To investigate the effect of solidification parameters on the solidification path and microstructure evolution of Ti-45Al-5Nb(at.%) alloy, Bridgman-type directional solidification and thermodynamics calculations were ...To investigate the effect of solidification parameters on the solidification path and microstructure evolution of Ti-45Al-5Nb(at.%) alloy, Bridgman-type directional solidification and thermodynamics calculations were performed on the alloy. The microstructures, micro-segregation and solidification path were investigated.The results show that the β phase is the primary phase of the alloy at growth rates of 5-20 μm·s^(-1) under the temperature gradients of 15-20 K·mm^(-1), and the primary phase is transformed into an α phase at relatively higher growth rates(V >20 μm·s^(-1)). The mainly S-segregation and β-segregation can be observed in Ti-45Al-5Nb alloy at a growth rate of 10 μm·s^(-1) under a temperature gradient of 15 K·mm^(-1). The increase of temperature gradient to 20 K·mm^(-1) can eliminate β-segregation, but has no obvious effect on S-segregation. The results also show that 5 at.% Nb addition can expand the β phase region, increase the melting point of the alloy and induce the solidification path to become complicated. The equilibrium solidification path of Ti-45Al-5Nb alloy can be described as L L→β L+β L+β→αα+β_R β→ααα→γα+γα→α_2+γγ_R+(α_2+γ), in which β_R and γ_R mean the residual β and展开更多
ZL205 A alloys with large thin-walled shape were continuously processed by coupling travelling magnetic fields(TMF)with sequential solidification,to eliminate the shrinkage defects and optimize the mechanical performa...ZL205 A alloys with large thin-walled shape were continuously processed by coupling travelling magnetic fields(TMF)with sequential solidification,to eliminate the shrinkage defects and optimize the mechanical performance.Through experiments and simulations,the parameter optimization of TMF and the influence on feeding behavior,microstructure and properties were systematically studied.The results indicate that the magnetic force maximizes at the excitation current of 20 A and frequency of 200 Hz under the experimental conditions of this study,and increases from center to side-walls,which is more convenient to process thin-walled castings.TMF can break secondary dendritic arm and dendrites overlaps,widen feeding channels,prolong the feeding time,optimize the feeding paths,eliminate shrinkage defects and improve properties.Specifically,for as-cast state,TMF with excitation current of 20 A increases ultimate tensile strength,elongation and micro-hardness from 186 MPa,7.3%and 82.1 kg/mm^(2) to 221 MPa,11.7%and 100.5 kg/mm^(2),decreases porosity from 1.71%to 0.22%,and alters brittle fracture to ductile fracture.展开更多
Five equiatomic alloys(Ti Zr Hf VNb, Ti Zr Hf VTa, Ti Zr Nb Mo V, Ti Zr Hf Mo V and Zr Nb Mo Hf V) composed of five elements with high melting temperature, respectively were prepared by arc-melting to develop a novel ...Five equiatomic alloys(Ti Zr Hf VNb, Ti Zr Hf VTa, Ti Zr Nb Mo V, Ti Zr Hf Mo V and Zr Nb Mo Hf V) composed of five elements with high melting temperature, respectively were prepared by arc-melting to develop a novel high temperature alloy. The five alloys exhibit different dendritic and interdendritic morphologies. The Ti Zr Hf VNb, Ti Zr Hf VTa and Ti Zr Nb Mo V alloys formed disordered solid solution phases with body-centered cubic structure, and exhibited high compressive strength and good plasticity. The Ti Zr Hf Mo V and Zr Nb Mo Hf V alloys are composed with Laves phase(Hf Mo2) and disordered solid solution phases with body-centered cubic structure. The Ti Zr Hf Mo V and Zr Nb Mo Hf V alloys are harder and more brittle than the other three alloys due to the existence of hard and brittle Laves phases. At high temperatures, the strength decreases to below 300 MPa for the Ti Zr Hf VNb and Ti Zr Hf Mo V alloys. Solution strengthening is the primary strengthening mechanism of the Ti Zr Hf VNb, Ti Zr Hf VTa and Ti Zr Nb Mo V alloys, and brittle Laves phase is the main cause for the low ductility of the Ti Zr Hf Mo V and Zr Nb Mo Hf V alloys.展开更多
Microstructural improvement of Al-Cu-Li alloys with high Li content plays a critical role for the acquisition of excellent mechanical properties and ultra-low density.In this regard,the Al-Cu-Li alloy castings with hi...Microstructural improvement of Al-Cu-Li alloys with high Li content plays a critical role for the acquisition of excellent mechanical properties and ultra-low density.In this regard,the Al-Cu-Li alloy castings with high Li content from 1.5 wt.%to 4.5 wt.%were prepared by near-rapid solidification,followed by two-stage homogenization treatment(490℃/16 h and 530℃/16 h).The microstructural evolution and solidification behavior of the as-cast and homogenized alloys with different Li contents were systematically studied by combining experiments with calculations by Pandat software.The results indicate that with the increase of Li content,the grain sizes decrease,the solution ability of Cu in the matrixα-Al phase increases,while the content of secondary dendrites increases and the precipitated phases change from low melting point phases to high melting point phases under the near-rapid solidification.Additionally,by the coupling of near-rapid solidification and two-stage homogenization,the metastable precipitated phases(Al7Cu4Li and AlCu3)can be dissolved effectively in the alloys with Li content of 1.5 wt.%-2.5 wt.%;moreover,the stable precipitated phases(Al6CuLi3 and Al2CuLi)uniformly distribute at the grain boundaries in the alloys with Li content of 3.5 wt.%-4.5 wt.%.As a result,the refined and homogenized microstructure can be obtained.展开更多
The effect of growth rates (V=2-50 μm·s-1) on microstructure and microhardness of directionally solidified Ti-44Al-5Nb-1.5Cr-1.5Zr-1Mo-0.1B (at.%) alloy at a constant temperature gradient (G=18 K·mm-1) was ...The effect of growth rates (V=2-50 μm·s-1) on microstructure and microhardness of directionally solidified Ti-44Al-5Nb-1.5Cr-1.5Zr-1Mo-0.1B (at.%) alloy at a constant temperature gradient (G=18 K·mm-1) was investigated. Results indicated that β phase was the primary phase of the directionally solidified Ti-44Al-5Nb-1.5Cr-1.5Zr-1Mo-0.1B alloy. As the growth rate increases, the solid/liquid interface turns from cellular growth to dendric growth. The interlamellar spacing (λs) decreases with the increase of growth rate according to the relationship of λs=3.39V -0.31. The solidification segregation occurs due to the enrichment of β-stabilizing element Nb, Cr in primary β phase during solidification;moreover, the degree of the segregation increases with the growth rate, resulting in the emergence of B2 phase in lamellar colonies at high growth rates. The microhardness (Hv) grows with the growth rate based on the equation of HV=328.69V 0.072, which mainly attributes to the microstructure refinement.展开更多
Inconel 718 alloys were fabricated by selective laser melting under different scanning speeds to investigate the change of the morphology of molten pool,direction of grain growth,and tensile properties.Results show th...Inconel 718 alloys were fabricated by selective laser melting under different scanning speeds to investigate the change of the morphology of molten pool,direction of grain growth,and tensile properties.Results show that as the scanning speed increases from 1,000 to 1,450 mm·s^(-1),the ratio between depth and width of molten pool increases,yet their overlapping regimes decrease.Meanwhile,increasing scanning speed can promote the solidified structure evolve from cell to columnar dendrites,and decrease the dendrite spacing from 0.54 to 0.39 μm;the average columnar grain size also decreases from 84.42 to 73.51 μm.At different scanning speeds,the preferred orientation of grains along the building is mainly <001> direction.In addition,the tensile properties of samples under different scanning speeds present a non-monotonic transition.The maximum ultimate tensile strength and elongation can reach 1,014±19 MPa and 19.04±1.12 (%),respectively,at the scanning speed of 1,300 mm·s^(-1).展开更多
The effect of excitation current intensity on the mechanical properties of ZL205 A castings solidified under a traveling magnetic field was studied. The results of the experiment indicate that the excitation current i...The effect of excitation current intensity on the mechanical properties of ZL205 A castings solidified under a traveling magnetic field was studied. The results of the experiment indicate that the excitation current intensity of the traveling magnetic field has a great influence on the mechanical properties of the ZL205 A castings. When the excitation current intensity is 15 A, the tensile strength and elongation of ZL205 A alloy castings increase 27.2% and 67.7%, respectively, compared with those of the same alloy solidified under gravity. The improvement of mechanical properties is attributed to the decrease of micro-porosity in the alloy. Under the traveling magnetic field, the feeding pressure in the alloy melt before solidification can be enhanced due to the electromagnetic force. Moreover, the melt flow induced by the traveling magnetic field can decrease the temperature gradient. The feeding resistance will be increased because the temperature gradient decrease. So traveling magnetic field has an optimum effect on feeding.展开更多
Arc melting was utilized in this study to produce Zr_(55)Cu_(30)Ni_5Al_(10) alloys under mixed atmospheres with various ratios of high-purity hydrogen to argon. The influences of hydrogen addition on the solidificatio...Arc melting was utilized in this study to produce Zr_(55)Cu_(30)Ni_5Al_(10) alloys under mixed atmospheres with various ratios of high-purity hydrogen to argon. The influences of hydrogen addition on the solidification structure and glass-forming ability of Zr_(55)Cu_(30)Ni_5Al_(10) alloy were determined by examining microstructures in different parts of the cast ingots. The results showed that different degrees of crystallization structures were obtained in the ascast button ingots after arc melting in high-purity Ar, and the cross-sectional solidification morphology of arcmelted ingots was found to consist of crystals with varying from the bottom up. By contrast, there were completely amorphous structures in the middle and upper areas of the as-cast button ingots fabricated by adding 10% H_2 to the high-purity Ar atmosphere. A clear solidification interface was found between the crystal and glass in the ascast button ingots, which indicates that hydrogen addition can enhance the Zr_(55)Cu_(30)Ni_5Al_(10) alloy's glass-forming ability. The precise mechanism responsible for this was also investigated.展开更多
A turtle carapace bio-inspired Ti matrix hybrid composite was successfully fabricated in this work. This composite incorporates two parts： the Ti-Al intermetallic multilayered composite and continuous SiC fibers-rein...A turtle carapace bio-inspired Ti matrix hybrid composite was successfully fabricated in this work. This composite incorporates two parts： the Ti-Al intermetallic multilayered composite and continuous SiC fibers-reinforced Ti matrix composite. In the Ti-Al intermetallic multilayered composite part, a series of Ti-Al intermetallics compounds, including Ti3Al, TiAl, TiAl2 and TiAl3, were formed between the Ti layers. In the continuous SiC fibers-reinforced Ti matrix composite part, SiC fibers and Ti matrix were found to be bonded well through weak interface reaction. Flexural strength of this material reached 1.21 ±0.16 GPa, measured by three-point bending test. The deformation features suggest that the hierarchical structure combining ductile Ti layers/matrix with brittle high-strength Ti-Al intermetallics layers/SiC fibers can effectively enhance the mechanical properties of the bio-inspired hybrid composite.展开更多
The Nb-16Si-18Ti-xB(at%,similarly hereinafter,x=0,1,2,3)alloys were prepared by arc melting in a water-cooled copper crucible.The influences of B addition on their microstructures and properties were based on the data...The Nb-16Si-18Ti-xB(at%,similarly hereinafter,x=0,1,2,3)alloys were prepared by arc melting in a water-cooled copper crucible.The influences of B addition on their microstructures and properties were based on the data of X-ray diffraction(XRD),field emission scanning electron microscopy(FESEM),and electronic universal material testing machine.It is found that the addition of B promotes the formation ofα-Nb5Si3phase and suppresses the formation of Nb3Si phase.B addition also tends Nb-16Si-18Ti alloy to form the hypereutectic structures.The content of silicide phases shows a trend of firstly decreasing and then increasing in Nb-16Si-18Ti-xB(x=0,1,2,3)alloys.The size of Nb solid solution(Nbss)phase increases in Nb-16Si-18Ti-xB(x=0,1,2,3)alloys after heat treatment at 1523 K for 10 h.The room temperature compression strength of Nb-16Si-18Ti alloy increases firstly and then decreases with B addition.The high-temperature compression strength of Nb-16Si-18Ti alloy decreases firstly and then increases with B addition.It is found that the volume and size of silicide phases have a synergistic effect on the compression strength of Nb-TiSi-based alloys.展开更多
基金financially supported by the National Natural Science Foundation of China(Nos.51331005 and 51425402)
文摘To investigate the effect of solidification parameters on the solidification path and microstructure evolution of Ti-45Al-5Nb(at.%) alloy, Bridgman-type directional solidification and thermodynamics calculations were performed on the alloy. The microstructures, micro-segregation and solidification path were investigated.The results show that the β phase is the primary phase of the alloy at growth rates of 5-20 μm·s^(-1) under the temperature gradients of 15-20 K·mm^(-1), and the primary phase is transformed into an α phase at relatively higher growth rates(V >20 μm·s^(-1)). The mainly S-segregation and β-segregation can be observed in Ti-45Al-5Nb alloy at a growth rate of 10 μm·s^(-1) under a temperature gradient of 15 K·mm^(-1). The increase of temperature gradient to 20 K·mm^(-1) can eliminate β-segregation, but has no obvious effect on S-segregation. The results also show that 5 at.% Nb addition can expand the β phase region, increase the melting point of the alloy and induce the solidification path to become complicated. The equilibrium solidification path of Ti-45Al-5Nb alloy can be described as L L→β L+β L+β→αα+β_R β→ααα→γα+γα→α_2+γγ_R+(α_2+γ), in which β_R and γ_R mean the residual β and
基金financial supports from the National Key Research and Development Program of China(2017YFA0403804)the National Natural Science Foundation of China(51425402,51671073)。
文摘ZL205 A alloys with large thin-walled shape were continuously processed by coupling travelling magnetic fields(TMF)with sequential solidification,to eliminate the shrinkage defects and optimize the mechanical performance.Through experiments and simulations,the parameter optimization of TMF and the influence on feeding behavior,microstructure and properties were systematically studied.The results indicate that the magnetic force maximizes at the excitation current of 20 A and frequency of 200 Hz under the experimental conditions of this study,and increases from center to side-walls,which is more convenient to process thin-walled castings.TMF can break secondary dendritic arm and dendrites overlaps,widen feeding channels,prolong the feeding time,optimize the feeding paths,eliminate shrinkage defects and improve properties.Specifically,for as-cast state,TMF with excitation current of 20 A increases ultimate tensile strength,elongation and micro-hardness from 186 MPa,7.3%and 82.1 kg/mm^(2) to 221 MPa,11.7%and 100.5 kg/mm^(2),decreases porosity from 1.71%to 0.22%,and alters brittle fracture to ductile fracture.
基金financially supported by the 973 project(2011CB610406)Natural Science Foundation of Hei Longjiang Province(JC201209)
文摘Five equiatomic alloys(Ti Zr Hf VNb, Ti Zr Hf VTa, Ti Zr Nb Mo V, Ti Zr Hf Mo V and Zr Nb Mo Hf V) composed of five elements with high melting temperature, respectively were prepared by arc-melting to develop a novel high temperature alloy. The five alloys exhibit different dendritic and interdendritic morphologies. The Ti Zr Hf VNb, Ti Zr Hf VTa and Ti Zr Nb Mo V alloys formed disordered solid solution phases with body-centered cubic structure, and exhibited high compressive strength and good plasticity. The Ti Zr Hf Mo V and Zr Nb Mo Hf V alloys are composed with Laves phase(Hf Mo2) and disordered solid solution phases with body-centered cubic structure. The Ti Zr Hf Mo V and Zr Nb Mo Hf V alloys are harder and more brittle than the other three alloys due to the existence of hard and brittle Laves phases. At high temperatures, the strength decreases to below 300 MPa for the Ti Zr Hf VNb and Ti Zr Hf Mo V alloys. Solution strengthening is the primary strengthening mechanism of the Ti Zr Hf VNb, Ti Zr Hf VTa and Ti Zr Nb Mo V alloys, and brittle Laves phase is the main cause for the low ductility of the Ti Zr Hf Mo V and Zr Nb Mo Hf V alloys.
基金the National Key Research and Development Program of China(Grant No.2017YFA0403804)the National Natural Science Foundation of China(Grant No.51425402)。
文摘Microstructural improvement of Al-Cu-Li alloys with high Li content plays a critical role for the acquisition of excellent mechanical properties and ultra-low density.In this regard,the Al-Cu-Li alloy castings with high Li content from 1.5 wt.%to 4.5 wt.%were prepared by near-rapid solidification,followed by two-stage homogenization treatment(490℃/16 h and 530℃/16 h).The microstructural evolution and solidification behavior of the as-cast and homogenized alloys with different Li contents were systematically studied by combining experiments with calculations by Pandat software.The results indicate that with the increase of Li content,the grain sizes decrease,the solution ability of Cu in the matrixα-Al phase increases,while the content of secondary dendrites increases and the precipitated phases change from low melting point phases to high melting point phases under the near-rapid solidification.Additionally,by the coupling of near-rapid solidification and two-stage homogenization,the metastable precipitated phases(Al7Cu4Li and AlCu3)can be dissolved effectively in the alloys with Li content of 1.5 wt.%-2.5 wt.%;moreover,the stable precipitated phases(Al6CuLi3 and Al2CuLi)uniformly distribute at the grain boundaries in the alloys with Li content of 3.5 wt.%-4.5 wt.%.As a result,the refined and homogenized microstructure can be obtained.
基金This research was financially supported by the National Key Research and Development Program of China(Grant No.2016YFB0301201)National Natural Science Foundation of China(Grant Nos.51671073,51425402)+2 种基金Fundamental Research and Development Program of China(Grant No.JCKY2017205B032)Yunnan Rare Metal Materials Genetic Engineering Project(Grant No.2018ZE013)Major Special Science and Technology Project ofYunnan Province(Grant No.2019ZE001).
文摘The effect of growth rates (V=2-50 μm·s-1) on microstructure and microhardness of directionally solidified Ti-44Al-5Nb-1.5Cr-1.5Zr-1Mo-0.1B (at.%) alloy at a constant temperature gradient (G=18 K·mm-1) was investigated. Results indicated that β phase was the primary phase of the directionally solidified Ti-44Al-5Nb-1.5Cr-1.5Zr-1Mo-0.1B alloy. As the growth rate increases, the solid/liquid interface turns from cellular growth to dendric growth. The interlamellar spacing (λs) decreases with the increase of growth rate according to the relationship of λs=3.39V -0.31. The solidification segregation occurs due to the enrichment of β-stabilizing element Nb, Cr in primary β phase during solidification;moreover, the degree of the segregation increases with the growth rate, resulting in the emergence of B2 phase in lamellar colonies at high growth rates. The microhardness (Hv) grows with the growth rate based on the equation of HV=328.69V 0.072, which mainly attributes to the microstructure refinement.
基金financially supported by the National Natural Science Foundation of China(Grant Nos.51425402 and 51501048)。
文摘Inconel 718 alloys were fabricated by selective laser melting under different scanning speeds to investigate the change of the morphology of molten pool,direction of grain growth,and tensile properties.Results show that as the scanning speed increases from 1,000 to 1,450 mm·s^(-1),the ratio between depth and width of molten pool increases,yet their overlapping regimes decrease.Meanwhile,increasing scanning speed can promote the solidified structure evolve from cell to columnar dendrites,and decrease the dendrite spacing from 0.54 to 0.39 μm;the average columnar grain size also decreases from 84.42 to 73.51 μm.At different scanning speeds,the preferred orientation of grains along the building is mainly <001> direction.In addition,the tensile properties of samples under different scanning speeds present a non-monotonic transition.The maximum ultimate tensile strength and elongation can reach 1,014±19 MPa and 19.04±1.12 (%),respectively,at the scanning speed of 1,300 mm·s^(-1).
基金financially supported by the National Basic Research Program of China(2011CB610406)the Natural Science Foundation of Hei Longjiang Province(JC201209)the National Natural Science Foundation of China(51425402)
文摘The effect of excitation current intensity on the mechanical properties of ZL205 A castings solidified under a traveling magnetic field was studied. The results of the experiment indicate that the excitation current intensity of the traveling magnetic field has a great influence on the mechanical properties of the ZL205 A castings. When the excitation current intensity is 15 A, the tensile strength and elongation of ZL205 A alloy castings increase 27.2% and 67.7%, respectively, compared with those of the same alloy solidified under gravity. The improvement of mechanical properties is attributed to the decrease of micro-porosity in the alloy. Under the traveling magnetic field, the feeding pressure in the alloy melt before solidification can be enhanced due to the electromagnetic force. Moreover, the melt flow induced by the traveling magnetic field can decrease the temperature gradient. The feeding resistance will be increased because the temperature gradient decrease. So traveling magnetic field has an optimum effect on feeding.
基金supported by the National Natural Science Foundation of China(51401129,51371066)China Postdoctoral Science Foundation(2015M571327)the Educational Commission of Liaoning Province(L2014052,LGD2016018)
文摘Arc melting was utilized in this study to produce Zr_(55)Cu_(30)Ni_5Al_(10) alloys under mixed atmospheres with various ratios of high-purity hydrogen to argon. The influences of hydrogen addition on the solidification structure and glass-forming ability of Zr_(55)Cu_(30)Ni_5Al_(10) alloy were determined by examining microstructures in different parts of the cast ingots. The results showed that different degrees of crystallization structures were obtained in the ascast button ingots after arc melting in high-purity Ar, and the cross-sectional solidification morphology of arcmelted ingots was found to consist of crystals with varying from the bottom up. By contrast, there were completely amorphous structures in the middle and upper areas of the as-cast button ingots fabricated by adding 10% H_2 to the high-purity Ar atmosphere. A clear solidification interface was found between the crystal and glass in the ascast button ingots, which indicates that hydrogen addition can enhance the Zr_(55)Cu_(30)Ni_5Al_(10) alloy's glass-forming ability. The precise mechanism responsible for this was also investigated.
基金financially supported by the Defense Industrial Technology Development Program(JCKY2017205B032)National Natural Science Foundation of China(Nos.51405458,51371066 and 51331005)
文摘A turtle carapace bio-inspired Ti matrix hybrid composite was successfully fabricated in this work. This composite incorporates two parts： the Ti-Al intermetallic multilayered composite and continuous SiC fibers-reinforced Ti matrix composite. In the Ti-Al intermetallic multilayered composite part, a series of Ti-Al intermetallics compounds, including Ti3Al, TiAl, TiAl2 and TiAl3, were formed between the Ti layers. In the continuous SiC fibers-reinforced Ti matrix composite part, SiC fibers and Ti matrix were found to be bonded well through weak interface reaction. Flexural strength of this material reached 1.21 ±0.16 GPa, measured by three-point bending test. The deformation features suggest that the hierarchical structure combining ductile Ti layers/matrix with brittle high-strength Ti-Al intermetallics layers/SiC fibers can effectively enhance the mechanical properties of the bio-inspired hybrid composite.
基金financially supported by the National Natural Science Foundation of China(Nos.51425402,51405458,51371066 and 51671073)the National Key Research and Development Program of China(No.2016YFB0301201)the Youth Science Foundation of Heilongjiang Province(No.QC2013C049)。
文摘The Nb-16Si-18Ti-xB(at%,similarly hereinafter,x=0,1,2,3)alloys were prepared by arc melting in a water-cooled copper crucible.The influences of B addition on their microstructures and properties were based on the data of X-ray diffraction(XRD),field emission scanning electron microscopy(FESEM),and electronic universal material testing machine.It is found that the addition of B promotes the formation ofα-Nb5Si3phase and suppresses the formation of Nb3Si phase.B addition also tends Nb-16Si-18Ti alloy to form the hypereutectic structures.The content of silicide phases shows a trend of firstly decreasing and then increasing in Nb-16Si-18Ti-xB(x=0,1,2,3)alloys.The size of Nb solid solution(Nbss)phase increases in Nb-16Si-18Ti-xB(x=0,1,2,3)alloys after heat treatment at 1523 K for 10 h.The room temperature compression strength of Nb-16Si-18Ti alloy increases firstly and then decreases with B addition.The high-temperature compression strength of Nb-16Si-18Ti alloy decreases firstly and then increases with B addition.It is found that the volume and size of silicide phases have a synergistic effect on the compression strength of Nb-TiSi-based alloys.
