Al was prepared by a new method in molten salt at low temperature. Sintered alumina pellets were used as cathode; graphite rod was employed as anode; and the molten CaCl2-NaCl was the electrolyte. A constant 3.2 V vol...Al was prepared by a new method in molten salt at low temperature. Sintered alumina pellets were used as cathode; graphite rod was employed as anode; and the molten CaCl2-NaCl was the electrolyte. A constant 3.2 V voltage was applied in this experiment, and oxygen in solid alumina cathode was reduced by direct electrochemical deoxidation at 550℃. In this process, the current gradually decreased with increasing time and the alumina pellets became grey and porous. The metallic particles were obtained and characterized by XRD （X-ray diffraction） and SEM （scanning electron microscopy）.展开更多
Stress concentration occurs in the foundations of railway tracks where discontinuous components are located.The exacerbated stress under the expansion joints in slab tracks may trigger foundation failures such as mud ...Stress concentration occurs in the foundations of railway tracks where discontinuous components are located.The exacerbated stress under the expansion joints in slab tracks may trigger foundation failures such as mud pumping.Although the higher stress due to the discontinuities of track structures has been discussed in past studies,few focused on the stress response of roadbeds in slab tracks and quantitatively characterized the stress pattern.In this paper,we performed a dynamic finite element analysis of a track-formation system,incorporating expansion joints as primary longitudinal discontinuities.The configurations of CRTS Ⅲ slab tracks and the contact conditions between concrete layers were considered.Numerical results show that longitudinal influencing length of induced stress on roadbed under wheel load relates to the contact conditions between concrete layers,increasing nonlinearly at a larger coefficient of friction.Given a measured coefficient of friction of 0.7,the calculated longitudinal influencing length(9.0 m) matches with field data.The longitudinal influencing length is not affected with the increasing velocity.As stress concentration arises with expansion joints,the worstcase scenario emerges when double-axle loads are exerted immediately above the expansion joints between concrete bases.A stress concentration factor Cvon the roadbed is proposed;it increases with the increasing velocity,changing from 1.33 to 1.52 at velocities between 5 and 400 km/h.The stress distribution on roadbeds transforms from a trapezoid pattern at continuous sections to a triangle pattern at points with longitudinal discontinuities.An explicit expression is finally proposed for the stress pattern on roadbed under expansion joints.Although structural discontinuities induce stress raiser,the extent of concentration is mitigated with increasing depth at different velocity levels.展开更多
Silicon(Si)and carbon(C)composites hold the promise for replacing the commercial graphite anode,thus increasing the energy density of lithium-ion batteries(LIBs).To mitigate the formation of SiC,this paper reports a m...Silicon(Si)and carbon(C)composites hold the promise for replacing the commercial graphite anode,thus increasing the energy density of lithium-ion batteries(LIBs).To mitigate the formation of SiC,this paper reports a molten salt electrolysis approach to prepare C-Si composite by the electrolysis of C-SiO2 composites.Unlike the conventional way of making a C coating on Si,C-SiO2 composites were prepared by pyrolyzing the low-cost sucrose and silica.The electrochemical deoxidation of the C-SiO2 composites not only produces nanostructured Si inside the C matrix but also introduces voids between the C and Si owing to the volume shrinkage from converting SiO2 to Si.More importantly,the use of Mg ion-containing molten salts precludes the generation of SiC,and the electrolytic Si@C composite anode delivers a capacity of about 1500 mAh g-1 after 100 cycles at a current density of 500 mA g-1.Further,the Si@C‖LiNi0.6Co0.2Mn0.2O2 full cell delivers a high energy density of 608 Wh kg-1.Overall,the molten salt approach provides a one-step electrochemical way to convert oxides@C to metals@C functional materials.展开更多
A Bayesian method for estimating human error probability（HEP） is presented.The main idea of the method is incorporating human performance data into the HEP estimation process.By integrating human performance data an...A Bayesian method for estimating human error probability（HEP） is presented.The main idea of the method is incorporating human performance data into the HEP estimation process.By integrating human performance data and prior information about human performance together,a more accurate and specific HEP estimation can be achieved.For the time-unrelated task without rigorous time restriction,the HEP estimated by the common-used human reliability analysis（HRA） methods or expert judgments is collected as the source of prior information.And for the time-related task with rigorous time restriction,the human error is expressed as non-response making.Therefore,HEP is the time curve of non-response probability（NRP）.The prior information is collected from system safety and reliability specifications or by expert judgments.The（joint） posterior distribution of HEP or NRP-related parameter（s） is constructed after prior information has been collected.Based on the posterior distribution,the point or interval estimation of HEP/NRP is obtained.Two illustrative examples are introduced to demonstrate the practicality of the aforementioned approach.展开更多
The spatial resolution of the gamma-rays camera was measured on a60Co gamma-rays source with edge method. The gamma-rays camera is consisting with rays-fluorescence convertor, optical imaging system, MCP image intensi...The spatial resolution of the gamma-rays camera was measured on a60Co gamma-rays source with edge method. The gamma-rays camera is consisting with rays-fluorescence convertor, optical imaging system, MCP image intensifier, CCD camera, electronic control system and other devices, and is mainly used in the image diagnostics of the intense pulse radiation sources [1]. Due to the relatively big quantum detective efficiency (DQE) and quantum gain of the gamma-rays, etc., the experimental data were processed by averaging multiple images and fitting curves. According to the experimental results, the spatial resolution MTF (modulation transfer function) at the 10% intensity was about 2lp/mm. Meanwhile, because of the relatively big dispersion effects of the fluorescence transmissions in the scintillator and the optical imaging system, the maximal single-noise ratio (SNR) of the camera was found to be about 5:1. In addition, the spatial resolution of the camera was measured with pulse X-rays with 0.3MeV in average energy and exclusion of the effects of secondary electrons from consideration. Accordingly, the spatial resolution MTF at the 10% intensity was about 5lp/mm. This could be an additional evidence to verify the effects of secondary electrons induced by the 1.25MeV gamma-rays in the scintillator upon the spatial resolution. Based on our analysis, the dispersion sizes of the secondary electrons in the scintillator are about 0.4mm-0.6mm. Comparatively, as indicated by the detailed analysis of the spatial resolutions of the MCP image intensifier and CCD devices, both of them have little effect on the spatial resolution of the gamma-rays camera that could be well neglected.展开更多
The diagnostic methods for the profile of the radiation source were estab-lished at first based on the pinhole imaging principle. In this paper, the relationships among various parameters of the gamma-rays crammer suc...The diagnostic methods for the profile of the radiation source were estab-lished at first based on the pinhole imaging principle. In this paper, the relationships among various parameters of the gamma-rays crammer such as the modulation transfer function (MTF), the noise power spectrum (NPS), the signal-noise ratio (SNR) and the detective quantum efficiency (DQE) are developed and studied experimentally on the cobalt radiation source. The image diagnostic system is consisting with rays-fluorescence convertor (YAG crystal), optical imaging system, MCP image intensifier, CCD camera and other devices. The spatial resolution of the modulation transfer function (MTF) at 10% intensity was measured as 1 lp/mm by knife-edge method. The quantum of the measurement system is about 150 under weak radiation condition due to the single particle detection efficiency of the system. The dynamic range was inferred preliminarily as about 437. The required radiation intensity was calculated using the experiment result for the (SNR) = 1, 5, 10, respectively. The theoretical investigation results show that the radiation image with (SNR) = 1 can be only obtained when the pinhole diameter is 0.7 mm, object distance and image distance are both 200 cm, and the radiation intensity is about 1.0 × 1012 Sr-1·cm-2.展开更多
An image super resolution reconstruction method was used to improve the spatial resolution of the thick pinhole imaging system and to mitigate the limitations of the image spatial resolution of the hardware of the ima...An image super resolution reconstruction method was used to improve the spatial resolution of the thick pinhole imaging system and to mitigate the limitations of the image spatial resolution of the hardware of the image diagnostic system. The thick pinhole is usually applied into the diagnostics of the high energy neutron radiation image. Due to the impacts among its energy flux, spatial resolution and effective field of view, in dealing with the large area radiation source, the spatial resolution of the thick pinhole neutron image cannot meet the requirements for high precision modeling of the radiation source image. In this paper, the Lucy-Richardson image super resolution reconstruction method was used to simulate the thick pinhole imaging and super resolution image reconstruction. And the spatial resolution of the image could be increased by over three times after the image super resolution reconstruction. Besides, in dealing with the pseudo-noise, plum blossom shape appeared in the image super resolution reconstruction. The analysis of the source of the pseudo-noise was made based on the simulation of the image reconstruction under various conditions according to the characteristics of the thick pinhole image configuration.展开更多
基金supported by the National Natural Science Foundation of China under grant No.50674026the Postgraduate Foundation of Northeastern University in China under grant No.18702016the Innovational Experiment Plan of Undergraduate Student of China under grant No.071014506
文摘Al was prepared by a new method in molten salt at low temperature. Sintered alumina pellets were used as cathode; graphite rod was employed as anode; and the molten CaCl2-NaCl was the electrolyte. A constant 3.2 V voltage was applied in this experiment, and oxygen in solid alumina cathode was reduced by direct electrochemical deoxidation at 550℃. In this process, the current gradually decreased with increasing time and the alumina pellets became grey and porous. The metallic particles were obtained and characterized by XRD （X-ray diffraction） and SEM （scanning electron microscopy）.
基金This work was supported by the National Natural Science Foundation of China(Nos.41901073 and 52078435)the Sichuan Science and Technology Program(No.2021YJ0001)。
文摘Stress concentration occurs in the foundations of railway tracks where discontinuous components are located.The exacerbated stress under the expansion joints in slab tracks may trigger foundation failures such as mud pumping.Although the higher stress due to the discontinuities of track structures has been discussed in past studies,few focused on the stress response of roadbeds in slab tracks and quantitatively characterized the stress pattern.In this paper,we performed a dynamic finite element analysis of a track-formation system,incorporating expansion joints as primary longitudinal discontinuities.The configurations of CRTS Ⅲ slab tracks and the contact conditions between concrete layers were considered.Numerical results show that longitudinal influencing length of induced stress on roadbed under wheel load relates to the contact conditions between concrete layers,increasing nonlinearly at a larger coefficient of friction.Given a measured coefficient of friction of 0.7,the calculated longitudinal influencing length(9.0 m) matches with field data.The longitudinal influencing length is not affected with the increasing velocity.As stress concentration arises with expansion joints,the worstcase scenario emerges when double-axle loads are exerted immediately above the expansion joints between concrete bases.A stress concentration factor Cvon the roadbed is proposed;it increases with the increasing velocity,changing from 1.33 to 1.52 at velocities between 5 and 400 km/h.The stress distribution on roadbeds transforms from a trapezoid pattern at continuous sections to a triangle pattern at points with longitudinal discontinuities.An explicit expression is finally proposed for the stress pattern on roadbed under expansion joints.Although structural discontinuities induce stress raiser,the extent of concentration is mitigated with increasing depth at different velocity levels.
基金the financial support from the National Training Program of Innovation and Entrepreneurship for Undergraduates(201810145075)Fundamental Research Funds for the Central Universities(N172505002)+2 种基金NSFC(51704060)National Thousand Youth Talent Program of Chinathe 111 Project(B16009)
文摘Silicon(Si)and carbon(C)composites hold the promise for replacing the commercial graphite anode,thus increasing the energy density of lithium-ion batteries(LIBs).To mitigate the formation of SiC,this paper reports a molten salt electrolysis approach to prepare C-Si composite by the electrolysis of C-SiO2 composites.Unlike the conventional way of making a C coating on Si,C-SiO2 composites were prepared by pyrolyzing the low-cost sucrose and silica.The electrochemical deoxidation of the C-SiO2 composites not only produces nanostructured Si inside the C matrix but also introduces voids between the C and Si owing to the volume shrinkage from converting SiO2 to Si.More importantly,the use of Mg ion-containing molten salts precludes the generation of SiC,and the electrolytic Si@C composite anode delivers a capacity of about 1500 mAh g-1 after 100 cycles at a current density of 500 mA g-1.Further,the Si@C‖LiNi0.6Co0.2Mn0.2O2 full cell delivers a high energy density of 608 Wh kg-1.Overall,the molten salt approach provides a one-step electrochemical way to convert oxides@C to metals@C functional materials.
基金supported by the Specialized Research Fund for the Doctoral Program of Higher Education(20114307120032)the National Natural Science Foundation of China(71201167)
文摘A Bayesian method for estimating human error probability（HEP） is presented.The main idea of the method is incorporating human performance data into the HEP estimation process.By integrating human performance data and prior information about human performance together,a more accurate and specific HEP estimation can be achieved.For the time-unrelated task without rigorous time restriction,the HEP estimated by the common-used human reliability analysis（HRA） methods or expert judgments is collected as the source of prior information.And for the time-related task with rigorous time restriction,the human error is expressed as non-response making.Therefore,HEP is the time curve of non-response probability（NRP）.The prior information is collected from system safety and reliability specifications or by expert judgments.The（joint） posterior distribution of HEP or NRP-related parameter（s） is constructed after prior information has been collected.Based on the posterior distribution,the point or interval estimation of HEP/NRP is obtained.Two illustrative examples are introduced to demonstrate the practicality of the aforementioned approach.
文摘The spatial resolution of the gamma-rays camera was measured on a60Co gamma-rays source with edge method. The gamma-rays camera is consisting with rays-fluorescence convertor, optical imaging system, MCP image intensifier, CCD camera, electronic control system and other devices, and is mainly used in the image diagnostics of the intense pulse radiation sources [1]. Due to the relatively big quantum detective efficiency (DQE) and quantum gain of the gamma-rays, etc., the experimental data were processed by averaging multiple images and fitting curves. According to the experimental results, the spatial resolution MTF (modulation transfer function) at the 10% intensity was about 2lp/mm. Meanwhile, because of the relatively big dispersion effects of the fluorescence transmissions in the scintillator and the optical imaging system, the maximal single-noise ratio (SNR) of the camera was found to be about 5:1. In addition, the spatial resolution of the camera was measured with pulse X-rays with 0.3MeV in average energy and exclusion of the effects of secondary electrons from consideration. Accordingly, the spatial resolution MTF at the 10% intensity was about 5lp/mm. This could be an additional evidence to verify the effects of secondary electrons induced by the 1.25MeV gamma-rays in the scintillator upon the spatial resolution. Based on our analysis, the dispersion sizes of the secondary electrons in the scintillator are about 0.4mm-0.6mm. Comparatively, as indicated by the detailed analysis of the spatial resolutions of the MCP image intensifier and CCD devices, both of them have little effect on the spatial resolution of the gamma-rays camera that could be well neglected.
文摘The diagnostic methods for the profile of the radiation source were estab-lished at first based on the pinhole imaging principle. In this paper, the relationships among various parameters of the gamma-rays crammer such as the modulation transfer function (MTF), the noise power spectrum (NPS), the signal-noise ratio (SNR) and the detective quantum efficiency (DQE) are developed and studied experimentally on the cobalt radiation source. The image diagnostic system is consisting with rays-fluorescence convertor (YAG crystal), optical imaging system, MCP image intensifier, CCD camera and other devices. The spatial resolution of the modulation transfer function (MTF) at 10% intensity was measured as 1 lp/mm by knife-edge method. The quantum of the measurement system is about 150 under weak radiation condition due to the single particle detection efficiency of the system. The dynamic range was inferred preliminarily as about 437. The required radiation intensity was calculated using the experiment result for the (SNR) = 1, 5, 10, respectively. The theoretical investigation results show that the radiation image with (SNR) = 1 can be only obtained when the pinhole diameter is 0.7 mm, object distance and image distance are both 200 cm, and the radiation intensity is about 1.0 × 1012 Sr-1·cm-2.
文摘An image super resolution reconstruction method was used to improve the spatial resolution of the thick pinhole imaging system and to mitigate the limitations of the image spatial resolution of the hardware of the image diagnostic system. The thick pinhole is usually applied into the diagnostics of the high energy neutron radiation image. Due to the impacts among its energy flux, spatial resolution and effective field of view, in dealing with the large area radiation source, the spatial resolution of the thick pinhole neutron image cannot meet the requirements for high precision modeling of the radiation source image. In this paper, the Lucy-Richardson image super resolution reconstruction method was used to simulate the thick pinhole imaging and super resolution image reconstruction. And the spatial resolution of the image could be increased by over three times after the image super resolution reconstruction. Besides, in dealing with the pseudo-noise, plum blossom shape appeared in the image super resolution reconstruction. The analysis of the source of the pseudo-noise was made based on the simulation of the image reconstruction under various conditions according to the characteristics of the thick pinhole image configuration.
