Natllral S(tience l.'oundation of China (No. 59631080).
文摘The interfacial microstructure and tensile properties of the squeeze cast SiCw/AZ91 Mg composites were characterized. There exist uniform, line and discrete MgO particles at the interface between SiC whisker and magnesium in the composites using acid aluminum phosphate binder. The interfacial reaction products MgO are beneficial to interfacial bonding between SiCw and the Mg matrix. resulting in an improvement of the mechanical properties of the composite.
基金supported by National Natural Science Foundation of China(Nos.51701171 and 51971187)China Postdoctoral Science Foundation(No.2019M653599)+1 种基金the financial support from Partner State Key Laboratories in Hong Kong from the Innovation and Technology Commission(ITC)of the Government of the Hong Kong Special Administration Region(HKASR),China and the PolyU Research Office(Project Code:1-BBXA)supported by the grant from the PolyU Research Committee under student account code RK25
文摘In this study,surface mechanical attrition treatment was employed to sucessfully produce a gradient nanostructured layer on WE43 magnesium alloy.X-ray diffraction,energy dispersive X-ray spectrometer,and high-resolution transmission electron microscope observations were mainly performed to uncover the microstructure evolution responsible for the refinement mechanisms.It reveals that the grain refinement process consists of three transition stages along the depth direction from the core matrix to the topmost surface layer,i.e.,dislocation cells and pile-ups,ultrafine subgrains,and randomly orientated nanograins with the grain size of~40 nm.Noticeably,the original Mg;RE second phase is also experienced refinement and then re-dissolved into the α-Mg matrix phase,forming a supersaturated solid solution nanostructuredα-Mg phase in the gradient refined layer.Due to the cooperative effects of grain refinement hardening,dislocation hardening,and supersaturated solid-solution hardening,the gradient nanostructured WE43 alloy contributes to the ultimate tensile strength of~435 MPa and ductility of~11.0%,showing an extraordinary strain hardening and mechanical properties among the reported severe plastic deformation-processed Mg alloys.This work provides a new strategy for the optimization of mechanical properties of Mg alloys via combining the gradient structure and supersaturated solid solution.
基金supported by the National Natural Science Foundation of China(51401007,11472032,11120101001 and 11421202)a foundation for the author of the National Excellent Doctoral Dissertation of China(201463)+1 种基金Young Elite Scientists Sponsorship Program By CAST(2017QNRC001)the National Key Research and Development Plan(2016YFC1102203 and 2016YFC1101100)
文摘Magnesium alloys have shown prospective applications as a new biodegradable metal within bone. To garantee the longterm biocompatibility, a Mg-Zn-Ca alloy,composing of essential elements for human, was prepared and its feasibility for orthopedic applications was investigated. The in vitro and in vivo corrosion of Mg-Zn-Ca alloy as well as the biocompatibility were studied. The in vitro corrosion tests in five kinds of physiological solutions showed that the corrosion rates and corrosion morphologies of the alloy were strongly influenced by the solution used. The addition of serum in Hank’s and MEM significantly slowed down the corrosion rate and improved the corrosion uniformity of the alloy. The corrosion rate decreased with increasing serum concentration.The alloy showed the slowest corrosion rate as well as homogeneous corrosion morphology in MEM＋10%FBS. Both the indirect and direct cell experiments indicated good cytocompatibility of the extruded Mg-Zn-Ca alloy. In vivo, we observed a gradual degradation process from the surface of extruded Mg-Zn-Ca alloy and only 40% in volume of implant was left after 4 weeks implantation in medullary cavities of mice. The micro-CT and histological analyses revealed its good biocompatibility with peri-implant new bone formation and increasing cortical bone thickness with increasing implantation period. This study showed that the extruded MgZn-Ca alloy provided sufficient biocompatibility for orthopedic application, though the in vivo corrosion rate should be further reduced for clinical use.
基金supported financially by the National Key Research and Development Program of China (No. 2016YFB0301102)the National Natural Science Foundation of China (No. 51571068)
文摘A high strength Mg-5.1Zn-3.2Y-0.4Zr-0.4Ca （wt%） alloy containing W phase （Mg3Y2Zn3） prepared by permanent mold direct-chill casting is indirectly extruded at 350 ℃ and 400 ℃, respectively. The extruded alloys show bimodal grain structure consisting of fine dynamic recrystallized （DRXed） grains and unre- crystallized coarse regions containing fine W phase and β2′ precipitates. The fragmented W phase particles induced by extrusion stimulate nucleation of DRXed grains, leading to the formation of fine DRXed grains, which are mainly distributed near the W particle bands along the extrusion direction. The alloy extruded at 350 ℃ exhibits yield strength of 373 MPa, ultimate tensile strength of 403 MPa and elongation to failure of 5.1%. While the alloy extruded at 400 ℃ shows lower yield strength of 332 MPa, ultimate tensile strength of 352 MPa and higher elongation to failure of 12%. The mechanical properties of the as-extruded alloys vary with the distribution and size of W phase. A higher fraction of DRXed grains is obtained due to the homogeneous distribution of micron-scale broken W phase particles in the alloy extruded at 400 ℃, which can lead to higher ductility. In addition, the nano-scale dynamic W phase precipitates distributed in the unDRXed regions are refined at lower extrusion temperature. The smaller size of nano-scale W phase precipitates leads to a higher fraction of unDRXed regions which contributes to higher strength of the alloy extruded at 350 ℃.
